Socket Weld Gate Valve Main features * Bolted body-bonnet design for valves up to Class 800, 1500, 2500, 4500. Valves with welded bonnet also available on request * Screwed with a seal-welded body-bonnet design for valves of Class 1500,2500, 4500. * Bellows-sealed Gate and Globe valves available in Class 800 * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
SQK A182 F304L Stainless Steel Gate Valve Main features * Bolted body-bonnet design for valves up to Class 800, 1500, 2500, 4500. Valves with welded bonnet also available on request â * Screwed with a seal-welded body-bonnet design for valves of Class 1500,2500, 4500. * Bellows-sealed Gate and Globe valves available in Class 800 * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
A182 F321 Stainless Steel Gate Valve Main features * Bolted body-bonnet design for valves up to Class 800, 1500, 2500, 4500. Valves with welded bonnet also available on request * Screwed with a seal-welded body-bonnet design for valves of Class 1500,2500, 4500. * Bellows-sealed Gate and Globe valves available in Class 800 * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
A182 F321H Stainless Steel Gate Valve Main features * Bolted body-bonnet design for valves up to Class 800, 1500, 2500, 4500. Valves with welded bonnet also available on request * Screwed with a seal-welded body-bonnet design for valves of Class 1500,2500, 4500. * Bellows-sealed Gate and Globe valves available in Class 800 * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
A182 F51 Duplex Stainless Steel Gate Valve Main features * Bolted body-bonnet design for valves up to Class 800, 1500, 2500, 4500. Valves with welded bonnet also available on request * Screwed with a seal-welded body-bonnet design for valves of Class 1500,2500, 4500. * Bellows-sealed Gate and Globe valves available in Class 800 * Bolted body-bonnet joints provided with spiral-wound stainless steel gasket and graphite filler for maximum protection against leaks * Die-formed graphite inner packing rings and braided graphite end rings with Inconel wire reinforcement and corrosion inhibitor * T-head stem-disc connection of gate valve fully meets strength requirements of API 602 and API 598 * Rolled ACME thread on stem for smooth operation * Tapered shoulder on the stem for back seating * Self-aligning type gland assembly with stud-and-nut tightening * Integral hard-faced body seat for globe and check valves * Spring-loaded disc on check valves suitable for no horizontal applications too * Gate and globe valves can be offered with electrical actuators * Austenitic SS forging for body and bonnet of Cryogenic valves, resulting in excellent impact strength, minimal heat loss and resistance to corrosion * Valves can be offered to NACE MR-0175 and other special NACE requirements
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing �¢?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size �¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing â?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing �¢?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size �¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing �¢?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size �¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing �¢?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size �¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
* We manufacture a wide range of Process Ball Valves in single, two, and three-piece constructions.The valves are available in full-bore and regular-bore designs, in a variety of end connections and materials to suit customer requirements. * The valves are of floating-ball design where the ball moves towards the downstream seat, under pressure, to effect a tight seal.Trunnion-mounted Ball Valve design complies to API 6D * Wide portfolio of Side-entry and Top-entry designs * Fugitive emissions - Soft and Metal seated valves complies to ISO 15848-1, Class AH and BH * Firesafe design - to API 607 and API 6FA * CE Marking - Meets requirements of Pressure Equipment Directive 2014/68/EU, Pneumatic shell test conducted at 1.1 times rated pressure to check shell integrity, when required * Double block and bleed (DBB) feature - Valves are designed and tested for automatic * cavity relief * Anti-blowout stem design * Coil springs used for consistent seat loading and lower operating torque * Lip seals provided for low temperature services * Primary O ring and Secondary graphite (in 3 stage stem, thrust washer is primary) * Wide portfolio of Side-entry and Top-entry designs * Options: Buried service, Cryogenic * Offered with Electric, Pneumatic and Hydraulic Actuators * In-house Tests Capabilities * Fire-safe to ISO 10497 and API 607 * Mirror-finished solid stainless ball * Fine-grained PTFE seats * Cavity Pressure Relief mechanism * Blowout-proof stem * High integrity stem sealing �¢?? Belleville springs compensate for wear and thermal expansions * Size 2" to 56" (50 mm to 1400 mm) * ASME Class Class 150 to 2500 * Design Standard API 6D * Size ¼" to 8" (8 mm to 200 mm) * ASME Class Class 150 to 2500 * Design Standard ISO 17292, API 608, API 6D * Antistatic feature * Actuator-mounting flange conforms to ISO 5211 * Single, two and three piece constructions * Full-bore and regular-bore designs * Soft and metal-seated * Offered in carbon steel, stainless steel and duplex stainless steels * Screwed, socket-weld and flanged ends * ASME classes up to 2500 * Variety of actuation option
A gate valve is generally used to completely shut off fluid flow or, in the fully open position, provide full flow in a pipeline. Thus it is used either in the fully closed or fully open positions. A gate valve consists of a valve body, seat and disc, a spindle, gland, and a wheel for operating the valve. A gate valve can be defined as a type of valve that used a gate or wedge type disk and the disk moves perpendicular to flow to start or stop the fluid flow in piping. A gate valve is the most common type of valve that used in any process plant. It is a linear motion valve used to start or stop fluid flow. Therefore, there is little pressure drop or flow restriction through the valve. Gate valves are used in many industrial applications including the oil and gas industry, pharmaceuticals, manufacturing, automotive, and marine. Gate valves are not suitable for throttling purposes.
Needle valves are usually used in flow-metering applications, especially when a constant, calibrated, low flow rate must be maintained for some time, such as the idle fuel flow in a carburetor. Needle valves sometimes referred to as plunger valves. A needle valve has a relatively small orifice with a long, tapered seat, and a needle-shaped plunger on the end of a screw, which exactly fits the seat. These needle valves are an ideal option for isolating or throttling applications. The self centering, non rotating stem ensures perfect seating. The rigid design gives repetitive bubble tight shut off, easy.s. Our range of needle valves has been designed with durability and performance in the spotlight. These needle valves are available in a variety of sizes (1/4, ½, 1/8 inch). Our range of needle valves has been designed with durability and performance in the spotlight. These needle valves are available in a variety of sizes (1/4, ½, 1/8 inch).