Drill subs are an important integral part of everyday drilling. Not having the right thread adapter can make your life miserable. We have a large inventory of common and not so common sizes. Custom sizes are always available. Rotary subs have two primary applications. They can be used to cross over from one connection size to another, or as the disposable component used to extend the connection life of a more expensive drill stem member. Installing a float sub (with check valve) is always a good idea when drilling in wet situations.
Drill Collars are integral heavy-wall joints that are manufactured from a solid bar of modified alloy steel. The solid bars are quenched and tempered to obtain the required mechanical properties, then trepanned, drifted and threaded. All drill collars are heat-treated with hardness within 285 to 341 BHN, which are guaranteed one inch below the surface of the pipe. Lake Petroleum could supply slick type drill collar, spiral drill collar and Non-magnetic drill collar (NMDC).
Downhole motor is a kind of downhole power frilling tools by mud. The mud output by the mud pump, will enter the motor through the bypass valve, and a certain pressure difference will be formed at the inlet and outlet of motor, to push the rotor of motor to rotate, and to transfer the torque and the RPM to the drill bit via the universal shaft and the driving shaft. Drilling downhole motors offer a wide range of configurations to meet different needs. These motors have the power, torque, and speed to drill with the PDC bits for specific downhole conditions or well designs. Using the latest available technology and materials, the motors can be used in an extensive range of drilling applications, such as: Vertical, directional, and horizontal wells High temperature Synthetic-, oil-, and water-based mud systems Performance drilling Extended-reach wells
Lake Petroleum could supply a huge quantity of new drill pipe for sale, available in all standard sizes and weights, to quickly meet the drilling equipment needs of companies in the oil, gas and Geothermal industry.
Description: Cementing Plugs are used to remove the mud during cementing operations. There are two types of Cementing Plugs used in the cementing process: Bottom Cementing Plug and Top Cementing Plug. The Top Cementing Plug has a solid body that provides positive indication of contact with the landing collar and bottom plug through an increase in pump pressure. The Bottom Cementing Plug is launched ahead of the cement slurry to minimize contamination by fluids inside the casing prior to cementing. Available in standard and non-rotating types.
Description: Stop Collar is also called limit ring, stop ring, brake ring and so on. Used to limit the sliding of the centralizer or cement umbrella on the inner casing. There are slip-on stop collar, hinged spiral nail stop collar, hinged bolted stop collar and hinged set screw stop collar and so on.
Description: Drift Diameter Gauge is a special tool for testing the diameter of downhole tubular. It is mainly used to test whether the diameter of the inner diameter of the casing, tubing, drill pipe, etc. meets the standard, and is a commonly used testing tool for underground operations.
Description: Casing Centralizer is a device used to place the casing at the center of the hole so as to improve the efficiency of the cementing. It is an important device because if the Casing Centralizer touches the formation at any part of the hole, then cement slurry does not pass through the area of the contact resulting in a poor cementing job.
Description: Basic floating Equipment includes the Float Collar and Float Shoe: The Float Shoe contains a backpressure valve that prevents fluids from entering the casing while the pipe is lowered into the hole and prevents cement from flowing back into the casing after placement, while enabling circulation down through the casing. Float Collars are placed one to three joints above the Guide Shoe or Float Shoe. They provide a seat for the cement plugs, the bottom plug pumped ahead of the cement and the top plug behind the full volume of slurry. Once seated, the top plug shuts off fluid flow and prevents over-displacement of the cement. The space between the Float Shoe and the Float Collar provides a containment area to entrap the likely-contaminated fluids from the wiping action of the top cementing plug, securing the contaminated fluid away from the shoe where a strong cement bond is of primary importance. Float Collars include a backpressure valve and serve basically the same function as the Float Shoe.
Description: A Blind Flange is a solid disk used to block off a pipeline or to create a stop. Like a regular flange, it also has mounting holes around the perimeter and the gasket sealing rings machined into the mating surface. The difference is that a blind flange has no opening to allow fluid to pass through. 1522095217@qq.com
Description: Casing Head Assembly is the adapter between the first casing string and either the BOP stack or the wellhead. This adapter may be threaded or welded onto the casing, and may have a flanged or clamped connection to match the BOP stack or wellhead. 1522095217@qq.com
Description: A Companion Flange, sometimes referred to as a hub, is a flange that corresponds to another flange. It has bolt holes that align with another flange is a trait of this type of flange. Usually a companion flange features a Raised Face (RF) or Ring Joint (RTJ), with a threaded outlet. Also called a Threaded Flange by some people.
Description: Double Studded Adapter Flange (DSAF) or Double Studded Adapter (DSA) is a flange with a through bore and a ring groove on each side, drilled and tapped bolt hole sets on both sides and tapped end studs complete with nuts fitted on both sides. Unlike a spacer, the two sides are usually different in size and/or pressure rating. Double studded adapter flanges are commonly utilized to connect and adapt flanges with different nominal sizes, pressure ratings, and configurations. We also produce and supply other types API 6A flanges, such as threaded flanges, spacer spool flanges, blind flanges, companion flanges, target flanges, test flanges, and adapter spools for all cli
Description: Tubing head is a spool with flange top, flanged bottom and two side outlets. It also can be called tubing spool. Top flange is equipped with lock screws to fix tubing hanger. Tubing head is installed on top of casing head, which consists of body housing and tubing hanger. It can hang tubing string and seal the annular space between tubing and production casing. Our company can manufacturer tubing head with standard structure, which includes tubing hanger installed on the cone of body housing. Tubing hanger can be tapped with BPV thread as per request.
Description: API 6A Weld Neck Flanges are pipe flanges attach by welding the pipes to the neck of the flanges. This transfers stress from the flange to the pipe instead. It also reduces the stress concentration from the base of the hub. Welding neck flanges remove stress concentration and allow full working pressure and they are often used for high pressure applications. The inside diameter of the flange is designed to match the pipe's inside diameter. Weld neck pipe flanges are typically provided with a raised face, flat face, or RTJ facing.
Description: Spacer spools in all sizes and pressure ratings that are compliant to API 6A and API 16A. Spacer spools are suitable for wellhead extension, BOP installation, choke & kill manifold spools and production manifold. End connections are flanged, studded, threaded, clamp hubs or other end connectors (OEC). Some customers uses names like "riser spool" or "surface riser spools". Customer should specify the length accordingly to stack height. Each spool is pressure, drift and dimensionally tested before shipment.
Mud Cleaner is the second stage and the third stage solids control equipment which is a combination of Desander, Desilter and underflow shaker shaker. Comparing with traditional separate Desander and Desilter, the mud cleaner has a higher cleaning function. The Underflow Screen equals another shaler shaker which receives the waste out from the cyclone nozzle for additional processing. So that mud cleaner could recover more valuable drilling mud. Mud cleaner is the ideal dev
Sand pump is widely used in solids control system. Internal the mud system, It can be located before the de-sander, de-silter and mud cleaner to transfer the drilling mud to the cyclone unit, equipped to the jut mud mixer unit as the mud mixing pump. For external of the mud system, the Sand pump can be used as the trip pump for mud supplement under well and the supercharging pump to transfer the drilling fluids to high pressure rig mud pump. The solids contained in drilling fluids request the Sand pump wet contacting parts with excellent wear resistance and high efficiency on flow rate. Based on the mat
Downhole motor is a kind of downhole power frilling tools by mud. The mud output by the mud pump, will enter the motor through the bypass valve, and a certain pressure difference will be formed at the inlet and outlet of motor, to push the rotor of motor to rotate, and to transfer the torque and the RPM to the drill bit via the universal shaft and the driving shaft. Drilling downhole motors offer a wide range of configurations to meet different needs. These motors have the power, torque, and speed to drill with the PDC bits for specific downhole conditions or well designs. Using the latest available technology and materials, the motors can be used in an extensive range of drilling applications, such as: Vertical, directional, and horizontal wells High temperature
Drill subs are an important integral part of everyday drilling. Not having the right thread adapter can make your life miserable. We have a large inventory of common and not so common sizes. Custom sizes are always available. Rotary subs have two primary applications. They can be used to cross over from one connection size to another, or as the disposable component used to extend the connection life of a more expensive drill stem member. Installing a float sub (with check valve) is always a good idea when drilling in wet situations.