Everflon FEP Aqueous Dispersion Everflon FEP D50 is an off-white aqueous fluorinated ethylene propylene (FEP) dispersion stabilized with a non-ionic surfactant. It is a general-purpose dispersion that can be used to impart some the unique properties of FEP to end products that would be difficult to make using traditional melt extrusion processes. It can be used to coat or impregnate porous structures, or to make thin films. It can be coated and melt bonded to polytetrafluoroethylene (PTFE) resin or used as a hot melt adhesive. The FEP resin in Everflon FEP D50 is a melt flowable thermoplastic, providing superior properties typical of fluoroplastic resins: retention of properties after service at 204 °C (400 °F) and useful properties at 240 °C (400 °F). Everflon FEP D50 aqueous dispersion provides: Inertness to nearly all industrial chemicals and solvents Stability at high temperatures Excellent dielectric properties Excellent weatherability Application Heat-sealable top coatings for PTFE-coated fabrics for belting, circuit boards, architectural fabrics, and electrical insulation Cast film for capacitor dielectrics or chemical barriers Hot melt adhesive for PTFE, PFA, and FEP parts Metal coatings Processing Conventional dip or flow techniques can be used for coating or impregnating high temperature fabrics, fibers, and other products with Everflon FEP D50. A FEP resin coating on woven fabrics made of fiberglass, fiber, or other high-temperature resistant fibers, can be made by dip coating. Successive passes may be necessary to build the desired thickness to produce a smooth, crack-free coating. Each coating layer is usually dried to remove water (typically at 120 °C [250°F]), baked to remove the wetting agent (typically at 270 °C [518 °F]), and then heated above the crystalline melting point of the resin particles (approximately 265 °C [509 °F]). If the Everflon FEP D50 is being used as a top coat over a PTFE-coated fabric or other parts, the coating must be heated to melt the PTFE (approximately 337 °C [639 °F]) to maximize adhesion. Other solid or liquid ingredients can be added to Everflon FEP D50 to provide specific processing or finished product behavior
2040/1530 thin mild steel sheet CNC plasma table cutting machine is especially designed for thin steel plate ( 0-3 mm )fast cutting. It adopts cylinder compacting system to prevent steel plate moving during cutting. It has a very fast cutting speed for the thin plate. 2040 1530 thin mild steel sheet CNC plasma table cutting machine features: 1. The beam uses light structural design, with good rigidity structure, light deadweight and small movement inertia. 2. STARFIRE control system, the file incision and export automatic correction , real-time tracking detection of plasma power in the process of cutting current. The control system uses the U-disk exchange processing document, easy to operate. 3. Z axis adopts Cylinder pressure, so high precision and long life time using are assured. 4. It can apply to iron sheet, the aluminum sheet, the galvanized sheet, hundred steel plates , metal plates and so on. Equipped with other metal equipment, forming the advertising word processing tubeline. Completely solve the traditional manual processing methods. Improve the efficiency of several times. 5. Cutting kerf is small, tidy, and avoid a second dressing processing. 6. High cutting speed, high precision, and low cost and cheap. 7. Support FASTCAM, Astronautics Haire, ARTCAM software, Type3 produce standard G code way document, also can change software to read AUTOCAD software produce DXF form documents. Applicable Materials: Especially for all kinds of metal materials such as steel, copper, aluminum and stainless steel that thickness less than 8mm cutting. 2040 1530 thin mild steel sheet CNC plasma table cutting machine parameters: Model RB 1560 2040 Working area (X-Y) 1500mm*6000mm, 2000mm*4000mm Working material Iron, Steel, Aluminum, sheets, Galvanized, sheets. Titanium, Plates Working Thickness 0-8mm Cutting Speed 0-12000mm/min Power 8.5kw Input Voltage 380V 50HZ/60HZ Plasma Current 63A Connecting Way USB Working Mode Untouched arc striking Cooling method With water pump and tank provide circulating water cooling Rail guide HIWIN square rails Transmit way Taiwan imported ball screw Operation language Chinese or English Command G code, *uoo, *mmg, *plt Optional power source America HYPERTHERM or China HUAYUAN Spare parts Electrode ,Electricity nozzle and Water jacket
For Sale From Manufacturer- River Materials Up To 90 Cm In Diameter - Crushing Screening Plant (crusher) THE OPPORTUNITY TO PURCHASE HIGH-QUALITY, LONG-LASTING CRUSHING-SCREENING-WASHING PLANTS AT AFFORDABLE PRICES IS OFFERED TO YOU. WE PROVIDE 24/7 SERVICE WITH OUR ENTIRE TEAM TO OFFER THE HIGHEST QUALITY PRODUCTS AND SOLUTIONS TO OUR CUSTOMERS LOCATED IN 5 CONTINENTS AND 52 DIFFERENT COUNTRIES. FURTHERMORE, THANKS TO OUR MANUFACTURING QUALITY, WE PROVIDE A 2-YEAR UNCONDITIONAL WARRANTY AGAINST MANUFACTURING DEFECTS FOR ALL OF OUR PRODUCTS. THE WRITTEN PRICE IN THE ADVERTISEMENT IS APPROXIMATE. FOR A CUSTOM PRICE QUOTE ACCORDING TO YOUR NEEDS, PLEASE CONTACT OUR SALES REPRESENTATIVE. MAIN REASONS TO CHOOSE OUR COMPANY WHY MEGA EXPORT & IMPORT Seamless Communication in Your Preferred Language Punctual Manufacturing �¢?? Shipping and Installation Safe Trading with Fixed Price Guarantee 24/7 Online Support with Experienced Export Team Opportunity to Observe and Monitor the Production Process Online Opportunity to Observe and Monitor the Shipping Process Online Free Substructure Planning Project and Trial Production Easier Trading Opportunity with Leasing and Letter of Credit WHY MEGA CRUSHING �¢?? SCREENING - WASHING PLANTS? High Quality Product with Affordable Price Reduced Energy Consumption �¢?? Minimum Cost Low Costs For Infrastructure and Installation Easy Using Automation Program In Every Language Electrical Panels Operable at Different Energy Levels Affordable Shipment with Demountable Design Low Maintenance Cost and Easily Available Spare Parts in Every Country The Feature of Easy Disassembly from Current Location and Transportability to Another Area SPECIAL WARRANTY AND SERVICE 2 Year Mechanical Warranty Against Manufacturing Defects Sale of Affordable Spare Parts after the Warranty Period Option to Extend Warranty Period to 5 Years with Price Difference International Validity in Warranty Commitments Real-time Fault Detection with Remote Video Connectivity to the Facility Minimum 10 Years Warehouse Availability Guarantee for Each Part 48-Hour Response Time To Domestic Facilities In Case Of Service Required Malfunctions Maximum 72 To 120-Hour Response Time To Facilities Abroad CRUSHING SCREENING PLANTS MANUFACTURED BY US CRUSHING SCREENING PLANT WITH CONE CRUSHER CRUSHING SCREENING PLANT WITH VERTICAL SHAFT CRUSHER CRUSHING SCREENING PLANT WITH HAMMER CRUSHER CRUSHING SCREENING PLANT WITH JAW CRUSHER CRUSHING SCREENING PLANT WITH TERTIARY CRUSHER The infrastructure project required for the crushing and screening plants of your preferred capacity to be established on the site will be provided for free by our company. To watch promotional videos and obtain more detailed information, please visit our website.
120 m3 CAPACITY - MOUNTAIN MATERIAL - CRUSHING AND SCREENING PLANT (CRUSHER) FOR SALE FROM THE MANUFACTURER YOU DON'T NEED TO LOOK FOR A SECONDHAND CRUSHING - SCREENING - WASHING PLANT TO BE ECONOMICAL, DON'T MESS WITH SOMEONE ELSE'S SCRAP... WE OFFER YOU THE OPPORTUNITY TO PURCHASE HIGH QUALITY, LONG-LASTING, CRUSHING-SCREENING-WASHING PLANTS AT AFFORDABLE PRICES. WE ARE AVAILABLE 24/7 WITH OUR ENTIRE TEAM TO OFFER THE HIGHEST QUALITY PRODUCTS AND SOLUTIONS TO OUR CUSTOMERS IN 5 CONTINENTS AND 52 DIFFERENT COUNTRIES. MOREOVER, WE GIVE A 2-YEAR UNCONDITIONAL WARRANTY AGAINST MANUFACTURING DEFECTS TO ALL OUR PRODUCTS BY RELYING ON OUR MANUFACTURING QUALITY. THE PRICE WRITTEN IN THE ADVERTISEMENT IS REPRESENTATIONAL. YOU CAN CONTACT OUR SALES REPRESENTATIVE TO GET A SPECIAL PRICE OFFER ACCORDING TO YOUR NEEDS. THE MAIN REASONS TO CHOOSE OUR COMPANY WHY MEGA EXPORT & IMPORT Easy communication in preferred language On-time production - delivery and assembly Secure trade with fixed price guarantee 24/7 online support with experienced staff for exports Online monitoring of the production process Online tracking of the shipment process Free infrastructure preparation project and test production Easy trade with leasing and letter of credit WHY MEGA CRUSHING - SCREENING - WASHING PLANTS Quality product - affordable price Low energy consumption - minimum cost Low infrastructure and installation costs Easy to use automation program in any language Electric panels that can operate in different energies Economic shipment with disassembled design Low maintenance cost and spare parts readily available in every country Ability to be easily dismantled and moved to another area SPECIAL WARRANTY AND SERVICE Unconditional 2-year mechanical warranty against manufacturing defects Economical spare parts sales at the end of the warranty period Possibility to extend the warranty period to 5 years with a price difference International validity of warranty commitments Instant fault detection with remote connection to the facility Minimum 10-year warehouse stock availability guarantee for each part In case of malfunctions requiring service, 48 hours intervention to our domestic facilities and maximum 72 to 120 hours intervention to our facilities abroad. CRUSHERS AND PLANTS WE PRODUCE CRUSHING PLANTS WITH CONE CRUSHER CRUSHING PLANTS WITH VERTICAL SHAFT CRUSHER CRUSHING PLANTS WITH HAMMER CRUSHER CRUSHING PLANTS WITH JAW CRUSHER CRUSHING PLANTS WITH TERTIARY CRUSHER For the Crushing and Screening Plants in the capacity you prefer, the Infrastructure Project that needs to be built in the area where it be established is given free of charge by our company. Please visit our website to watch promotional videos and get more detailed information.
Aluminum sheet refers to a rectangular frame sheet made by rolling aluminum ingots. It can be pure aluminum sheet or aluminum alloy sheet. According to different application requirements, aluminum sheet can also be divided into different types such as thin aluminum sheet, medium thick aluminum sheet and pattern aluminum sheet. . Aluminum sheets have the characteristics of good light weight, corrosion resistance and thermal conductivity, so they are widely used in construction, automobile, aviation and other fields. The cross-section of the aluminum sheet is rectangular and the thickness is uniform, and when the thickness is greater than 0.2mm, it is usually delivered in a flat shape. Additionally, aluminum panels are often trimmed by shearing or sawing before delivery. Aluminum sheet uses: 1. Construction field. Aluminum panels are used to make building curtain walls, ceilings, interior and exterior wall decorations, etc. They have good fire protection and anti-corrosion properties and are suitable for exterior and interior decoration of high-rise buildings, commercial buildings, airport terminals, squares, stadiums and other buildings. 2. Transportation field. Aluminum sheets are used to make car bodies, roofs, windshield frames and other components. Because of their light weight and high strength, they help improve the fuel efficiency and safety of cars. 3. Electronic field. Aluminum sheets are used to make casings, heat sinks, circuit boards, etc. of electronic products. Due to their conductivity and corrosion resistance, aluminum circuit boards are widely used in electronic products. 4. Packaging field. Aluminum sheets are used to make food packaging, cosmetic packaging, etc., and have good moisture-proof, anti-oxidation, and fresh-keeping properties. 5. Aerospace field. Aluminum sheets are used to manufacture exterior panels, fuel tanks, boosters, etc. for aircraft, satellites, and other equipment. Because of their high strength, light weight, and corrosion resistance, aluminum materials have been widely used in the aerospace field. 6. Other fields. Aluminum sheets can also be used for mechanical parts processing, mold manufacturing, chemical pipeline wrapping, etc. Advantages of aluminum sheets: 1. Low density 2. Good electrical and thermal conductivity 3. Uniform coating and various colors 4. Easy to process 5. Strong corrosion resistance
We are here to be your reliable partners of modified plastics. Engineering plastic is the high-performance plastic that can apply in different industrial areas, the higher mechanical strength and heat resistance of these modified plastics make them an excellent alternation of metal material. Compare to metal parts, engineering plastics are with lots of advantages, such as being weightless, significantly reducing noise, decay resistance, high durability, cold/heat resistance, flame retardant, etc. and are suitable for working in extreme environments. As a professional e engineering plastic supplier/manufacturer, we strive to know the needs and wants of our customers, ANMEI offers different types of engineering plastics - PA6 reinforce, PA66 reinforce, PC/ABS alloy, MABS, TPU FR and PP FR with glass fiber, these engineering plastics are with different performances to adapt to kinds of industries including 5G fiber optic cables, domestic appliances, automobiles, hardware appliances, new energy, clothing, machinery industry, electronics and electrical field. When the right engineered plastic is matched to the right application, the engineering plastic products usage will last longer and the overall performance will be better, making it more competitive in the market. How Could Anmei Engineering Plastics Become Your Choice Anmei, an experienced plastic products engineering company, will customize engineering plastics to meet the product performance or process according to the customer's product and mold structure. Providing customers with engineering plastic services such as consulting, product testing and analysis of engineering plastic material, sample trial production and process guidance. Implement the lean production management model of Japanese companies to reduce hitech plastics engineering production losses. While providing products with material performance comparable to those produced in Europe and the United States, it has a better price advantage. In order to ensure product quality and quality stability between batches, Anmei, a prime engineered plastics corp, uses German production equipment and the technical processes of fortune 500 companies and fully equipped testing laboratories for testing. What are engineering plastics? Engineering plastics are a group of plastic materials that exhibit significantly improved mechanical properties over a wide range of temperatures, loads and times. Especially long-term suitability at temperatures in excess of 90C to at least 150C is considered an important criterion of engineering plastic products. Therefore, all "high temperature" plastics are considered engineering plastics.
Medicinal aluminum foil is generally made of electrolytic aluminum with a purity of more than 99% and is rolled. Aluminum has the advantages of abundant resources, low price, and easy processing. When used as pharmaceutical packaging materials, aluminum foil is the only metal material in the packaging materials. Aluminum foil is non-toxic, odorless, has excellent electrical conductivity and light-shielding properties, has extremely high moisture resistance, gas barrier properties and taste retention properties, and can effectively protect the packaged items. It is a packaging material that has yet to be replaced. Commonly used alloy numbers for medicinal aluminum foil: PTP medicinal aluminum foil: PTP medicinal aluminum foil is also called medicinal plate aluminum foil and capsule aluminum foil. It is mostly made of 8011-H18 aluminum foil or 8011-O aluminum foil. Blister medicinal aluminum foil: Blister aluminum foil is also called cold-formed medicinal foil. It is mostly made of 8021-O aluminum foil and is used for high-end high-end airtight, moisture-proof and light-shielding pharmaceutical packaging. The thickness is 0.04-0.065 mm; Medicinal tropical aluminum foil: Tropical aluminum foil is also called aluminum-plastic aluminum. Tropical blister packaging is equivalent to adding a cold stamped aluminum foil cover on the outside of a thermoformed plastic blister and PTP aluminum foil. 8021-O aluminum foil and 8079-O aluminum foil are mostly used, which are high-end packaging aluminum foils for pharmaceutical packaging; Advantages of medicinal aluminum foil: 1. High-precision printing, rich colors and clear patterns; plain foil can be printed online on automatic pharmaceutical blister packaging machines. 2. It has excellent light-shielding, moisture-proof, oxygen-blocking, moisture-proof, chemical stability and fragrance-preserving properties. 3. The protective layer has excellent high temperature resistance, and the heat sealing layer has good heat sealing performance. It can be heat sealed to PVC, PVC/PVDC, NY/AL/PVC and other composite sheets with good sealing performance. 4. Aluminum foil is used as the base material, which is easy to push or puncture, making it convenient for consumers to take. The packaged blister board is easy to carry, easy to transport, store and prevent contamination. 5. Suitable for high-speed automated production, and can provide products with different width specifications according to the user's packaging machine model.
Product Description Meat Grinder, Fresh meat grinder, Frozen meat grinder, meat mincer, meat chopper, meat crusher, meat extruder machine Meat mincing machine Meat mincer machine 1. Stage is the meat industry general applicability of high, a meat processing equipment, rely on the screw will push the raw meat hopper box in advance to electricity cut through screw rotation function, make reamer with orifice relative motion of raw meat, which will cut into the particle shape, ensure the uniformity of the meat. 2. Excellent versatility, wide range, high production efficiency. Has frozen, fresh ground meat function, save time, energy and good quality. Ground cut process is short term. Low temperature, beneficial to the preservation, extend shelf life. 3. Positive &negative function, make stage for zero, a variety of blocking probability, the more suitable for combination orifice plate requirements of different products. 4. Stuffing mix machine is necessary equipment for mixing, high efficiency, easy operation, is the production of dried cured salami products, grains, mashed mixed intestinal products, pill of choice for equipment products, but also the production of dumplings, wonton noodles class optional equipment products. Advantages: 1. High efficiency, mixing speed 2. Simple operation, easy to ease 3. Automatic discharge, lower labor intensity 4. Arranged in a unique form of rotating teeth to make the material more evenly mixed, single-added material for more 5. The unique three-layer sealed to protect the equipment longer life, easier cleaning function: granular, powder, sludge, paste, slurry Jieyou good adaptability and mixing. Better on the lump type of insurance, with reversing function, with automatic discharging function. Technical data sheet: Model Capacity (kg/h) Power (kw) Twisted dragon speed (r/min) Voltage (v) Dimension (mm) Weight (kg) BG-100 500-800 5.5 250 380 900*580*1000 180 BG-120 1000-1500 7.5 245 380 1070*600*1100 260 BG-130 2000-3000 11 190 380 1200*800*1400 400 BG-250 3000-5000 37 47 380 2060*1070*1610 1500
Xiongcai Motor Controller XCA107 Designed For Automotive Engine Cooling 1. Voltage DC16~36V 2. Rated Current 4.6A 3. Working Temp -40 125 4. Working Humidity 95% 5. Size: 61*56*17mm 6. Protection under voltage, over voltage, low temperature, over temperature, plugging, reverse connection, short circuit 7. PWM speed regulation Established in 2011, founded by experienced engineer, XIONGCAI TECH is a pioneer in specialized field of motor controller (electronic speed control or ESC), especially in water pump for auto engine cooling. Xiongcai had engineered a motor controller for automotive engine cooling---XCA107, which has been using in automotive engine for years. ACHR, a company rooted in automotive water pump for decades, contacted us and inquired about motor controller for automotive water pump. The client was really picky and particular, their engineer team set a standard on protection measure beyond the industry. They said they had met several suppliers, some items of the standards were unacceptable, because if all items met this extremely high standard, the cost would exceed cost budget. Xiongcai team wanted to give a shot. Engineered from ground up, Xiongcai R&D team designed a combination of software and hardware meticulously called XCC107, making all parameters up to customers standard. After one year test and verification, Xiongcai XCA107 motor controller for water pump was approved. The client has introduced this product for several years till now. Xiongcai XCA107 Motor Controller for water pump provides protection measures including under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit, this means the motor controller may stop working due to some reason but never be damaged. We are one of the few engineering companies providing a full service from design to supply of product, which means we design, analyze, test and supply finished products. Xiongcai motor controllers have been applied to many top brands in auto industries, such as Jingyi Group, ACHR, FAW Group, FAWDE, Shenhai Electrical Appliances, Kesen, Cummins and more. Contact us Shenzhen Xiongcai Technology Co., Ltd for more detail, we deliver excellent solution to you.
Features for the DuroMax XP11500EH Generator Plenty of Power With 11,500 starting watts and 9,000 running watts, this unit can handle heavy loads, from lights and a refrigerator to a home air conditioner and high amperage power tools. Dual Fuel Technology This generator runs on gasoline or propane, giving you the freedom and flexibility of fuel choice. Powerful Engine â?? The DuroMax 457cc OHV engine is a workhorse that provides plenty of power to handle multiple jobs, from powering high voltage appliances to heavy duty power tools. Low Oil Shutoff â?? Protects your investment by automatically shutting the generator off when it senses that the oil is low. Fully Featured Power Panel â?? The power panel includes a wide selection of outlets for maximum compatibility in your applications including: 2 120V household GFCI outlets, 1 120V 30A twist lock outlet, 1 240V 30A outlet, and one 240V 50A outlet. The panel also includes a digital voltmeter. Complies with Emissions Standards â?? All DuroMax generators are both approved by the EPA (Environmental Protection Agency) and CARB (California Air Resources Board) and follow strict guidelines to ensure our generators are as environmentally friendly as possible. Included Oil Funnel Spark Plug Wrench Tool Set Wheel & Handle Kit Propane Regulator Ownerâ??s Manual Specifications (POWER) GASOLINE Peak Watts: 11,500 Running Watts: 9,000 Peak Amps @ 120V: 95.83 Running Amps @ 120V: 75.00 Peak Amps @ 240V: 47.92 Running Amps @ 240V: 37.50 PROPANE Peak Watts: 10,925 Running Watts: 8,550 Peak Amps @ 120V: 91.04 Running Amps @ 120V: 71.25 Peak Amps @ 240V: 45.52 Running Amps @ 240V: 35.63 PRODUCT SPECIFICATIONS Amperage: 75.00A / 37.50A Voltage: 120V / 240VAC Frequency: 60 Hz Engine Size: 457 cc Engine Type: 4-Cycle Air-Cooled Spark-Ignition Engine Speed: 3600 rpm Fuel Type: Gasoline / Propane Fuel Tank Capacity (Gasoline): 8.3 gal Suggested Tank Size (Propane): 40 lbs. Runtime (Gasoline) at 50% Load: 8 hrs. Runtime (Propane) at 50% Load: 6 hrs. Start Type: Electric / Recoil Volume Level: 72 dB EPA Certified: Yes CARB Certified: Yes Product Dimensions: 29" L x 30" W x 26" H Product Weight: 224 lbs.
Features for the DuroMax XP10000HX Generator Digital Command Center: All-new control center with a digital multimeter, push-button start, and a front-facing fuel interface allowing you to change your fuel type in seconds! The digital multimeter displays voltage, frequency, total hours run, and hours until the recommended maintenance. Duel Fuel: This generator runs on gasoline or propane, giving you the freedom and flexibility of fuel choice. Why Dual Fuel? Learn more about Dual Fuel technology Equipped with Co Alert: Equipped with DuroMax CO Alert technology that will automatically shut down the generator if an unsafe level of carbon monoxide is detected. Built using a powerful 439cc OHV DuroMax engine and features ALL COPPER WINDINGS designed to make your generator last for years. Powerful: The fully loaded power panel includes four 120V GFCI household outlets, one 120V 30AMP outlet, one 120/240V 30AMP twist-lock outlet, and a heavy-duty 120/240V 50AMP outlet making it transfer switch ready! Onboard the XP10000HX are individual circuit breakers, idle control, and a low oil sensor. Included Oil Funnel Spark Plug Wrench Tool Set Wheel & Handle Kit Propane Regulator Ownerâ??s Manual Specifications (POWER) GASOLINE Peak Watts: 10,000 Running Watts: 8,000 Peak Amps @ 120V: 83.33 Running Amps @ 120V: 66.67 Peak Amps @ 240V: 41.67 Running Amps @ 240V: 33.33 PROPANE Peak Watts: 9,500 Running Watts: 7,600 Peak Amps @ 120V: 79.17 Running Amps @ 120V: 63.33 Peak Amps @ 240V: 39.58 Running Amps @ 240V: 31.67 PRODUCT SPECIFICATIONS Amperage: 66.67A / 33.33A Voltage: 120V / 240VAC & 12VDC Frequency: 60 Hz Engine Size: 439 cc Engine Type: 4-Cycle Air-Cooled Spark-Ignition Engine Speed: 3600 rpm Fuel Type: Gasoline / Propane Fuel Tank Capacity (Gasoline): 8.2 gal. Suggested Tank Size (Propane): 40 lbs. Runtime (Gasoline) at 50% Load: 10.4 hrs. Runtime (Propane) at 50% Load: 8.6 hrs. Start Type: Electric / Recoil Volume Level: 72 dB EPA Certified: Yes CARB Certified: Yes Product Dimensions: 29" L x 30" W x 26" H Product Weight: 228 lbs.
Features and benifits Monitoring scope HR, ECG, SPO2, NIBP, RESP, TEMP, CO2 (optional). 1024*768 color LCD display, full viewing angle display, 10-level brightness adjustment; The vertical button layout on the right side satisfies the quick operation of various scenarios; 30-second blood pressure measurement, performance, function, all-around; ECG 12-coreanti-interference socket design; There are three filtering modes of monitoring, diagnosis and surgery, to satisfy various scenarios; There are more than three ways to enter the alarm limit setting, and there is no need to operate too much for newly received patients; Support fast import/export of USB configuration to meet the needs of different departments; Large storage capacity: it can meet the data storage requirements of continuous patient monitoring for at least 960 hours; With blood pressure STAT measurement mode, it will automatically exit after 5 minutes of continuous measurement; With automatic blood pressure measurement interval time adjustment above level 10, to meet the needs of different patients for monitoring; Support Multi-language, Chinese, English, Italian, Spanish, Turkish, Portuguese, Polish, Germany, Russian; convenient operation of patient information entry\delete\save; 20 kinds of arrhythmia event alarms, support ST segment analysis function; Trigger the printing function, record every abnormality in time; improve the communication efficiency between nurses and doctors (optional); Double overpressure protection of blood pressure software and hardware to ensure patient safety; six groups of data are displayed on the same screen, and trend analysis is clear at a glance; Super long alarm light, 360-degree visibility, easier to monitor patient status information; The alarm sound and the pulse rate sound are independent, the pulse rate sound continues to respond when the alarm is muted, and the alarm sound can be activated normally when the pulse rate sound is muted; The waveform display has two ways of curve and filling to meet the needs of different departments; Large-capacity built-in lithium battery, continuous working time 300 minutes; When the waveform screen is frozen, the real-time parameters are continuously displayed in the parameter area; the frozen waveform can be viewed forward and backward along the time axis. Anti-defibrillation, anti-electric knife, anti-power grid, anti-myoelectric and other interference; Low battery alarm, no data loss at critical moments; Support USB firmware upgrade outside the machine, get rid of local restrictions.
Zooming Manufacturing inc. is a subsidiary of Dongguan Yamei Precision Machinery Parts Co., Ltd., located in Wangniudun Town, Dongguan City. It mainly serves high-tech fields such as automation, aviation, basic scientific research, optical fiber, communication, semiconductor, electronics, medical equipment, shock absorbers and other equipment parts precision processing services. At present, the company has advanced detection instruments such as 5-axis fully automatic coordinate measuring machines (CMM) and optical projectors, as well as production equipment such as multi axis CNC cars, core walking machines, 4-axis and 5-axis CNC milling, automatic flat grinding, wire cutting, and electrical discharge molding. The main equipment is manufactured in the United States and Japan. Our surrounding supporting facilities are also very complete, including laser marking, welding, chemical etching, heat setting, surface sandblasting, polishing, harmless electroplating, passivation/oxidation/dyeing treatment, ultra clean assembly, packaging, etc. We can implement one-stop services to save customers more time and cost, and achieve a win-win situation. The humanized management system has gathered a group of excellent employees and high-quality management personnel, which gives us more confidence and ability to complete various complex technical tasks and meet the standards required by customers. As a result, it has received praise from many world-renowned enterprises in Europe, the United States, and Asia, and has become one of its qualified suppliers, achieving significant growth in business volume. Meitech Company always maintains a steadfast and steady style, promoting the continuous improvement of enterprise management level with the spirit of unity, self-discipline, diligence, rigor, and innovation. We strictly adhere to the TS16949 and ISO9001:2015 standards, and abide by their regulations has become a principle of our daily work. In order to adapt to the trend of global economic integration, we have continuously reduced production costs, improved product reliability and consistency using CNC mass production methods, and have begun to achieve results. Using high-quality products, low prices, punctuality and trustworthiness, and giving back to customers. I believe that the excellent quality and honest and friendly corporate image of Zooming Manufacturing inc will be increasingly valued and recognized by the public. We warmly welcome customers from home and abroad to come and guide us, negotiate cooperation, and create brilliance together.
Zooming Manufacturing inc. is a subsidiary of Dongguan Yamei Precision Machinery Parts Co., Ltd., located in Wangniudun Town, Dongguan City. It mainly serves high-tech fields such as automation, aviation, basic scientific research, optical fiber, communication, semiconductor, electronics, medical equipment, shock absorbers and other equipment parts precision processing services. At present, the company has advanced detection instruments such as 5-axis fully automatic coordinate measuring machines (CMM) and optical projectors, as well as production equipment such as multi axis CNC cars, core walking machines, 4-axis and 5-axis CNC milling, automatic flat grinding, wire cutting, and electrical discharge molding. The main equipment is manufactured in the United States and Japan. Our surrounding supporting facilities are also very complete, including laser marking, welding, chemical etching, heat setting, surface sandblasting, polishing, harmless electroplating, passivation/oxidation/dyeing treatment, ultra clean assembly, packaging, etc. We can implement one-stop services to save customers more time and cost, and achieve a win-win situation. The humanized management system has gathered a group of excellent employees and high-quality management personnel, which gives us more confidence and ability to complete various complex technical tasks and meet the standards required by customers. As a result, it has received praise from many world-renowned enterprises in Europe, the United States, and Asia, and has become one of its qualified suppliers, achieving significant growth in business volume. Meitech Company always maintains a steadfast and steady style, promoting the continuous improvement of enterprise management level with the spirit of unity, self-discipline, diligence, rigor, and innovation. We strictly adhere to the TS16949 and ISO9001:2015 standards, and abide by their regulations has become a principle of our daily work. In order to adapt to the trend of global economic integration, we have continuously reduced production costs, improved product reliability and consistency using CNC mass production methods, and have begun to achieve results. Using high-quality products, low prices, punctuality and trustworthiness, and giving back to customers. I believe that the excellent quality and honest and friendly corporate image of Zooming Manufacturing inc will be increasingly valued and recognized by the public. We warmly welcome customers from home and abroad to come and guide us, negotiate cooperation, and create brilliance together.
Zooming Manufacturing inc. is a subsidiary of Dongguan Yamei Precision Machinery Parts Co., Ltd., located in Wangniudun Town, Dongguan City. It mainly serves high-tech fields such as automation, aviation, basic scientific research, optical fiber, communication, semiconductor, electronics, medical equipment, shock absorbers and other equipment parts precision processing services. At present, the company has advanced detection instruments such as 5-axis fully automatic coordinate measuring machines (CMM) and optical projectors, as well as production equipment such as multi axis CNC cars, core walking machines, 4-axis and 5-axis CNC milling, automatic flat grinding, wire cutting, and electrical discharge molding. The main equipment is manufactured in the United States and Japan. Our surrounding supporting facilities are also very complete, including laser marking, welding, chemical etching, heat setting, surface sandblasting, polishing, harmless electroplating, passivation/oxidation/dyeing treatment, ultra clean assembly, packaging, etc. We can implement one-stop services to save customers more time and cost, and achieve a win-win situation. The humanized management system has gathered a group of excellent employees and high-quality management personnel, which gives us more confidence and ability to complete various complex technical tasks and meet the standards required by customers. As a result, it has received praise from many world-renowned enterprises in Europe, the United States, and Asia, and has become one of its qualified suppliers, achieving significant growth in business volume. Meitech Company always maintains a steadfast and steady style, promoting the continuous improvement of enterprise management level with the spirit of unity, self-discipline, diligence, rigor, and innovation. We strictly adhere to the TS16949 and ISO9001:2015 standards, and abide by their regulations has become a principle of our daily work. In order to adapt to the trend of global economic integration, we have continuously reduced production costs, improved product reliability and consistency using CNC mass production methods, and have begun to achieve results. Using high-quality products, low prices, punctuality and trustworthiness, and giving back to customers. I believe that the excellent quality and honest and friendly corporate image of Zooming Manufacturing inc will be increasingly valued and recognized by the public. We warmly welcome customers from home and abroad to come and guide us, negotiate cooperation, and create brilliance together.
Zooming Manufacturing inc. is a subsidiary of Dongguan Yamei Precision Machinery Parts Co., Ltd., located in Wangniudun Town, Dongguan City. It mainly serves high-tech fields such as automation, aviation, basic scientific research, optical fiber, communication, semiconductor, electronics, medical equipment, shock absorbers and other equipment parts precision processing services. At present, the company has advanced detection instruments such as 5-axis fully automatic coordinate measuring machines (CMM) and optical projectors, as well as production equipment such as multi axis CNC cars, core walking machines, 4-axis and 5-axis CNC milling, automatic flat grinding, wire cutting, and electrical discharge molding. The main equipment is manufactured in the United States and Japan. Our surrounding supporting facilities are also very complete, including laser marking, welding, chemical etching, heat setting, surface sandblasting, polishing, harmless electroplating, passivation/oxidation/dyeing treatment, ultra clean assembly, packaging, etc. We can implement one-stop services to save customers more time and cost, and achieve a win-win situation. The humanized management system has gathered a group of excellent employees and high-quality management personnel, which gives us more confidence and ability to complete various complex technical tasks and meet the standards required by customers. As a result, it has received praise from many world-renowned enterprises in Europe, the United States, and Asia, and has become one of its qualified suppliers, achieving significant growth in business volume. Meitech Company always maintains a steadfast and steady style, promoting the continuous improvement of enterprise management level with the spirit of unity, self-discipline, diligence, rigor, and innovation. We strictly adhere to the TS16949 and ISO9001:2015 standards, and abide by their regulations has become a principle of our daily work. In order to adapt to the trend of global economic integration, we have continuously reduced production costs, improved product reliability and consistency using CNC mass production methods, and have begun to achieve results. Using high-quality products, low prices, punctuality and trustworthiness, and giving back to customers. I believe that the excellent quality and honest and friendly corporate image of Zooming Manufacturing inc will be increasingly valued and recognized by the public. We warmly welcome customers from home and abroad to come and guide us, negotiate cooperation, and create brilliance together.
Zooming Manufacturing inc. is a subsidiary of Dongguan Yamei Precision Machinery Parts Co., Ltd., located in Wangniudun Town, Dongguan City. It mainly serves high-tech fields such as automation, aviation, basic scientific research, optical fiber, communication, semiconductor, electronics, medical equipment, shock absorbers and other equipment parts precision processing services. At present, the company has advanced detection instruments such as 5-axis fully automatic coordinate measuring machines (CMM) and optical projectors, as well as production equipment such as multi axis CNC cars, core walking machines, 4-axis and 5-axis CNC milling, automatic flat grinding, wire cutting, and electrical discharge molding. The main equipment is manufactured in the United States and Japan. Our surrounding supporting facilities are also very complete, including laser marking, welding, chemical etching, heat setting, surface sandblasting, polishing, harmless electroplating, passivation/oxidation/dyeing treatment, ultra clean assembly, packaging, etc. We can implement one-stop services to save customers more time and cost, and achieve a win-win situation. The humanized management system has gathered a group of excellent employees and high-quality management personnel, which gives us more confidence and ability to complete various complex technical tasks and meet the standards required by customers. As a result, it has received praise from many world-renowned enterprises in Europe, the United States, and Asia, and has become one of its qualified suppliers, achieving significant growth in business volume. Meitech Company always maintains a steadfast and steady style, promoting the continuous improvement of enterprise management level with the spirit of unity, self-discipline, diligence, rigor, and innovation. We strictly adhere to the TS16949 and ISO9001:2015 standards, and abide by their regulations has become a principle of our daily work. In order to adapt to the trend of global economic integration, we have continuously reduced production costs, improved product reliability and consistency using CNC mass production methods, and have begun to achieve results. Using high-quality products, low prices, punctuality and trustworthiness, and giving back to customers. I believe that the excellent quality and honest and friendly corporate image of Zooming Manufacturing inc will be increasingly valued and recognized by the public. We warmly welcome customers from home and abroad to come and guide us, negotiate cooperation, and create brilliance together.
Zooming Manufacturing inc. is a subsidiary of Dongguan Yamei Precision Machinery Parts Co., Ltd., located in Wangniudun Town, Dongguan City. It mainly serves high-tech fields such as automation, aviation, basic scientific research, optical fiber, communication, semiconductor, electronics, medical equipment, shock absorbers and other equipment parts precision processing services. At present, the company has advanced detection instruments such as 5-axis fully automatic coordinate measuring machines (CMM) and optical projectors, as well as production equipment such as multi axis CNC cars, core walking machines, 4-axis and 5-axis CNC milling, automatic flat grinding, wire cutting, and electrical discharge molding. The main equipment is manufactured in the United States and Japan. Our surrounding supporting facilities are also very complete, including laser marking, welding, chemical etching, heat setting, surface sandblasting, polishing, harmless electroplating, passivation/oxidation/dyeing treatment, ultra clean assembly, packaging, etc. We can implement one-stop services to save customers more time and cost, and achieve a win-win situation. The humanized management system has gathered a group of excellent employees and high-quality management personnel, which gives us more confidence and ability to complete various complex technical tasks and meet the standards required by customers. As a result, it has received praise from many world-renowned enterprises in Europe, the United States, and Asia, and has become one of its qualified suppliers, achieving significant growth in business volume. Meitech Company always maintains a steadfast and steady style, promoting the continuous improvement of enterprise management level with the spirit of unity, self-discipline, diligence, rigor, and innovation. We strictly adhere to the TS16949 and ISO9001:2015 standards, and abide by their regulations has become a principle of our daily work. In order to adapt to the trend of global economic integration, we have continuously reduced production costs, improved product reliability and consistency using CNC mass production methods, and have begun to achieve results. Using high-quality products, low prices, punctuality and trustworthiness, and giving back to customers. I believe that the excellent quality and honest and friendly corporate image of Zooming Manufacturing inc will be increasingly valued and recognized by the public. We warmly welcome customers from home and abroad to come and guide us, negotiate cooperation, and create brilliance together.
Zooming Manufacturing inc. is a subsidiary of Dongguan Yamei Precision Machinery Parts Co., Ltd., located in Wangniudun Town, Dongguan City. It mainly serves high-tech fields such as automation, aviation, basic scientific research, optical fiber, communication, semiconductor, electronics, medical equipment, shock absorbers and other equipment parts precision processing services. At present, the company has advanced detection instruments such as 5-axis fully automatic coordinate measuring machines (CMM) and optical projectors, as well as production equipment such as multi axis CNC cars, core walking machines, 4-axis and 5-axis CNC milling, automatic flat grinding, wire cutting, and electrical discharge molding. The main equipment is manufactured in the United States and Japan. Our surrounding supporting facilities are also very complete, including laser marking, welding, chemical etching, heat setting, surface sandblasting, polishing, harmless electroplating, passivation/oxidation/dyeing treatment, ultra clean assembly, packaging, etc. We can implement one-stop services to save customers more time and cost, and achieve a win-win situation. The humanized management system has gathered a group of excellent employees and high-quality management personnel, which gives us more confidence and ability to complete various complex technical tasks and meet the standards required by customers. As a result, it has received praise from many world-renowned enterprises in Europe, the United States, and Asia, and has become one of its qualified suppliers, achieving significant growth in business volume. Meitech Company always maintains a steadfast and steady style, promoting the continuous improvement of enterprise management level with the spirit of unity, self-discipline, diligence, rigor, and innovation. We strictly adhere to the TS16949 and ISO9001:2015 standards, and abide by their regulations has become a principle of our daily work. In order to adapt to the trend of global economic integration, we have continuously reduced production costs, improved product reliability and consistency using CNC mass production methods, and have begun to achieve results. Using high-quality products, low prices, punctuality and trustworthiness, and giving back to customers. I believe that the excellent quality and honest and friendly corporate image of Zooming Manufacturing inc will be increasingly valued and recognized by the public. We warmly welcome customers from home and abroad to come and guide us, negotiate cooperation, and create brilliance together.
Barcode labels, self-adhesive labels, customized prices, stickers, printing, library barcodes, customized serial numbers. Barcode labels with clear printed content, excellent high temperature resistance, durability, and tensile strength, good chemical corrosion resistance, and high stiffness . Application scope: food, beverage, medicine, daily chemical, digital, mobile, electronics, electrical appliances, automobiles, clothing, logistics Features: Barcode label, clear printed content, excellent high temperature resistance, durability, and tensile strength, good chemical corrosion resistance, high stiffness Application scope: Food, beverages, pharmaceuticals, daily chemicals, digital, mobile phones, electronics, appliances, automobiles, clothing, logistics, hardware, toys, supermarkets, etc Material type: PE, PET, PVC, BOPP, coated paper, synthetic paper, pearlescent film, thermosensitive paper, fragile paper, fluorescent paper, laser film, matte silver/bright silver dragon, silver silk dragon and other non drying adhesive materials Product coverage: Food label, supermarket product label, alcohol label, pharmaceutical label, cosmetics label, digital electronic product label, and special process label. Customized adhesive products, if you need other specifications, please consult us!+86-13924290301 w w w . d h m t t . c o m sales@g z d h m . c n printed labels markers price label labels printed packaging labels Industrial labels sticker printing printable custom label Types include flexographic, digital, pad print, logo and product identification, warning symbol, chemical resistant, tamper evident, barcode, serialized, RFID, instructional. Kraft paper labels Label and Receipt printer Label thermal paper roll digital label label printing systems Suitable for synthetic paper, polyethylene, polyolefin or polypropylene substrate, retail tag, general ticketing, product labeling, pharmaceutical, and shipping applications. business sticker labels custom sticker labels personalized sticker labels return label stickers sticker label printer food label stickers avery sticker labels name label stickers round sticker labels get stickers made transparent labels adhesive labels dicut stickers commercial stickers anniversary stickers equipment stickers corporate stickers inventory sticker approved sticker insurance stickers property stickers standout stickers stickers promotiona diecut stickers
