This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
PRODUCT DATA SHEET ACID RESISTANT BRICK Material : RED SHALE Type Acid Resistant Brick Size (mm) 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions Heavy thermal shock Typical Physical Properties of GANESHAS Acid and Chemical Resistant Brick Characteristic RED SHALE ACID RESISTANT BRICK Test Standard Bulk Density, gm/cc - 2.3 to 2.35 ASTM C-20 -Water Absorption, % - 0.1 to 1.5 IS 4860-1968 Apparent Porosity, % -0.5 to 1.75 S 4860 Acid Solubility (H2SO4), Loss in Mass,% -0.1 to 1.8 ASTM C-279 Modulus of Rupture, PSI -2133 to 3555 ASTM C-67 Compressive Strength, Kg/cm2 - 700-900 IS 4860-1968 Abrasion Resistant , Volume in mm3 -69 to 85 EN 102 Surface Hardness, MOHS Scale - 7
PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103
Desiccated Coconut is a kind of healthy food, commonly used in daily life. In addition to the function of supplying nutrients for healthy, Desiccated Coconut also has a function in beauty. 99 Gold Data provides customers with a wide range of products include: + High fat - Fine grade + High fat - Medium grade + Low fat - Fine grade + Low fat- Medium grade Note: High fat 62% min, Low fat 32-40 %.
Natural fibers present important advantages such as low density, appropriate stiffness and mechanical properties and high disposability and renewability. Moreover, they are recyclable and biodegradable. There has been lot of research on use of natural fibers in reinforcements.
Introducing our exquisite range of wooden toys, designed to captivate and educate young minds. Crafted from high-quality, eco-friendly wood, each toy is not only safe and durable but also beautifully finished. Our collection includes a variety of engaging options, from classic building blocks to intricate puzzles, all aimed at fostering creativity, motor skills, and cognitive development.
Type: Chopping Blocks Commercial Buyer: Restaurants, Food & Beverage Stores, Food & Beverage Manufacture, Department Stores Season: Everyday Room Space: Kitchen, Dining Room Design Style: Modern Material: Bamboo/Wooden Feature: Sustainable Place of Origin: Vietnam Brand Name: 99 GOLD DATA Model Number: Selena +84 587 176 063 Product name: Cutting Board Usage: Kitchenware Color: Customized Color Keyword: Custom Chopping Board Function: Cutting Food Board MOQ: 1000pcs OEM & ODM: Accepptable High Quality: 100% Eco-friendly Description: Chopping Cutting Board Blocks PAYMENT: TT 30% Deposit Supply Ability 20000 Piece/Pieces per Month Packaging Details Poly bag;Shrink package;White box;Color box;PVC box;PDQ display box Port All port in Vietnam
We are supplier and exporter of Petroleum Coke. Petroleum Coke are made from a mixing material of serval kinds of coal,under a high temperature(1300) process.They are widely used for steelmaking,ferroalloys manufacture or non-ferrous metals smelting,iron castings manufacture or other related metallurgical and foundry industry,because of its special physical and chemical characteristics:high strength and fixed carbon content,low sulfur and low volatile matter content.
A Modified Starch for Thickening, Stabilizing in various Shear applications. Monopoly product in India Gives Medium Smooth Thickness and Texture Maintains the stability at low temperature Excellent Resistance to High Temperature Excellant Thaw Freeze Stability E1422 Modiified Starch Suitable for All kinds of Sauces, KetchUp, Salad Dressings, Instant Foods
Dried Lotus Seed Lotus seeds are low in cholesterol, saturated fat and sodium. Therefore, they are good for the heart too. Lotus seeds are also extremely good sources of magnesium, potassium, manganese, protein, and phosphorus. Their extremely high nutrient content makes them an extremely healthy snacking option.
We suppy high quality the dried dragon fruit- This is a beautiful and exotic superfood. These organic dried dragon fruit slices are rich in nutrients and low in calories. They have a mild sweet taste with no sugar added. Snack on this unique organic treat for a good source of antioxidants, fiber, omega-3s and minerals. ***Here are 7 health benefits of dragon fruit, all based on evidence. - High in Nutrients. Share on Pinterest. ... - May Help Fight Chronic Disease. ... - Loaded With Fiber. ... - Promotes a Healthy Gut. ... - Strengthens Your Immune System. ... - May Boost Low Iron Levels. ... - Good Source of Magnesium.
Natural Rubber SVR3L have good resilience, abrasion and surface friction properties and excellent compression set. It has low hysteresis and rolling resistance with high fatigue resistance and remains flexible at low temperatures. Natural rubber SVR3L has poor resistance to oil, sunlight and ozone and limited thermal capability. Natural rubber SVR3L is superior tear strength and excellent resistance to heat buildup continues to make it a favored ingredient for high-performance tires for race cars, trucks, buses and aircraft. Other applications include tank lining, engine mounts, seals, vibration dampening and diaphragms.
Natural Rubber SVR3L have good resilience, abrasion and surface friction properties and excellent compression set. It has low hysteresis and rolling resistance with high fatigue resistance and remains flexible at low temperatures. Natural rubber SVR3L has poor resistance to oil, sunlight and ozone and limited thermal capability. Natural rubber SVR3L is superior tear strength and excellent resistance to heat buildup continues to make it a favored ingredient for high-performance tires for race cars, trucks, buses and aircraft. Other applications include tank lining, engine mounts, seals, vibration dampening and diaphragms.
Good Feeling 2D KF94 Quarantine Mask is a quality product approved by the Korean Ministry of Food and Drug Safety.  Respiratory protection from harmful particulate matter such as yellow dust, fine dust, and infectious sources  1. V-Fit thin face design With thin face visual effect. The inside does not touch the lips for a comfortable fit. 2. High-specification MB filter The Korean-made high-standard MB filter can block more than 94% of particulate harmful substances such as sandstorms, fine dust (PM2.5), and infection sources. 3. High elastic ear straps Use high elastic ear straps for comfortable wearing Mask size (unopened): 13 (w) x 14.5 (h) cm
FROZEN SUGARCANE ROC 16 Origin: Vietnam Size: 40-50 cm Quality fresh sugarcane Peel, Wash Drain , Cut into pieces , Packing , Freezing (-18 degrees C) *Selected fresh sugarcane: Sugarcane is grown and cared to ensure no pesticide residue. In addition, sugarcane is selected from 16 sugarcane with high sweetness. *Peel: Sugarcane is shaved off the silk outside before washing Washing the cane The cane is washed in a tub with a spray nozzle under *Cutting into pieces: Sugarcane is cut into requested format from customers. The length is from 25-50cm *Packing Packing of PA or PE bags ensures export qualityFreezing sugarcane Block sugarcane is frozen at -18 degrees C
A unique copolymer warp yarn sizing agent for Cotton, Rayon, Modal Polyester and Blends of Polyester/Cotton/Viscose Spun yarns. Heavy fabric constructions are easier to weave at low size add-on using SizeMagik-LP4. Low add-on also permits greater protection on high speed looms expensive reeds and sensitive mechanical parts life. Better film properties of the product provide the lower warp breaks and it improve the finished products quality. Reduced dropping level in sizing and weaving it provide more comfortable working conditions and reduce maintenance cost.
ER3MG302 3h 1 Miniaturization 2 Low power consumption 3 High cost performance 4 Total temperature compensationType Honey mango Taste soft sour and sweet Shelf life at least 12 months Origin Ho Chi Minh City Vietnam Process Air Dry with 15 sugar No other preservatives additives non SO2 Quantity capacity 50 tonsmonth Min order quantity no Packaging in 10 kgs carton 1x20ft 135mts buyers brand available
Dried fish collagen protein subjected to the production extraction is high in content of extracted protein and amino acid and relatively low in content of fat, can meet the demand of human body to nutrient substances each day, is easily absorbed and utilized by the human body, and is helpful for improving the immunity of the organism of a human body, improving the memory, keeping the body healthy and energizing the body after long-term use.
