Introduction It can replace the traditional AKD emulsifier of cationic starch with the multifunction of AKD emulsification, protection of colloid, retention, strengthening and so on. Cationic polymer AKD emulsifier can be made into AKD emulsion with high stability and retention rate through mechanical stirring method. It can decrease hydrolysis of AKD during the storage period and sizing process, with its storage time two or three months longer than the traditional AKD emulsion, and shorten the sizing curing time. It can be applied in cardboard, corrugated board and other kind of papers. Packing, transport and storage: Store at room temperature, keep in dry and cool. Pay attention to prevent frozen and sunscreen. 1000kg plastic drum, or referring to clients site conditions.
AKD emulsifier is a special emuslfier for AKD wax, starch based, mainly used for emulsifying AKD wax to produce AKD emulsion, ensure AKD granularity is controlled below 1m, protecting sizing retention and increase efficiency. AKD emulsifier is usually used together with AKD wax, AKD dispersant, AKD stabilizer to make AKD emulsion. AMAZON provide technical support for new customers in AKD emulsion production process. Appearance:Red brown liquid Solid content(%):25±1% PH Value:2-6 Viscosity (25, mpa.s):500-2000
Las 1NF- Lactose Substitute Non- Fat Solid is an Enzymatically Modified, Vegan, Gluten-Free, Plant-based, Non-GMO starch used as a Texturizing agent, Taste Improver, Bulking Agent, Volumizing, Emulsifier, Fat Replacer, Stabilizer & Thickener and in Milk and Milk products. It is 100% naturally made which does not have any preservatives and Mono sodium Glutamate (MSG). FEATURES AND BENEFITS *It is highly bio-degradable and causes no harm to the Environment. *A Las 1NF is a white powder that adds no color to application and blends well with other ingredients. *Las 1NF act as an excellent fat replacer, bulking agent, volumizing and taste improver. *Las 1NF act as thickening & binding agent and as emulsifier and stabilizer. *Las 1NF act as texturizing agent for Milk and Milk Products. DOSAGE For excellent results, use 2 to 10% Las 1NF of total batch size, based on the Protein Content of the Milk. For Lower Protein Content in the Milk higher Las 1NF NEED TO BE USED
Stabilisers And Emulsifiers Pectin
Stabilisers And Emulsifiers Xanthan Gum
Stabilisers And Emulsifiers Guar Gum
Stabilisers And Emulsifiers Gum Arabic
Sodium Alginate
Stabilisers And Emulsifiers Agar Agar
Stabilisers And Emulsifiers Carrageenan
Stabilisers And Emulsifiers Gelatin
Product Name: Diacetyl Tartaric Acid Esters of Mono and Diglycerides (DATEM) Type: Food Additives Origin: China CAS No.: 10085-39-0 AUCO No.: 298 Packing: 25kg carton" Items Standard Appearance White fine Powder Purity % 80%ï¼?20% free Flowing agent Acid Value 45-100 mg KOH/g Saponification 280-520 mg KOH/g Total Tartaric Acid % 10-40 Total Glycerol % 11-28 Free Glycerol % 2.0max Ignition Residue % 0.5max Arsenic (by As) 3ppm max Heavy Metals(Pb) 2ppm max
Specifications 1.odorless 2.low VOC 3.antimicrobial 4. mildew resistant 5.environmentally friendly 6.waterproof 7.Scrub resistance Description It is an enhanced mildew proof product adopting nano-scale Ag+ antimicrobial and mildew proof technology, integrating odorless formula, with fresh product smell, smooth paint film, durable and beautiful paint.As an affordable and environmentally friendly product with excellent decorative performance, it is characterized by fresh smell, environmental health, strong covering power, large painting area, convenient constructionapplication, short constructionapplication period, etc. Specification Data Solvent: Water Pigment: Non-lead pigment Theoretical Solids By Volume: more than 50% Theoretical Coverage: Theoretically 1 litre of this product covers 12 sqm in 1 coat Coverage varies considerably depending on application methods and surface roughness and porosity. Shelf Life: Minimum 12 months at 77F(25C) unopened and store in cool and dry places. Recommended Film Thickness: Wet: 80 micron Dry: 30 micron Dry Time: At 77F (25C) and 50% R.H. to recoat Touch Dry: 1 hours Recoat : 2-3 hours Application: Brush, Roll, conventional spray or Airless Spray. Thinner: Thin up 15% depend on different application methods & temperature. Do not over thin by adding more than 30% water. Brush or Roller: For sealing new or bare surfaces thin with up to 1 part of clean water to 5-10 parts of paint(10%-20%) Conventional Spray: Add up to 1 part clean water to 5 parts paint(20%) Airless spray: do not thin Clean-up: Clean up equipment with water Typical painting system Substrate System All kinds of Wall surfaces 1.Alkali Resistance Primer (1 coat) 2.Emulsion Wall Paint (2 coats)
Textile Emulsions We have a broad range of coating products for the TEXTILE INDUSTRY such as Textile finishing agents Strech khadi for hosiery textile printing Ready khadi for textile printing Excellent quality binders for textile printing High quality plastisols
Paint Emulsions We supply wide variety of premium quality water based emulsions for the paint industry. The emulsions are selected based on the applications depending on interior or exterior paint formulation. We also supply paint aids such as thickeners and dispersing agents which are mostly performance polymers used in manufacturing good quality water based Acrylic Paints.
Mono Di Glycerides ( MDG )
We are a leading supplier of electroplating chemicals, industrial polishing and welding consumables, water treatment, powder coating, fertilizers. We stock and carry an extensive range of ready to use chemicals. We deal with so many different chemicals and we would like you to contact us for more information about our different chemicals and products.
Silicone Emulsion 60% is used in industrial applications such as in Rubber and plastics as release agents and lubricants, in Food trays and plastic serving dishes as release agents, in Car polishes and household cleaners to improve protection, resistance, gloss and spread ability and in Textile finishing to enhance feel, water repellency and reduce the need for ironing. Silicone Emulsion 60% is also used in Perlite, vermiculite and clay and other building materials to improve water repellency and protect against dampness. Itâ??s used in Printing and papermaking for lubrication and as an antistatic agent. Silicone Emulsion 60% used as a Release agent for industrial rubber tire plastics and casting materials; Rotary offset printing lubricant; Industrial waterproofing agent and release agent; Additives for maintenance products; Polishing agent for floors and furniture; And Leather maintenance products, etc. Silicone Emulsion 60% WC Code: 24-005-04 Sales Specification Appearance: White Liquid Odour: Characterictic Solid content (%): 60.00 �± 2.0 pH Value: 8.0 �± 1.0 Density (g/cm3): 0.953 �± 0.02 Soluble in water: Miscible Packing 440.92 LB Drum 2204.60 LB IBC Tote
Water Based Acrylic Resin Emulsions for Printing Inks & Varnishes We supply ecoprint range of water based acrylic resin for high gloss water based printing Inks and Varnishes. Our ecoprint range of acrylic resins are REACH / ROHS compliant, Formaldehyde free, APEO free, PVC free, Phthalate free and Azo dyes free.
Fruit juice concentrates & pulps, vegetable juice concentrates & purees, milk products, milk powders, cocoa products, starch products, liquid glucose, dam, oils & fats, meat products, stabilizers, emulsifiers, dairy cultures, enzymes, egg liquid, egg powder, food additives, food chemicals, flavor, colour, natural colour, dry fruits, dried fruits, organic products, dehydrated fruit & vegetable powders, canned products, animal feed, sugar, rice, wheat, fertilizers.
