Thread Work Silk Double Bed Sheet Suppliers and Manufacturers

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Caustic Soda Flakes Caustic Soda Pearls / Bead / Prill / Granule Caustic Soda solid Molecular formula: NaOH Molecule Weight: 40 H.S code: 28151100 CAS: 1310-73-2 UN number 1823 Dangerous Class 8 We use rich natural gas resources and its strategic of liquid alkali procurement, storage, transport conditions, gradually formed transportation and sale of liquid alkali, production and sales base Specifications(Caustic Soda Pearls 99%min): 1. Item: STANDARD 2. NaOH: 99% 3. Na2CO3:0.5%max 4. NaCL:0.03%max 5. Fe2O3: 0.005%max Packing in 25KG net PP bag lined with double PE inner bags. Specifications(Caustic Soda Flakes 99%min) 1. Item: Standard 2. NaOH: 99%min 3. Na2CO3: 0.5%max 4. NaCL:0.05%max 5. Fe2O3:0.005%max Packing in 25KG net PP bag lined with double PE inner bags. Specifications(Caustic Soda Solid 99%min) 1. Item: Standard 2. NaOH: 99%min 3. Na2CO3: 0.9%max 4. NaCL:0.15%max 5. Fe2O3: 0.01%max Packing in 200KG net sheet metal drugs.

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

Double-knife meat cutter Imitation hand meat and vegetable chopping machine It is a necessary equipment for catering chain stores can cutting meat vegetable with different food material mixing ,delicious stuffing. Capacity 60-70kg/hour ,good -looking appearance design as human working,sanitary,high efficient,save investing cost,high profit !

Meat dicer cutter machine is one of the common machines in the meat processing industry. They can quickly and accurately cut large pieces of meat, such as beef, pork, lamb, or poultry, into small diced pieces for subsequent cooking or process purpose . Machine size : 1480*800*1000mm 1950*1000*1120mm Cutting groove 84*84*350mm 120*120*550mm Cutting grating 5/6/7/8/10/12/14/21/24/28/30mm working power 3kw/380v 3.7kw/380v machine weight 500kg 700kg capacity 500-600kg/h 700-900kg/h Our meat dicer cutter machine is suitable for large factories, mining enterprises, universities, government cafeterias, central kitchens, fast food companies, food factories, fresh supermarkets, meat product factories, semi-finished product processing and distribution places, etc 304 stainless steel, it can accurately cut into shapes such as dice, silk, and strips. It is an important equipment in the production process of meat products. It can cut the main raw materials such as meat pieces, minced meat, and fat into the diced meat that users need. The size and style of the diced meat are determined by the tool switch, with high work efficiency, large output, easy maintenance, simple tool disassembly and cleaning, and can meet the production needs of a large number of users.

Acid etched glass is annealed glass treated with acid to give its surface a frosted look. Entire sheets of glass can be acid etched, or small sections can be treated to add specific designs. It make glass artistic, beautiful and long lasting. Normal acid etched glass can be used to create doors, partitions, walls, shelves, and railings, special items can be used as â??anti-glare glassâ?? for picture frame, screen, etc. Product items :� single side acid etched glass / double side acid etched glass Thickness :2-19mm Size :2440x3660mm 2140x3300mm,1830x2440mm,1220x1830mm, any cut sizes

JH acid etched glass is annealed glass treated with acid to give its surface a frosted look.Entire sheets of glass can be acid etched,or small sections can be treated to add specific designs. It make glass artistic ,beautiful and long lasting .Normal acid etched glass can be used to create doors,partitions,walls,shelves,and railings, special items can be used as �?�¢??anti-glare glass�?�¢?? for picture frame , screen ,etc. Product items : single side acid etched glass / double side acid etched glass Thickness :2-19mm Size :2440x3660mm 2140x3300mm,1830x2440mm,1220x1830mm , cut sizes