Multiple Protections:  Dry run protection Phase loss protection Overload/no load protection Short circuit protection Over-voltage protection Pump stalled/antiseizing protection Undervoltage protection Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
Multiple Protections:  Dry run protection  Phase loss protection Overload/no load protection  Short circuit protection Over-voltage protection  Pump stalled/antiseizing protection Undervoltage protection  Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
Multiple Protections Dry run protection Phase loss protection âOverload/no load protection â? Short circuit protection â? Over-voltage protection â? Pump stalled/antiseizing protection â? Undervoltage protection â? Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
1. Product Performance As an indispensable part of the hydraulic system, the performance of the hydraulic hose is directly related to the stability and safety of the entire system. Our hydraulic hose has the following excellent performance: High-pressure resistance: Made of high-strength materials, it can withstand extremely high working pressure and ensure stability and reliability under high-pressure environment. Oil-resistant and corrosion-resistant: The inner wall is smooth and made of oil-resistant and corrosion-resistant materials, which can effectively resist the erosion of hydraulic oil and other media and extend the service life. Soft and flexible: The hose has good softness and flexibility, is easy to install and arrange, and can adapt to various complex working environments. Good sealing: Advanced sealing technology is used to ensure that the hose has no leakage at the connection to ensure the normal operation of the hydraulic system. Anti-aging: After special treatment, the hose has excellent anti-aging performance and can maintain a long service life even in harsh environments. 2. Product scope of application Hydraulic hoses are widely used in the following fields: Engineering machinery: hydraulic systems of engineering machinery such as excavators, loaders, and rollers. Metallurgical equipment: hydraulic systems of metallurgical equipment such as steel and non-ferrous metals. Petrochemical: hydraulic systems of petrochemical industries such as oil fields, refineries, and chemical plants. Agricultural machinery: hydraulic systems of agricultural machinery such as tractors and harvesters. Shipbuilding industry: hydraulic systems of ships and offshore platforms. 3. Reasons to choose us Excellent quality: We strictly control the procurement of raw materials and the production process to ensure that each hydraulic hose meets high quality standards and can provide customers with stable and reliable products. Leading technology: We have a professional R&D team and advanced production equipment, and continuously launch new and high-performance hydraulic hose products to meet the ever-changing market and customer needs. Thoughtful service: We provide a full range of pre-sales, in-sales and after-sales services, including technical consultation, product selection, installation and commissioning, maintenance, etc., to ensure that customers receive timely and professional support during the purchase and use process. Reasonable price: On the premise of ensuring quality and leading technology, we provide reasonable prices to ensure that customers obtain cost-effective products and services. Brand reputation: We have been committed to building a well-known brand. With years of market accumulation and word-of-mouth effect, we have won the trust and recognition of our customers. Choosing us means choosing peace of mind and trust.
Payments:T/T, Western Union Delivery:2days for stock,OEM about 3-5weeks Origin:CHINA Packing:optical package Inspection:IL Samples:Charge Sample Price:$0.10 Remarks:www.unitedphtech.com United Photonics Technology UPT provides many kinds of high precision prisms, including Penta Prism, Beamsplitter Penta Prism, Right Angle Prism, and Corner Cube. Our micro Penta Prism and Right Angle Prism are widely used in optical communication, such as optical switches. Other kinds of prisms, such as Dove Prism and Roof Prism are also available upon request.product image Penta Prisms Penta prism can deviate an incident beam without inverting or reversing to 90.The deviation angle of 90 is independent of any rotation of the prism about an axis parallel to the line of intersection o.. Read more product image Beamsplitter Penta Prism By adding a wedge and with partial reflective coating on first reflective surface, Penta Prism can be used as Beamsplitter.We supply Beamsplitter Penta Prism with standard Transmission/reflection (T/R.. Read more product image Wedge wedge prism can be used to bend a laser beam to a set angle. In tandem, these prisms can serve as an anamorphic pair for correcting the elliptical shape of diode outputs or steering a beam anywhere wi.. Read more product image Right Angle Prisms A right-angle prism is used as a mirror to deviate light through 90 degrees and also as a reflector to deflect light through 180 degrees by total internal reflection. Applications: Imaging Optical S.. Corner Cube Retroreflectors Corner Cube Prism is also called Retroreflector or Trihedral Prism. In the Corner Cube Prism, three reflecting surfaces are perpendicular to each other, like the side wall of the cube. The input surfa.. Read more product image Anamorphic Prisms With a anamorphic prism, the beam size can be changed along the axis while leaving the beam unchanged along the other axis, so the beam can be expanded, reduced or reshaped. Anamorphic prisms are use.. Read more product image Dove Prisms The Dove Prism is also called Image Rotator. The prism rotates the image without changing the direction of the input beam, which is parallel to hypotenuse. Rotation of the prisms in relation to the su.. Rhomboid Prisms Rhomboid prisms (off-set prism) are commonly used to displace a laser beam without changing its direction. In imaging applications, rhomboid prisms will displace the optical axis without inverting the.. Read more Reflection Prism The reflection prisms are usually used for diverging the ray or for changing image location in relation to the subject (rotation, inversion). All the surfaces of the reflection prisms are flat. Reflec..
Xiongcai Motor Controller XCA107 Designed For Automotive Engine Cooling 1. Voltage DC16~36V 2. Rated Current 4.6A 3. Working Temp -40 125 4. Working Humidity 95% 5. Size: 61*56*17mm 6. Protection under voltage, over voltage, low temperature, over temperature, plugging, reverse connection, short circuit 7. PWM speed regulation Established in 2011, founded by experienced engineer, XIONGCAI TECH is a pioneer in specialized field of motor controller (electronic speed control or ESC), especially in water pump for auto engine cooling. Xiongcai had engineered a motor controller for automotive engine cooling---XCA107, which has been using in automotive engine for years. ACHR, a company rooted in automotive water pump for decades, contacted us and inquired about motor controller for automotive water pump. The client was really picky and particular, their engineer team set a standard on protection measure beyond the industry. They said they had met several suppliers, some items of the standards were unacceptable, because if all items met this extremely high standard, the cost would exceed cost budget. Xiongcai team wanted to give a shot. Engineered from ground up, Xiongcai R&D team designed a combination of software and hardware meticulously called XCC107, making all parameters up to customers standard. After one year test and verification, Xiongcai XCA107 motor controller for water pump was approved. The client has introduced this product for several years till now. Xiongcai XCA107 Motor Controller for water pump provides protection measures including under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit, this means the motor controller may stop working due to some reason but never be damaged. We are one of the few engineering companies providing a full service from design to supply of product, which means we design, analyze, test and supply finished products. Xiongcai motor controllers have been applied to many top brands in auto industries, such as Jingyi Group, ACHR, FAW Group, FAWDE, Shenhai Electrical Appliances, Kesen, Cummins and more. Contact us Shenzhen Xiongcai Technology Co., Ltd for more detail, we deliver excellent solution to you.
Xiongcai Water Pump Motor Controller Approved by The Biggest Water Pump Manufacturer In China. 1. Voltage DC16~36V 2. Rated Current 4.6A 3. Working Temp -40 125 4. Working Humidity 95% 5. Size: 61*56*17mm 6. Protection under voltage, over voltage, low temperature, over temperature, plugging, reverse connection, short circuit 7. PWM speed regulation Xiongcai Technology has been specializing in motor controller since 2011, we engineer, analyze, test and supply finished products. At present, in China, most of manufacturers provide OEM service only, they don�¢??t support you in technology, but just provide OEM. We serve you from initial concept to product supply. Unicent Automotive Tech, a company focused in automotive thermal management, contacted us and inquired ab out motor controller for automotive water pump. They have high requirements on reliability, performance and safety. They said they had met several suppliers, some items of the standards were unacceptable, because if all items met this extremely high standard, the cost would exceed budget. Xiongcai team wanted to give a shot. R&D team designed a potent combination of software and hardware meticulously, called XCA107 with power system of 4.6A, DC16-36V, making parameters up to the customer's requirements. After one year test and verification, XCA107 motor controller for water pump was approved. The client has introduced this product for 4 years till now. XCA107 Motor Controller For water pump provides protection measures including under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit. That means this product would stop when the protection measure is triggered, but never be damaged. Furthermore, this product is certified by CSIPER25, ISO11452-2, ISO10605, ISO16750, ISO7637. You don�¢??t need to worry about the reliability. We are one of the few engineering companies providing a full service from design to supply, and serving top clients in auto industries, such as NISSAN, XPeng, Jingyi Group, Risun, FAW Group, FAWDE, Feilong Auto(FLACC), Keshen, Unicent and more.
Xiongcai Motor Controller Applied In Cummins Engine 1. Voltage DC16~36V 2. Rated Current 10A 3. Working Tempï¼?-40ï½?85â?? 4. Working Humidityï¼?95% 5. Size: 87*84*15mm 6. Protectionï¼?under voltage, over voltage, low temperature, over temperature, plugging, reverse connection, short circuit 7. PWM speed regulation Since 2011, Xiongcai Technology has been a pioneering company in specialized field of motor controller for automotive Fuel Pump. Founded by experienced engineer, Xiongcai tends to be at the leading edge of technological development of motor controller for automotive fuel pump. In 2018, Joinhands Auto Parts, a company specialized in design and manufacture of automotive fuel pump, contacted us and inquired about motor controller for their products. The client was really picky and particular, their engineer team set a standard on protection measure beyond the industry because this product is designed for Wuhan Cummins, one of greatest engine manufacturers in China. They said they had met several suppliers, some items of the standards were unacceptable, because if all items met this extremely high standard, the cost would exceed budget. Xiongcai team evaluated the requirements and decided to have a try. Engineered from ground up, Xiongcai R&D team designed a combination of software and hardware meticulously called XCA105, making all parameters up to customer�¢??s standard. After one year test and verification, Xiongcai XCA105 motor controller for fuel pump was approved. The client has introduced this product for 6 years till now. Xiongcai XCA105 motor controller for fuel pump with 8A current, DC8-18v power system, working humidity 95% max, providing protection including under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit protection. And this product certified by CSIPER25, ISO11452-2, ISO10605, ISO16750, ISO7637. XCA105 motor controller is a trusted product and Xiongcai is a trusted partner. We are one of the few engineering companies providing a full service from design to supply of product, which means we design, analyze, test and supply finished products. Xiongcai is partnering with top clients in auto industries, Jingyi Group, Risun, FAW Group, FAWDE, Feilong Auto(FLACC), Keshen, Unicent and more.
Xiongcai Motor Controller Approved By The Largest Auto Group In China 1. Voltageï¼?DC16~36V 2. Rated Currentï¼?10A 3. Working Tempï¼?-40ï½?85â?? 4. Working Humidityï¼?95% 5. Size: 87*84*15mm 6. Protectionï¼?under voltage, over voltage, low temperature, over temperature, plugging, reverse connection, short circuit 7. PWM speed regulation Since 2011, Xiongcai Technology has been a pioneering company in specialized field of motor controller for automotive Fuel Pump. Founded by experienced engineer, XIONGCAI TECH is one of the few manufacturers that focus on motor controller (electronic speed control or ESC), especially in automotive fuel pump. We launched a motor controller XCA105 which was engineered for automotive fuel pump. In 2016, Keshen Auto Parts, a company specialized in design and manufacture of automotive fuel pump, contacted us and inquired about motor controller for their products. The client was really picky and particular, their engineer team set a standard on protection measure beyond the industry because this product is designed for the greatest automobile group in China�¢??FAW. They said they had met several suppliers and discussed the requirements, some items on the list were really hard to achieve at the same time, because if all items met this extremely high standard, the cost would exceed cost budget. Our RD team evaluated the list and decided to take this project. R&D team designed a combination of software and hardware meticulously called XCA105, making all parameters up to customer�¢??s standard. After one year test and verification, Xiongcai XCA105 motor controller for fuel pump was approved. The client has introduced this product for 6 years till now. Xiongcai XCA105 motor controller for automotive fuel pump provides protection measures including under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit protection, this means the motor controller may stop working due to some reason but never be damaged. We are one of the few engineering companies providing a full service from design to supply of product, which means we design, analyze, test and supply finished products. The company is serving top clients in auto industries, Jingyi Group, Risun, FAW Group, FAWDE, Feilong Auto(FLACC), Keshen, Unicent and more. Contact us Shenzhen Xiongcai Technology Co., Ltd for detail. We try to assist you in achieving your idea.
Xiongcai Motor Controller Has Been Introduced By The Largest Auto Fuel Pump Manufacturer 1. Voltage DC16~36V 2. Rated Current 10A 3. Working Temp -40 85 4. Working Humidity 95% 5. Size: 87*84*15mm 6. Protection under voltage, over voltage, low temperature, over temperature, plugging, reverse connection, short circuit 7. PWM speed regulation Xiongcai Technology tends to be at the leading edge of technological development of motor controller for automotive Fuel Pump. XIONGCAI TECH is one of the few manufacturers that focus on motor controller (electronic speed control or ESC) only, especially for automotive fuel pump. In 2017, ACHR Electrical Machinery, a company specialized in design and manufacture of automotive fuel pump. They contacted us and inquired about motor controller for their products. The client was really picky and particular, their engineer team set a standard on protection measure beyond the industry because this product is designed for the greatest automobile engine group in China�¢??FAWDE. They said they had met several suppliers, some items of the standards were unacceptable, because if all items met this extremely high standard, the cost would exceed cost budget. Xiongcai team wanted to give a shot. Xiongcai R&D team designed a combination of software and hardware meticulously called XCA105, making all parameters up to customer�¢??s standard. After one year test and verification, Xiongcai XCA105 motor controller for fuel pump was approved. The client has introduced this product for 6 years till now. Xiongcai RD team designed perfect protection measures to protect the motor. a. Peak current limit. This measure will limit the peak current to avoid damage to motor; b. Single PWM periodical current detection limit reduces impact of pulse current to motor; c. Waterproof is designed for all weather condition, up to IP67. The ESC is potted in epoxy to protect the electronics and improve heat transfer, enabling motor controller working in any condition at a lower temperature; And more protection measures including under voltage, over voltage, over current, low temperature, over temperature, plugging, reverse connection, short circuit protection. Furthermore, XCA105 motor controller was certified by CSIPER25, ISO11452-2, ISO10605, ISO16750, ISO7637. We are one of the few engineering companies providing a full service from design to supply of product, including design, analyze, test and supply finished products. Xiongcai is serving top clients in auto industries, ACHR, Jingyi Group, Risun, FAW Group, FAWDE, Feilong Auto(FLACC), Keshen, Unicent and more. Contact us Shenzhen Xiongcai Technology Co., Ltd for detail. We try to assist you in achieving your idea.
Our silicone hose are widely used in VOLVO, Scania , KAMAZ, CUMMINS, IVECO, DAF, MAN, and Chinese heavy trucks and cars. And we could manufacture as your samples and drawings. 1. What are the advantages of our silicone hose ? 1). Real factory, brand silicome raw material to get preferential price. 2). Experienced technician to g uarantee hose quality. 3). OEM &ODM hose is welcome. 4). Good aftersales service. 5). Customer's logo is acceptable. 2. What are the Specific Details of our silicone hose? Materialï Silicone Engine Air SupplyExhaust pipe Working temperature- 6 0°C ~+2 2 0°C Support Pressure0.3 to 0.9MPa Explosive Pressure 0.5-0.9 MPa Crankand & CamshaftBreather Hose Hardness35~80 shore A Engine Cooling SystemRadiator Hose Thickness2mm ~ 5mm Diameter Range3mm~50mm or as request Color optionsblue,black,red, orange Or custom colors Size tolerance+/- 0.5mm Reinforcement1~2layers of polyester 3.Why choose silicone hose? A. Bear high pressure (Explosive Pressure 5.5~9.7MPa) B. Bear high temperature(-50 ~ 260 °C ) C. Corrosion resistance D. Ageing resistance E. Longer operating life than EPDM (More than 1 year at least ) FAQ 1. How can I get a sample to check your quality? A: After price confirmation, you could require for sample to check our quality. Universal hose sample is free, but freight has to be afford by buyer. 2. Can you print our company's logo on hose? A: Yes, we can print your logo if you could provide us with copyright and letter of authority. 3. Can you custom silicone hose or rubber hose? A: Yes, we are professional factory to produce all kinds of silicone hose and rubber hose. You just need tell us the specification size you need (drawing will be the best.), then we will assist to produce hose you need. 4. After my payment, How about the delivery time? A: Normally, we will take about 15-30 days to produce the order. For small order (less than 200 pieces), we will need 15 days to produce hoses.
Flat Sheet Ceramic Membrane The flat plate membrane is a new type of high temperature plate porous ceramic membrane, which is prepared by high temperature sintering process using inorganic materials such as alumina. Our Ceramic flat sheet membrane can offer exceptional efficiency and durability compared with the organic film. Ceramic flat membrane produced by one of professional flat sheet membrane manufacturers in China has the advantages of good chemical stability, good reliability, long service life and strong anti-pollution ability. Advantages of Flat Sheet Ceramic Membrane Long life and no degradation Strong resistance to acid, alkali and to organic solvent; Suitable for all kinds of wastewater containing solvents and chemicals Strong hydrophilic and better anti- pollution property Better Mechanical properties, no broken wires phenomenon of hollow fiber membrane Easy to wash lower cleaning frequency, suitable for all kinds of membrane cleaning methods Low operating cost and energy saving Flat Sheet Ceramic Membrane Specification Length (mm) 500-1100 Width (mm) 110, 150, 250 Thickness (mmï¼? 3, 6 Area (m2) 0.5 Membrane material Al2O3, ZrO2, TiO2 Pore diameter (�¼m) 0.1 Pure water flux (m3/m2.h) 0.5-1.0 pH 0-14 Breaking strength (MPa) 40 Ceramic Flat Sheet Membrane Application Area Membrane Bioreactor (MBR) Industrial wastewater treatment (e.g. paper mill wastewater treatment) Seawater desalination pretreatment Municipal wastewater treatment Domestic sewage treatment Hospital wastewater treatment Landfill leachate treatment Pretreatment of RO system
Digital Rail Head Wear Gauge is is mainly used to measure the vertical wear and lateral wear of the rail. The reasonable design makes it light, convenient operation and intuitive reading. FEATURE 1. Digital type with direct readings: LCD display screen, clear and readable; No calculations required, gives direct reading ; When reading, hold down the HOLD button to fix the measurement value and facilitate reading. 2. High measuring accuracy : The measurement accuracy is 0.01m 3. Easy to use, measure the vertical and lateral rail wear at the same time, Position the rail wear gauge on the outer side of the rail . Push the vertical and lateral rail wear gauge so that the measuring probe is in contact with the upper surface and inner side of the rail respectively. Then the vertical and lateral wear of the rail can be read. 4. Metric /imperial unit 5. Support customize: We could customize all kinds wear gauge according to different rail profiles and different measure points. 6.Fast calibrate: One-key zero clearing function, can be quickly calibrated before each use to reach the factory measurement accuracy. 7. Magnetic fixed part: Strong magnetic fixed part to attach to the rail. 8. Rail fillet as measuring base to ensure measure data more accuracy Rail fillet is more clear than rail bottom, no dust. It could ensure the measure result reliability. 9. Portable Handle : This product is designed with a handle that is easy to hold, which greatly improves the portability of the product. It can avoid touching the ruler body directly, cause the ruler body to be stained and corroded, improve the product service life. Model LJ-GM-A Center vertical wear measure range0-15mm Lateral wear measure range0-25mm Score value0.1mm Indication error ± 0. 15mm Supply CustomizeUIC60/60E1, UIC54 /54E1, 115RE 68TR ect all profiles Block customize block for gauge
PRODUCT DESCRIPTION High Durable Excavator Thumb Bucket Hydraulic Grab Bucket Hydraulic Thumb Bucket Description Also Known as Thumb Bucket, Clamp Bucket, It Mainly Applies for Recycling / Civil Applications. Clamp Bucket Specification Weight kg 180 360 520 840 1430 1860 Max Opening mm 818 1150 1380 1550 2220 2235 Oil Pressure kg/m^2 100-130 110-140 120-160 150-170 160-180 160-180 Operating Oil L/min 25-40 30-55 50-100 90-110 100-140 130-170 Cylinder Volume ton 4 5.4 5.4 8.2 10 12 Suitable Excavator ton 2~3 4~6 7~11 12~16 17~23 24~30 * The Parameter above may change with the technology improvement, will not notice additionally, please understand. * For other diameters and lengths, we can customize service, OEM/ODM Thumb Bucket Features 1. Rotary Type High Durable Q345B Steel Excavator Buckets Toosan Digger Hydraulic Thumb 0 2. Fixed Type: High Durable Q345B Steel Excavator Buckets Toosan Digger Hydraulic Thumb 1 Clamp Bucket Real Work shot High Durable Q345B Steel Excavator Buckets Toosan Digger Hydraulic Thumb 2 Excavator Integrated Thumb Bucket Can be used for disposable waste, shrubs, logs, construction waste, stones, pipes, landscaping materials, and demolition sites.Hydraulic excavator grab disassembly and recovery/civil applications. The thumb bucket has advantages in grasping small pieces of wood, sticks, and strips. Suitable for municipal construction, secondary demolition, mining, and most of the operating environment. Easily handle all types of loose, irregularly shaped objects encountered in demolition, industrial, construction, recycling, storm debris removal, landscaping, and other tough job applications.
Rail Profile Gauge Rail Profile Gauge is is mainly used to measure the vertical wear and lateral wear of the railThe reasonable design makes it lightconvenient operation and intuitive reading Features 1 Digital type with direct readings LCD display screen clear and readable No calculations requiredgives direct reading When reading hold down the HOLD button to fix the measurement value and facilitate reading 2 High measuring accuracy The measurement accuracy is 001m 3 Easy to use measure the vertical and lateral rail wear at the same time Position the rail wear gauge on the outer side of the rail Push the vertical and lateral rail wear gauge so that the measuring probe is in contact with the upper surface and inner side of the rail respectivelyThen the vertical and lateral wear of the rail can be read 4 Metric imperial unit 5 Support customize We could customize all kinds wear gauge according to different rail profiles and different measure points 6Fast calibrate Onekey zero clearing function can be quickly calibrated before each use to reach the factory measurement accuracy 7 Magnetic fixed part Strong magnetic fixed part to attach to the rail 8 Rail fillet as measuring base to ensure measure data more accuracy Rail fillet is more clear than rail bottomno dust It could ensure the measure result reliability 9 Portable Handle This product is designed with a handle that is easy to hold which greatly improves the portability of the product It can avoid touching the ruler body directly cause the ruler body to be stained and corroded improve the product service life Model LJGMA Center vertical wear measure range 015mm Lateral wear measure range 025mm Score value 01mm Indication error 0 15mm Supply Customize UIC6060E1 UIC54 54E1 115RE 68TR ect all profiles Block customize block for gauge
RB 1530 portable CNC plasma flame cutting machine has two working modes: plasma cutting, and (flame) gas cutting. Usually plasma cutting machines are used for thickness less than 30mm metal cutting. The gas (flame) cutting machines are used for thickness 30-200mm iron/ steel cutting. Portable CNC plasma flame cutting machine features 1. Two cutting modes optional: plasma cutting and gas (flame) cutting. 2. This CNC plasma cutting machine moves by high precision gear and rack ,accurate running in high speed. 3. The operation is simple, fast, easy to learn the programming software. 4. Small cutting loss and typesetting software high material utilization. 5. Read U disk files through USB directly, convenient site operation. 6. The machine also has feature that automatic arc voltage torch height control, it can adjust cutting distance automatically. 7. It is easy to move, suitable for the site indoor or outdoor 8. Can automatically memorize and restore when power is off. Portable CNC plasma flame cutting machine parameters: Model RB-1530 Working Voltage AC 220V/380V, 50HZ Cutting Size 1500mm*3000mm Plasma Cutting Thickness 0-30mm,According to different power source Gas(flame) cutting Thickness 1-200mm Weight 230KGS Control System STARFIRE(FANGLING optional) Driving System LEADSHINE stepper motor Transmission Method Gear transmission Power Supplier HUAYUAN power or US HYPERTHERM Guide Rail Round rails Nesting Software FASTCAM
Model features: This series of models is an open aluminum alloy profile structure heat shrink baking machine, suitable for electronic wire harness and new energy wire harness heat shrink tubes, circuit boards, inductor wire diagrams, copper bars, hardware accessories and other products (heat shrink baking size range small, but the product size is relatively long), or products that can only be heat-shrunk and baked at one end. 1. The machine uses far-infrared heating tubes for heating (the new energy wiring harness uses thermal radiation heat shrinkable tubes). There are heating tubes installed on the top, bottom, left and right, which can be heated at the same time. It is also equipped with a high-speed centrifugal fan, which can Stir the heat evenly to keep the entire box at a constant temperature; the products that need to be heat-shrunk and baked can be heated at the same time, maintaining the original characteristics of the product, so that the product does not deform or discolor after heat-shrinking or baking, and the quality Stablize: 2. Use high-temperature resistant Teflon mesh belt (temperature resistant 0-350), feeding in assembly line mode, fast baking speed and high efficiency: 3. Aluminum alloy profile structure mode, the mechanical size and structure can be customized and modified at will, and the machine model has a compact structure and exquisite design, and can also be moved and connected to the production line and controlled synchronously; 4. Intelligent control system, the heating temperature and speed can be adjusted at will, which can adapt to the temperature and heat shrinking time needs of different products; 5. Independent control electric box, away from high temperatures; the double-layer design of the heating box is sandwiched with high-temperature insulation cotton (temperature resistance 1200�°C), so that the surface temperature of the box will not be overheated, which not only makes the working environment comfortable, but also reduces Energy waste.
Product Description Specifications Quarter Package: PU with Revel IX Technology Elite-level stiffness and responsiveness for higher-end hockey IX Tech provides a more anatomical, performance-focused fit with the new injection construction process Flexible tendon guard, forward boot rake (or lean) and toe spring all help promote the ideal roller hockey stride Heat moldable for a custom fit and reduced break-in time Comfort Edge collar padding to alleviate ankle irritation Liner: Brushed Tricot for comfort, moisture-management and durability Tongue Construction: Two-piece, Vented Pro Felt Thick design protects the top of the foot from impacts and lace-bite Ventilated center to promote consistent airflow Outsole: Stiff TPR Plastic with Composite Overlay Delivers a perfect balance of lateral support and forgiveness Frame: One-Piece, Alkali Rize Aluminum Chassis Larger rear wheels with smaller front wheels increase agility without compromising top-end speed Fully extruded with 6000-series aluminum for optimal strength and less weight Sizes 1.0-3.0 /(2) 59mm in the front and (2) 68mm in the rear Sizes 4.0-5.0 /(2) 68mm in the front and (2) 72mm in the rear Sizes 6.0-13.0 /(2) 76mm in the front and (2) 80mm in the rear Alkali Square Flush Two-Piece 6mm Axles Wheels: Konixx Tachyon (+0) Indoor Wheels U-base 3 Formula withTrac-tech, Infini-tech andVeloci-tech additives Specially designed hub and dinner core for optimum performance Revel Xena 74A Indoor Wheels Bearings: Helo Swiss 608 Bearings Skate Width:D Weight: 1,346 grams (Size 9)
Features: 1) Beautiful The remote control robot chassis is beautiful in appearance. The fuselage is large, and the space reserved for development is sufficient. 2) Strong The bottom of the fuselage is reinforced to carry heavy loads. The installation position of the travel motor has also been reinforced to prevent deformation and displacement. The tires are lawn tires with a width of 15cm, which are beautiful, durable, large in width and strong in support. 3) Mature technology This product is modified on the basis of our very mature remote control lawn mower, an economical chassis product. It adopts the mature walking motor controller on our remote control lawn mower, which has the characteristics of sensitive response and fast response speed. The built-in smart chip can intelligently detect the current and heating conditions, which can ensure stable use all year round. And it has a slow start function, the operation is smooth, and there will be no frustration when accelerating or decelerating suddenly. 4) Scalability Equipped with a function expansion HUB, which can control additional 4 channels, it can easily control and expand other functions required by customers without professional remote control knowledge. On the basis of our chassis, you can freely add other functional modules to create a new vehicle that meets your own needs. Specification: Walking Speed: 0-6km/h Working Temperature: -20~55�° Remote Control Range: 200m Walking Motor Motor Type: Brush electric traction Voltage / Power: 24V / 350W Reduction Ratioï¼?23.2:1 Rotating Speed: 75RPM Rated/Max Output Torque: 18.4/55Nm Wheel: 15X6.00-6 vacuum tire Battery: 24V 20Ah Remote Control Channel: 7 Extended Controllable Channel: 4 Payload: 50~300kg Wheelbase: 810mm Track: 890mm Overlay Panel: 990*625mm Machine Size: 1070*1035*430mm Machine Weight: 98kg Package Size: 1150*1120*600mm Gross Weight: 130kg
Do you want to spend less time aerating and more time enjoying your lawn? The BlueBird TA10 has a wide width of 36" to let you aerate more land in less time. Two independent tine rotors which have 32 interchangeable closed spoon tines give you an aerating width of 36 which allows you to aerate large areas quickly. Optional weight containers can be purchased to add extra weight for optimal soil penetration. Maneuver around tight areas and corners with ease thanks to the dual tine rotors. Plus the unique side wheel system also adds to the maneuverability by allowing the aerator to move through tight passages and also allows it to be stored on its side. Tow Behind Aerator:No engine to worry about! Just be sure to use a tractor with an engine that is 16HP or larger to tow this aerator. Wide Aerating Width:36 of aerating width allows you to cover large areas in less time Adjustable Aerating Depth:Aerate from 0-3 for precise and consistent coring 40 Interchangeable Closed Spoon Tines:4.4 x 6 tine pattern Unique Side Wheel System:Allows aerator to easily move through tight passages without getting hung up and also allows for the aerator to be safely stored on its side. Optional Weight Containers (Sold Separately):Add up to 5 weight containers to add additional weight to ensure optimal soil penetration.
