Freezing Of Slurry Pump Suppliers and Manufacturers

Introduction: Series lmhh slurry pumps are cantilevered, horizontal and centrifugal. The main feature of this series is to transport the slurry for high pressure. Because of its high speed, only metal lined pump could meet the design requirements and the rubber not. Structure: the wet parts of lmhh pump are made of wear-resistant alloy. The shaft seals for series lmhh may be packing seal and expeller seal. The discharge side can be oriented to any of the eight positions to suit installations and applications. Application: they are designed for the handling of highly abrasive, high density slurries in the metallurgical, mining, coal, power generation, construction material and other industry. The pumps could be also installed in multistage series for long delivery Packing: plywood case

Introduction: As the sump pump, series lm(r)s pumps are of single casing and made of wear-resistant metal and natural rubber. The wear parts are made of high chromium for series lms and are rubber lined for series lrs. According to liquid level of the slurry pool, the vertical slurry pump transmission shaft and suction pipe could be chosen for different length. This sump pump could operate under the best condition with different speeds. Application: The vertical slurry pumps are designed to transport the abrasive, large particle and high-density slurries and applied over the fields such as metallurgy, mining, chemistry, coal washery, power plant, building materials and environmental protection.

Application and features: Type ms, hs and hhs pumps are cantilevered, horizontal, centrifugal slurry pumps. They are designed for handling abrasive, high density slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc. The pumps of this type also may be installed in multistage series. The frame plates for type ms, hs pumps are made of interchangeable, hard metal or pressure moulded elastomer liners. The impellers are made of hard metal or pressure moulded elastomer liners. The frame plate liner and impeller for hhs pump are made of hard metal only. The shaft seal for type ms, hs and hhs pumps is gland seal or centrifugal shaft seal. The discharge branch can be positioned at intervals of 45¡ã by request and oriented to any eight positions to suit installations and applications.

Type vs and vsr pumps are vertical, centrifugal slurry pumps submerged in sump to work. They are designed for delivering abrasive, large particle and high density slurries. These pumps have no need of any shaft seal and sealing water. They can also be operated normally for insufficient suction duties. Wet parts of type vs pump are made of abrasion-resistant metal. All parts of type vsr pump immersed in liquid are lined with rubber outer liner. They are suited to transport non-edge angle abrasive slurry. The type with¡°l¡±is a sump pump of extension shaft series, which is suited for the working condition of deeper level. The guide bearing construction is added to the pump on the basis of the standard pump, so the pump is with both more steady operation and wider application range, but flushing water should be attached to the guide bearing.

Product name THM-3C slurry pump Type THM pump size 4/3 Capacity 86.4-198m3/h Head 9-52m Allowable Max. Power 30kw Speed 1000-2200r/min NPSH 4-6m Introduction Model Explanation and Performance Chart: THM-3C T: Tower pump H: High Concentration M: Metal lined 3: Discharge size (inch) C: Frame type with maximum power Introduction of Slurry Pump ---- THM Series THM Series slurry pump is mainly used for handing strong abrasive, high density slurries and low density, high head slurries in the metallurgical, mining, coal, power, building material and other industrial departments etc. The features of this kind of slurry pump The frame plates of this kind of slurry pump have replaceable wear-resistant metal liners. The impellers are made of wear-resistant metal. The frame plate liner and impeller for THM pump are adoptable of hard metal only. Bearing assembly of this kind of slurry pump use cylindrical structure, adjusting the space between impeller and front liner easily, being removed completely when being repaired. Bearing assembly use grease lubrication. The shaft seal of this kind of slurry pump could use the packing seal, expeller seal and mechanical seal. The discharge branch can be positioned at intervals of 45 degrees by request and oriented to any eight positions to suit installations and applications. Here are the drive types, such as V belt drive, gear reducer drive, fluid coupling drive, and frequency conversion drive devices. Wide performance, good NPSH and high efficiency are main character of these kinds of slurry pump. The pump of this type may be installed in multistage series to meet the delivery for long distance. Main application of this kind of slurry pump This kind of slurry pump mainly applies in coal washer processing, handling with the fine ore and tailings in metal mine, handing combined bottom and fly ash in a thermal power station etc. Pump Model THM Series Impeller Dia. Allowable Max.Power Clear Water Performance Capacity Q Head H(m) Speed n(r/min) Max.Eff. ¦Ç% NPSH (m) m3/h l/s THM-1B 15 12.6-28.8 3.5-8 6-68 1200-3800 40 2-4 152 THM-1.5B 15 32.4-72 9-20 6-58 1200-3200 45 3.5-8 184 THM-2C 30 39.6-86.4 11-24 12-64 1300-2700 55 4-6 214 THM-3C 30 86.4-198 24-55 9-52 1000-2200 71 4-6 245 THM-3D 60 THM-4D 60 162-360 45-100 12-56 800-1550 65 5-8 365 THM-4E 120 THM-6E 120 360-828 100-230 10-61 500-1140 72 2-9 510 THM-6R 300 THM-8ST 560 612-1368 170-380 11-61 400-850 71 4-10 686 THM-10ST 560 936-1980 260-550 7-68 300-800 82 6 762 THM-12ST 560 1260-2772 350-770 13-63 300-600 77 3-10 965 THM-14ST 1200 1368-3060 380-850 11-63 250-550 79 4-10 1067 exported wooden crate

Specification : •Size range (discharge) 1” to 18” 25 mm to 450 mm •Capacities to 22,000 gpm to 5,000 m3/hr •Heads to 240 ft to 73 m •Pressures to 300 psi to 2,020 kPa. Size: inlet : 1.5”-18” outlet:1”-16” Weight:77kg-18864kg Dimension: 0.2cube-16cube.

Metslurry high head slurry pumps have been specifically designed to combat the need to run conventional design slurry pumps at excessive speeds to generate high heads often required in many modern slurry pumping applications. Wooden case with plastic inner packing.

NSQ submersible sludge pump is hydraulic machinery, the motor and the pump of which are coaxially submerged in medium to work. The overflowing parts of the pump are made from high alloy wear-resistant material, so the pump has good wear resistance and large flowing passage. It is applicable for conveying media such as sludge, ore slurry, coal slurry, sandstones containing big solid particles. The product is designed and manufactured by domestic and oversea advanced technologies. Besides the main impeller, the bottom of the pump is additionally provided with a set of agitation impeller which can spray the deposited sludge into turbulent flow, and therefore the pump realizes high-concentration conveying under the condition of no auxiliary device. The unique seal device can effectively balance the pressure inside and outside the oil chamber, so as to protect the reliability of the mechanical seal to the maximum extent. The motor adopts various protective measures such as overheat protection, water inle t detecting protection, and can operate safely for a long term in harsh working conditions. The pump is applicable for pumping sand for building, silty sand, silt, tailing slurry, ore, iron sand ore, sediment in sewage treatment works, etc. Structural Property 1.The whole machine is dry submersible pump, and the motor adopts oil chamber seal mode and is provided with mechanical seal inside, so that high pressure water and impurities are effectively prevented from entering inner cavity of the motor. 2.Besides the main impeller, there is the agitation impeller which can agitate the sludge deposited on the water bottom into turbulent flow and pump the sludge out. 3.The trans-flux parts such as the impeller and the agitation impeller are made from high-hardness high chromium cast steel, have wear resistance, corrosion resistance and strong drainage capacity, and allow big solid particles to pass. 4.The motor is submerged in water, is not limited by suction stroke, and has high sludge suction rate and thorough desilting. 5.The integral device is simplified, needs no auxiliary stirrer device or ejector device, and has simple and convenient operation and low total investment of the unit. 6.The agitation impeller directly approaches the depositional surface, and controls the concentration through submerged depth. Under the condition of large medium proportion, an auxiliary device can be arranged to increase the concentration of the medium. Use Conditions 1 The power source is 50Hz/380V three-phase alternating-current supply, and the capacity of the substation transformator is two to three times of the rated capacity of the motor. 2 The temperature of the medium cannot exceed 60íµ, and the medium does not contain inflammable or explosive gases. 3 The maximum weight concentration of the solid particles in the medium: the maximum weight concentration of the ash is 45% and the maximum weight concentration of the slag is 60%. 4 The submerged depth of the unit is not more than 20 meters, and the minimum submerged depth takes submerging of the motor as reference. 5 The unit works in the medium vertically, and the working status is continuous. Weight is 210KG.

Specification: slurry concentration: ín 70%, capacity: 30-1000m3/h , Slurry granularity: :10mm , head to: 60-1000m Pump resistance efficiency: 0.7-0.85 Application area: A) long distance, high-lift transportation for the trailing of black metal, color metal, gold, minerals . B) long distance, high-lift transportation for gray water, bauxite, red mud, cws from power plants, aluminum, coal, chemical industry C) long distance, high-lift transportation for D) sewage sludge treatment plant for the long-distance, high-lift transport E) desilting for rivers and lakes 10ton

Slurry pump is a kind of centrifugal pump, which usually means that under the action of centrifugal force, the liquid is thrown from the center of impeller to the outer edge and obtains energy, leaving the outer edge of impeller at high speed and entering the volute pump shell. In the volute pump case, the liquid slows down due to the gradual expansion of the flow channel, and then transforms part of the kinetic energy into static pressure energy, which flows into the discharge pipe at a higher pressure and is sent to the required place.

Slurry pumps are primarily made use of in dredging, mining, metallurgy, metropolitan, electric power, coal, thermal power flue gas desulfurization, petroleum, chemical, and also structure products sectors to transfer slurry consisting of abrasive solid particles. Such as beneficiation in a mine The transportation of medium slurry, the hydraulic ash removal of thermal nuclear power plant, the coal slurry and also hefty tool transport of coal cleaning plants, as well as the transportation of some corrosive slurry having crystals in the chemical industry. On top of that, in the field of seawater sand selection, the application fields of slurry pumps wholesale have likewise raised. Yet pick sand in the sea as well as dig sand in the river. Slurry pumps are called gravel pumps and also dredging pumps. Although they are called in different ways, they can all be called China slurry pumps in terms of architectural attributes and pump performance characteristics. Slurry pumps are commonly made use of in different sectors.

The current Horizontal Slurry Pump China is commonly utilized in mining, electrical power, metallurgy, environmental protection, petrochemical, new structure products and also various other markets to transport slurry including strong fragments The wholesale slurry pump has a vast efficiency array, good cavitation efficiency and also high effectiveness. Multi-stage tandem technology can be used to fulfill long-distance transportation. There are a range of steels available for overcurrent parts, as well as boost the deepness. Using numerous rates and also several versions allows the slurry pump for sale to run in a better industrial and mining setting. It has a long life span and also high operating effectiveness, and also can meet many kinds of harsh transportation problems.

Long Teng horizontal slurry pump Application: M, SH, HH series pumps contain cantilever and horizontal centrifugal pumps,which apply to transport slurry with strong corrosion proof and high concentration for such industries as metallurgy, mine, coal, power, building etc. This kind of pump can be used in multi-stages. slurry pump for sale body consist of replaceable metal or rubber lining and its impeller is made of wear resistant metal or rubber. HH series lining and impeller are made of wear resistant metal.The shaft seal of M, SH and HH series pump may adopt packing seal or centrifugal seal.Pump outlet can be spaced by 45ã??and installed by rotating eight different angles as per requirement. slurry pump manufacturers SELECTION: Selection As Per Performance Curve @ M, SH series High concentration, High corrosion slurry, Capacity: 40~80% Medium concentration, Medium corrosion slurry, Capacity: 40~100% Low concentration, Low corrosion slurry, Capacity: 40~120% @ HH Series Medium concentration, Medium corrosion slurry, Capacity: 40~80% Low concentration, Low corrosion slurry, Capacity: 40~100% (Maximum efficiency point Capacity is 100% under certain rotation speed.)

Big Capacity Centrifugal Slurry Pump With High Chrome Alloy Product Description Centrifugal slurry pump is a kind of centrifugal pump used for conveying water and solid mixture medium, It is suitable to convey strong abrasive and hard solid medium,such as mining slurry, ash slurry, cement slurry, gravel etc. Centrifugal Slurry Pump Centrifugal Slurry Pump Sand Suction Pump Features Centrifugal Slurry Pump Parameters: 1. Material: High chrome alloy 2. Discharge distance: 100-2000m 3. Flow: 45-2300m3/h 4. Head: 9-135m 5. Max particle size: 50mm 6. Motor power:15-1200KW 7. Working temperature: â?¤80�ºC Centrifugal Slurry Pump Advantages: 1. High performance wear resistant,corrosive resistant. 2. Double pump casing structure. 3. Easy to use and maintain. 4. Do material testing before pouring and after pouring. 5. Use best bearing in China or SKF,TIMKEN brand bearings. 6. Modularization of main parts. No broken, easy to disassemble and repair. Specification: Type Flow(m3/h) Head(m) Speed(r/min) Eff(%) Power(kw) DS400-100 2339 55 590 76.9 560 DS350-100 1785 59.7 590 80.4 450 DS350-70 2118 66.7 980 80 630 DS300-75 1100 92 980 76 450 DS300-75 819 51 730 76 185 DS250-75 750 95.7 980 72 355 DS250-63 592 35.5 730 76 110 DS200-65 500 73 980 69 185 DS200-55 321 28.2 730 69 45 Please send message to get more information if you have other inquiries. Applications This centrifugal slurry pump is suitable for mud or sludge conveying, river dredging, sewage treatment, sand extraction, land reclamation, coastal embankment, dock construction, and also can be used in power plant, metallurgical transportation, tailings

The AZ series centrifugal horizontal slurry Pump is Chinese design slurry pumps. It is advanced designed in oil lubricated frame could be more steady work in high pressure or the pumps in series. The impeller design is advanced and could be adjusted according to the requirement of the work site instead of using different type of pumps which is Min the pump and parts required and much easy to use and main. The AZ series centrifugal horizontal slurry Pump is widely used in power plant, metallurgy, mining, coal, building material and chemical industries to deliver abrasive fluid which is the best choice for updating old design slurry pumps! -!

Place of Origin:China Usage:Water Power:Electric Standard or Nonstandard:Standard Fuel:Electric Flow:24-4500m3/h Head:11-60mOutlet diameter range:50-450mm Packaging Details:Seaworthy wooden cases Delivery Detail:within 2 month

Machinery, wire & mesh machine, agricultural & garden tools, pipe fittings, thread roller, thread rolling machine and thread rolling dies..