Lime vertical kiln, just like its name, the shape is erect. It is used for calcination limestone. Due to has low energy consumption, less cover area, less investment, wide applicability fuel, and more advantages, it was widely used in metallurgy, construction materials, calcium carbide, Nanometer calcium carbonate, aerated concrete, sugaring, etc. The vertical kiln was manufactured by ZK group with modern new technology, which is an environment protection, save energy, higher machanization and automaticity, quite modern lime kiln. Because it adopts the modern technology, make full use the cheap energy, especially pollution of gas for environment harmful( such as conventer gas, blast furnace gas, calcium carbide furnace tail gas) as the energy, turn waste into wealth. Thus will protect the environment, and produce the high quality lime with lowest cost. To use this new technology enterprise, economic benefits have increased significantly. It should be pointed out that the kiln type especially suitable for the production Nanometer calcium carbonate. Investigate its reason that the concentration of CO2 in flue gas jet can reach more than 35%, CO2 recovery cost is low. Our advantages: 1.Save energy;There are preheating zone, calcination zone, cooling zone from the top to bottom of kiln inside. The cooling air blow into the cooling zone from the bottom, though the heat transfer, the goods were cold, and the cooling air was heated, then put into the calcination zone with the heat for burning, thus reduce the energy consumption. The flue gas from the fuel after calcination enter into the preheating, make the material heat to pre-dissociation temperature. The flue temperature fall to 170-300â??, then come out from the kiln. 2.The shell of kiln use four layer refractory in vertical masonry, good effect of thermal insulation, the temperature of shell will be controlled higher 60â?? than environment, save energy remarkably. 3.Long service life of refractory, the material not directly crash the work surface of refractory, but its fraction with work surface by gravity setting. Thus it greatly reduces the wear rate of refractory, the refractory will be used in 6-10 years in normally. 4.Less cover area, because the vertical kiln in vertical layout, feeding use the single bucket elevator in high angle layout, each functional area is decorated compact, greatly reduces the cover area.
This machine build with UniSmartcut technology of laser cutting and smart digital control system. With this laser cutting machines, the depth of cut can be accurately controlled, making them ideal for creating die cutting boards, usually MDF board for this purpose can be laser cut into any shape to show any design, the max. cutting deepth is 200mm. Features 1. UL-D series equipped with high quality CO2 laser tube, special design optical path processing & transmission system and moving parts driven by DSP digital control system to get high quality processing solution, which will not damage processing material. 2. Due to the stable optical path design, the cutting power will not be effected by optical route distance, this technologies could ensure the same cutting aperture within processing area. 3. Professional laser cutting software, powerful function built-in, friendly human-computer interface, easy operating, it is also suitable for CAD/CAM auto-programming and optimize typeset collocation. 4. Standard industrial computer configuration, high speed analog input and output & digital input and output module. 5. To make sure die board laser cutting machine reliable operation, this machine apply non-oil air compressor, refrigerated air dryer, high precision filter, exhaust fan. Applicable Materials Wood & Plywood & M DF. Above includes materials commonly processed by laser, for questions on other materials please contact an applications specialist. Technical Specification Product Model UL-D Series Laser type CO2 laser, Safety Class 4 Laser Power 300-400W Cutting Area(mm) 1200*1200 Max. working clamp area(mm) 2440X1200 Laser power adjustable 0-100% by manual or automatic (it can be setup in software and hardware) Max. cutting speed 0.8m/min (upon different materials) Cooling Water-cooling Positioning accuracy 0.03mm Data format AI, BMP, PLT, DXF Working voltage AC110/220V±10% Software Unikonex professional software Option Non-oil air compressor, refrigerated air dryer, high precision filter, exhaust fan and etc.
mowerequip.,.com/ Features for the Husqvarna CRT48-33K High blade speeds Offer higher productivity and better finishes. Optimum maneuverability Thanks to its balanced power-to-weight ratio and ergonomic twin lever controls. Smooth automatic operation A special variable clutch offers proper torque and speed range to match concrete conditions without mechanical adjustments. Since the clutch helps to keep constant torque the belt life is prolonged. Good visibility Front and rear lights as standard lets you perform in dim light and during night operations. Specifications Blades: 10 pcs Vibration value, m/s�²: 1.4 m/s�² Engine Motor/engine manufacturer: Kubota Motor/engine model: WG972 Output power (As rated by the engine/motor manufacturer): 31 hp. Power output: 31 hp. Exhaust emissions (CO2 EU V): 939.1 g/kWh
Product Features 1 English and Chinese graphical interface, Windows 7/10 operating system; 2CCD precise positioning, with XY precision platform, optional configuration CO2(UV/FAYB) laser marking system; 3 Marking position accuracy within 0.02mm: 4 Can be engraved Chinese characters, English, numbers, ICONS, serial numbers, logos, Bar code, two-dimensional code and other content; 5 Can access ShopFloor/MES system, support Gerber,DXF and other documents import; 6 Support printing various types of PCB, FPC, metal shield cover and so on The surface of the material; 7 Full visual operation; 8 Flip board function: This parameter is optional.
QR Code PCB Laser Marking Machine PCB-0909 Laser Marking Machine Usage PCB inline QR code laser marking machines are mainly used for automatic engraving QR code on PCB surface (different model according to PCB's size ), available on white oil, green oil, black oil and other inks and copper surface . It can automatically engrave QR code of raw materials procurement, production process, batch, manufacturer, date , and destination for trace ability and management. Feature 1, Imported CO2 laser, fiber laser, green laser, UV laser, stability performance. 2, Imported high speed vibrating mirror, high processing precision and marking speed, stable performance. 3, Easy to use software interface , easy to learn. 4,Automatically obtain the work order, product batch number, material name encoding, specifications and other information and automatic marking. 5, Automatically read and save the QR code, record and alarm if not available. 6, Automatic feeding m achines can be customized. 7,Environmental friendly, less consumables,less pollution, free maintenance compared to ordinary jet printing way. Parametres Item Specifications Name Large Panel PCB Automatic Inline QR Code Laser Engraving System Model PCB-0909 Laser type UV lasers, green laser, fiber laser, CO2 laser optional Marking range 100mm�?100mm(standard lens);Max up to 200mm�?200mm (depending on the type of laser, lens) Marking speed 6000 mm/s (for example: white ink, size 3 �?3mm, contains 45-digit 2D bar code,complete in 1 second,the actual processing efficiency depends on the laser type and laser power) Marking position accuracy ±0.08mm (can be customized according to customer requirements) Applicable PCB size Size is less than 800mm�?800mm; Thickness 0.5mm-10mm (can be customized); Application PCB rigid board white ink, green ink, blue ink and other inks; copper (depending on the type of laser) Power demand 220V/50Hz,total power about 3500W One-dimensional code Code 39, Code 25, Code 93,  Code 128, EAN-13, EAN-8, ISBN,etc. 2D dimension code Datamatrix, QR Code, micro QR Code, PDF417,  Code 49, Code 16K ,etc. QR code size 1.5mm�?1.5mm~10mm�?10mm(depends on the laser type) Character types Supports TrueType fonts, single font (JSF), SHX font, bitmap fonts (DMF) Minimum character height 0.1mm ~0.4mm(depending on the laser type) File format DXF, PLT, Excel, TXT file format Automatic positioning Supports automatic photo, 2, 3, 4 points localization way Automatic read code Read qr code automatically and save data, alarm if can't read Intelligent production Can be connected to ERP/MES/SAP system,  automatic access to the order number, product batch number, material code, commodity information etc. and code automatically Loading Automatically loading system can be customized unloading Automatically unloading system can be customized Turnover device Turnover device can be customized Other automatic system Other automatic system of connection to product line
Being one of the trusted firms in the industry, we are engaged in providing a high quality range of Electronic Water Conditioner. Other Details: Beneficial for hard water treatment, residential, agricultural and commercial purposes, these products are used in water industry Owing to the following list of striking features, our comprehensive array of Electronic Water Conditioners is highly acknowledged in the markets: No salt or chemicals needed No maintenance, no plumbing & easy to install Mains pressure unaffected Retains healthy minerals Little space required and safe Low running cost, negligible power consumption Effective on PVC, HDPE, copper or GI pipe & steel pipe No waste water Money back guarantee Hard Water: Rain water is some what acidic because as it falls through the atmosphere it encounters carbon dioxide (CO2) with which it reacts to from carbonic acid as follows Rain water combines with gases in air & becomes slightly acidic. H2O CO2 = H2CO3: Water carbondioxide = carbonicacid The slightly acidic water dissolves rock and forms hardness The hardness in the water come from the calcium and magnesium salts that dissolved into the water from soluble rocks through which the rain water flows Lime scale is the precipitation of calcium salts, especially in hard water areas causing hard scale to form in pipes, taps, washing machines, shower heads, geysers, solar heaters & boilers Lime scale combines with the soap & makes it lather less It leaves tide marks on baths, sinks, basins, toilets & taps that are difficult to remove Science Research showed that these salts combine with each other to form crystals & attaching themselves to other surface in the form of scale Further research proved that a rapidly changing electronic waveform would neutralise these bonds but that a different wave form was needed for each mineral which should be generated accurately & with controlled speed Features: Fully automatic Easy installation Cost effective
Being one of the trusted firms in the industry, we are engaged in providing a high quality range of Water Softener-Commercial & Agriculture and Electronic Water Conditioner. Other Details: Beneficial for hard water treatment, residential, agricultural and commercial purposes, these products are used in water industry Owing to the following list of striking features, our comprehensive array of Electronic Water Conditioners is highly acknowledged in the markets: No salt or chemicals needed No maintenance, no plumbing & easy to install Mains pressure unaffected Retains healthy minerals Little space required and safe Low running cost, negligible power consumption Effective on PVC, HDPE, copper or GI pipe & steel pipe No waste water Money back guarantee Hard Water: Rain water is some what acidic because as it falls through the atmosphere it encounters carbon dioxide (CO2) with which it reacts to from carbonic acid as follows Rain water combines with gases in air & becomes slightly acidic. H2O CO2 = H2CO3: Water carbondioxide = carbonicacid The slightly acidic water dissolves rock and forms hardness The hardness in the water come from the calcium and magnesium salts that dissolved into the water from soluble rocks through which the rain water flows Lime scale is the precipitation of calcium salts, especially in hard water areas causing hard scale to form in pipes, taps, washing machines, shower heads, geysers, solar heaters & boilers Lime scale combines with the soap & makes it lather less It leaves tide marks on baths, sinks, basins, toilets & taps that are difficult to remove Science Research showed that these salts combine with each other to form crystals & attaching themselves to other surface in the form of scale Further research proved that a rapidly changing electronic waveform would neutralise these bonds but that a different wave form was needed for each mineral which should be generated accurately & with controlled speed
The check valve is a kind of one-way valve, which relies on the pressure of the medium to realize the metal seal between the spool and the valve body, the greater the medium pressure, the better the sealing performance. Product Description The check valve is a kind of one-way valve, which relies on the pressure of the medium to realize the metal seal between the spool and the valve body, the greater the medium pressure, the better the sealing performance. The check valve design and manufacture of APImeivalve fully meet the requirements of API spec 6A and can be used interchangeably with equipment conforming to API spec 6A. The valve body is made of alloy steel forging, with strong mechanical properties, and can withstand high pressure, with safe and reliable performance. The bonnet and valve body are bolted together, and the seal is the sealing ring on the bonnet and the inner wall of the valve body. The sealing performance is reliable. It provides minimal assembly clearance between the bonnet and body (designed to be 0), thereby reducing erosion of bolts and holes by corrosive media and reducing bolt loads. Hard alloy is hard-faced on the core and sealing surface of the valve body so that it has good wear resistance and corrosion resistance. The core material should use sulfur-proof steel, and other parts should use the method of limiting hardness so that the valve can be used in an environment containing H2S. Install the valve body into the pipeline according to the flow direction on the valve body. The valve core by the upper and lower pressure to achieve movement and sealing so that the valve core can not be stuck. Technical Parameters 1. One-way flow of the working medium. 2. Working pressure: 2,000 psi ~ 20,000 psi 3. Nominal diameter: 2.1/16 "~ 4.1/16" (52mm ~ 103mm) 4. Working medium: oil, natural gas, mud, H2S and CO2 gas 5. Operating temperature: -46C ~ 121C (LU level) 6. Material level: AA, BB, CC, DD, EE, FF, HH 7. Specification level: PSL1 ~ 4 8. Performance level: PR1 ~ 2
Wellhead Christmas Tree In oil and gas extraction, oil recovery trees or "trees" are a combination of valves, casing tetrads and fittings used to regulate pipe flow in oil wells, gas wells, water injection wells, water treatment wells, gas injection wells, condensate wells and other types of wells. Product Description Wellhead and Christmas tree equipment is an important equipment of oil and gas drilling, the casing head, tubing head, and oil (gas) tree of three parts, used to connect the casing string and tubing string, and the sealing between the layers of casing and tubing annulus, and can control the production wellhead pressure and adjust the oil (gas) wellhead flow, also can be used in acid fracturing, injection, testing and other special operations. Wellhead devices and trees can be divided into oil production wellhead devices, gas recovery wellhead devices, fracturing and acidification wellhead devices, thermal recovery wellhead devices, and other wellhead devices. The Wellhead devices and tree is mainly assembled by a gate valve, throttle valve, three-way, four-way, plug valve emergency cut-off valve and other pressure components. Working Pressur:2000PSi,3000PSi,5000PSi,10000PSi,15000PSi, Technical Parameters 1. Nominal diameter:2-1/16,2-9/16,3-1/16,4-1/16, 2.Specification level:PSL1,PSL2,PSL3,PSL3G,PSL4 3. Performance levels: PR1, PR2 4. Material level: AA, BB, CC, DD, EE, FF, HH 5. Temperature level: K, L, N, P, S, T, U, V 6. Working Medium: Oil, Natural Gas, Mud and Gas Containing H2S, CO2 7. Execution standard: API 6A, NACE MR0175 8. Main Components: Casing Head, Tubing Head, FC type Gate Valves, Flange, Cross, Choke Valve, Casing Hangers, Tubing Hangers, Pressure Gauges, etc. Wellhead Christmas Tree Features Well Intervention Pressure Relief Chemical injection Tree and well-monitoring points Flow composition and rates Valve and throttle position feedback Connection points
Activated carbon (also known as active carbon or activated charcoal), is an artificial carbonaceous (carbon-rich) material. It is typically made from wood, but also can be made using bamboo, coconut husk, peat, woods, coir, lignite, coal, pitch, and other dense carbon sources. There are a variety of similar substances that fall under the general classification of activated carbon such as activated coal and activated coke, but they all share the properties of vast surface area per mass, exceptional microporosity, and a composition of almost exclusively elemental carbon. The pore structure of activated carbon can be seen with an electron microscope and is primarily responsible for its usefulness. Microscopes show a surface honeycombed with holes and crenelated with ridges which join to a similar structure deeper within the carbon. Due to this structure, a pound of activated carbon, for instance, can have as much as 100 acres of surface area packed into it. These small, low-volume pores allow for increased adsorption capacity (the process of chemical surface bonding, not to be confused with absorption) and allow more reactions between the carbon and other media. Activated carbon is therefore highly valued in filtering, deodorization, medical, and chemical applications, as most contaminants easily bind to it and remain trapped in the carbon microstructure via many small distance-dependent atomic attractions (known as London dispersion forces). Because carbon is produced through a relatively inexpensive and simple series of activation processes, it is widely available for applications; however, activated carbon must be constantly changed as it becomes clogged with contaminants, water, and becomes a breeding ground for dangerous microorganisms after a certain contact time. This means activated carbon is constantly produced to meet the demands of its uses and is kept in large supply to ensure no delay exists in the replacement process. How to Make Activated Carbon The production process of activated carbon, or the activation of carbon, exists in two forms. A carbonaceous source such as wood, coal, peat, or any organic carbonaceous material is carbonized, which means the pure carbon is extracted by a heating method known as pyrolysis. Once the material is carbonized, the material needs to be oxidized or treated with oxygen either by exposure to CO2 or steam or by an acid-base chemical treatment. The sections below will briefly detail these processes.
Product : Bromothymol Blue C.A.S. No. :76-59-5 M.F. : C27H28Br2O5S M.W. : 624.40gm/mole Specifications: Dye Content (by Spectrophotometry) >95% Transition Range pH 5.8-7.6 Yellow-Blue Solubility 0.1% (95% EtOH) Clear solution Absorption maximum (pH 5.8) 1max 430-435nm Absorption maximum (pH 7.6) 2max 615-618nm Absorptivity (A1%/1cm at pH 5.8 at 1max) 260-300 Absorptivity (A1%/1cm at pH 7.6 at 2max) 470-520 Loss On Drying (110C)
In an electrolyzer, why not utilize a carbon-based Gas Diffusion Layer? Using a carbon-based gas diffusion layer (GDL) in an electrolyzer can pose several challenges. The presence of oxygen ions and voltage on the anode side of the electrolyzer can cause the carbon in the GDL to be oxidized, resulting in the generation of CO2 gas. While this can initially lead to a lower electrolysis voltage, the consumption of the carbon GDL is a short-lived phenomenon. As a result, the stack compression decreases, leading to higher resistance and lower performance. Therefore, it is not advisable to use a carbon-based GDL in an electrolyzer. Parameters Place of origin: Baoji, China Brand: TOPTITECH Filtration precision:0.2um-100um Material: titanium Working temperatureï¼?â?¤ 300â?? Length: 30-1000mm(More than 1000mm can be welded) Thickness: â?¥0.5mm FEATURES High corrosion resistance: Titanium is a highly corrosion-resistant material, making it suitable for use in harsh environments. High strength-to-weight ratio: Porous titanium plates are lightweight yet strong, making them ideal for applications where weight is a concern. High porosity: The porous nature of titanium plates allows for efficient diffusion of gases, making them well-suited for use in electrolyzers and fuel cells. Customizable properties: The pore size and distribution of porous titanium plates can be tailored to meet specific application requirements, allowing for greater flexibility in design. Excellent thermal conductivity: Titanium has a high thermal conductivity, which allows for efficient heat transfer and thermal management in fuel cells and electrolyzers. Long service life: Due to its corrosion resistance and durability, porous titanium plates have a long service life, reducing maintenance and replacement costs. Ease of manufacturing: Porous titanium plates can be manufactured using a variety of techniques, including sintering, powder metallurgy, and electrochemical etching, making them easy to produce in large quantities and at a reasonable cost.
Konica KM 1024 MAB Printhead Reduction in the CO2 emissions level of approximately 50% during product usage(Per-nozzle comparison with KM512) The unit is equipped with twice the number of nozzles mounted on the KM512 printhead, enabling the high density required to realize the 72mm print width. This increased width further enhances applicability to printing systems (e.g. Single-pass inkjet printers) that demand high productivity. Printhead power consumption is reduced by 50% through the use of a new, high efficiency piezo actuator. Konica Minolta piezo on-demand inkjet heads are already driven using lower voltages than other inkjet heads and the new actuator used in the KM1024 reduces power consumption even further. DUTA-PRINT is a professional supplier of printer unit, printer and printing parts, ink, membrane, filter, all etc. parts and consumable whole sale and manufacturer located in Jawa Timur, Indonesia. Our business engaged to digital printers, filter, ink, consumables and printing solutions. We have our own tech team that help custom to install, operate the machines, they are fully trained and with up to 10 years experience on digital printers. we provide printing solution advise to solve customer's specific printing need and all repair when it needed the parts to supply. We helped our customer save hundreds and thousands dollars over the last 5 years. Please feel free to contact us if you got any questions you may have to Duta-print com
Having botanical name Cymbopogon flexuosus, Lemongrass Oil offered has its origination in India and comes in pale yellow to radish brown color with a very strong and stimulating characteristic lemon odor. With solubility in alcohol and oils and insolubility in water, it has refractive index of 1.4785 - 1.4890 at 20 C and need to be stored in cool, dry and well ventilated area. Further, the packaging needs to be airtight with due protection provided from sources of ignition, heat and sunlight. With the oil extracted using CO2 extraction process from Cymbopogon citratus of Poaceae family, it is derived from fresh/partly dried leaves and is much in demand for its medicinal properties. Also known by its common names of cymbopogon, Guatemala lemongrass, the oil blends well with coriander, geranium, basil, cedarwood, jasmine, lavender and tea tree and has main oil constituents of geranyl acetate, nerol, myrcene, citronellal, neral, geraniol. The oil is majorly used for rejuvenating the body and relieving it from stress. Further, it also helps in clearing headaches as well as in helping combat nervous exhaustion. The oil also helps in boosting nervous system and assists in quick recovery after illness. It is also an an effective cure for various respiratory infections. Specifications : Botanical Name : Cymbopogon flexuosus Common Method of Extraction : Steam Distillation Parts Used : Grass Note Classification : Base Aroma : Citrus Chemical Composition : The main chemical components of lemongrass oil are myrcene, citronellal, geranyl acetate, nerol, geraniol, neral and traces of limonene and citral
Wellhead and Christmas tree equipment is an important equipment of oil and gas drilling, the casing head, tubing head, and oil (gas) tree of three parts, used to connect the casing string and tubing string, and the sealing between the layers of casing and tubing annulus, and can control the production wellhead pressure and adjust the oil (gas) wellhead flow, also can be used in acid fracturing, injection, testing and other special operations. Wellhead devices and trees can be divided into oil production wellhead devices, gas recovery wellhead devices, fracturing and acidification wellhead devices, thermal recovery wellhead devices, and other wellhead devices. The Wellhead devices and tree is mainly assembled by a gate valve, throttle valve, three-way, four-way, plug valve emergency cut-off valve and other pressure components. Working Pressur:2000PSi,3000PSi,5000PSi,10000PSi,15000PSi, Technical Parameters 1. Nominal diameter:2-1/16,2-9/16,3-1/16,4-1/16, 2.Specification level:PSL1,PSL2,PSL3,PSL3G,PSL4 3. Performance levels: PR1, PR2 4. Material level: AA, BB, CC, DD, EE, FF, HH 5. Temperature level: K, L, N, P, S, T, U, V 6. Working Medium: Oil, Natural Gas, Mud and Gas Containing H2S, CO2 7. Execution standard: API 6A, NACE MR0175 8. Main Components: Casing Head, Tubing Head, FC type Gate Valves, Flange, Cross, Choke Valve, Casing Hangers, Tubing Hangers, Pressure Gauges, etc. Wellhead Christmas Tree features include. Well Intervention Pressure Relief Chemical injection Tree and well-monitoring points Flow composition and rates Valve and throttle position feedback Connection points The more here.
The check valve is a kind of one-way valve, which relies on the pressure of the medium to realize the metal seal between the spool and the valve body, the greater the medium pressure, the better the sealing performance. The check valve design and manufacture of APImeivalve fully meet the requirements of API spec 6A and can be used interchangeably with domestic and foreign equipment conforming to API spec 6A. The valve body is made of alloy steel forging, with strong mechanical properties, and can withstand high pressure, with safe and reliable performance. The bonnet and valve body are bolted together, and the seal is the sealing ring on the bonnet and the inner wall of the valve body. The sealing performance is reliable. It provides minimal assembly clearance between the bonnet and body (designed to be 0), thereby reducing erosion of bolts and holes by corrosive media and reducing bolt loads. Hard alloy is hard-faced on the core and sealing surface of the valve body so that it has good wear resistance and corrosion resistance. The core material should use sulfur-proof steel, and other parts should use the method of limiting hardness so that the valve can be used in an environment containing H2S. Install the valve body into the pipeline according to the flow direction on the valve body. The valve core by the upper and lower pressure to achieve movement and sealing so that the valve core can not be stuck. Technical Parameters 1. One-way flow of the working medium. 2. Working pressure: 2,000 psi 20,000 psi 3. Nominal diameter: 2.1/16 4.1/16 (52mm 103mm) 4. Working medium: oil, natural gas, mud, H2S and CO2 gas 5. Operating temperature: -46 C 121 C (LU level) 6. Material level: AA, BB, CC, DD, EE, FF, HH 7. Specification level: PSL1 4 8.Performance level: PR1 2
Vehicle Emission Monitor Vehicle Emission Monitor is a product designed on the basis of customized sensor technology for variable gases that are emitted from the exhaust of gasoline and diesel vehicles. It is used to measure the concentration of exhaust gases discharged by vehicle engines including CO, CO2, HC, 02, etc. Our company developed the automobile exhaust gas tester in accordance with the national standards of ARAI (AUTOMOTIVE RESEARCH ASSOCIATION OF INDIA). Designed products are divided into automotive exhaust gas testers for transient and steady-state testing of gasoline and diesel vehicles, respectively. APPLICATION AREA Road inspections and random inspections Protection department's transportation department. A quick inspection of the automobile annual inspection test line and Exhaust purification device. Automotive exhausts research in teaching and research units. Automotive manufacturing industry and automotive repair 4S shops. INSTALLATION CONDITIONS Install in a location that meets the following installation conditions. The equipment is properly grounded. There is no strong magnetic field generated by heat sources or electrical appliances near the installation site (such as motors, or transformers) If possible, the equipment is qualified for leak detection. FEATURES : Developed on the Android platform, with good human-computer interaction and intelligent control Rich interfaces, can be connected to oil temperature, speed ambient temperature, humidity, pressure, and other parameters. Instruments designed the best PUC monitor, for Emission control systems in automobiles and are employed to limit the discharge of noxious gases from the internal-combustion engine and other components.
Fiber laser welding machine is an advanced welding technology which is a perfect replacement of traditional electric welding, MIG and CO2 welding. Laser welding process is to melt the connecting area by a very high-energy and dense beam with a large amount of heat. The single module optical fiber laser source provides consistent and stable power and high quality of laser beam. The laser power range can be adjusted according to actual production needs. This solution guarantees unparalleled application flexibility and high reliability.More info pls see our web: www.topteklaser.com ROLLED OVER TRADITIONAL WELDING IN ALL ASPECTS 1.Faster speed: the welding or cleaning efficiency is 5-10 times higher than traditional welding. 2.Easy operation:No need experienced operator, any green hands can operate it within 30 minutes training. 3.Cost-saving: 80% cost-saving than traditional electric welding, MIG welding, argon arc welding. Less operator, less consumption(gas and consumables etc.) and less working time. For example,if the workload equals 1 experienced operators working in 10 hours, but with the laser welding or cleaning machines, only 1 ordinary being can fix it in 3 hours. 4.Welding seam is almost invisible, and smooth welding surface. 5.Very small deformation on Workpiece. 6.Operation safer. 7.Environmental-friendly welding.
Fiber laser welding machine is an advanced welding technology which is a perfect replacement of traditional electric welding, MIG and CO2 welding. Laser welding process is to melt the connecting area by a very high-energy and dense beam with a large amount of heat. The single module optical fiber laser source provides consistent and stable power and high quality of laser beam. The laser power range can be adjusted according to actual production needs. This solution guarantees unparalleled application flexibility and high reliability. ROLLED OVER TRADITIONAL WELDING IN ALL ASPECTS 1.Faster speed: the welding or cleaning efficiency is 5-10 times higher than traditional welding. 2.Easy operation:No need experienced operator, any green hands can operate it within 30 minutes training. 3.Cost-saving: 80% cost-saving than traditional electric welding, MIG welding, argon arc welding. Less operator, less consumption(gas and consumables etc.) and less working time. For example,if the workload equals 1 experienced operators working in 10 hours, but with the laser welding or cleaning machines, only 1 ordinary being can fix it in 3 hours. 4.Welding seam is almost invisible, and smooth welding surface. 5.Very small deformation on Workpiece. 6.Operation safer. 7.Environmental-friendly welding. Technical Parameters Name Portable laser welding machine Welding thickness Carbon steel,Stainless steel (0.5-8mm) Laser Power 1000W/1500W/2000W/3000W Welding seam 0.5mm laser wavelength 1064 NM Voltage AV 220V/380V Laser cable length Standard:8-10� meter, Max:15meters Laser lifetime 100,000 hours Working mode Continuous Working humidity range
Continuous Emission Monitoring System BI7000 Sensor Technology Non Dispersive Infrared Absorption (NDIR), Zirconia (ZrO2), Paramagnetic, Ultraviolet Doppler Optical Absorption Spectroscopy (UV DOAS), Tuneable Diode Laser Spectroscopy (TDLS) Non Dispersive Ultravoilet Absorption (NDUV) Measurement Gas CO : 0-5000 ppm scalable NOx : 0-1000 ppm scalable SO2 : 0-1000 ppm scalable CO2 : 0-20% scalable O2 : 0-30% scalable Cl2 : 0-30 ppm scalable HCl : 0-200 ppm scalable HF : 0-30 ppm scalable H2S : 0-200 ppm scalable HC : 0-5% scalable NH3 : 0-500 ppm scalable Analog Output: 4-20mA analog output Digital Interface RS 485, MODBUS Protocol Relay Output 2 Nos. relay for alarms Power Supply 110/230 VAC, 50 Hz Dimension 19 Rack Heated Sampling Probe Operating temperature : Max. 400 C Mounting : Flange type. 2, 150 rating RF Max. working pressure : 6 bar Voltage : 110-230 V, 50 /60 Hz Heating : Self-regulating 180C For dust concentration : Upto 5 g/m MOC : SS 316 Heated Sample Gas Line Process Tube : PTFE / SS Process Tube Size : 1/4 inch OD Operating Voltage : 230 V AC Max. Operating Temperature : 200 C Sample Conditioning Unit with Industrial Cabinet Aspirator/Pump for sampling flue gas Pre and post cooler fine filters to remove drain, dust and mist in sample gas Auto drain and auto purging (blow back) facilities 2 way solenoid valves for switching, sampling, purging, draining and calibration Flowmeter to regulate and monitor the flow of sample gas Drain pump for continuous removal of condensate Sample Gas Cooler Industrial Cabinet Dimension: 1500 (H) x 600 (W) x 800 (D) mm
