R-PVS-100 Application Sizing of 100% Cotton Yarn, Denim, Polyester Viscose and Polyester Cotton Partial / Full replacement of PVA, Acrylics, CMC & other binders by polyester size for better economics & performance Chemistry for performance òSizing binder with highest abrasion resistance and flexibility òHigh performance polymer for higher loom efficiency òLow viscosity size, Better penetration. Less hairiness òMinimum loss in elongation. Higher gain in strength & good penetration òBetter surface smoothness and softness after sizing òLess dropping and lesser warp breaks òEasy desizing than PVA òCompatible with starch and other binders òLesser effluent load because of lesser dosage òCan be used like PVA by directly adding to the size mix during cooking for solubilization CHEMISTRY FOR ECONOMICS òFull 2 part of PVA can be replace by 1 part of R-PVS-100 Upto 20kg PVA in Size recipe. òPartial replacement above 20 kg of PVA in Size recipe Physical properties Form/Appearance/Colour/pH of Solution/Solid Content/ : Solid/Free Flowing Powder/Yellow to Greenish/4 û 5/100% Pack Size:25 kg Paper Bag
Sweetener: acesulfame k aspartame saccharin sodium sodium cyclamate neotame sucralose stevia thaumatin nhdc monkfruit extract , function ingredients: erythritol tagatose xylitol stachyose d allulose dextrose mono sorbitol l arabinose isomaltulose ammonium glycyrrhetate monopotassium glycyrrhinate maltodextrin dipotassium glycyrrhetate trehalose tagatose, preservative, potassium sorbate sodium dehydroacetate citric acid , sodium benzoate sodium diacetate malic acid etda na2, thickener sodium carboxymethyl cellulose cmc) xanthan gum, sodium alginate carrageenan gellan gum agar, abrasive, calcium carbonate silicon dioxide (sio2).
The vacuum kneader (banbury mixer) is widely used in the field of sealant with high viscosity, silicon rubber, cmc, battery, ink, pigment, medicine, resin, plastic, cosmetic and so on. It is a kind of high performance and ideal equipment to mix and knead the high viscosity and ultra high viscosity material. Heat transfer oil circulation, electric heating, steam and water cooling as the temperature regulation mode of kneader can be selected. The heating and cooling of the kneader can be done with the structure of jar jacket, wall jacket and filling water or heat transfer oil into stirrers. The modes of material discharge are hydraulic jar turning over, screw discharge and bottom discharge . Jar cover opening and closing can be controlled by hydraulic pressure, the material feeding and discharging are very convenient. The sealing of stirrer shaft adopts the unique balance structure of vacuum box (the national patent no. Is zl200420087991.3) and is favorable in particular in improving the degree of vacuum system and the purity of the material. The kneader consists of 6 parts for kneading part, machine base, driving system, vacuum system, hydraulic system and electric control system. The kneading part consists of jar body, stirrers, wall plates and cover. All the parts contacting with the material are made of stainless steel.
Chemical composition: styrene-acryl ate emulsion Application: used in the surface sizing system of paper and paper board Product characteristics: 1. Good compatibility. It is compatible with anionic, non-ionic additives, CMC, PVA, oxidized starch, dye and fluorescent whitening agent, etc. 2. Low viscosity, so it is easy to deal with. 3. Nice stability. Usage: add this product to the well-gelatinized starch solution at the proportion of 1:10~20 to surface sizing starch, then stir it and add this mixed solution to the machine continuously. Features: 1. It can effectively increase the surface strength and improve the printability of paper. 2. It can reduce the phenomenon of dropping of fiber and powder. 3. It can improve the ink-jet printability and the adhesion of the ink. 4. It could be used to adjust the sizing degree quickly and improve the water resistance of the paper. 5. It doesnt affect the fluorescent whitening performance of the inner sizing agent Note: 1. It is an anionic product, which should avoid being mixed with any ionic product. 2. Its shelf life lasts for 6 months under the temperature of 5-45 degrees. Safety: it doesnt have negative effect on peoples health in the process of shipping, storing and using. 200kg/1000kg per plastic drum
We are Certified By CE, ISO 13485, ISO 9001, CMC Medical Devices and specialized in manufacturing all-dental, Dental Implants Instruments and orthodontic Pliers. We set the standard of the hard work, innovation, and design the dental and orthodontic tools. We use only highest-grade Steel And cover all dental and orthodontic tools against material defects. we understand that instruments shouldn't cost more than necessary. That's why Our factory to door initiative controls pricing and gives you the best quality tools.
1-Potasium Sorbate 2-Xanthan gum food grade 3-Tri Sodium Citrate TTCA or Cofcco 4-Soya Yuwang 5-Craam tar tar 6-Maltodextrine 7-Mono Glycerid 8-Agar agar 9-Citric Acid 10-CMC 11-Ammonium Bicarbonate Food Grade 12-DL-Malic Acid 13-Glycerol Monostearate 14-Lactic Acid Food Grade 15-Sodium Benzoate 16-Sodium Metabisulphite 17-Monosodium Glutamate 18-Ascorbic Acid
1-Potasium Sorbate 2-Xanthan gum food grade 3-Tri Sodium Citrate TTCA or Cofcco 4-Soya Yuwang 5-Craam tar tar 6-Maltodextrine 7-Mono Glycerid 8-Agar agar 9-Citric Acid 10-CMC 11-Ammonium Bicarbonate Food Grade 12-DL-Malic Acid 13-Glycerol Monostearate 14-Lactic Acid Food Grade 15-Sodium Benzoate 16-Sodium Metabisulphite 17-Monosodium Glutamate 18-Ascorbic Acid
1-Potasium Sorbate 2-Xanthan gum food grade 3-Tri Sodium Citrate TTCA or Cofcco 4-Soya Yuwang 5-Craam tar tar 6-Maltodextrine 7-Mono Glycerid 8-Agar agar 9-Citric Acid 10-CMC 11-Ammonium Bicarbonate Food Grade 12-DL-Malic Acid 13-Glycerol Monostearate 14-Lactic Acid Food Grade 15-Sodium Benzoate 16-Sodium Metabisulphite 17-Monosodium Glutamate
Injection mould We are a leading supplier with extensive capabilities to customize any of your engineering, tooling, molding, and manufacturing needs. Our company has the experience and expertise to develop and implement award winning technologies, tooling systems and production for you - our most respected and valued partner. Jinlong is specialized in building a complete plastic injection molding service including design, prototypes, tool making and production of moldings made to your design and injection plastic spare parts. Our design and research team members combine creativity and hard work based on professional softwwares such as cad, cam and cae to satisfy the requirements of our customers. Most used softwares: ug, pro/e, solidworks, auto cad, Main mould processing equipments: Automaic cnc centers (10 sets), imported high precision cmc, charmilles high precision wirecut edm, high precision electric impulse precise factilityes, all this advanced equipment guarantees good quality. Advanced injection and shaping workshops, and injection shot weight is between 45g and 10000g, and we can produce various types of high-quality plastic products under 10000g High quality standard, prompt & effective service, on time delivery, competitive & reasonable price, and responsible after-sales service are the principles we follow to develop the mutual trust and confidence with our domestic and international clients. For more information, please pay a visit to our website. Injection shot weight is between 45g and 10000g, and we can produce various types of high-quality plastic products under 10000g
Items Specifications Results Identification INFRARED ABSORPTION The sample spectrum must match with the spectrum of standard. Complies Appearance White to off-white powder Complies Assay (dry basis), w/% 97.0~102.0 99.12 N-[N-(3,3-Dimethylbutyl)-a- Aspartyl]-L-Phenylalanine, w/% 1.5 0.416 Water, w/% 5.0 4.52 Solubility Very soluble in Alcohol & Ethyl Acetate 1.26 % (w/w) at 25 C in water 4.75 % (w/w) at 60 C in water Complies Specific Rotation am (20,D)/[()dm2 kg-1] -40.0~-43.3 -42.476 Melting point 81 ~84 82.3 Related Substances, w/% 2.0 0.464 Ignited Residue, w/% 0.2 0.07 Residual Solvents Negative Complies pH (5g/L Solution) 5.0~7.0 5.47 Lead (Pb), ppm 1 Complies Total aerobic bacteria 250 cfu/g Complies Coliform 10 mpn/g Complies Fungi 100 cfu/g Complies Shigella Negative Complies Salmonella Negative Complies Staphylococcus aureus Negative Complies Storage Conditions: Preserve in well-closed containers, store in a dry place, and avoid exposure to excessive heat. Shelf Life: 2 years while stored in original packing under above stated condition. Conclusion: The product complies with USP, GB 29944-2013 & (EU) No 231/2012.
Appearance: Cream white/Light Yellow Through 80 mesh:>90 200mesh:
Quality FCC /E200 Function Preservative; mold inhibitor Shelf life 2years Chem. Name 2,4-Hexadienoic Acid Formula C6H8O2 Molecular weight 112.12 CAS-No. 110-44-1 Customs tarif No. 2916-1930 Packaging and storage Store in tight containers protected from light, preferably at a temperature not exceeding 38 Parameters Specification Appearance White Crystalline Powder Heat stability no change in colour after heating for 90 minutes at 105 �°C Identification The sample solution exhibits an absorbance maximum at 254 �± 2 nm Assay 99.0%-101.0% Melting Point 133.0-135.0 C Residue on ignition NMT 0.2% Water NMT 0.5% Point of Sublimation 80 C Aldehydes (as Formaldehyde) NMT 0,1 % Arsenic NMT 3ppm Lead NMT 2ppm Mercury NMT 1ppm Heavy metals (Pb) NMT 10ppm
Quality FCC /E202 Function Antimicrobial agent; preservative Shelf life 2 years Chem. Name Potassium(E,E)-hexa-2,4-dienoate Formula C6H7KO2 Molecular weight 150.22 CAS-No. 24634-61-5 Customs tarif No. 2916-1995 Packaging and storage Store in tight containers Parameters Specification Appearance White Granular or white powder Heat stability no change in colour after heating for 90 minutes at 105 �°C Identification Add a few drops of bromine TS to 2 mL of the sample solution,the color disappears Melting Point 133.0-135.0 �°C Assay 99,0 â?? 101,0% Loss on Drying NMT 1,0% Alkalinity (as K2CO3) NMT 1,0% Acidity (as Sorbic acid) NMT 1,0% Aldehydes NMT 0,1% Heavy metals (as Pb) NMT 10 mg/kg Lead NMT 2 mg/kg Mercury NMT 1 mg/kg Arsenic NMT 3 mg/kg Chloride(as CI) NMT 0.1% Sulfate(as SO4 ) NMT 0.1%
PARAMETER TEST METHOD SPECIFICATION Appearance Visual Off-white to white Powder Taste and Odor Sensory Testing Sweet with cooling, lingering sweet aftertaste without Solvent Total Steviol Glycosides % HPLC JECFA, 2010 99 Rebaudioside A % HPLC JECFA, 2010 97 Stevioside % HPLC JECFA, 2010 Rebaudioside C % HPLC JECFA, 2010 Steviol Equivalents % HPLC 28-36 Absorbance Spectrophotometer 0.05 PH (1 in 100 solution) JECFA Vol.4 4.5-7.0 Loss on Drying % (1052h) JECFA Vol.4 6.0 Residual Ethanol ppm USP 5000 Residual Methanol ppm USP 200 Ash % JECFA, 2010 1 Lead (as Pb ppb AOAC993.14 100 Arsenic (as As) ppb AOAC993.14 20 Mercury (As Hg) ppb AOAC993.14 10 Cadmium (As Cd) ppb AOAC993.14 10 Total Plate Count CFU/g Chapter3, FDA 1000 Yeast & Mold CFU/g Chapter18, FDA 100 Total Coliform MPN/g Chapter4, FDA Negative E. Coli MPN/g Chapter4, FDA Negative Salmonella absent in 25g AOAC/ Negative
Zinc oxide, zirconium silicate, china clay, china clay powder, ball clay, feldspar powder(body), feldspar powder(glaze), feldspar chips, quartz powder(body), quartz powder(glaze), plaster of paris (ta 70, ta 60, ta 50, 75 & 90), talcum powder, dolomite, barium carbonate, sodium bentonite, sodium chloride, cobalt chloride, calcium carbonate(ind), calcium carbonate(food), soda ash light, caustic soda, sodium hydroxide, potassium hydroxide, sodium silicate, potash soap, iron red oxide, iron black oxide, cmc, jailin, colour( ceramic & resin).
Take pride in delivering top quality of water treatment chemicals, mining chemicals, construction chemicals,food additives ect. our competitive pricing combined with flexible trading term make us a trusted partner for businesses worldwide.popular product : sodium chlorite/pam/calcium formate powder/hpmc/cmc/pine oil/texanol. and so many more chemical materials are available..
Brake pads, brake rotors, brake shoes, water pump, air filters, oil filters, cabin filters, bmc, cmc, wheel cylinder assy, shock absorbers, axle boots, steering parts, control arms, head lights, rear lamps, corner lamps, hub bearings, starters and alternators, engine mounts, wiper blades, ignition coils, bushes, radiator hoses, radiators, compressors, condensers, outlets, thermostats, mirrors, door handles, dickey shock, fan motors, fan assy, air cleaner hoses.
Textile Printing Thickener (Thickener) Textile Printing Thickener : ALLIANCE produce Derivatives of Textile Printing Thickener, Thickeners for Printing Fabric based on Guar Gum, Tamarind, Corn Starch and Tapioca Starch for different type of Dyes, Fabrics and Textile Printing Applications. ALLIANCE also produces Tailor Made products for the specific requirement of the customer, based on different kind of fabric and Dyes. For printing of Polyester and its Blends with Disperse Dyes: ALLOPRINT HT (Carboxy Methyl Tamarind) 80, 100 ALLOPRINT DPG (Depolymerized Guar Gum) 60, 80, 100, 120 For Discharge with Stannous Chloride and Burn Out Printing: ALLOPRINT EG (Etherified Guar Gum) 80, 100, 120 ALLOPRINT LV 8, 10 (Carboxy Methyl Tamarind) Textile Printing ThickenerFor Direct Printing and Printing of Silk, Wool and Nylon: ALLOPRINT DPG (Depolymerized Guar Gum) For Vat Discharge : ALLOPRINT DC For Acrylic Blanket and Carpet Printing : ALLOPRINT CPG (Etherified Guar Gum) 20, 30, 40 For Reactive Dyes Printing on Cotton : ALGOTEX Color Enhancer for printing of Disperse Dyes : ALLOPRINT KS 80, 100 (Carboxy Methyl Starch) Food Thickeners : Guar is the most widely used general purpose thickener and texture modifier in the food industry. Derived from the guar plant, Cyamopsis tetragonoloba, that grows in India and Pakistan, guar is all-natural unlike other common thickeners such as modified food starch and cellulose gum (CMC). Because guar imparts viscosity and water-binding capacity even at low usage levels, it is used in applications as diverse as cottage cheese, sauces, soups, and frozen desserts. It is frequently used in stabilizer blends in combination with other gums. Food Thickener : Frozen Foods uses as Water retention, ice crystal inhibitor & stabilizer . Bakery uses as increasing Dough yield, for greater moisture retention and for prolonged shelf life. Processed Cheese uses as increasing the yield of curd solids and improves tenderness. Dairy Products guar gum Inhibits when separation and keeps texture after sterilization. Instant mixes uses as fast, cold dispersible thickening and texturing agent. Canned Foods uses as reducing splash while filling, control viscosity and prevention of fat migration. Beverages uses as Acid resistant thickening and suspending agent. Animal feeding uses as Suspending agent and granulating agent. In Pet Food it uses as Viscosifier.
1. Brief Introduction of Spectrophotometer CS-580 Our spectrophotometers adopt high technology from overseas. It tests based on the condition of D/8 that is internationally used. Our device is widely used for color testing for any industry especially for painting, textile, plastic cement, food, building material and other productsâ?? color quality control. It could connect with color matching software. 2.Advantages of our Spectrophotometer CS-580 1).Obtained Metrology Accreditation Certificate in China 2).Large data storage space 3).Large TFT display screen 4).Modern and fashionable design based on human engineering 5).Easy to operate and compact operation interface 6).Pre-locating panel design for easy instrument calibration 7).Uses LED light source; high capacity rechargeable lithium-ion battery 8).Can measure both SCI(specular included)and SCE(specular excluded) at the same time 9).Includes PC software to manage data 10).Can connect to micro-printers for printing 3. Spectrophotometer Longest Guarantee Time a. One Year Guarantee Time. b. If testing data is not correct, we can do refund. c. We will provide testing report for every device to assure the authority of the data and it will save the calibration cost for 1 year. 4. Technical Data Type:CS-580 Measure Conditions:d/8(Diffused lighting, observe angle:8 degrees) SCS optical engine(light splitting and integration system),ETC(every test calibration), SCI(specular reflection included)/SCE(specular reflection excluded),simultaneous measurement(conform to CIE No.15,ISO 7724/1,ASTM E1164,DIN 5033 Teil7, JIS Z8722 Condition c standards) Size of Integrating Sphere:40mm,Alvan diffused reflection surface coating Illumination Light source:CLEDs(entire wavelength balanced LED light source) Sensor:Double Optical Array Sensor Wavelength Range:400-700nm Measure Range / resolution factor:0-200% , 0.0001 Observation Angle:2°/10 Measurement LightSource:A,C,D50,D55,D65,D75,F1,F2,F3,F4,F5,F6,F7,F8,F9,F10,F11,F12,CWF,U30,DLF,NBF,TL83,TL84 Data being displayed:SPD distribution/data, sample color values, color difference values/graph, pass/fail results, color error tendency, color simulation, display measurement area, history data color simulation, manual input standard sample, generate testing report Measurement time interval: 2 seconds Measuring Aperture:Φ8mm Color space:CIE-L*a*b, L*C*h, L*u*v, XYZ, Yxy, Reflectance Color difference formulas:Î?E*ab, Î?E*CH, Î?E*uv, Î?E*cmc(2:1), Î?E*cmc(1:1),Î?E*94,Î?E*00 Other colorimetric indices:WI(ASTM E313-10,ASTM E313-73,CIE/ISO, AATCC, Hunter, Taube Berger, Ganz, Stensby), YI(ASTM D1925,ASTM E313-00,ASTM E313-73), Tint(ASTM E313,CIE,Ganz), Metamerism index Milm, Stick color fastness, Color fastness Repeatability: standard deviation within 0.08% color values: E*ab
1.CS-820 Colour Spectrophotometer for Textile Advantages 1).Transmittance and reflectance in one instrument 2).Simultaneous SCI/SCE measurement 3).4 Testing Calibers CS-820 colour spectrophotometer contains 4 kinds of testing calibers and the largest reaches 25.4mm. 4).Double optical path spectrum analysis technology 5).It is with large display screen. So the testing result could be directly and clearly seen without connecting with PC. 2.Colour Spectrophotometer CS-820 Technical Data Type:CS-820 Measurement Condition: Reflection: d/8(Diffused lighting, 8 degrees receiving) Compatible with SCI/SCE Measurement ISO7724/1,DIN5033 Teil7,JIS Z8722 condition C,CIE No.15,ASTM E1164) Transmission d/0(Diffused lighting, Vertical direction receiving) Size of integrating sphere:Φ15.2cm, Alvan diffused reflection surface coating Illumination Light source:CLEDs(entire wavelength balanced LED light source) Sensor:dual light path sensor array Wavelength range:400-700nm Wavelength interval: 10nm Half spectral width: 5nm Reflectivity range:0-200% Reflectivity resolution:0.01% Observation angle:2°/10° Measurement light source:A,C,D50,D55,D65,D75,F1,F2,F3,F4,F5,F6,F7,F8,F9,F10,F11,F12 CWF,U30,DLF,NBF,TL83,TL84 Data being displayed: reflectance value and figure, sample's color values, color difference values/graph, pass/fail results, color error tendency, history data color simulation, manual input standard sample, generate measurement report Measurement time interval:2 seconds Reflection Apertures:Large Aperture (LAV):2.54cm (=1inch) Medium Aperture (MAV):1.5cm(=0.6inch) Small Aperture (SAV):0.75cmx1.0cm(0.3inch x 0.4inch) Very Small Aperture (VSAV):0.3cmx0.8cm(0.12inch x 0.31inch) Color space:CIE-L*a*b,L*C*h,CIE-L*u*v,XYZ,Yxy,Transmittance, Hunterlab, Munsell MI,CMYK, RGB,HSB Color difference formulas:Î?E*ab,Î?E*CH,Î?E*uv,Î?E*cmc(2:1),Î?E*cmc(1:1),Î?E*94,Î?E*00 Î?Eab(Hunter),555color classification Other colorimetric indices:WI(ASTM E313-10,ASTM E313-73,CIE/ISO, AATCC, Hunter, Taube Berger, Ganz, Stensby),YI(ASTM D1925,ASTM E313-00,ASTM E313-73),Tint(ASTM E313-00,CIE,Ganz),Metamerism index Milm, Stick color fastness, Color fastness, APHA, Pt-Co, Gardner Repeatability:light splitting reflectivity: standard deviation within 0.08% color values:E*ab
