Silicon Carbide Heating Elements

SiC heating element Silicon Carbide (SiC) heating element is a non-metal electric heating element made from SiC as its main raw materials. It has some specific properties, such as low expansion coefficient, little deformation, stable chemical property, long service life, easy installation and maintenance

Supplier: Silicon carbide heating elements, silicon carbide heater, SIC heating elements, SIC heater, silicon carbide rod, SIC rod, molybdenum disilicide heating elements, molybdenum disilicide heater, mosi2 heating elements, mosi2 heater, molybdenum disilicide rod, mosi2 rod, thermocouple protecting tube, thermocouple element

Silicon Carbide Heating ElementDescription Silicon Carbide Heating Element can be installed and replaced while the tin bath is operation. The heaters can be installed through the side-seal, or through the side of the bath roof, and are commonly used to extend campaign lives, where conventional elements in the side zones have been broken, and insufficient power is available. Silicon Carbide Heating Element Advantages High purity raw materials; High structural density; Slow aging; Maximum temperature being up to 1500â?? (2732�°F); Easy to be installed and replaced. Types and Applications of Silicon Carbide Heating Element 1. SW (Standard) SW Silicon Carbides are used in applications ranging in temperature from 600�°C up to 1400�°C in both air and controlled atmospheres. Although the type of atmosphere used will determine the maximum recommended element temperature. This kind of silicon carbide elements can be mounted either vertically or horizontally. 2. U-TYPE U shape Silicon Carbide is consists of two silicon carbide rod with same diameter. Each rod has both hot zone and cold end with identical resistance. Two rods are connected by the low resistance SiC. Also the connector could be used as holder according to different requirements. 3. W-TYPE 3-phase elements are available in 2 different types: SGC (Dumbbell), SGD(Standard). These elements are self-bonded silicon carbide formed by re-crystallization of silicon carbide at high temperature. It consists of three high-purity silicon carbide rods connected at one end by a silicon carbide crossbar. SGC elements are designed for vertical installation in standard float glass bathes and SGD elements for horizontal installation. They can be connected directly on three-phase power supply and is a one-side terminal type which permits drawing out the terminals from the roof of the furnace. 4. Single Spiral Silicon Carbide and Double Spiral Silicon Carbide: They are made from silicon Carbide powder, and have two shapes: single and double sprial silicon carbide heating element. They are widely used in all kinds of kilns and furnaces.

Zgs066-047c: Material: sus304, bluing Outer ring voltage and power: 230v 900w Inner ring voltage and power: 230v 1350w Outside diameter: f6.6mm Surface load: =5.5w/cm2 Working life: =3000 hours Cold insulation: more than 50 mo Electric heating tube life: =3000 hours Application: oven Heating tube end-use condition: heated air When using the rated voltage, leakage current is less than 0.5ma Withstand voltage: cold condition 1800v/0.5ma/1s no breakdown. Heat condition 1250v/0.5ma/1s no breakdown. The installation and outside dimension is subject to the client’s requirement - Material: sus304, bluing Outer ring voltage and power: 230v 900w Inner ring voltage and power: 230v 1350w Outside diameter: f6.6mm Surface load: =5.5w/cm2 Working life: =3000 hours Cold insulation: more than 50 mo Electric heating tube life: =3000 hours Application: oven Heating tube end-use condition: heated air When using the rated voltage, leakage current is less than 0.5ma Withstand voltage: cold condition 1800v/0.5ma/1s no breakdown. Heat condition 1250v/0.5ma/1s no breakdown. The installation and outside dimension is subject to the client’s requirement

Quality: long using life gurantee Placed postion: 1) Horizontal 2) Upright

Mosi2 electrical heating element MoSi2 electrical-heating element is a resistance generate-heating component made from MoSi2 or the basic material. It is used in high temperature under the oxidizing atmosphere, it looks like glass in its surface and forms a light SiO2 glass film which can protect the element not to be oxidized. So this kind of element has unique effect for resisting oxidization in the high temperature. It is used to the highest temperature up to 1800f¦ during oxidizing atmosphere. According to your request, our company can produce the products of Pole, "U", "W" and "U"-right angle shapes

Electric heating element restrings HVAC PART FURNACE 1/2" 5KW + Directions. As several former cooking ingredients are no longer accessible or very expensive, your money-saving alternative choice may be to restore them using a restring kit. Most restring kits come with a fuse.