Size: 2"~36" Pressure Class: ANSI 150lb ~ 2500lb Design Standards: API 6D,ASME B16.34 Body Material: Carbon steel, Stainless steel, Alloy steel, Duplex stainless steel Trim: Soft sealing, Metal-Metal sealing End Connection: RF,RTJ,BW,FF Type of Operator: Gear, Motor Operator, Pneumatic Operator
Mtp opti-flow 380 series direct acting pressure relief valve and vacuum relief valve, or breather valve are special types of relief valve which are specifically designed for tank protection.Re We offer a free valve sizing service, let us advise you on the best solution for you tank The valves are available in a number of combinations illustrated below. Click on any for more information Pressure and vacuum breather valves Presure only breather valves Vacuum only breather valves Spring loaded relief valves Pilot operated valves All of the above combinations are available in a range of sizes and can have flanged outlets or vent to atmosphere on both the pressure and vacuum depending upon your requirements. These are some of the options available for our breather valves. Available in aluminium, cast iron, carbon steel, stainless steel & other metals upon request Valve sizes from 50mm (2ì) to 300mm (12ì) We will line and coat valves if this is required Valve sizing available, let our software do your valve sizing and recomend your solution Flow curves available for all our breather valves, Full range of breather valve spares available Breather valve servicing and resetting available upon request
-Operates hydraulically independent from any external power sources and controls high and low levels in a storage tank by utilizing the line static and dynamic pressure. -The incorporation of a control shaft in the valve bonnet allows the rate of flow through the valve to be set a pre-determined flow and also acts as a mechanical shut off feature. -Closing speed of the valve can be controlled by an integral needle valve on the valve bonnet. -The valve is easy to maintain and install due to its simple design.
Gate valve: Solid wedge and flexible wedge disk Parallel slide disk Double disk Globe valve: T-pattern, Y pattern Bellows seal type Metal diaphragm type Angle type Check valve: Swing check and lift check Tilting disk check Non-return type/stop check Balanced disk type(open and remain at 1.5 gpm) Testable check valve: Control tyope cracking pressure check valve Special valve: Flap check valve Continuous blow down valve Drain valve(for high pressure admission line) Controlled closure check valve(CCCV) Bleed trip valve(Reverse current check valve) Feed water heater level control valve Re-heater spray injection control valve Super heater spray injection control valve Boiler feed water pump minimum flow control valve Electromagnet operated valve(power control valve). Export standard packing.
Chemical Valves Fine chemical industry is a comprehensive and technology-intensive industry. In the production process, the technological process is long, the unit reaction is many, the raw material is complex, the intermediate process control request is strict. And apply theoretical knowledge and professional skills that involve multiple fields and disciplines, all kinds of control valves can be used in multi-step synthesis, separation technology, analysis and testing, performance screening, compounding technology, formulation development, commercial processing and other processes. Application valve type Medium/high pressure straight stroke control valve, on-off ball valve, lined on-off valve, V-notch ball valve, UTO/DTO discharge valves, lined ball valve, and so on.
as one of the main exporters and manufacturers in China since 1998â??, now we expend our product line as below: Butterfly valve, Gate valve, Ball valve, check valve, Globe valve, and pipe fittings; the material with Ductile iron, carbon steel, stainless steel, and alloy; The size from DN50 â?? DN2500; the pressure from PN10-PN64; The annual production is more than 10000 tons;
Model 137-010 consists of Robocon Valve (BALEM 130) and Two Flow Control Valve. This valve is installed at outline of pump to prevent back flow caused by Back Pressure. This valve is slowly opening to prevent sudden opening surges, When a pressure reversal occurs the higher downstream pressure is applied to the cover chamber through the control tube line, and the valve closes drip tight.
BKV BTV Model Pressure Relief Control Valve are hydraulically operated control valves and designed to maintain valve upstream pressure value constant and stable, regardless of flow rate variations. When line pressure is higher than the adjusted pre-set valve pressure level, inlet pressure is kept stable by opening fully the valve. In case of sudden pressure increase, it releases the higher pressure wave in a pressure sensitive manner and in this way, the water system works regularly. When there is no flow in the main valve, it closes by itself as fully tightness. The valves hydrodynamic body is designed for unobstructed flow path and provides excellent and highly effective modulation capacity for high differential
Stop valve Bm stop valve is a kind of manual stop valve, applied to the liquid, air section and heated air in the lines of refrigeration units. Specifications Available with all fluorinate refrigerants. The valve could be fully closed with minimum torque exerted on teflon valve board. The three stainless steel shims can effectively prevent leaking during the entire life cycle of the valve. The hidden valve cover helps prevent moisture penetration. Liquid temperature range:-40~+120f¦; Max. Working pressure: 3.5mpa. Note: kv is the water flux when the pressure decreases to 1 bar and ¬-=1000kg/m3.Unit:m3/h
Ball, butterfly, gate, globe, check, plug , diaphragm & ptfe line valves.
Featuring abrasion resistance,high pressure resistance,erosion resistance and anti-scaling performance,the slurry valve is specially offered for controlling or shutting off the slurry.The slurry valves are widely used at alumina,steel ,metallurgy and mining industry. Features 1.The valve body of y type globe valve for alumina slurry control is consisted of two pieces. The left and right valve bodies are provided in geometric design. Besides the solidworks software for three -dimensional design ,the ANSYS software is also applied for flow field analysis. 2.The valve seat of y type slurry valve is separated from the valve body.The valve seat is installed between the two valve body ,so the valve seat can be replaced easily . 3.To ensure the valve stem has straight line motions ,there is an anti-rotation device provided for the valve stem of the y type slurry valve . 4.Low pressure drop . 5.The range of product is anti-scaling,which are widely use in alumina process. Technical Specifications Size214? DN50~DN350 Pressure Class 150~Class 600 PN1.0~PN16 Body materialWCB, CF8, CF8M, CF3, CF3M etc Connection type :Flange ,weld Driving method:Manual ,Electric,Pneumatic Applications Alumina industry Polymer Industry Chemical industry Steel industry Nonferrous meta l industry
Featuring abrasion resistance,high pressure resistance,erosion resistance and anti-scaling performance,the slurry valve is specially offered for controlling or shutting off the slurry.The slurry valves are widely used at alumina,steel ,metallurgy and mining industry. Features 1.The valve body of y type globe valve for alumina slurry control is consisted of two pieces. The left and right valve bodies are provided in geometric design. Besides the solidworks software for three -dimensional design ,the ANSYS software is also applied for flow field analysis. 2.The valve seat of y type slurry valve is separated from the valve body.The valve seat is installed between the two valve body ,so the valve seat can be replaced easily . 3.To ensure the valve stem has straight line motions ,there is an anti-rotation device provided for the valve stem of the y type slurry valve . 4.Low pressure drop . 5.The range of product is anti-scaling,which are widely use in alumina process. Technical Specifications Size�?214�?? DN50~DN350 Pressure �?Class 150~Class 600 PN1.0~PN16 Body material�?WCB, CF8, CF8M, CF3, CF3M etc Connection type :Flange ,weld Driving method:Manual ,Electric,Pneumatic Applications Alumina industry Polymer Industry Chemical industry Steel industry Nonferrous meta l industry
Industrial valves rubber products, PTFE lined, rubber lined diaphram valves, straight through type kb type & weir type.
Automatic Control Valve, Pressure Relief Valve Model 133-010 consists of Robocon Valve (BALEM130) and Pressure Relief Pilot Valve. It is installed at bypass of the pipe line in order to prevent damage on pipe by discharging high pressured water to atmosphere once the pipe pressure increased higher than the pre-set pressure, and strengthen the maintenance of constant pressure at the inlet pressure within the pre-set pressure. To protect equipment in the pipeline, when pressure raises rapidly, valve will open fast and when valve closes, closes slow to protect surges and can adjust the speed of the opening and closing.
Ball Valves : These are available from +÷ (20mm) to 4÷(110mm) sizes having pressure ratings of 16,10 & 6kg/cm2, with solvent socket type, threaded type & flanged type end connections. The socket ends are as per IS:7834, while threads are as per IS:554/BS:21. These Ball Valves being manufactured in PVC material in lieu of their inherent properties of light weight, corrosion resistance, excellent flow and long maintenance free working life are used as substitutes for Metal Ball Valves in piping systems for housing, industries, commercial complex, etc. Non-return Valves & Foot Valves : These are manufactured in PVC material and are available in sizes +÷ (15mm) to 4÷ (110mm). Non-Return Valves ensure trouble free operation in horizontal as well as vertical installed position in water pipe line. Foot Valves also ensure leak proof operation in suction lines of water pumps. Standard Carton Packing
We manufacture and supply our valuable clients a broad assortment of manual valves & actuated valves. Our range comprises manual ball valve, manual butterfly valve and actuated ball valves & actuated butterfly valves. These valves are manufactured employing high tech machinery and advanced technology under the strict surveillance of our experienced professionals. The valves we offer can be availed in various specifications at competitive prices. Our organization is counted amongst the most distinguished manufacturers and suppliers of finest quality 3 piece design ball valve. These products are manufactured using high grade raw material that is sourced from the registered vendors of the market. Our range is available with a heavy directional lever handle with a great compact design. The floating ball in the valve helps in easy movement of ball with minimum torque. Moreover, the blow out proof stem design ensures maximum safety during high pressure. Three piece design facilitates easy maintenance of ball valve without disturbing the existing pipe line. Apart from this, we offer these to the clients at market leading prices. Ball valves are available in screwed / socket weld & flange ends. Features: •Robust body with strong handle •Low operating torque •Material– ss 316, ss304, cs, with ss working parts •Reliable economical attractive long lasting ball valves.
Balem 441 is a float hydraulic liquid level control valve for use in reservoirs. It is a solenoid operated hydraulic control valve. In case if power failure, it can be overridden mechanically by installing a pilot valve. It is suitable for and safe at high pressure flow as it' s opening and closing is both by solenoid and mechanical pilot valve. It' s corrosion resistance and thermal resistance is excellent, and it will not contaminate the line fluid.
With years of experience in the line of sanitary ball valves, we have established ourselves as one of taiwan's leading brands. Our sincerity and hard work has helped us to match our quality with international standards. We produce best quality ball valves to meet the needs of our valued customers. Sanitary ( hygienic ) ball valves specification comply with 3a mainly, ball valves : 1000 wog (max) , clamp end & weld type , cf8m material . Standard packing.
Square head concentric type AL-bronze slim disc. 2.Package of teflon lined valve A.Standards export package B.Bubble bag,plastic bag C.Wooden case D.All the package material are environment
ZJHP/M-GW pneumatic high temperature control valve consists of a multi-spring pneumatic diaphragm actuator and a low flow resistance high temperature regulator valve body. The multi-spring actuator is low in height, light in weight and easy to install. The valve body runner of pneumatic high temperature control valve is S streamlined, which has the advantages of compact structure, light weight, sensitive action, small pressure drop loss, large valve capacity, accurate flow characteristics and convenient maintenance. It can be used in harsh working conditions. Pneumatic high temperature control valve It is equipped with an electric-gas valve positioning or a pneumatic valve positioner to achieve automatic adjustment control of the fluid medium in the process line. Pneumatic high temperature control valve is widely used in process parameters for precise control of gases, liquids, vapors, etc. For example, it can allow parameters such as pressure, flow, temperature, and liquid level to be maintained at a given value. Pneumatic high temperature control valve is especially suitable for occasions where the leakage is small, the pressure drop of the control valve is small and the temperature is high.