This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements
This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements
This motor MCC Panel is exclusive tailor made product & is designed as per requirement of customer. Nos. of motors are started from this panel center & mostly these are DOL or Star- delta Starter motors. All the push buttons & indicators are mounted on panel or remote controlled. Features: Simplex & Duplex pattern Degree of Protection: IP-42 to IP-65 Painting: Powder Coating / Spray Paint / Epoxy Paint Compartmentalized design eliminates risk to maintenance personal Sufficient space for incoming and outgoing cables Provided with buzzer & hooter during emergency Separate Bus bar and cable chambers Motor Control Center shall have hinged door with lockable arrangement Motor Control Center Available with Aluminum / copper bus bar Motor Control Center is suitable for use on 415V, 3 Phase, 4 wire, 50Hz Application: These are widely used for: Protection against electrical Short Circuit, overload and earth fault of the system Control & monitoring of the entire electrical system of an industry / plant Systematic power catering to various load of an electrical system Normally used in Hospitals, Multi-storied buildings, steel industries, cement industry, open â??cast mines, shopping mall etc. We offer the following options and facilities: ASTA certified bus bar systems (50 KA for 1 sec as standard). Separation: Form 4 Type 2 as standard but types 3, 6 and 7 available if required Ingress protection up to IP 65 Wall mounting or floor standing Top, bottom or special cable entry Front or rear cabling access Fixed, plug in or with drawable type Full range of instruments and metering to customers requirements Contactor, soft start and variable speed drives Local or remote control Wired to separate terminal chambers Facilities for thermal imaging Local or remote manual controls Relay or PLC automatic controls Alarm systems Alarm annunciators BMS interface Special control systems to customers requirements
Ceramic Frit Glass Ceramic frit glass, also known as fritted glass, is a specialized type of architectural glass that has been processed with ceramic fritting. This process involves applying a ceramic enamel frit (a powdered glass mixture) to the surface of the glass and then heating it to fuse the frit onto the glass substrate. This results in a range of unique properties and applications. Here are some key aspects of ceramic frit glass Solar Control: Ceramic frit glass is often used to control solar heat gain in buildings. The fritted pattern on the glass can be customized to allow varying levels of sunlight to pass through while reducing heat transmission. This enhances energy efficiency by minimizing the need for air conditioning and artificial lighting. Privacy: The fritted pattern can be designed to provide privacy by obscuring the view from outside while maintaining natural light inside. This is commonly used in office buildings and residential spaces, particularly in urban settings. Aesthetics: Ceramic frit glass offers design versatility. It can be customized with various patterns, colors, and opacities to create visually appealing and distinctive facades, partitions, and windows. It allows architects and designers to achieve both functional and aesthetic goals. Glare Reduction: The fritting process can reduce glare caused by direct sunlight, creating a more comfortable indoor environment in spaces with large windows or glass facades. UV Protection: Ceramic fritted glass can provide protection against harmful ultraviolet (UV) radiation, safeguarding interior furnishings and artworks from fading or damage. Durability: The ceramic enamel frit is highly durable and resistant to wear, ensuring the pattern remains intact over time. It is also resistant to weathering, making it suitable for exterior applications.
TECHNICAL SPECIFICATION OF 150KVA THREE PHASE OIL COOLED SERVO VOLTAGE STABILIZER 1. Capacity : 150KVA Three Phase 2. Model : Make SERVOSINE 3. Input Voltage Range : 190V-270V 1Phase / 340V-470V 3 Phase 4. Output Voltage : 230V +/-1% 1 PH / 400V +/-1% 3 PH 5. No. of phases : Three, 4 Wire 6. Line Frequency : 47-53Hz. 7. Output Voltage Regulation : +1% 8. Type of Cooling : Oil Cooled 9. Type : Unbalanced supply and Load conditions 10. Efficiency :> 98% 11. Speed of Correction : 30V per sec (For 3 Phase) 12. Wave form distortion : Nil 13. Effect of Load power factor : Nil, Suitable for all power factors 14. Ambient Temperature : 0-65�ºC with RH 90% 15. Duty Cycle : Continuous 16. Indications on each phase : Input Mains, Input Low, Input Voltage, Input High, Out Voltage. 17. Controls on each Phase : Auto/Manual Push Button, Increase/Decrease Push Button Voltâ??s adjuster Set Button 18. Metering : Digital 19. Mounting : On Wheel 20. Construction : MS Sheet Body, Prime Grade Powder Coating 21. Spares Availability : Available with Company 22. Transformer Winding : Prime Grade Copper Wire on CRGO Core 23. Servicing & Maintenance : Easley can be do by any technical known Person And from company side on call log.
TECHNICAL SPECIFICATION OF 100KVA THREE PHASE OIL COOLED SERVO VOLTAGE STABILIZER 1. Capacity : 100KVA Three Phase 2. Model : Make SERVOSINE 3. Input Voltage Range : 190V-270V 1Phase / 340V-470V 3 Phase 4. Output Voltage : 230V +/-1% 1 PH / 400V +/-1% 3 PH 5. No. of phases : Three, 4 Wire 6. Line Frequency : 47-53Hz. 7. Output Voltage Regulation : +1% 8. Type of Cooling : Oil Cooled 9. Type : Unbalanced supply and Load conditions 10. Efficiency :> 98% 11. Speed of Correction : 30V per sec (For 3 Phase) 12. Wave form distortion : Nil 13. Effect of Load power factor : Nil, Suitable for all power factors 14. Ambient Temperature : 0-65C with RH 90% 15. Duty Cycle : Continuous 16. Indications on each phase : Input Mains, Input Low, Input Voltage, Input High, Out Voltage. 17. Controls on each Phase : Auto/Manual Push Button, Increase/Decrease Push Button Volt adjuster Set Button 18. Metering : Digital 19. Mounting : On Wheel 20. Construction : MS Sheet Body, Prime Grade Powder Coating 21. Spares Availability : Available with Company 22. Transformer Winding : Prime Grade Copper Wire on CRGO Core 23. Servicing & Maintenance : Easley can be do by any technical known Person And from company side on call log.
Technical Specification Of 75kva Three Phase Oil Cooled Servo Voltage Stabilizer 1. Capacity : 75KVA Three Phase 2. Model : Make SERVOSINE 3. Input Voltage Range : 190V-270V 1Phase / 340V-470V 3 Phase 4. Output Voltage : 230V +/-1% 1 PH / 400V +/-1% 3 PH 5. No. of phases : Three, 4 Wire 6. Line Frequency : 47-53Hz. 7. Output Voltage Regulation : +1% 8. Type of Cooling : Oil Cooled 9. Type : Unbalanced supply and Load conditions 10. Efficiency :> 98% 11. Speed of Correction : 30V per sec (For 3 Phase) 12. Wave form distortion : Nil 13. Effect of Load power factor : Nil, Suitable for all power factors 14. Ambient Temperature : 0-65�ºC with RH 90% 15. Duty Cycle : Continuous 16. Indications on each phase : Input Mains, Input Low, Input Voltage, Input High, Out Voltage. 17. Controls on each Phase : Auto/Manual Push Button, Increase/Decrease Push Button Voltâ??s adjuster Set Button 18. Metering : Digital 19. Mounting : On Wheel 20. Construction : MS Sheet Body, Prime Grade Powder Coating 21. Spares Availability : Available with Company 22. Transformer Winding : Prime Grade Copper Wire on CRGO Core 23. Servicing & Maintenance : Easley can be do by any technical known Person And from company side on call log.
TECHNICAL SPECIFICATION 1. Capacity : 50KVA Three Phase 2. Model : Make SERVOSINE 3. Input Voltage Range : 190V-270V 1Phase / 340V-470V 3 Phase 4. Output Voltage : 230V +/-1% 1 PH / 400V +/-1% 3 PH 5. No. of phases : Three, 4 Wire 6. Line Frequency : 47-53Hz. 7. Output Voltage Regulation : +1% 8. Type of Cooling : Oil Cooled 9. Type : Unbalanced supply and Load conditions 10. Efficiency :> 98% 11. Speed of Correction : 30V per sec (For 3 Phase) 12. Wave form distortion : Nil 13. Effect of Load power factor : Nil, Suitable for all power factors 14. Ambient Temperature : 0-65 C with RH 90% 15. Duty Cycle : Continuous 16. Indications on each phase : Input Mains, Input Low, Input Voltage, Input High, Out Voltage. 17. Controls on each Phase : Auto/Manual Push Button, Increase/Decrease Push Button Voltâ??s adjuster Set Button 18. Metering : Digital 19. Mounting : On Wheel 20. Construction : MS Sheet Body, Prime Grade Powder Coating 21. Spares Availability : Available with Company 22. Transformer Winding : Prime Grade Copper Wire on CRGO Core 23. Servicing & Maintenance : Easley can be do by any technical known Person And from company side on call log.
Silicon Carbide Heating ElementDescription Silicon Carbide Heating Element can be installed and replaced while the tin bath is operation. The heaters can be installed through the side-seal, or through the side of the bath roof, and are commonly used to extend campaign lives, where conventional elements in the side zones have been broken, and insufficient power is available. Silicon Carbide Heating Element Advantages High purity raw materials; High structural density; Slow aging; Maximum temperature being up to 1500â?? (2732�°F); Easy to be installed and replaced. Types and Applications of Silicon Carbide Heating Element 1. SW (Standard) SW Silicon Carbides are used in applications ranging in temperature from 600�°C up to 1400�°C in both air and controlled atmospheres. Although the type of atmosphere used will determine the maximum recommended element temperature. This kind of silicon carbide elements can be mounted either vertically or horizontally. 2. U-TYPE U shape Silicon Carbide is consists of two silicon carbide rod with same diameter. Each rod has both hot zone and cold end with identical resistance. Two rods are connected by the low resistance SiC. Also the connector could be used as holder according to different requirements. 3. W-TYPE 3-phase elements are available in 2 different types: SGC (Dumbbell), SGD(Standard). These elements are self-bonded silicon carbide formed by re-crystallization of silicon carbide at high temperature. It consists of three high-purity silicon carbide rods connected at one end by a silicon carbide crossbar. SGC elements are designed for vertical installation in standard float glass bathes and SGD elements for horizontal installation. They can be connected directly on three-phase power supply and is a one-side terminal type which permits drawing out the terminals from the roof of the furnace. 4. Single Spiral Silicon Carbide and Double Spiral Silicon Carbide: They are made from silicon Carbide powder, and have two shapes: single and double sprial silicon carbide heating element. They are widely used in all kinds of kilns and furnaces.
Silicon Carbide Heating Element General Description Silicon carbide heating element is a kind of non-metal high temperature electric heating element. It is made of selected high quality green silicon carbide as main material, which is made into blank, siliconization under high temperature and recrystallized. It is the most popular type of economical heating element capable of operating under hot and rigorous environments. Silicon Carbide Heating Element Features 1. withstands as high as 1600�°C 2. high strength and excellent shock resistance 3. heat source is free of noise and air pollution 4. anti-oxidization, anti- corrosion 5. easy to installation and maintenance Applications of Silicon Carbide Heating Element There are ED, U, W, H, Gun, Single Spiral, Double Spirals, Dumbbel, Door-like types and etc. which are widely used in various high temperature electric furnaces in air, vacuum and other protection gas environments and other electric heating devices, such as industries of magnet, ceramics, powder metallurgy, glass and machinery, etc. Silicon Carbide Heating Elements Complete Specifications 0 Silicon Carbide Heating Elements Complete Specifications 1 Normally the following should be given when describing any type of SiC heating elements: Type: ED, U, W, SC, SCR, DB,G, H, or DM Outside Diameter (OD) : mm Length of Hot Zone (HZ) :mm Length of Cold Zone (CZ) :mm Length of Overall(OL):mm Center Distance (A) :mm Resistance at 105050 Physical property of SIC heating element specific gravity 2628gcm bend strength 300kg hardness 9MOHS tensile strength 150kgcm porosity rate
100 Amp 3 ph Motorized Control Digital Variable Voltage Auto Transformer [Oil Immersed] [HSN CODE: 85044029] [Make: POWERSELECT] Technical Specification: Model: PS100A3POEM470V Rated Power: 75 KVA Input Voltage: 415 V AC 3phase�¸ (L - L), �±5% 50 / 60 Hz 4 wire / 3 wire No Load Current: Less than 1% of rated unit Output Voltage: 0 - 470 V AC 3Phase�¸, (L - L) �±10% 4 wire / 3 wire Output Current @470V: 0 - 100 Amp per phase max Variac Oil Qty: 200 L (Approx. +- 10 L) Recommended IS335 Reference Standard: IEC 61378-1 & IS 5142 : 1969 Voltage Variation: Motorized Operation with 10 kg torque AC Synchronous Servo Motor Servo Motor: 10 Kg torque AC Synchronous Servo Motor 220 V AC 1 ph. (Make: PowerSelect) Coil Construction: 1 Coils used in per phase of 100 Amp each rating Total Coils: 3 Coils used in unit each coil rating max 100 Amp Current Transformer: 3 nos. 100/5 Accuracy class 0.5% Protection: 3 pole MCCB on Primary line (Make: L&T) Enclosure IP Rating: IEC 60529, IP50 (Sheet Steel) with powder coated paint (Color: Siemens Gray) Connection Terminals: DMC molded bar insulators terminal Oil Drain: Oil Drain valve tap bottom of tank front sided Oil Level: Oil level indication front of tank with glass view Earth Terminals: Ground / earth terminals provided back sided Winding Wire: IS 12444, ASTM B-49 Pure Copper DCC wire Core Type, Grade of lamination: CRGO Laminated Core 30ZH100 Load : balanced load Service: Indoor Application Variac Dimension (LxBxH) and Wt (Kg): 24 x 32 x 50 (Approx) Net Wt: 250 Kg (Approx.) Gross Weight: 350 kg
Company Information Shaoyang Zhongcai Manufacturing Co.,Ltd is specialized in pigment business. We supply various kinds of pigments which is well used in the industries of paint,printing ink,plastic,rubber and building materials,etc. We devote ourself for exporting,.88% of our products are exported to United State,Europe,America,Southeast Asia India,etc. We save no efforts to serve our customers with Consistent quality,Competitive price,Punctual Shipment,Strictly after-sales quality traking. Paying more attention to customer's benefit,find more economical solution for all our customers is our company mission.Company Information: Shaoyang Zhongcai Manufacturing Co.,Ltd is specialized in pigment business. We supply various kinds of pigments which is well used in the industries of paint,printing ink,plastic,rubber and building materials,etc. We devote ourself for exporting,.88% of our products are exported to United State,Europe,America,Southeast Asia India,etc. We save no efforts to serve our customers with Consistent quality,Competitive price,Punctual Shipment,Strictly after-sales quality traking. Paying more attention to customer's benefit,find more economical solution for all our customers is our company mission. Property: 1. Powder of brilliant colors. Eye-pleasing and perdurable. 2. Strong coloring power, good covering power, and good dispersibility. 3. Light permanency and weatherability. Specification H110 and H120 gao xing zhong cai : ITEM H110 H120 Fe2O3 content 95% Min 95% Min Volatile 105�?? 1% Max 1% Max Water solubility 0.3% Max 0.3% Max Residue after sieve(mesh 325 wet sieve) 0.3% Max 0.3% Max PH value 4-7 4-7 Oil absorption 15-25 15-25 Color light(compare with standard sample) Similar-light Similar-light Tinting Strength 95% Minimum 95% Minimum
Custom MIM PM pats by drawings for Automobile metal parts, airbag components,Ignition control lock component,Turbocharged rotor All the profucts can process by customization. Please send me the 2D and 3D drawings with size and tolerance. We will evaluate the drawings for you and process according to the drawings. And we will keep the drawings strictly confidential. Customers can also choose processing methods With over 20 years experience, ShenZhen YuJiaXin Hardware Products Co., Ltd. is a leading manufacturer of precision metal parts in China, we provide products to consumer electronics, automotive, medical, and industrial. Metal Injection Molding,or MIM,is a new Powder Metallurgy process that can produce sintered componects with high densety and complicated shapes without the need for machining. With its unique characteristics, MIM is capable of producing precise metal parts for a wide range of products, including automobiles, cellular phones,hand tools,dental instruments,pneumatic tools, power hand tools, surgical instruments,sporting goods, and laptop computers. The common materials used in MIM range from stainless steels and alloy steels to soft magnetic matericals. Metal injection molding (MIM) is an effective way to produce complex and precision-shaped parts from a variety of materials. This process produces parts for 50% less than the cost of CNC machining or casting. MIM is able to produce parts with complex shapes, superior strength and excellent surface finish with high volume manufacturing.High volumes are attained through multi-cavity tooling. From design and tooling to production and quality engineering with in-depth technical and engineering expertise. Our business model is designed to meet the portfolio of parts that global OEMs will source in China. Our facility is growing rapidly, and adding new capabilities in a very short span of time. Please contact us to understand our current state of completion and new capabilities that we plan to add.
All the profucts can process by customization. Please send me the 2D and 3D drawings with size and tolerance. We will evaluate the drawings for you and process according to the drawings. And we will keep the drawings strictly confidential. Customers can also choose processing methods a leading manufacturer of precision metal parts , we provide products to consumer electronics, automotive, medical, and industrial. a new Powder Metallurgy process that can produce sintered componects with high densety and complicated shapes without the need for machining. With its unique characteristics, MIM is capable of producing precise metal parts for a wide range of products, including automobiles, cellular phones,hand tools,dental instruments,pneumatic tools, power hand tools, surgical instruments,sporting goods, and laptop computers. The common materials used in MIM range from stainless steels and alloy steels to soft magnetic matericals. Metal injection molding (MIM) is an effective way to produce complex and precision-shaped parts from a variety of materials. This process produces parts for 50% less than the cost of CNC machining or casting. MIM is able to produce parts with complex shapes, superior strength and excellent surface finish with high volume manufacturing.High volumes are attained through multi-cavity tooling. From design and tooling to production and quality engineering with in-depth technical and engineering expertise. Our business model is designed to meet the portfolio of parts that global OEMs will source . Our facility is growing rapidly, and adding new capabilities in a very short span of time. Please contact us to understand our current state of completion and new capabilities that we plan to add.
All the profucts can process by customization. Please send me the 2D and 3D drawings with size and tolerance. We will evaluate the drawings for you and process according to the drawings. And we will keep the drawings strictly confidential. Customers can also choose processing methods a leading manufacturer of precision metal parts , we provide products to consumer electronics, automotive, medical, and industrial. a new Powder Metallurgy process that can produce sintered componects with high densety and complicated shapes without the need for machining. With its unique characteristics, MIM is capable of producing precise metal parts for a wide range of products, including automobiles, cellular phones,hand tools,dental instruments,pneumatic tools, power hand tools, surgical instruments,sporting goods, and laptop computers. The common materials used in MIM range from stainless steels and alloy steels to soft magnetic matericals. Metal injection molding (MIM) is an effective way to produce complex and precision-shaped parts from a variety of materials. This process produces parts for 50% less than the cost of CNC machining or casting. MIM is able to produce parts with complex shapes, superior strength and excellent surface finish with high volume manufacturing.High volumes are attained through multi-cavity tooling. From design and tooling to production and quality engineering with in-depth technical and engineering expertise. Our business model is designed to meet the portfolio of parts that global OEMs will source . Our facility is growing rapidly, and adding new capabilities in a very short span of time. Please contact us to understand our current state of completion and new capabilities that we plan to add.
All the profucts can process by customization. Please send me the 2D and 3D drawings with size and tolerance. We will evaluate the drawings for you and process according to the drawings. And we will keep the drawings strictly confidential. Customers can also choose processing methods a leading manufacturer of precision metal parts , we provide products to consumer electronics, automotive, medical, and industrial. a new Powder Metallurgy process that can produce sintered componects with high densety and complicated shapes without the need for machining. With its unique characteristics, MIM is capable of producing precise metal parts for a wide range of products, including automobiles, cellular phones,hand tools,dental instruments,pneumatic tools, power hand tools, surgical instruments,sporting goods, and laptop computers. The common materials used in MIM range from stainless steels and alloy steels to soft magnetic matericals. Metal injection molding (MIM) is an effective way to produce complex and precision-shaped parts from a variety of materials. This process produces parts for 50% less than the cost of CNC machining or casting. MIM is able to produce parts with complex shapes, superior strength and excellent surface finish with high volume manufacturing.High volumes are attained through multi-cavity tooling. From design and tooling to production and quality engineering with in-depth technical and engineering expertise. Our business model is designed to meet the portfolio of parts that global OEMs will source . Our facility is growing rapidly, and adding new capabilities in a very short span of time. Please contact us to understand our current state of completion and new capabilities that we plan to add.
1  Type Specification: 2. Application: for making cutting tools, for example end mills, dental burs, reamer etc. 3. Diameter: 0.3mm to 50mm 4. Length: standard 330mm/310mm or customized 5. Surface: blank or ground 6. Material: WC+CO What is tungsten carbide rod?� Tungsten carbide rod, also called carbide round bar,� cemented carbide rod,� is a high-strength and high-hardness material which has a major raw material of WC, with other metals and paste phases using powder metallurgical methods through low-pressure sintering. What is the value of cemented carbide rods? Tungsten carbide rod is the preferred material for metal cutting tool manufacturing, widely used in the industries which has high requirements for wear-resistance, corrosion-resistance and high-temperature resistance. It has a lot of outstanding performances. What are the uses of tungsten carbide rods? Carbide rods can be used not only for cutting and drilling tools (such as micron, twist drills, drill vertical mining tool specifications), but also for input needles, various roll worn parts and structural materials. In addition, it can be used in many fields, such as machinery, chemical, petroleum, metallurgy, electronics and defense industries. Zhuzhou Better produces a wide range of tungsten carbide rods products with various grades, including carbide rods� with central coolant hole, two holes helical rods and three holes helical rods.
All the profucts can process by customization. Please send me the 2D and 3D drawings with size and tolerance. We will evaluate the drawings for you and process according to the drawings. And we will keep the drawings strictly confidential. Customers can also choose processing methods With over 20 years experience, ShenZhen YuJiaXin Hardware Products Co., Ltd. is a leading manufacturer of precision metal parts in China, we provide products to consumer electronics, automotive, medical, and industrial. Metal Injection Molding,or MIM,is a new Powder Metallurgy process that can produce sintered componects with high densety and complicated shapes without the need for machining. With its unique characteristics, MIM is capable of producing precise metal parts for a wide range of products, including automobiles, cellular phones,hand tools,dental instruments,pneumatic tools, power hand tools, surgical instruments,sporting goods, and laptop computers. The common materials used in MIM range from stainless steels and alloy steels to soft magnetic matericals. Metal injection molding (MIM) is an effective way to produce complex and precision-shaped parts from a variety of materials. This process produces parts for 50% less than the cost of CNC machining or casting. MIM is able to produce parts with complex shapes, superior strength and excellent surface finish with high volume manufacturing.High volumes are attained through multi-cavity tooling. From design and tooling to production and quality engineering with in-depth technical and engineering expertise. Our business model is designed to meet the portfolio of parts that global OEMs will source in China. Our facility is growing rapidly, and adding new capabilities in a very short span of time. Please contact us to understand our current state of completion and new capabilities that we plan to add.
All the profucts can process by customization. Please send me the 2D and 3D drawings with size and tolerance. We will evaluate the drawings for you and process according to the drawings. And we will keep the drawings strictly confidential. Customers can also choose processing methods With over 20 years experience, ShenZhen YuJiaXin Hardware Products Co., Ltd. is a leading manufacturer of precision metal parts in China, we provide products to consumer electronics, automotive, medical, and industrial. Metal Injection Molding,or MIM,is a new Powder Metallurgy process that can produce sintered componects with high densety and complicated shapes without the need for machining. With its unique characteristics, MIM is capable of producing precise metal parts for a wide range of products, including automobiles, cellular phones,hand tools,dental instruments,pneumatic tools, power hand tools, surgical instruments,sporting goods, and laptop computers. The common materials used in MIM range from stainless steels and alloy steels to soft magnetic matericals. Metal injection molding (MIM) is an effective way to produce complex and precision-shaped parts from a variety of materials. This process produces parts for 50% less than the cost of CNC machining or casting. MIM is able to produce parts with complex shapes, superior strength and excellent surface finish with high volume manufacturing.High volumes are attained through multi-cavity tooling. From design and tooling to production and quality engineering with in-depth technical and engineering expertise. Our business model is designed to meet the portfolio of parts that global OEMs will source in China. Our facility is growing rapidly, and adding new capabilities in a very short span of time. Please contact us to understand our current state of completion and new capabilities that we plan to add.
All the profucts can process by customization. Please send me the 2D and 3D drawings with size and tolerance. We will evaluate the drawings for you and process according to the drawings. And we will keep the drawings strictly confidential. Customers can also choose processing methods With over 20 years experience, ShenZhen YuJiaXin Hardware Products Co., Ltd. is a leading manufacturer of precision metal parts in China, we provide products to consumer electronics, automotive, medical, and industrial. Metal Injection Molding,or MIM,is a new Powder Metallurgy process that can produce sintered componects with high densety and complicated shapes without the need for machining. With its unique characteristics, MIM is capable of producing precise metal parts for a wide range of products, including automobiles, cellular phones,hand tools,dental instruments,pneumatic tools, power hand tools, surgical instruments,sporting goods, and laptop computers. The common materials used in MIM range from stainless steels and alloy steels to soft magnetic matericals. Metal injection molding (MIM) is an effective way to produce complex and precision-shaped parts from a variety of materials. This process produces parts for 50% less than the cost of CNC machining or casting. MIM is able to produce parts with complex shapes, superior strength and excellent surface finish with high volume manufacturing.High volumes are attained through multi-cavity tooling. From design and tooling to production and quality engineering with in-depth technical and engineering expertise. Our business model is designed to meet the portfolio of parts that global OEMs will source in China. Our facility is growing rapidly, and adding new capabilities in a very short span of time. Please contact us to understand our current state of completion and new capabilities that we plan to add.
