icon ZB045075085-00 side workbench 450*750*850 *1 set worktop 450*750*T *1 piece FSRA02-045083L single drawer single door floor cabinet 450*550*830 *1 pcs accessories ME01006ZE0 five-pin multifunctional power socket 86type 10A250V *2 pcs FXRB02-021010B steel single triangle tank 210*100*100 *1 pcs accessories installation at site FLRA01-0170830 steel side sealed plate 175*830*20 * 2piece
icon ZB100075085-00 side sink workbench 1000*750*850 *1set worktop 1000*750*T *1piece FGRA00-100781W C type side table steel frame 1000*725*810 *1set FSTC24-1000600 steel double door sink suspend cabinet 1000*500*600*1pcs accessories SAN-8101G PP drip rack 401*117*555 *1pcs SAN-21314A three way faucet *1pcs UF000000 water proof plate 1000*100*T *1pcs SAN-5101B PP sink 550*450*310 *1pcs SAN-5300 water drain *1pcs SAN-5301B bottle trap *1pcs SAN-7101 eye washer *1pcs FLRA01-0110750 steel side sealed plate 110*750*20 *2piece
desk type fume hood 1500*850*2330 *1 set desk type fume hood (top cabinet) 1500*850*1500 *1 set worktop 1258*705*20/25 *1 piece inner embedded door storage cabinet (bottom cabinet) 750*500*830 *2 pcs accessories wall type water supply faucet 1set wall type gas supply faucet 1 set five hole socket 220V 4 pcs cup sink 1 set inner embedded door bottom cabinet layer plate 745*440*18 2 piece fume hood bottom cabinet side sealed plate 285*830*18 2 piece
S&A air cooled chiller CW-5000 for chemical and laboratory S&A brand CW-5000 chiller developed and produced by S&A company of China, it is applied to cool chemical and laboratory equipment. Since January 2016, the warranty period of S&A chiller has extended to 2 years. S&A chiller CW-5000 features 1. 800W cooling capacity; use environmental refrigerant; 2. Compact size, long working life and simple operation; 3. ±0.3? precisely temperature control; 4. The intelligent temperature controller has 2 control modes, applicable to different applied occasions; with various setting and display functions; 5. Multiple alarm functions: compressor time-delay protection, compressor overcurrent protection, water flow alarm and over high / low temperature alarm; 6. Multiple power specifications; CE,RoHS and REACH approval; Chiller parameter: Model CW-5000AG CW-5000BG CW-5000DG CW-5000AH CW-5000BH CW-5000DH CW-5000AI CW-5000BI CW-5000DI Voltage 220V 220V 110V 220V 220V 110V 220V 220V 110V Frequency 50Hz 60Hz 60Hz 50Hz 60Hz 60Hz 50Hz 60Hz 60Hz Current 1.4~2.1A 3.5~5.6A 1~4.8A 3.5~5.6A 1.4~2.1A 3.5~5.6A Compressor power 0.295KW 0.38KW 0.305KW 0.295KW 0.38KW 0.305KW 0.295KW 0.38KW 0.305KW 0.40HP 0.52HP 0.41HP 0.40HP 0.52HP 0.41HP 0.40HP 0.52HP 0.41HP Refrigeration capacity 2361Btu/h 2999Btu/h 2866Btu/h 2361Btu/h 2999Btu/h 2866Btu/h 2361Btu/h 2999Btu/h 2866Btu/h 0.692KW 0.879KW 0.84KW 0.692KW 0.879KW 0.84KW 0.692KW 0.879KW 0.84KW 595Kcal/h 756Kcal/h 722Kcal/h 595Kcal/h 756Kcal/h 722Kcal/h 595Kcal/h 756Kcal/h 722Kcal/h Refrigerant R-134a Refrigerant charge 300g 320g 280g 300g 320g 280g 300g 320g 280g Precision ±0.3? Reducer Capillary Protection Overcurrent protection for compressor, flow alarm, over temperature alarm Pump power 0.03KW 0.051KW 0.1KW Tank capacity 6L Inlet and outlet External F10mm brass connector F10mm speedy connector Max. lift 10 M 12M 25M Max. flow 10 L/min 13L/min 16 L/min N.W 24 Kgs G.W 27 Kgs Dimension 58 x 29 x 47 cm (L x W x H) Package dimension 70 x 43 x 58 cm (L x W x H) Note: other electric sources can be customized; heating and higher temperature control precision functions are optiona . Email:marketing@teyu.com.cn; Website: http://www.teyuchiller.com About S&A Brand S&A produces more than 60000 units of industrial chillers by year,we always insist on”Quality First” in design and production. “S&A” and “TEYU” have been enjoying high reputation among hundreds of manufacturers which are from both at home and abroad,and export rate reaches above 60% -
We manufacture laboratory Glassware and export it all over the world. e.g. Test Tubes, Beakers, Flasks, Cylinders and many more Standard lot size is in No.s
1 Frame Steel structure 2Table topMade of 12.7mm thick corrosion-resistant black c-spc , one door one drawer 3 Cabinet Use high quality cold-rolled steel sheet, the surface is parkerised by acid and electrostatic sprayed by epoxy resin powder. Color can be chosen according to color-disc 4 Slideway Three section slide rail , no noise 5 Hinges Pen type high quality hinges 6Handle Stainless steel bright type handle Advantages: Steel structure lab furniture are elegant-looking , color-rich, economy and durability and so on. Our products have various sizes and styles giving you a modern lab space. Our products have passed the iso9001 Our price will be satisfactory and our quality will be the same as or even beyond your request. We will design the customized products for you. Product pictures for reference:
39- liters laboratory flotation machine is applied in ore dressing by the method of laboratory floating. It is concatenation floatation machine with several sets of machines. And the number of chutes is even from 1 to 10. It is left-type or right-type according to user's demand. Structure and features: Laboratory flotation machine with 39 liters is impeller mechanical flotation machine. It is composed by the following main parts: (1). Tank The tank 1 is welded with steel plate, using the impeller to stir, simultaneously inflating the air into pulp. In order to adjust the thickness of slurry surface in tank and foam layer scraped, the intermediate tank 15 is made up of two slot panels, in which is the pulp surface regulator 5 installed, orifice 17 is installed on the tank cover 14, which is used to prevent the chaotic movement of pulp affects on the bubble zone, the gangue is entrained mechanically to the concentrate. Basin liner 6 is equipped in the tank to prevent the tank bottom worn, basin liner can be replaced. Discharging port 8 is placed outside the tank bottom, which is used to storage water when cleaning. The pulp flows into the intermediate tank 15 and the end tank 3 from the overflow port on the panel, the catheters of the intermediate tank bottom and the cover 14 on the groove wall bottom are put into the next tank, which will flow continuously through all the tanks of flotation machine. The pulp is fed from the feed chute 3, is discharged from the discharging port 8 of the tailing 1, the feed port 16 is equipped in front and at the back of tank bottom, which is easy to change the technological process. (2)Impeller system Impeller system is installed in the center of the flotation tank, the vertical arrangement coiled impeller 9 which leaves are up is fixed at the bottom of the impeller shaft 10 and around the vertical shaft tube 12. The tube top is located over the pulp stone and foam layer, the tube bottom is bearing the cover 14. When the impeller rotates, the quantities of air can be absorbed along the vertical tube 12. The protective plate 4 is fixed under the cover 14, the gap between the protective plate and impeller is related to the aeration rate, its maximum gap is less than 3mm, if the gap is too large, it is necessary to replace the protective plate or be adjusted appropriately. The hole of vertical tube 12 is used to cycle pulp, and make the pulp and air mix well. The upper of the impeller shaft rotates in the rolling shaft 11 installed in the bearing shell, the bearing shell is installed on the beam 7. The pulley fixed at the top of the shaft makes the motor 18 rotating through the triangle belt, of which the tension can be adjusted by the nut 19. (3). Shaving foam device Foam is scraped using the rotary scraper along the flotation machine, scraper 20 is installed out of the discharging port. The pulley is installed at the end of the scraper shaft, which rotates through the driving of the worm reducer 21 and V-belt. Technical parameters (1)Tank size: L¡ÁW¡ÁH 315¡Á315mm¡Á527mm (2)The effective volume: 39 liters (3)The flow of the pulp is calculated according to the production capacity (4)Aeration rate: 35-45 liters / min (5)Impeller diameter:200mm (6)Impeller speed: 809m/s (7)Impeller circumferential speed:8.14m/s (8)Scraper rpm: big wheel/small wheel 21r/min /13r/min (9)Motor: Model y900l-4 voltage :220/380V. Power:1.5KW rpm: 1400 r / min (10)Assembly method: Left-style (11)The outline size of machine: H: 930mm, W: 762mm, L (including 2 slots)1081mm (12)Total weight:(including 2 slot motors).
Jacketed glass reactor is an ideal instrument for pharmacy, biology, fine chemistry and material synthesis. With menstruum in inlayer and heating or cooling source in interlayer, jacket glass reactor can perform synthesis, distillation, separation and reflux under airproof condition. Now we can supply you jacketed glass reactor from 1-100L. Function: Putting reaction solvent into jacketed layer of glass reactor to do stirring reaction, the jacketed layer can do constant temperature, heating and cooling reaction to use cooling or heating liquid. According requirements in atmospheric pressure or negative pressure mixing reaction, and can do backflow of reaction solution with distillation. Model : TFD-50L Capacity : 50L Power: 370W Rotating Speed : 100-1400rpm Mixing Torque 1300r/min :22000g.cm Glass Kettle Cover : 60#40#/50#/29# Glass Material: Borosilicate (Pyrex: G3.3) Frame Material: Stainless Steel Mouth Amount of Vessle Lid: 4 Vaccum Degree: 0.095Mpa Machine Size(cm): 100*105*240 Can be customized as requested. Wooden cases.
Introduction Features: 1. Dot matrix lcd display, clear and comprehensive. 2. This device adopts fujitsu mcu as control unit, which is reliable, high accuracy data collect, allows internet access for upgrade and sharing information by serial port. 3. Comfortable using and easy monitoring. 4. Stainless body, easy to clean and highly safety. 5. High efficient water and gas waste disposed by microcirculation. 6. Water proof and heat isolation layers are made of aerial material, high temperature resistance. The entire device can be put inside biosafety cabinet, clean bench etc. 7. Auto lock when temperature reaches 45íµ, protect user. 8. Automatically check of waste bin lock and door lock. 9. Internal cavity sealed by pyrocotton, well heat insulation. 10. Press door/release button to unlock the door after 5seconds. 11. This device is an on spot medical waste disposal system, which can be used to all infectious medical waste, body parts, radioactive and specific chemical waste. The final outcome can be treated as normal waste. Technical parameters: Power supply ac220vía20v Dimension 360*260*230(mm) Weight 15kg Working temperature above 170íµ Disposing duration above 170íµ for 1.5 hours Working capacity 0.6l Circulation time 2.5hours
Laboratory instruments, quality control instruments, precision mechanical components, microscopes, hot air ovens, diffusion cell apparatus, borosilicate laboratory glassware.
Disintegration Test Apparatus
Dissolution Test Apparatus
Disintegration Test Apparatus
Leak Test Apparatus
Melting Point Apparatus
Dissolution Test Apparatus
Leak Test Apparatus
Melting-boiling Point Apparatus
Melting Point Apparatus
Sugar, wheat flour, wheat, sesame seeds, palm oil, rice, brown sugar, white sugar, jute gunny bags, potassium sulfate, urea, ginger, white sugar, nitric acid, hydrochloric acid, sulfuric acid, acetic acid, acids, butyric acid, citric acid, formic acid, perchloric acid, chloric acid, phosphoric acid.Manufacturer and export
