Fusible Interlining Suppliers and Manufacturers

We are prominent processors and exporters of a wide range of dextrin including Tapioca White Dextrin that protects the fiber by forming a thin coating and also provides stiffness to some of the varieties of interlining fabrics. It is highly appreciated as an efficient thickening agent for textile printing purposes. It is made from eco-friendly raw materials and used as a carrier in color as well as dyestuff industries.

We are prominent processors and exporters of a wide range of dextrin including Tapioca White Dextrin which protects the fiber by forming a thin coating and also provides stiffness to some of the varieties of interlining fabrics. It is highly appreciated as an efficient thickening agent for textile printing purposes. It is made from eco-friendly raw materials and used as a carrier in color as well as dyestuff industries.

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

Introduction: - Feldspar is primarily used in industrial applications for its alumina and alkali content. Feldspar is a naturally occurring anhydrous, inorganic, igneous rock. The fusibility of the mineral makes it useful raw material for many applications and the purity is the indication of better fusibility in the application. There are two types of it depending On Na2O and K2O SODA FELDSPAR POTASH FELDSPAR Applications: - CERAMICS ENAMEL FRITZ & GLAZED INSULATORS GLASS MILD ABRASIVES PICTURE TUBES SANITARYWARE TABLEWARE VITRIFIED TILES WELDING ELECTRODE Available Mesh Size: - 100 - 500 MESH Custom sizes and Material of required specifications can be made in case of Bulk and Regular orders. TYPICAL CHEMICAL COMPOSITION OF POTASH FELDSPAR Index ompound Unit Result 1. Silica - (SiO2) % 66 - 68 2. Alumina - (AI2O3) % 17 - 18 3. Iron - (Fe2O3) % 0.03 - 0.06 4. Titanium - (TiO2) % 0.03 - 0.06 5. Calcium - (Cao) % 00.00 6. Magnesium - (MgO) % 00.00 7. Soda - (Na2O) % 2 - 3 8. Potash - (K2O) % 10 - 12 9. Loss on Ignition - (LOI) % 0.10 - 0.20 TYPICAL CHEMICAL COMPOSITION OF SODA FELDSPAR Index Compound Unit Result 1. Silica - (SiO2) % 68 - 72 2. Alumina - (AI2O3) % 17 - 18 3. Iron - (Fe2O3) % 0.10 - 0.15 4. Titanium - (TiO2) % 0.03 - 0.06 5. Calcium - (Cao) % 0.05 - 0.20 6. Magnesium - (MgO) % 0.10 - 0.15 7.Soda - (Na2O) % 9 - 10 8. Potash - (K2O) % 0.50 - 0.20 9. Loss on Ignition - (LOI) % 0.10 - 0.20

This type Chips that is designed to resist burning and melting at low temperatures. Low Melting Point Polyester Chip for Hot Melt Yarn Masterbatch Extrusion Grade Polymer for Hot-melt Adhesive Glue Coating Description: Generally speaking, the low melting point polyester chip refers to one specialty polymer with a melting point between 90 and 220. The melting point of polyester is the temperature at which a solid crystalline substance changes from a solid state to a liquid. So it reflects the purity of polyester. Generally speaking, pure polyester is a partially crystalline polymer with a melting point of 265. But during actual production, some impurities exist in the polyester due to various side reactions. At the same time, the defects of polymer crystals and the difference in crystallinity will also affect the melting point. The common type of low melt polymer is 110. But we can also offer a melting point of 90, 120, 160, and 180. Application: Low-melt polyester chips can produce low-melting point fiber, low-melting point synthetic fiber, and thermal-melting mucilage. Its primary usage is acting as bonding fiber in nonwoven fabrics. The end usage lies in clothing, articles for bed, shoe uppers, sleeping bags, sofas, and hygiene products. LM PET Chip is also the main raw material of masterbatch carriers. That is, low-melt PET chips, conventional chips, and dyes are mixed to produce the polyester color masterbatch according to a certain proportion. The production of this product is the introduction of polyester macromolecules into the modified copolymer unit. And its melting point is in the range of 100-120. Commonly used modifiers are phthalic acid, adipic acid, and trimethylolpropane. Recently, LM Polymer is also extruded into the back coating of nonwoven, automotive interiors, foam, injection molding, PET sheets, and hot-melt adhesive/glue. Low Melt Yarn is also called hot melt yarn or fusible yarn. There are sheath-core low-melt bicomponent yarn and full low-melt polyester yarn.

Specifications Products : Potash Feldspar Use : Industrial Use Color : Pink to White Form : Powder Packing Type : Small Plastic Bags / Jumbo Bags Packaging size : 50kgs / 1000-1200 kgs Feldspar are chemically alumino-silicates. There are several types of feldspar available in the state of Rajasthan (India): Most deposits offer sodium feldspar, potassium feldspar and mixed feldspar. The fusibility of the mineral make it useful raw material for many application and the purity is the indication of better fusibility in the application. The geological context specific to each deposit gives the feldspar a variety of physical and chemical properties, thus providing products for a full-range of ceramic and glass making applications. At mines the deposits are blasted to break up the rock and make it accessible to the diggers and loaders. The material after breaking up are manually sorted to prepare feed stocks and than each lot is tested with a view to providing the process plant with a constant homogeneous supply that is appropriate for the application purposes. The selected material is than transported to the users. The remaining product (R/O) is directly sold in the form of sand to glass manufacturers or ground for ceramic markets. The processing techniques at PEEKAY MINERALS ensures consistent quality freedom from impurities at pocket friendly costs. Application: As fluxing agent in ceramics- tiles, sanitary tableware, and glazes As strength enhancing in glass and glass wool As transparency enhancer in hollow glass, flat glass As fillers in paints, plasters, insulation Features: Free from impurities Good color High strength High Alumina Required sizing