Specification Details: 1) Gr. 4130 Chemical Component Analysis(%): C: 0.28-0.33; Mn: 0.40-0.60; Si: 0.15-0.35; S: < 0.040; P: < 0.040; Cr: 0.80 -1.10; Mo: 0.15-0.25; 2) Monthly Capacity: 6000 tons. 3) 4130 SR Condition's Mechanical Properties: Ultimate Strength: > 724Mpa; Yield Strength: > 586Mpa; Elongation: > 10%; Rockwell Hardness B Scale: 95; 4) Delivery Condition: Annealed(A), Bright Annealing, Normalized(N), Stress Relie f Or Finish Anneal(SR), Quenched and Tempered(Q+T), etc; 5) Surface treatment: ASTM A519-Temporary Coating, Special Coating, Galvanized, immersion oil, lacquer, passivation, phosphating, etc; Or Oil-DIP paint black with two plastic caps on each end 6) Inspection: Strictly according to the standard requirements and offer the original MTC (EN10204.3.1/3.1B) 7) Relevant Test: ASTM 519-Chemical Component Analysis, Mechanical Properties(Ultimate tensile strength, Yield Strength, Elongation), Technics Properties(Flattening Test, Flaring Test, Bending Test, Hardness Test, Blow Test, etc), Exterior Size Inspection, Nondestructive electric Test, Hydrostatic Test, magnetic particle testing; 8) Marking: All tubes are eddy current tested and are marked with size, cast number and specification. Or as per customer's requirement; 9) Packing: Hexagonal bundles with several steel strips, Wrapped in waterproof paper, PVC sleeve, and sackcloth with several steel strips or packed in heavy tri-wall boxes, wooden boxes, wooden slats as requires; 10) Packing Type: Round, Square, Rectangle, Hexagon. Streamline, etc; 12) Applications: Automobile Industry, Mechanical & Engineering, Fluid Power, etc. 13) Place of origin: China 14) whatsapp: 0086 13812877559 15) e-mail: tubesolution at sina.com Commercial Information: 1) Delicery time: (45-60) days ready at mil also according to the actual weightl; 2) Minium order: 5 Ton; (some specification are excepted) 3) Term of payment: T/T or L/C; 4) Delivery Port: Shanghai Port; 5) Offer Validity: 5-7 Days; 6) Container: 20GP or 40GP or Bulk; 7) Manufacture methods: Cold Finished method or hot finished Method.
Microwave heating equipment is used in fast food, chemical rubber, minerals, pebbles and other products that require rapid heating. The microwave heating equipment uses electric energy as an energy source, and uses a magnetron to convert electrical energy into microwaves, and directly performs non-contact heating on the materials. Feature: Compared with traditional equipment, microwave heating has the following characteristics: 1 high efficiency, low energy consumption, 2 uniform heating, 3 fast drying speed, 4 no thermal inertia, instant opening and stopping, 5 safety and environmental protection, 6 operation Simple, easy to control and so on. Feature: Drying: The microwave dryer is used to dry green tea leaf in a short time. Sterilization: The fungus, mycetes and others can be killed by the microwave dryer during the drying process. Fast and evenly: The microwave dryer can change to be heat within several seconds,so the equipment is very efficent. keeping fresh: The sterilization is with lower temp, so the color,taste and nutrition of the tea can be protected well. Safe: The microwave is passing in the metal covered rooms and waveguide without leaking. It will not generate extra heat and pollution. Simple to operate: The PLC system is simple, stable, safe and friendly,so it is convenient to use. Packing and shipping 1. Daub coal oil on the surface of the machines. 2. Plastic film as the inner packing. 3.Train, ship or depend on clients' requirement Our services 1). Free consultation service before, during, and after sales. 2). Free project planning and design services upon clients' special demands. 3). Debugging and inspecting of equipment until everything is functional before leaving the factory. 4). Overseas installation and training of equipment maintenance and operating personally. Company Information: Shandong Joyang Machinery Co., Ltd.is a professional supplier of food processing machines. We are located in Jinan, the capital of Shandong Province. Our company is full of staff with many years of experience in supplying the food process machines. Our company main products include microwave drying machine, microwave sterilizing machine,microwave heating machine, microwave extraction machine,microwave synthesis machine,microwave extracting machine,microwave thawing machine,microwave sintering machine etc. Our professional engineers will supply the most suitable solution to different customers to meet your various demands.Not only in the domestic market,products are exported to India,Russia,Turkey and other places.
Expanded aluminum metal ceiling Expanded Metal Wire Mesh Rigidity Expanded Metal Mesh Feature Expanded metal premise free flow of light, heat, sound and air. Effective alternative cost. Available in a variety of mesh configurations including diamond, square, round, hexagonalplus architectural and decorative patterns It is easily fabricated, finished, installed and formed. Specification Material Aluminum Surface treatment hot-dip galvanizing, electric galvanizing, powder coated, PVC coated, anti-rust paint, polished, anodized, etc. Expanded mesh types Mesh type and direction, limitless choice of colours and lighting designs can be combined with ease to ensure an aesthetic finish. Mesh size and alignement may present a different appearance to the ceiling. Such openings in the ceiling in projects with low ceiling height, ensure that air behind the ceiling becomes part of the general air circulation. Changes in the direction of the meshe cause the formation of different angles of light and fields of vision which, when combined with appropriate lighting systems, create a varitey of aesthetically pleasing shadow effects.Raised expanded metal is also known as standard expanded metal. Raised expanded metal is made by shearing� and stretching the metal sheet with a set of die on a press, creating diamond shaped openings. The solid intersections of two strands are called bonds that lie on top of each other to form a raised effect. This adds additional strength and rigidity to the expanded metal, also provides directional skid-resistance surface. No material is lost in the manufacturing process, not like the perforated metal production, so it is a green engineered alternative in many projects. Feature Can never be unraveled. High tensile strength. Perfect finish. Slip resistance or slip-proof. It provides a screening effect, allowing light, sound, air and water to pass through. A variety of patterns, sizes and colors available, ideal for decorative meshes. Great versatility, stability. Application Flattened expanded metal for ceiling Flattened expanded metal is expanded in its normal way, which is the same as raised expanded metal. An� additional process is by passing raised expanded metal through a cold rolled reducing mill and a leveler, leaving a flat also smooth surface similar to perforated metal. The rolling process elongates about 5% the length of the sheet while the width remains the same. Flattened expanded metal possesses many properties, making it a very versatile product suitable for applications across many industries, such as commercial, automobile and agricultural. Feature �?�Smooth surface won't hurt anyone. �?�Wear resistance. �?�Easy to install. �?�Low cost and free maintenance. �?�Wide range of applications. Application Packaging&Shipping � Packaging: Plastic film then pallet or according to the customer's requirments. Shipping: 15days for 1X20ft container,20days for 1X40HQ container.
Metal Stamping Filter End Caps Metal End Cap Metal stamping of thick or heavy gauge material is not a problem for DongJie Industries. We have presses with higher tonnage capabilities to ensure accuracy, and we offer competitive pricing on all of our metal stamping services.Stamping is an economical way to form metal components with a variety of characteristics including strength, durability, and wear resistance. Stamped parts will also have good conductive properties and stability.At DongJie Stamping, we offer high quality, precision metal stamping for parts and components in many industries. We believe that our levels of engineering, metal stamped part production and overall performance is an art form. Through the decades we�??ve taken advantage of promising technology and applied it uniquely to our advanced systems of getting things done right the first time.DongJie Stamping works with a complete range of materials to satisfy even the most demanding specifications. We service a wide range of industries with a complete array of materials from stainless to plastics. Our equ ipment is capable of handling a wide variety of thicknesses and finishes. We offer complete tractability and documentation when needed. Our ISO 9001:2008 certification gives our customers peace of mind that they are getting the best materials possible for their project.From selecting the best material to tooling for your metal stamping project, we know how to listen and how to hook up our engineering muscle with our customers�?? needs. We�??ve learned how to provide a level of satisfaction that breeds dependability, confidence and value that makes our customers feel powerful. We have the expertise to ensure that your part will be manufactured to your exact specifications and to the highest quality standards. Item Name High Precision Metal Stamping Quality Assurance ISO 9001:2008 stamping parts metal stamping stamped parts Machine Equipment Laser cutting machine, CNC shearing machine, Flat bed spot-welder, Die grinder, Steel processing machine, Double servo turret-type punch press, Banding machine, etc. Material High carbon steel, Mid carbon steel, Low carbon steel, Cold roll steel, Hot roll steel, Zinc plate, Stainless steel, Aluminium, SECC, SGCC, SPCC, SPHC, other material Surface Treatment Blacking, Polishing, Plating Zinc, Plating Chrome, Plating nickel, etc Service OEM/ODM/Customized/Design
Expanded Metal Mesh Expanded Metal Wire Mesh Rigidity Expanded Metal Mesh Expanded metal mesh is an intermediate raw material that allows light and air to flow freely through it and that has more rigidity than the sheet from which it was produced. Introduction of Expanded Metal Mesh Expanded metal mesh is an intermediate raw material that allows light and air to flow freely through it and that has more rigidity than the sheet from which it was produced. It is formed in an expanded metal mesh press and produced from any malleable metal sheet product. The plate, sheet, or coil is simultaneously slit and stretched into diamond-shaped openings. These openings are of uniform size and regularity. Expanded Metal Mesh Basic Types inch inch inch 1 inch Material Suitable for Expanding Carbon Steel, Aluminum, Stainless Steel, Galvanized, Copper, Brass, Titanium, Platinum, Zinc, Nickel, Silver, Gold Surface Finishes hot-dip, galvanizing, pre-galvanizing, anodizing, enameling, power coating, painting, plastic coating, etc Benefits The Flow of Light and Air Design Customization Design Flexibility Strength and Formability Applications Ceilings and roofs, Decorative dividers, Guards, Air and fluid filters, Fencing, Battery cells, Strainers, Partitions, Outdoor furniture, Speaker grills, Security walls, ceilings, floors, doors, Machine and window guards, Shelving and racks, Containers, Greenhouse benches Styles of Expanded Metal Mesh Regular (standard or raised) all expanded metal mesh is produced in regular form off the expanders. The strands and bonds are set at a uniform angle to the plane of the sheet. This gives added strength and rigidity, as well as a skid resistant surface. Flattened is manufactured by processing regular expanded metal mesh in a rolling mill. The rolling process reduces the thickness of the original base metal. Design Designations Strands The sides of the expanded metal meshdesign v Strand Thickness Thickness of the base material from which the sheet was produced. Strand Width Amount of metal fed under dies to produce one strand v Strand Thickness and Width Can be varied to create different openings. The width of the strand should equal or exceed the thickness of the base metal. SWD Nominal dimension, Short Way of Diamond v LWD Nominal dimension, Long Way of Diamond v Design Size Actual dimension SWD and LWD. Measured from a point to a corresponding point on the adjacent diamond. v SWO Short Way of Opening v LWO Long Way of Opening v Bond Where two strands intersect Applications Air and fluid filters EMI/RFI shielding Battery cells Ventilation systems Strainers Satellite and radar antennas Partitions Outdoor furniture Speaker grills Security walls, ceilings, floors, doors Machine and window guards Fencing
Description Introduction of Expanded Metal Mesh Expanded metal mesh is an intermediate raw material that allows light and air to flow freely through it and that has more rigidity than the sheet from which it was produced. It is formed in an expanded metal mesh press and produced from any malleable metal sheet product. The plate, sheet, or coil is simultaneously slit and stretched into diamond-shaped openings. These openings are of uniform size and regularity. Expanded Metal Mesh Material Suitable for Ex pandingCarbon Steel, Aluminum, Stainless Steel, Galvanized, Copper, Brass, Titanium, Platinum, Zinc, Nickel, Silver, Gold Surface Finisheshot-dip, galvanizing, pre-galvanizing, anodizing, enameling, power coating, painting, plastic coating, etc BenefitsThe "Flow" of Light and Air Design Customization Design Flexibility Strength and Formability ApplicationsCeilings and roofs, Decorative dividers, Guards, Air and fluid filters, Fencing, Battery cells, Strainers, Partitions, Outdoor furniture, Speaker grills, Security walls, ceilings, floors, doors, Machine and window guards, Shelving and racks, Containers, Greenhouse benches Styles of Expanded Metal Mesh Regular (standard or raised) - all expanded metal mesh is produced in regular form off the expanders. The strands and bonds are set at a uniform angle to the plane of the sheet. This gives added strength and rigidity, as well as a skid resistant surface. Flattened - is manufactured by processing regular expanded metal mesh in a rolling mill. The rolling process reduces the thickness of the original base metal. Design Designations Strands - The sides of the expanded metal meshdesign v Strand Thickness - Thickness of the base material from which the sheet was produced. Strand Width -Amount of metal fed under dies to produce one strand v Strand Thickness and Width - Can be varied to create different openings. The width of the strand should equal or exceed the thickness of the base metal. SWD - Nominal dimension, Short Way of Diamond v LWD - Nominal dimension, Long Way of Diamond v Design Size - Actual dimension SWD and LWD. Measured from a point to a corresponding point on the adjacent diamond. v SWO - Short Way of Opening v LWO - Long Way of Opening v Bond - Where two strands intersect Price Delivery Port : Tianjin Packaging & Delivery Delivery Lead Time : 15 days
The Product Parameter of the Cosmetic Canvas Makeup BagSupply Cosmetic Canvas Makeup BagItemCosmetic Canvas Makeup BagDimension21.5 X 16 CMFabricCanvas and cottonMin of Order1000PCSOEM ODMAcceptableDelivery Time10-30 days after get the depositPayment TermsTT, Western Union, Paypal, Moneygram or other waysPackagingBy Plastic bag or customized design packagingCertificateWe can do it when you needPicture Show of Cosmetic Canvas Makeup BagQuality Control of Cosmetic Canvas Makeup Bag 3 product-lines + more than 100 workers+strict quality control +dust-free workshop Our factory has been assessed by Bureau Veritas. High-quality as our business objective is winning our long-term customer's trust and support. Welcome to visit our factory and cooperate with us.Company Brief of Cosmetic Canvas Makeup Bag Shenzhen Chart Mate Handbag Limited is a professional manufacturer, providing waist bag, wallet, backpacks, canvas bag, cosmetic bag, cooler bag, bottle bag and others since 2009, covers an area of 8600 square meters. Factory has many years overseas marking experience, especially in Japan market Choose Chart Mate, Choose success.Our advantage 1. 100% manufacturer, â??inspected onsite byâ??Bureau Veritas and Alibaba 2. 20 years engage in bags and gifts business field especially in Japan Market. 3. Adopt high quality material. There is a full set of material inspection process and equipment. 4. Skillful workmanship with advanced machine makes out high quality product and low cost. 5. OEM and ODM orders are highly welcome! 6. Strict Quality Control Raw Material Quality, Product Quality, Final Packaging Control. 7. Delivery On time. Everything is for clients. 8. We built Dust-Free Workshop as per clients' requirementOur Service Top quality; Competitive price; Fast shipping; Drop combined order shipping available; Best and Timely service; 100% satisfaction! 1) We are supplier from Shenzhen of china, 2) You can place order or wholesale them for resale, we can shipping out them to your appointed address. 3) Any question, please feel free to contact with us timely, we will reply within 24 hours. 4) we have so many traders, they are from worldwide, We are glad to do our best for you the best quality and best servings. 5) As a professional supplier with good reputation and long time experience, we can supply various Novelty gifts, Promotion gifts, AD gifts, Business gifts, fashion small commodities etc. According to your requirement.
USE: This machine is suitable for printing such packing materials as polyethylene,Website:http://www.xh-mach.com, polyethylene plastic bag glass paper and roll paper etc. And it is a kind of ideal printing equipment for producing paper packing bag for food, supermarket handbag, vest bag and clothes bag, etc. SUITABLE MATERIAL:Kraft paper:40-350 g/, single-sided coated paper:30-350g/, copy paper:15-350g/, firecrackers and paper:40-350g/, paper money and incense:25-350g/, silicone paper:50-350g/, coated paper:30-350g/, dust-free paper:25-350g/, Release paper:40-350g/, composite paper:30-350g/,thermal sensitive paper:30-150g/Woven:15-120g/, Weave fabric:15-500g/ ,No woven:15-150g/PVC:10-120g/, OPP:10-120g/, PE:10-120g/, PET:10-120g/, CPP:10-120g/ Main parameter:Technical SpecificationModelYTB-6800YTB-61000YTB-61200Color6 color6 color6 colorMaterial feeding width800mm1000mm1200mmMax Printing Width760mm960mm1160mmStructure typeStack typeMaterialNon-woven fabric, Paper, Film(PVC.PE.BOPP.PE), Aluminum foil,PP woven and so onThickness of plate2.28 or 1.7mm (customized by client)Printing length280-1000mm (customized by client)Printing speed100m/minTransmission drive typeSynchronous beltFeeding material part:1.Single unwinder system or double unwinder system, pneumatic loading&unloading system2.Automatic stop machine when break the material; When machine stop, keep tension and avoid the material loose or line deflection.3.Air shaft4.EPC (edge position control): With manually/automatically/ central return function, can adjust the rewind move left and right .5.Automatic tension control system with magnetic brake. Printing sections: 1.print material: resin plate or rubber plate2.Transmission between printing roller and anilox roller:gears3.adjustment method: By Manual (Automatic printing after adjust by manual, when start machine, no need register color again, the printing pressure and register all keep the same.)4.Printing roller lifting system: Automatic Hydraulic cylinder control roll up and down. Drying system: 1.The machine is equipped with blower and heater; and the heater employed central temperature control system2.Dry apparatus between each color, and one more dry apparatus after printing finished Rewinding Part 1.Single or double rewinder system, surface rewinding system special for paper and PP woven.2.Hydraulic loading&unloading system3.Air shaft
Product DescriptionOEM No.: 8D0412131FWeight: 75gLength: 85mmOuter diameter: Ï?59mmInner diameter: Ï?20mmFitting Position: Front Axle. Left and rightSuspension: for vehicles without sports suspension. for vehicles without off-road suspensionWeight [kg]: 0.1 kgRequired quantity: 2Material Type: PUColor: YellowCompatible With Vehicle Brands/Model: For AUDI A4 /SKODA / VOLKSWAGEN/ PASSAT / VW (SVW)External Testing Certification:ISO9001 This Suspension Rubber Buffer Front Axle Fits(fits years) : Model: note1997-2006: A4: 1.81997-2005: A4 Quattro: 1.82005-2008: A4: 2.02009-2009: A4: 2.0: Cabriolet2005-2008: A4 Quattro: 2.02009-2009: A4 Quattro: 2.0 Cabriolet1996-2002: A4: 2.81996-2002: A4 Quattro: 2.82005-2008: A4 Quattro: 3.22009-2009: A4: 3.2 Cabriolet2005-2007: A4 Quattro: 3.2 2000-2005: A6: 2.7 Quattro1998-2001: A6: 2.8 from Ch#4B-W-0000011998-2001: A6 Quattro: 2.8 from Ch#4B-W-0000012002-2004: A6: 3.02002-2005: A6 Quattro: 3.02005-2008: A6 Quattro: 3.22000-2008: A6 Quattro: 4.22000-2006: A8 Quattro: 4.2 2000-2002: S42001-2003: S8 Quattro 2001-2005: Passat: 1.8 awd1998-2005: Passat: 1.81999-2005: Passat: 2.8 4m1992-1994: Passat: 2.82001-2005: Passat: 4.0 awd Performance Characteristics of Suspension Rubber Buffer Front Axle1. Wide range of hardness: It still has the elongation and resilience of rubber under high hardness. Polyurethane elastomer hardness range is Shaw A10-90.2. High strength: Their tear strength and load carrying capacity are much higher than that of general rubber at rubber hardness. Its impact strength and bending strength are much higher than plastics at high hardness.3. Wear resistance: Its wear resistance is very good, generally in the range of 0.01-0.10(cm3)/1.61km, about 3-5 times that of rubber.4. Oil resistance: Polyurethane elastomer is a highly polar polymer compound with low affinity for non-polar mineral oils, and it is hardly eroded in fuel oils and mechanical oils.5. Good resistance to oxygen and ozone.6. Excellent vibration absorption performance, can do vibration reduction and buffering. In the mold manufacturing industry, it replaces rubber and springs.7. Has good resistance to high and low temperature performance.8. Strong radiation resistance: The polyurethane has good performance in resisting high-energy radiation and still has satisfactory performance under 10-10 Ge radiation dose.9. Has good machining performance (car, milling, grinding, drilling can be). Packaging & Shipping
TEMP WELDED FENCING IS MOBILE, REUSABLE, TENANTABLE & EASY TO ASSEMBLE A drawing picture of Canada temporary fence. CAF-01: Canada temporary fence Canada style temporary welded fence, also know as mobile fence, portable fence, is a kind of very popular temporary fencing in Canada and North America. The key feature of Canada mobile fence is the solid frame welded by square pipes, platy stable fencing feet and p shaped top coupler. Temporary fencing is a modular and steady system for isolation & protection work of construction sites, accidents scene, municipal engineering, commercial area, residential use. Regression, if you are a temporary fencing rental company, here is the one-stop choice for your requirement of durable and reusable. WHY CHOOSE US? 360° full welding by hand for highest strength. We own welding technicians all have more than ten years experience. The infill mesh and square pipe frame are welded smoothly and sturdily in 360° to prevent cracks and corrosion. Smooth surface and no burrs. All the weld pots are treated to eliminate all burrs on the surface to ensure the safe set up and tear down. Strong corrosion surface treatment. Electric galvanized before powder coated, the multi-layer anticorrosive treatment can effectively prevent the corrosion of acid rain and ultraviolet radiation. Hot dipped galvanized after welding, to ensure at least 70 μm thickness of zinc coating. Service life can reach more than ten years. Various colors are available. We can provide variety of colours by PVC coated surface treatment. Such as red, yellow, blue, gray, black, green, etc. One-stop supply system. Expect for fence panels, platy stable fencing feet, p shaped top coupler, foot screw (as needed) and shade clothes, other you wanted hardware can be supplied. Reliable and professional advice. As a company integrating production and sales, weâ??d like to give our customers a friendly and reliable advice for picking up the most suitable one for your desired application. Customized size for your needs. We have a standard size temporary fencing inventory. Beside, we accept customized orders of special panel length and height along with the pipe thickness and diameter. Free value-added service. Each container will be equipped with extra 20 clamps and 5 plastic bases for replacement.
Three roller embossing machine Introduction:This machine is used to emboss pattern and trademarks, press bubble on various fabrics (mainly embossing of lining), It can also be used for super ginning, one sided pattern embossing in paper industry, and pattern embossing for wall paper, wall cloth, films, aluminum foil, aluminum plate and plastics etc. in light industry.Technical parameter:No.ItemContentRemarks1TypeThree rollers verticalThe upper and down are wool rollers. The middle is the metal flower roller2Fabric Width1800mm3Speed5-70M/MIN4Way of Changing SpeedInverter5Power of Main Electronic Motor18.5KWInverter plus reduction box6Temperature ControllingPLD7Ways of Flower roller HeatingHydraulic Heating8Heating Power48KWThree roller embossing machine Features:(1). The electronic heating controller is used to control the temperature, and the control accuracy is ± 5 °C.(2). Electronic thermostat, digital more intuitive, easy to adjust.(3). Adopt cylinder limit operation mode.Advantages:1.Factory outlets2. Easy to install3. Durable: 10 years guarantee4. European standard5. Durable, applied and secure Quality control:1. Checking raw material before producing.2. Checking one by one before the assembling3. Checking one by one during the production4. Have the random inspection before the delivery.Installation in clients factory:FAQ:1.Q: How long is the delivery time ?A: 3-5 working days for samples and 10-25 days for your quantity based on your orders.2. Q: Can the machine be customized as our need, such as put on our logo?A: Surely our machine can be customized as your needs, and put on your logo is also available.3. Q: As the shipping period will take long time, how can you make sure the machine wont be broken?A: Our machine is film wrapped and wooden case, to make sure the machine can be delivered to our customer smoothly, we will use the steel wire to fix the machine with the container.4. Q: If you can go a little lower, I would be able to give you an order on the spot?A: Considering our good relationship and future business, we give a 3% discount.5. Q: About the after-sale service, how can you solve the problems occurred of your overseas customer in time?A: The warranty of our machine is normally 12 months, during this period, we will arrange the international express immediately, to make sure the replace parts to be delivered as soon as possible.Products certificate
Security camera installation accessories.1.Product Introduction of the security camera installation accessories.This security camera installation accessories was the latest production high quality with OEM ODM manufacture experience. It was die casting aluminum .We devoted ourselves to aluminum die casting part for many years, covering most of Europe and the Americas market. We are expecting become your long-term partner in China2.Product Parameter of the security camera installation accessories3.Product Feature And Application of the security camera installation accessoriessecurity cameras 4.Production Details of the security camera installation accessoriesPlace of Origin: Zhejiang, China (Mainland)Brand Name: FriendlyApplication: Security camerasMaterial: AluminumDimensions: OEM, Customized SizesCertification: ISO9001/ Utility model patent certificateSerivce: OEM/ODM/Customized/DesignSurface treatment: Powder Coated.Drawing formation:2D and 3D igs or stp formatDelivery: 3-4 weeks for mould and 3-5 days for samplesTolerance:+/-0.01mm 5.Product Qualification of the security camera installation accessories.6.Deliver,Shipping And Serving of the security camera installation accessories.Packaging Details: 1,With plastic bag,with pearl-cotton package. 2,To be packed in cartons. 3,Use glues tape to seal cartons. 4,Deliver out by DHL,FEDEX, UPS. Or according to customers' requirement.Port:ShanghaiLead Time :30-45DAYS 7.FAQQ: Are you trading company or manufacturer?A: We are factory.Q: How long is your delivery time?A: Mold leadtime:Within 30 days upon we receive the 50% of mold charges.Batch production leadtime: With 15 days upon we receive the 30% deposit.Q: Can you make the parts based on the samples?A: Yes, we could make measurement based on your samples and make the tooling die.Q: What is your terms of payment ?A: Mold :50% deposit +50% after the samples is approved.Batch production: 30% deposit +70% before shipment.Q: Do you provide samples ? is it free or extra ?A: Yes, we could offer the sample for free charge but Pay first Return the sample fee after good shipping.Q: What do I need for offering a quote ?A: Please offer us 2D or 3D drawings (with material, dimension, tolerance, surface treatment and other technical requirement etc.) ,quantity, application or samples. Then we will quote the best price within 24h.Q: How long is your delivery time?A: Generally it is 5-10 days if the goods are in stock. or it is 35-45 days if the goods are not in stock, it is according to quantity.Q: How to enjoy the OEM/ custom services ?A: Usually, base on your design drawings or original samples, we give some technical proposals and a quotation to you, after your agreement, we produce for you.8.Latest News 9.Recommendations
surveillance camera parts and accessories1.Product Introduction of the surveillance camera parts and accessories.This surveillance camera parts and accessories manufacturers was the latest production high quality with OEM ODM manufacture experience. It was die casting aluminum .We devoted ourselves to aluminum die casting part for many years, Covering most of Europe and the Americas market. We are expecting become your long-term partner in China2.Product Parameter of the surveillance camera parts and accessories.3.Product feature and applicationof the surveillance camera parts and accessories.security cameras 4.Production details of the surveillance camera parts and accessories.Place of Origin: Zhejiang, China (Mainland)Brand Name: FriendlyApplication: Security camerasMaterial: AluminumDimensions: OEM, Customized SizesCertification: ISO9001/ Utility model patent certificateSerivce: OEM/ODM/Customized/DesignSurface treatment:Powder Coated etc.Drawing formation:2D and 3D igs or stp formatDelivery: 3-4 weeks for mould and 3-5 days for samplesTolerance:+/-0.01mm 5.Product Qualification of the surveillance camera parts and accessories. 6.Deliver,Shipping And Serving of the surveillance camera parts and accessories.Packaging Details: 1,With plastic bag,with pearl-cotton package. 2,To be packed in cartons. 3,Use glues tape to seal cartons. 4,Deliver out by DHL,FEDEX, UPS. Or according to customers' requirement.Port: ShanghaiLead Time :30-45DAYS 7.FAQQ: Are you trading company or manufacturer?A: We are factory.Q: How long is your delivery time?A: Mold leadtime:Within 30 days upon we receive the 50% of mold charges.Batch production leadtime: With 15 days upon we receive the 30% deposit.Q: Can you make the parts based on the samples?A: Yes, we could make measurement based on your samples and make the tooling die.Q: What is your terms of payment ?A: Mold :50% deposit +50% after the samples is approved.Batch production: 30% deposit +70% before shipment.Q: Do you provide samples ? is it free or extra ?A: Yes, we could offer the sample for free charge but Pay first Return the sample fee after good shipping.Q: What do I need for offering a quote ?A: Please offer us 2D or 3D drawings (with material, dimension, tolerance, surface treatment and other technical requirement etc.) ,quantity, application or samples. Then we will quote the best price within 24h.Q: How long is your delivery time?A: Generally it is 5-10 days if the goods are in stock. or it is 35-45 days if the goods are not in stock, it is according to quantity.Q: How to enjoy the OEM/ custom services ?A: Usually, base on your design drawings or original samples, we give some technical proposals and a quotation to you, after your agreement, we produce for you.8.Latest News9.Recommendations
Die casting aluminum parts for lifter1.Product Introduction of the die casting aluminum parts for lifterThis die casting aluminum parts for lifter was the latest production high quality with OEM ODM manufacture experience. It was die casting aluminum .We devoted ourselves to aluminum die casting part for many years, covering most of Europe and the Americas market. We are expecting become your long-term partner in China.2.Product Parameter of die casting aluminum parts for lifter.3.Product Feature And Application of the die casting aluminum parts for lifter.lifter 4.Production Details of the die casting aluminum parts for lifterPlace of Origin: Zhejiang, China (Mainland)Brand Name: FriendlyApplication: electrical applianceMaterial: AluminumDimensions: OEM, Customized SizesCertification: ISO9001Serivce: OEM/ODM/Customized/DesignSurface treatment: Painting/sand blasting /painting/aluminum plated etc.Drawing formation:2D and 3D igs or stp formatDelivery: 3-4 weeks for mould and 3-5 days for samplesTolerance:+/-0.01mm 5.Product Qualification of die casting aluminum parts for lifter .6.Deliver,Shipping And Serving of the die casting aluminum parts for lifter.Packaging Details: 1,With plastic bag,with pearl-cotton package. 2,To be packed in cartons. 3,Use glues tape to seal cartons. 4,Deliver out by DHL,FEDEX, UPS. Or according to customers' requirement.Port:ShanghaiLead Time :30-45DAYS7.FAQQ: Are you trading company or manufacturer?A: We are factory.Q: How long is your delivery time?A: Mold lead time: Within 30 days upon we receive the 50% of mold charges.Batch production lead time: With 15 days upon we receive the 30% deposit.Q: Can you make the parts based on the samples?A: Yes, we could make measurement based on your samples and make the tooling die.Q: What is your terms of payment ?A: Mold :50% deposit +50% after the samples is approved.Batch production: 30% deposit +70% before shipment.Q: Do you provide samples ? is it free or extra ?A: Yes, we could offer the sample for free charge but Pay first Return the sample fee after good shipping.Q: What do I need for offering a quote ?A: Please offer us 2D or 3D drawings (with material, dimension, tolerance, surface treatment and other technical requirement etc.) ,quantity, application or samples. Then we will quote the best price within 24h.Q: How long is your delivery time?A: Generally it is 5-10 days if the goods are in stock. or it is 35-45 days if the goods are not in stock, it is according to quantity.Q: How to enjoy the OEM/ custom services ?A: Usually, base on your design drawings or original samples, we give some technical proposals and a quotation to you, after your agreement, we produce for you.8.Latest News9.Recommendations
Home security camera parts1.Product Introduction of the home security camera parts.This home security camera parts was the latest production high quality with OEM ODM manufacture experience. It was die casting aluminum .We devoted ourselves to aluminum die casting part for many years, covering most of Europe and the Americas market. We are expecting become your long-term partner in China2.Product Parameter of the home security camera parts3.Product Feature And Application of the home security camera partsHome security cameras 4.Production Details of the home security camera partsPlace of Origin: Zhejiang, China (Mainland), Zhejiang, China (Mainland)Brand Name: FriendlyApplication: Home security camerasMaterial: AluminumDimensions: OEM, Customized SizesCertification: ISO9001/ Utility model patent certificateService: OEM/ODM/Customized/DesignSurface treatment: Powder coated.Drawing formation:2D and 3D igs or stp formatDelivery: 3-4 weeks for mould and 3-5 days for samplesTolerance:+/-0.01mm 5.Product Qualification of the home security camera parts.6.Deliver,Shipping And Serving of the home security camera parts.Packaging Details: 1,With plastic bag,with pearl-cotton package. 2,To be packed in cartons. 3,Use glues tape to seal cartons. 4,Deliver out by DHL,FEDEX, UPS. Or according to customers' requirement.Port:ShanghaiLead Time :30-45DAYS 7.FAQQ: Are you trading company or manufacturer?A: We are factory.Q: How long is your delivery time?A: Mold leadtime:Within 30 days upon we receive the 50% of mold charges.Batch production leadtime: With 15 days upon we receive the 30% deposit.Q: Can you make the parts based on the samples?A: Yes, we could make measurement based on your samples and make the tooling die.Q: What is your terms of payment ?A: Mold :50% deposit +50% after the samples is approved.Batch production: 30% deposit +70% before shipment.Q: Do you provide samples ? is it free or extra ?A: Yes, we could offer the sample for free charge but Pay first Return the sample fee after good shipping.Q: What do I need for offering a quote ?A: Please offer us 2D or 3D drawings (with material, dimension, tolerance, surface treatment and other technical requirement etc.) ,quantity, application or samples. Then we will quote the best price within 24h.Q: How long is your delivery time?A: Generally it is 5-10 days if the goods are in stock. or it is 35-45 days if the goods are not in stock, it is according to quantity.Q: How to enjoy the OEM/ custom services ?A: Usually, base on your design drawings or original samples, we give some technical proposals and a quotation to you, after your agreement, we produce for you.8.Latest News9.Recommendations
Security camera wiring accessories1.Product Introduction of the security camera wiring accessories.This security camera wiring accessories was the latest production high quality with OEM ODM manufacture experience. It was die casting aluminum .We devoted ourselves to aluminum die casting part for many years, covering most of Europe and the Americas market. We are expecting become your long-term partner in China2.Product Parameter of the security camera wiring accessories3.Product Feature And Application of the security camera wiring accessoriessecurity cameras4.Production Details of the security camera wiring accessoriesPlace of Origin: Zhejiang, China (Mainland)Brand Name:FriendlyApplication: Security camerasMaterial: AluminumDimensions: OEM, Customized SizesCertification: ISO9001/Utility model patent certificateSerivce: OEM/ODM/Customized/DesignSurface treatment: Powder coated.Drawing formation:2D and 3D igs or stp formatDelivery: 3-4 weeks for mould and 3-5 days for samples Tolerance:+/-0.01mm 5.Product Qualification of the security camera wiring accessories.6.Deliver,Shipping And Serving of the security camera wiring accessories.Packaging Details: 1,With plastic bag,with pearl-cotton package. 2,To be packed in cartons. 3,Use glues tape to seal cartons. 4,Deliver out by DHL,FEDEX, UPS. Or according to customers' requirement.Port:ShanghaiLead Time :30-45DAYS7.FAQQ: Are you trading company or manufacturer?A: We are factory.Q: How long is your delivery time?A: Mold leadtime: Within 30 days upon we receive the 50% of mold charges.Batch production leadtime: With 15 days upon we receive the 30% deposit.Q: Can you make the parts based on the samples?A: Yes, we could make measurement based on your samples and make the tooling die.Q: What is your terms of payment ?A: Mold :50% deposit +50% after the samples is approved.Batch production: 30% deposit +70% before shipment.Q: Do you provide samples ? is it free or extra ?A: Yes, we could offer the sample for free charge but Pay first Return the sample fee after good shipping.Q: What do I need for offering a quote ?A: Please offer us 2D or 3D drawings (with material, dimension, tolerance, surface treatment and other technical requirement etc.) ,quantity, application or samples. Then we will quote the best price within 24h.Q: How long is your delivery time?A: Generally it is 5-10 days if the goods are in stock. or it is 35-45 days if the goods are not in stock, it is according to quantity.Q: How to enjoy the OEM/ custom services ?A: Usually, base on your design drawings or original samples, we give some technical proposals and a quotation to you, after your agreement, we produce for you.8.Latest News 9.Recommendations
We have our own factory and we can customize any types of laser machine according to your requirements Description Fiber laser making machine is one of the most advanced laser marking equipment in the world nowadays, because the features of stable output power, great optical model, excellent quality of laser beam, fast working speed and best marking effect and efficiency. Also, it is easy to operate, has no wearing parts, low power, consumption, more incomparable advantages like:better and thinner marking lines, capable of being applied into ore advanced industries needing higher demand of depth, smoothness and precision, in order to perfectly meet requirements of consecutive working in industries. Our laser marking machine adopts the best quality fiber laser source in the world. We have 10w, 20w, 30w, 50w,70w and 100w for optional. The estimated life for laser source will be around 100,000hours, which is 10 times longer life than diode laser and 2 times longer life than other fiber laser source. Applicable Material Fiber laser marking machine can be used for marking logo, serial number, bar code and other beautiful photo on any metallic materials such as stainless steel, titanium, brass, gold, silver, aluminum and lots of engineering plastic products such as mobile cover & charger, consume electronics housing, and etc. Pre-Sales Service *Free pre-sales consulting / Free sample marking/testing *Any kind of technical support are available for users. *We offer progressing solution design to all the distributor and users. After-Sales Service *3 years warranty (People damaged are charged). * Full technical support\ by e-mail, call and video * Lifelong maintenance and spare parts supply. * Free design of fixtures as customers required. * Free training installation and operation for the staffs. 1.What is your payment term? We can agree T/T,L/C,Western union and other etc. 2.Where did you export? In the past few years, our products have been sold to the United States, Europe, Southeast Asia, Australia, the Middle East and other countries and regions. 3. What services do you supply? Quality Guarantee We arrange final test before shipment.. After making sure machine is the best performance, then ship out the machine. Operating guide Explain the use of machines and software. Guide the customer proper use, extend product life and reduce energy consumption. Warranty The whole set of machine warranty period is 1 year. (People damaged are charged) 4.How long do you finish 1 set Only 1-7days
We have our own factory and we can customize any types of laser machine according to your requirements Fiber laser making machine is one of the most advanced laser marking equipment in the world nowadays, because the features of stable output power, great optical model, excellent quality of laser beam, fast working speed and best marking effect and efficiency. Also, it is easy to operate, has no wearing parts, low power, consumption, more incomparable advantages like:better and thinner marking lines, capable of being applied into ore advanced industries needing higher demand of depth, smoothness and precision, in order to perfectly meet requirements of consecutive working in industries. Our laser marking machine adopts the best quality fiber laser source in the world. We have 10w, 20w, 30w, 50w,70w and 100w for optional. The estimated life for laser source will be around 100,000hours, which is 10 times longer life than diode laser and 2 times longer life than other fiber laser source. If you need to mark color on stainless steel, the MOPA laser source could be choosed. we adopt JPT mopa laser source which has good quality and longlife service. Features: 1. enclosed machine, to protect person from laser injure. 2. automatic door. 3. auto lifting, press button to adjust height. 4. inner red light Galvanometer, auto focus. 5. use for marking and engraving on metal and nonmetal. Applicable Material Fiber laser marking machine can be used for marking logo, serial number, bar code and other beautiful photo on any metallic materials such as stainless steel, titanium, brass, gold, silver, aluminum and lots of engineering plastic products such as mobile cover & charger, consume electronics housing, and etc. Pre-Sales Service 1.Free pre-sales consulting / Free sample marking/testing 2.Any kind of technical support are available for users. 3.We offer progressing solution design to all the distributor and users. After-Sales Service 1. 3 years warranty (People damaged are charged). 2. Full technical support\ by e-mail, call and video 3. Lifelong maintenance and spare parts supply. 4. Free design of fixtures as customers required. 5. Free training installation and operation for the staffs. Package: non-fumigation Plywood case Transportation Mode:Shipping/Air/DHL/TNT(According to your requirements) Delivery Time: 1-7days after receive the payment.
Name: electroplated diamond & CBN grinding wheel for non-ferrous industry application No dressing,Body can be re-plated several times Introduction:Electroplated diamond and Cubic Boron Nitride (CBN) tools are made up of a basic single layer or multi-layers (depending on application) of either diamond or CBN particles that are bonded to the tool surface using a nickel matrix. The product can be made with various shapes and they are suitable for special complicated profile, surface grinding ,Internal grinding, Slot grinding,Profile grinding and small and others form grinding. Electroplated diamond and CBN tools are used for surface grinding ,Internal grinding, Slot grinding,Profile grinding Ceramics, Glass, Tungsten Carbide, Ferrite ,Chilled Cast Iron, Founded Alloy Steel, Titanium Alloy And etc Applications of electroplated bond grinding wheels: diamond tools for non - ferrous industry application * carbide (grinding green and sintered tungsten carbide) * ceramic (grinding ceramics like SIC, AJO,ZrO, etc) * automotive (grinding brake liners and cutting re-enforced rubber mouldings) * pharmaceutical (grinding factitious knee joint) * dental (profiling rubber bonded grinding pins) * ferrite (grinding magnetic parts) * chemical (grinding laboratory glass) * graphite (grinding graphite parts) * glass (grinding tubes, automotive components) * Fiberglass ,Plastics and Electronic components, etc CBN tools for metallic materials industry application * High-speed tool steels * Die steel * Hardened carbon steels * Hardened stainless steels * Alloy steels,Titanium Alloy * Aerospace alloys * Abrasion resistant ferrous materials, etc Advantages of electroplated diamond & CBN wheels: 1.No dressing procedure necessary,Body can be re-plated several times 2.High geometric and proportion precision,Complicated forming 3.retain their original shape and dimensions throughout their working life 4.Simple electroplated process, less investment convenient manufacturing 5.Excellent surface roughness, high grinding efficiency , long tool life 6.free-faster cutting, no dressing, less heating due to the diamond particles protruding from the surface. Please provide us details when you order, For example, Product needed: Resin bond diamond grinding wheel 1) Diameter (25, 40,100,200,300,750mm) 2) Hole/state bore dimension 3) Thickness (4/5/6/8/10/,40/50/60mm) 4) Shape (1A1 /1A1R/1A8/1A1W/1L1/1F1/6A2/12A2/11V9/4A1/14A1,) 5) Grit size (16/18, 18/20,40/45,80/100,325/400. In GB or ISO standard) 6) Other request
Name: electroplated diamond & CBN grinding wheel for non-ferrous industry application No dressing,Body can be re-plated several times Introduction:Electroplated diamond and Cubic Boron Nitride (CBN) tools are made up of a basic single layer or multi-layers (depending on application) of either diamond or CBN particles that are bonded to the tool surface using a nickel matrix. The product can be made with various shapes and they are suitable for special complicated profile, surface grinding ,Internal grinding, Slot grinding,Profile grinding and small and others form grinding. Electroplated diamond and CBN tools are used for surface grinding ,Internal grinding, Slot grinding,Profile grinding Ceramics, Glass, Tungsten Carbide, Ferrite ,Chilled Cast Iron, Founded Alloy Steel, Titanium Alloy And etc Applications of electroplated bond grinding wheels: diamond tools for non - ferrous industry application * carbide (grinding green and sintered tungsten carbide) * ceramic (grinding ceramics like SIC, AJO,ZrO, etc) * automotive (grinding brake liners and cutting re-enforced rubber mouldings) * pharmaceutical (grinding factitious knee joint) * dental (profiling rubber bonded grinding pins) * ferrite (grinding magnetic parts) * chemical (grinding laboratory glass) * graphite (grinding graphite parts) * glass (grinding tubes, automotive components) * Fiberglass ,Plastics and Electronic components, etc CBN tools for metallic materials industry application * High-speed tool steels * Die steel * Hardened carbon steels * Hardened stainless steels * Alloy steels,Titanium Alloy * Aerospace alloys * Abrasion resistant ferrous materials, etc Advantages of electroplated diamond & CBN wheels: 1.No dressing procedure necessary,Body can be re-plated several times 2.High geometric and proportion precision,Complicated forming 3.retain their original shape and dimensions throughout their working life 4.Simple electroplated process, less investment convenient manufacturing 5.Excellent surface roughness, high grinding efficiency , long tool life 6.free-faster cutting, no dressing, less heating due to the diamond particles protruding from the surface. Please provide us details when you order, For example, Product needed: Resin bond diamond grinding wheel 1) Diameter (25, 40,100,200,300,750mm) 2) Hole/state bore dimension 3) Thickness (4/5/6/8/10/,40/50/60mm) 4) Shape (1A1 /1A1R/1A8/1A1W/1L1/1F1/6A2/12A2/11V9/4A1/14A1,) 5) Grit size (16/18, 18/20,40/45,80/100,325/400. In GB or ISO standard) 6) Other request
