APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Moisture 20-25% Grade B,C Size: 2-3mm IV: 0.65 Hot wash
IV: 0,4 - 0,6 Not clean, it's from factory Regrind from PET sheet. 1 container/1-1.5 month
Description: IV: 0,4 - 0,6 No washing, from Crush from tray Quantity: 1 or 2 container/per month Loading weight: 23 MT
Specification: Moisture 20-25%; Grade B,C; Size: 2-3mm; IV: 0.65; Hot wash Grade: B and C Origin: Japan Loading Weight: 20MT
Flakes size 3-16mm IV 0.70 plus 1% impurities Quantity a month as you want . Each 40hq can load 23 ton Packing� 25kg� bags
PET Repro Green Plastic Scrap MATERIAL: PET Repro Green CATEGORY: PET TYPE: Repro GRADE: Green SPECIFICATION: "Pure green PET repro pellet, bottle grade Density: 1.35gm/cm3 Pellets size : 3*3 (mm), mesh screen spec 20+100+200+20 IV 0.66+/-0.02 48 tons supply monthly 24 ton per 20' container""" ORIGIN : Bangladesh LOADING WEIGHT : 24 Tons FOB (USD/Ton) : 670-870
Carbon fish meat grill oven process: A. special high temperature resisitant material,high heat deformation,the overall structure uses professtional plate ; B.all into oxygen at the bottom of the damper desigh,fast burning heat rapidly ,at teh top of the air valve design,effective control of heat loss; C. origianl putty separation technology,completely avoiding using process because of the putty mixed soot and open flame,ensure clean,health and safety ; D.equipment applied double high temperature heat insulation material,insulation system,insulation with security,external direct touch with no hidden dangers. Operation method: A. all burning charcoal in the burning charcoal ,open at the top the smooke at the bottom of the mouth and damper; B.charcoal burning closed 10 minutes to the degree of smoke-free smoke at the top of the mouth,the heat; C.after the temperature reaches the standard,in the baking objects to buy object ; D.5-10minutes,bake fish until brown on both sides,are taken from the furnace, the plate feeding . Equipment advantages : A. unique design principle ,the use of charcoal smoke all gathered in the grilled fish inside furnace,through the top of the exhaust pipe directly emitted; B.rapid heat,guarantee the production speed,let the charcoal furnace cavity fully burning rapied heating up,wind valve,and through the top to the bottom of the design of air supply outlet temperature in the furnace in a 300-350 degree,put the fish in the distribution on the stove on content cabinet ,only 8-10 minutes can be produced; C. a novel view and admire a gender ,the design of the gear type appeared in front of customers,the grilled fish process more transparent,more ornamental ,fish and clients directly face to face "communication " ; D this design flexibility ,the real achieve a multi-purpose furnace, can bakering chicken duck cattle and sheep for equipment use diversification more rich . Fuel: dual-use carbon box ,burning charcoal or alcohol (vegetable oil ) ,pump design. Installation and commissioning Overall production : have direct admission requiements,no installation commissioning ,one pace reachs the designated position . 1.Solve the smoke problem charcoal grilled fish we are familiar with most of the fish appeared in the night street food stalls ,a rectangular fish furnace ,a big fan, the air is filled with smoke smell fish .
Medical Alcohol/Ethanol Plant Production Line We professional manufacture of ethanol alcohol equipment ,DDGS ,equipment . The material can be corn(maize) ,wheat,potato,cassava,molasses,beetroot,or any other material which contains starch or sugar .we sell our products to more than 20 countries all over the world. Now our main products are as follow : 1.Turnkey ethanol /alcohol plant project which can produce 95% -96% food grade alcohol,medical alcohol,reagent grade anhydrous ethanol/alcohol or 99.8% fuel grade anhydrous ethanol .Output can be from 1000LPD to 2million LPD . 2.DDGS protein feed equipment ,feed drying equipment . 3.Waste water environmental process equipment 4.Design and manufacture ethanol/alcohol equipment according to customers inquired or drawing .
Fuel Molasses Alcohol/Ethanol Plant We professional manufacture of ethanol alcohol equipment ,DDGS ,equipment .The material can be corn(maize) ,wheat,potato,cassava,molasses,beetroot,or any other material which contains starch or sugar .we sell our products to more than 20 countries all over the world. Now our main products are as follow : 1.Turnkey ethanol /alcohol plant project which can produce 95% -96% food grade alcohol,medical alcohol,reagent grade anhydrous ethanol/alcohol or 99.8% fuel grade anhydrous ethanol .Output can be from 1000LPD to 2million LPD . 2.DDGS protein feed equipment ,feed drying equipment . 3.Waste water environmental process equipment 4.Design and manufacture ethanol/alcohol equipment according to customers inquired or drawing .
75% Medical Ethanol /Alcohol Process Plant We professional manufacture of ethanol alcohol equipment ,DDGS ,equipment ,vine gare equipment in China. The material can be corn(maize) ,wheat,potato,cassava,molasses,beetroot,or any other material which contains starch or sugar .we sell our products to more than 20 countries all over the world. Now our main products are as follow : 1.Turnkey ethanol /alcohol plant project which can produce 95% -96% food grade alcohol,medical alcohol,reagent grade anhydrous ethanol/alcohol or 99.8% fuel grade anhydrous ethanol .Output can be from 1000LPD to 2million LPD . 2.DDGS protein feed equipment ,feed drying equipment . 3.Waste water environmental process equipment 4.Design and manufacture ethanol/alcohol equipment according to customers inquired or drawing .
Cassava ethanol alcohol production line We professional manufacture of ethanol alcohol equipment ,DDGS ,equipment ,vine gare equipment in China. The material can be corn(maize) ,wheat,potato,cassava,molasses,beetroot,or any other material which contains starch or sugar .we sell our products to more than 20 countries all over the world. Now our main products are as follow : 1.Turnkey ethanol /alcohol plant project which can produce 95% -96% food grade alcohol,medical alcohol,reagent grade anhydrous ethanol/alcohol or 99.8% fuel grade anhydrous ethanol .Output can be from 1000LPD to 2million LPD . 2.DDGS protein feed equipment ,feed drying equipment . 3.Waste water environmental process equipment 4.Design and manufacture ethanol/alcohol equipment according to customers inquired or drawing .
Edible Alcohol/Ethanol Plant factory manufacture We professional manufacture of ethanol alcohol equipment ,DDGS ,equipment ,vine gare equipment in China. The material can be corn(maize) ,wheat,potato,cassava,molasses,beetroot,or any other material which contains starch or sugar .we sell our products to more than 20 countries all over the world. Now our main products are as follow : 1.Turnkey ethanol /alcohol plant project which can produce 95% -96% food grade alcohol,medical alcohol,reagent grade anhydrous ethanol/alcohol or 99.8% fuel grade anhydrous ethanol .Output can be from 1000LPD to 2million LPD . 2.DDGS protein feed equipment ,feed drying equipment . 3.Waste water environmental process equipment 4.Design and manufacture ethanol/alcohol equipment according to customers inquired or drawing .
Anhydrous ethanol alcohol plant machine We professional manufacture of ethanol alcohol equipment ,DDGS ,equipment . The material can be corn(maize) ,wheat,potato,cassava,molasses,beetroot,or any other material which contains starch or sugar .we sell our products to more than 20 countries all over the world. Now our main products are as follow : 1.Turnkey ethanol /alcohol plant project which can produce 95% -96% food grade alcohol,medical alcohol,reagent grade anhydrous ethanol/alcohol or 99.8% fuel grade anhydrous ethanol .Output can be from 1000LPD to 2million LPD . 2.DDGS protein feed equipment ,feed drying equipment . 3.Waste water environmental process equipment 4.Design and manufacture ethanol/alcohol equipment according to customers inquired or drawing .
Fuel Alcohol/Ethanol Plant factory manufacture We professional manufacture of ethanol alcohol equipment ,DDGS ,equipment ,vine gare equipment in China. The material can be corn(maize) ,wheat,potato,cassava,molasses,beetroot,or any other material which contains starch or sugar .we sell our products to more than 20 countries all over the world. Now our main products are as follow : 1.Turnkey ethanol /alcohol plant project which can produce 95% -96% food grade alcohol,medical alcohol,reagent grade anhydrous ethanol/alcohol or 99.8% fuel grade anhydrous ethanol .Output can be from 1000LPD to 2million LPD . 2.DDGS protein feed equipment ,feed drying equipment . 3.Waste water environmental process equipment 4.Design and manufacture ethanol/alcohol equipment according to customers inquired or drawing .
Cassava Alcohol/Ethanol Plant We professional manufacture of ethanol alcohol equipment ,DDGS ,equipment ,vine gare equipment in China. The material can be corn(maize) ,wheat,potato,cassava,molasses,beetroot,or any other material which contains starch or sugar .we sell our products to more than 20 countries all over the world. Now our main products are as follow : 1.Turnkey ethanol /alcohol plant project which can produce 95% -96% food grade alcohol,medical alcohol,reagent grade anhydrous ethanol/alcohol or 99.8% fuel grade anhydrous ethanol .Output can be from 1000LPD to 2million LPD . 2.DDGS protein feed equipment ,feed drying equipment . 3.Waste water environmental process equipment 4.Design and manufacture ethanol/alcohol equipment according to customers inquired or drawing .
Molasses Turnkey Project Alcohol/Ethanol Plant We professional manufacture of ethanol alcohol equipment ,DDGS ,equipment ,vine gare equipment in China. The material can be corn(maize) ,wheat,potato,cassava,molasses,beetroot,or any other material which contains starch or sugar .we sell our products to more than 20 countries all over the world. Now our main products are as follow : 1.Turnkey ethanol /alcohol plant project which can produce 95% -96% food grade alcohol,medical alcohol,reagent grade anhydrous ethanol/alcohol or 99.8% fuel grade anhydrous ethanol .Output can be from 1000LPD to 2million LPD . 2.DDGS protein feed equipment ,feed drying equipment . 3.Waste water environmental process equipment 4.Design and manufacture ethanol/alcohol equipment according to customers inquired or drawing .
Olive Cherry Date seeds Removing Machine Fruit seeds stone Removing machine series fruit different capacity different ,machine are little different ) Apricot kernel remover stone /core removing machine Peach core remover Apricot,Peach,Jujube nut removing machine Red date/Peach and apricot /Green plum / Cherry /Hawthorn /Sandberry /Iraq date /Date de /Marinated peach kernel machine Olive /Li Zi /Nut and butter/Litchi/ Pear stone removing machine Longan /Automatic stone core removal machine of large-scale red date automatic jujube type /Hawthorn / Beach date /Prunus cherry and so on ...about 20-40kind fruit can be stone removing machine Technology advantage : 1. The full-automatic equipment has high degree of automation. The mold conveyor belt can automatically feed and send materials to carry out transportation and core flushing. It only needs to pour the fruit into the feed hopper to complete the separation effect of core and flesh. It can work continuously and solve the problems of low efficiency, labor-consuming and time-consuming of manual core removal. 2. The structure of the machine is composed of stainless steel thick wall square tube and channel steel welding, which makes the equipment more stable during start-up and operation. All parts are assembled with bolts, which makes the operation and maintenance of the equipment more convenient. 3. The raw material of the equipment is made of stainless steel, which meets the hygienic standard of food processing equipment. The conveyor belt is made of imported polyurethane material, which is wear-resistant, tensile, tear resistant and has a longer service life. 4. The operation of the machine is simple and convenient, without long-term care. One person can manage multiple machines at the same time. The transmission system adopts advanced design concept and standardized components. The principle of core punching adopts the process of machine tool to punch the core, so that each equipment meets the high design standard, so that the effect of core removing is good, and the fruit shape is completely unchanged.
2-head packaging machine (also can 4-18head according different capacity choice) Packaging speed 15bags/min Bag length 90-320mm Bag width 80-210mm Overall weight 400kg Power 1.8kw/220v Packaging capacity 20-1000ml Outer packaging size 820 x1220 x 2500mm Packaging form Back sealing This machine is an intelligent weighing automatic quantitative packaging machine with four scales and microcomputer control. Suitable for quantitative packaging of granular materials such as miscellaneous grains, nuts ,pesticides, fertilizers, veterinary drugs, premixes, additives, laundry detergent, salt, monosodium glutamate, white sugar, seeds, rice, snacks, hardware, etc. Performance characteristics: 1. High precision digital sensors enable precise measurement to be achieved instantly. 2. The microcomputer control system is technologically advanced, easy to operate, and more reliable to use. 3. Fast and slow vibration feeding, automatic correction of errors, achieving high-precision packaging. 4. Four scales work alternately, with fast packaging speed. 5. High quality stainless steel is used for the material contact part, which is anti-corrosion, dust-proof, and easy to clean. Host configuration: This machine is equipped with a dual CPU microcomputer control system, a 5-inch LCD display in Chinese or English, a user-friendly operation interface, automatic cursor detection and tracking, and simpler operation. Equipped with high-precision stepper motors to ensure the accuracy of the cutting position of each packaging bag.
2Lians Recycling Pte Ltd can supply below scrap product: Pet Food Tray Flake Natural Plastic Scrap MATERIAL: Pet Food Tray Flake Natural CATEGORY: PET TYPE: Flake GRADE: Sheet SPECIFICATION: IV: 0.4-0.6; Post-Industrial ORIGIN: Japan LOADING WEIGHT: 20 Tons FOB (USD/Ton): 600-750
