DESCRIPTION ITSEAL is truly developed for sealing window frames with highly durable and flexible properties to withstand severe weathering and extreme temperatures. It seals small gap that normal sealant cannot reach and penetrate. It provides a truly watertight seal deep into minute joint and gap. FEATURES * ITSEAL is the only waterproof sealer that is completely watertight. * It is highly water repellent that no water can get through it during storm. * It adheres well on aluminum and glass * Once dried, ITSEAL is flexible and accommodate joint movement due to vibration. * Mill finish aluminum, oil or wet surfaces can also be well-sealed. VOC CONTENT Type of Regulated Adhesive under the Air Pollution Control (Volatile Organic Compounds) Regulation of Hong Kong: Architectural Sealant VOC Content (Ready to use): 248g/Ltr. SURFACE PREPARATION For maximum adhesion, the adhesive surface must be free of dust, release agent, oil and grease. Wipe surface with solvent is recommended. Solvent are obtainable from ITLS-SB. This information in this catalogue is provided to the best of our knowledge from results gathered both internal and external credited laboratories. However, we have no control over site applications, site conditions and workmanship of the applicator. We therefore will not accept any liability, either directly or indirectly arising from the misuse of these products or when the product is used not in accordance with any advice, specification, and recommendation of information given by us, The user is responsible for checking the suitability of these products for its intended use. APPLICATION ITSEAL can be used with hand operated or air operated grease pump. Other simple extruding device can also be used but it has to be solvent resistance. LIMITATION * Not suitable large gap wider than 5 mm wide and deep. For deeper joint fill to half of it, let it dry overnight and fill it up the next day. * Not suitable for use as expansion joint. COLOUR AND PACKING 26 kg / pail Grey/Black/Bronze/White SAFETY INFORMATION * ITSEAL is flammable. Please keep away from sources of ignition during application. * Avoid breathing in solvent by wearing solvent vapor respiratory mask in badly ventilated area or confined space. * Avoid contact with skin and eyes. If swallowed please contact doctor immediately. * ITSEAL meets the requirement of RoHS regulation of European Union and it does not contain eight heavy metals which were restricted by ASTM F963 or EN71 part3. * Please read the Material Safety Data Sheet in regards to flammability and health and hazard. SHIPPING/STORAGE INFORMATION ITSEAL must be stored in a cool place under 25°C and away from direct sunlight. The shelve life is 12 months if stored in accordance to the recommendation. Dangerous Goods Information: Cement Adhesive, Class 3, UN1133 PG III.
Hdpe bottle scrap, hdpe drum scrap, ldpe film scrap, pet bottle scrap, drained battery scrap, fridge compressor scrap, aluminium scraps, brass honey scrap, copper scrap.
Expanded Metal Walkway Grating&Floor&Ramps Expanded Metal Wire Mesh Rigidity Expanded Metal Mesh Expanded metal grating products are used for a variety of uses such as walkways, catwalks, screens, fencing, window guards, open trash containers, vent covers and many more applications. Peterson Company carries expanded metal in a variety of materials such as aluminum expanded metal, stainless expanded metal, galvanized expanded metal, carbon steel expanded metal, copper expanded metal, brass expanded metal and titanium expanded metal. Product Details A strong and aesthetic solution for walkways and gantries. The Expanded Metal DONGJIEs heavy duty walkway range is an effective well established product, proven throughout industries where safety underfoot is critical. When lives can depend upon strength and grip, at heights and in hazardous conditions, the Expanded Metal Companys range can be relied upon to satisfy safety requirements. The Expanded Metal walkway range is excellent for slopes and heights due to its anti-slip properties. Mesh allows the free ow of water to give natural drainage. Snow,ice and mud break off underfoot to maintain secure footing. The solid appearance of the walkway range gives an excellent aesthetic appeal for design. Features and Benefits Quality Guaranteed ISO 9001: 2008 Environmental Mana gement ?�Technical support available Wide choice of standard products ?�Available in Stainless Steel, Aluminium& Mild Steel Economical solution for all types of walkway and gantry applications Tested and measured load bearing capacities New Gripwalk for extra anti slip protection Supagrip gives _x001D_firm hold for both wheelchairs and footwear Option to weld or clip the sheets in situ Plasma cutting service for efficient and accurate shaping Superb strength to weight ratio Low maintenance Material Specifications You can choose from a wide range of standard items from gripwalk for extra anti-slip protection or walkway in a range of materials with measured load bearing capacities. Products in the DONGJIEs range give a non-slip, economical solution for all types of walkways, stairtreads and gantries. Aluminium Walkway Ref No. LWD SWD Swdt Stk Kg/m� % Open Area Overall Thickness Standard Manufactured Size 2496 60.96 25.40 5.82 4.70 6.08 52 12.70 2440 x 1830 4895A 121.92 38.10 11.90 6.00 10.16 43 20.60 Mild Steel Walkway Ref No. LWD SWD Swdt Stk Kg/m� % Open Area Overall Thickness Standard Manufactured Size 2496 60.96 25.40 6.10 4.5 17.29 51 12.70 2440 x 1220 4896 121.92 33.87 6.35 4.5 13.23 65 13.50 4897 121.92 33.87 7.90 4.5 16.45 58 15.10 4898 121.92 33.87 9.53 4.5 19.83 50 17.50 4899 121.92 33.85 9.53 6.00 24.98 50 19.80 4894 121.92 38.10 13.06 6.00 32.22 38 22.20 Material Illustrations---A
KZB ISO 7241 B Series Hydraulic Quick Couplings (steel) Features Connexionby pullingback the sleeve Disconnexion by pulling back the female sleeve Shut off by poppet valve Connexion under pressure not allowed Disconnexion under pressure not allowed Interchangebility according to ISO 7241-1 part B Technical Specifications High grade carbonsteel with heat trearted wear parts Polyurethane and NBR Backup ring in PTFE -25�°C to +100�°C According to ISO 7241-2 Product Categories 1.ISO 7241A KZE ISO 7241 A SERIES HYDRAULIC QUICK COUPLINGS(STEEL) KZEB ISO 7241A SERIES HYDRAULIC QUICK COUPLINGS(STEEL BALL) KZESS ISO 7241A SERIES HYDRAULIC QUICK COUPLIGNS(STAINLESS STEEL) 2.ISO 7241 B KZB ISO 7241 B SERIES HYDRAULIC QUICK COUPLINGS (STEEL) KZD ISO 7241 B SERIES HYDRAUIC QUICK COUPLINGS(BRASS) KZBSS ISO 7241 B SERIES HYDRAULIC QUICK COUPLINGS(STANILESS STEEL) 3.4000SERIES ISO 5675 KPC DOUBLE SHUT-OFF COUPLINGS WITH HARDEND STEEL POPPETS(STEEL)/PIONEER4000SERIES INTERCHANGE 4.PUSH AND PULL TYPE KZA PUSH AND PULL TYPE HYDRAULIC QUICK COUPLINGS(STEEL) KZAF PUSH AND PULL TYPE HYDRAULIC QUICK COUPLINGS(STEEL) KZAV PUSH AND PULL TYPE HYDRAULIC QUICK COUPLINGS(STEEL) 5.ISO 16028 QKPT FLAT FACE HYDRAULIC QUICK COUPLINGS(CARBON STEEL)/INTERNATIONAL INTERCHANGE ISO 16028 6.QKTF THREAD TO CONNECT NDER PRESSURE COUPLINGS(BRASS)
Qianli iClamp screen clip universal LCD clamp fixture for mobile phone iPad screen glass fastening repair. 4pcs Universal QianLi ToolPlus iClamp Metal Clip Fixture has been discontined, new version is QianLi iClamp 2.0 plastic clamp with rubber screen clip fixture. Product Features: 100% brand new and high quality Versatile screen fastening clamp clip Clamp mouth size can be adjusted by rotating the knob to fit for most phone and tablet pc Rubber padding inside help no chance to scratch your phone screen Used to clamp your repaired device. Help the replaced new screen in its right place, not bulge or sink. Make the screen to joint with the frame perfectly. Quality metal made, more durable and tougher than those in plastic. Product Specification : Product material: plastic Product size: 38x29x18(mm) Adjustable range: 5-11mm Package includes : 1pc x Qianli iClamp 2.0 Set (4pcs inside)
SLIDING DOOR Airtight Doors An airtight door is a door that is designed to prevent the passage of air through its edges, joints, or other openings. Airtight doors are commonly used in buildings to improve energy efficiency, reduce drafts, and prevent the infiltration of outdoor pollutants. They can also be used in laboratory or industrial settings to prevent the spread of hazardous materials or to maintain a controlled environment. Airtight doors may be made from a variety of materials, including wood, steel, or aluminum, and may be fitted with weatherstripping, gaskets, or other sealing devices to improve their airtightness. Features of Airtight Doors Airtight doors typically have several features that help to make them effective at preventing the passage of air: Weatherstripping: This is a seal that is applied around the edges of the door to prevent air from entering or exiting through the gaps between the door and the door frame. Gasketing: Gaskets are seals that are installed between the door and the frame to prevent air from passing through the joint. Tight-fitting door: Airtight doors are designed to fit tightly within their frames to prevent air from passing through gaps. Threshold: Airtight doors typically have a threshold that is designed to seal against the floor to prevent air from entering or exiting under the door. Self-closing mechanism: Airtight doors may have a self-closing mechanism that helps to ensure that the door is closed tightly and securely, further reducing the passage of air. Pressure relief vents: These vents allows the pressure inside the room to be equalized with the outside, avoiding any damage to the door or frame. Material: Airtight doors are commonly made from materials that are durable, long-lasting and can withstand the rigors of daily use, such as metal or metal-clad wood.
Airtight Doors An airtight door is a door that is designed to prevent the passage of air through its edges, joints, or other openings. Airtight doors are commonly used in buildings to improve energy efficiency, reduce drafts, and prevent the infiltration of outdoor pollutants. They can also be used in laboratory or industrial settings to prevent the spread of hazardous materials or to maintain a controlled environment. Airtight doors may be made from a variety of materials, including wood, steel, or aluminum, and may be fitted with weatherstripping, gaskets, or other sealing devices to improve their airtightness. Features of Airtight Doors Airtight doors typically have several features that help to make them effective at preventing the passage of air: Weatherstripping: This is a seal that is applied around the edges of the door to prevent air from entering or exiting through the gaps between the door and the door frame. Gasketing: Gaskets are seals that are installed between the door and the frame to prevent air from passing through the joint. Tight-fitting door: Airtight doors are designed to fit tightly within their frames to prevent air from passing through gaps. Threshold: Airtight doors typically have a threshold that is designed to seal against the floor to prevent air from entering or exiting under the door. Self-closing mechanism: Airtight doors may have a self-closing mechanism that helps to ensure that the door is closed tightly and securely, further reducing the passage of air. Pressure relief vents: These vents allows the pressure inside the room to be equalized with the outside, avoiding any damage to the door or frame. Material: Airtight doors are commonly made from materials that are durable, long-lasting and can withstand the rigors of daily use, such as metal or metal-clad wood.
DESCRIPTION ITLS PMS 60 is a single component elastomeric sealant without isocyanates. It cures rapidly under the effect of atmospheric humidity to form a flexible and resistant joint with very good adhesion on most materials. APPLICATION ITLS PMS 60 is suitable for industrial and refrigerated trailers, truck bodies, shipbuilding, air conditioning and ventilation units, sandwich panels and other industrial applications. ITLS PMS 60 can also be used for bonding and caulking different materials used in the building industry : concrete, wood, aluminum, most lacquered metals, polyester, glass, stone, ceramic, and so on. However, for difficult materials especially lacquered or non-ferrous metals, it is necessary to make tests beforehand. INSTRUCTIONS FOR USE SUBSTRATE PREPARATION: The substrates must be clean, even, dry, free of dust, oil, grease and any contaminants that could harm bonding. All traces of poorly adherent paints or coatings should be systematically removed beforehand. They may be cleaned with PMS primer, methylethylketone (MEK) or acetone. Check the compatibility of the solvent used with the substrates. It may be necessary to rub down the substrate beforehand. After rubbing down, the surface should be recleaned. Allow the substrate to dry after degreasing. When using solvents, extinguish all sources of ignition and carefully follow the safety and handling instructions given by the manufacturer. CAULKING: ITLS PMS 60 can be applied by a manual or pneumatic gun. After application, use a putty knife to smooth the joint with soapy water. Do not apply at a temperature under 5 C. In cold weather, store the cartridges at about 20 �°C before use. This product should be used within 24 hours of opening the cartridge protection; otherwise, the sealant could harden inside. Avoid any contact with non-cured polyurethanes during curing. CLEANING: Tools can be cleaned with PMS primer, MEK or acetone before the sealant has completely cured. After curing, abrasion is necessary. STORAGE AND SHELF LIFE 12 months in the original, hermetically sealed packagings between 5 and 25 C PACKAGING 290 mL cartridges and 600 ml sausages SAFETY Not classified as hazardous. Read the material safety data sheet before use.
Name : Women Imitation Jewellery Set Base Metal : Brass Plating : Oxidised Silver Stone Type : Artificial Stones Sizing : Adjustable Type : Necklace and Earrings Net Quantity (N) : 1 your style with this comfortable necklace set with earring . Featuring a contemporary refined design, this necklace is perfect to give your quintessential dressing an upgrade. BEAUTY - A Traditional stylish fancy party wear Designer Indian necklace set with earring Earrings for women are perfect for this wedding and festive season.this designer set will add a tinge of charm to your attire. .Care Instruction : Avoid Heat & Chemicals Like Perfume, Deo, Alcohol, Etc., Clean With Dry Cotton Cloth, Pack In An Air Tight Container/ pouch After Use. It is advisable to wear the jewelry after makeup.
Multi-size Hollow Base Cleats Marine Hardware 316 Stainless Steel Mirror Polished for Boat which is beautiful and rich shore Our company possesses the advantaged position on the verge of And we have convenient meanly engaged in the metal products. Our business is a system includes the designing, production, machining and selling. Our products are: rigging, marine hardware, camlock coupling, auto accessories ,as well as the machine parts .According to the standards of API ANSI BS DIN JIS, the products are made to pretty , rational construction, superior performance. The material of our products is kinds of stainless steel ,such as 304 316 316L ;aluminum; brass; pp; nylon and carbon steel. The products are used in many area covering the marine transport, petrochemical industry, Pharmaceutical papermaking, food industry electricity industry and so on.
mesh/brass wire winding machine Shijiazhuang Satle Machinery Manufacture Co.,Ltd. established in the year of 2001, is located in Shijiazhuang City, HeBei Province,China. The company, possessing a professional technical and production team, is mainly specialized in developing and manufacturing the whole set of welding wire production line and whole set metal wire drawing machine, including straight line wire drawing machine, water tank wire drawing machine, pulley wire drawing machine, horizontal drawing machine,trunk type take up machine,spooler take up machine, payoff machine, layer winding machine,straightening cutting machine and so on. Most the machines are automatic, high speed and effective. Our machines have been exported to South Korea,Malaysia, Russia,Kazakhstan,Tajikistan,Brazil,India,South Africa,Zimbabwe,Guatemala Egypt,Romania etc.All the products have gained the customers commend and approval in the world.
Main products Precision CNC parts , non-standard fasteners, customized sheet metal products, all kind of hardware products Material steel, stainless steel, brass, copper, aluminum, POM, nylon, PTFE Finish Polishing, anodize, nickel, zinc, tin, chrome Advantage best service, original factory, engineer support Machining equipment Automatic lathes, CNC lathes, cutting machines, welding machines, bending machines, printing lines Quality standard ISO 9001:2008; 100% check one by one Inspection equipment CMM, projection, calipers, micro caliper, thread micro caliper, pin, caliper, pass meter Lead time Sample 7-15 days, mass production 30-60 days. Packing According to customer's requirement Delivery Delivery goods by sea or by air, according to customer's requirement
Features: 1. Material: Zinc alloy; 2. Finish: Black acrylic with silver, gold, antique brass, antique copper, or light gun-metal; 3. Japanese MABUCHI motor with a durability of over 500,000 cycles; 4. Anti-tamper trim handle with free moving clutch mechanism; 5. Low power alarm, anti-tampering alarm; 6. System will be locked for 1 mins. after 5 continuous wrong input; 7. Password can be set with 6 to 10 digits. To avoid password being peeped, allow to max input 30 digits, as long as the correct password number is input in succession 8. User capacity: 10 passwords+ 990 fingerprints & cards+ 3 administrator(card, password or fingerprints); 9. Mechanical key unlocking is available for emergency; 10. Fingerprint Sensor: Biometric/ Semi-conductor.
1.Product name- zinc ingot 2.Place of Origin:china 3.Factory supply directly; Zn (purity): 98.7%-99.995%;4 4..Competitive price 1,High quality. 2,Competitive price 3,Steady supplying ability 4. Application: 1. Mainly used for die-casting alloy battery industry. 2.Widely used in Painting/ Printing/Dyeing/pharmaceutical/rubber industry etc. 3.Chemical industries, zinc and other metal alloy plating coating industry. 4.In zinc plating, manufacture of brass, maganese bronze, galvanized iron, dry battery; as catalyst and reducing agent. 5.Packaging: About 25Kg /Ingot, Packed in wooden case, Net weight 1000Kg/ Case,or as customer's requirements. 6.Shipping: with 15 days after receiving your T/T deposit or L/C at sight
1.Product name zinc ingot2.Place of Origin:china 3.Factory supply directly; Zn (purity): 99.99%-99.995%;4 4..Competitive price 1,High quality. 2,Competitive price 3,Steady supplying ability 4. Application: 1. Mainly used for die-casting alloy battery industry. 2.Widely used in Painting/ Printing/Dyeing/pharmaceutical/rubber industry etc. 3.Chemical industries, zinc and other metal alloy plating coating industry. 4.In zinc plating, manufacture of brass, maganese bronze, galvanized iron, dry battery; as catalyst and reducing agent. 5.Packaging: 28Kg /Ingot, Packed in strapping, Net weight 1200Kg/ Case,or as customer's requirements. 6.Shipping: within15 days after receiving your T/T deposit or L/C at sight Note: We can provide the products according to customers' requirements on size, weight, etc.
Approx. Price: Rs 406 / Piece Product Details: Minimum Order Quantity ; 100 Piece Ink Color : Blue Color ; Black Usage/Application : Writing and gifting Product Code : APPS-019 Model Number : Ap-019 Packaging Type : Box Packing Condition ; New Design : As per image Finishing ; Good Brand : PNP Material : Metal Body material ; Stainless Steel Use & Throw : No Occasion : Any Item Code : APPS-019 Pen Type ; Ball Pen Customized your pens for you and your clients with us. Ideal for gifting and promotions. Additional Information: Item Code: APPS-019 Production Capacity: As per order Delivery Time: 7-10 days
Type:BALL Structure:Deep Groove Applicable Industries:Building Material Shops, Manufacturing Plant, Machinery Repair Shops, Retail, Construction works , Energy & Mining Bore Size:64.99 - 65 mm Model Number:6213 LLU Precision Rating:P0, P6 ,P5, P4 ,P2 Seals Type:Open & ZZ & RS Number of Row:Single row Place of Origin:Shandong, China Product Name:Low Noise Deep Groove Ball Bearings 6213 LLU Bearing Price List Material:Chrome Steel Cage Material:Nylon & Metal Clearance:C2 C0 C3 C4 C5 Vibration:V1 V2 V3 V4 Noise Level:Z1Z2 Z3 Z4 Weight:0.989 kg Certificate:ISO9001:2008 MOQ:1 Piece Package:Plastic tube & According to client's requirements
COOLADEA Hot 12v Car Battery Portable Jump starter Gross weight: 1.3kg Material: Metal motor/pure copper cylinder Current: 2A Voltage: 12V Length of power cord: 2M Power supply type: TYPE-C USB ports Power: 120W Spec: Wireless model Net weight: 860g Type: Single cylinder Scope of application: All types of automobiles (excluding lorries and engineering vehicles of more than 5 tons), motorcycles, electric vehicles, all kinds of bicycles, all kinds of balls, balloons, life rings, swimming rings. Main scope of application: All types of automobiles (excluding lorries and engineering vehicles of more than 5 tons), electric vehicles, automobiles, motorcycles, bicycles length of inflatable tube: 25CM Additional function: Lighting, tire pressure gauge, warning light, USB charging
Model Number GY3040 Dimension 750*616*560mm Table size 400*590mm Acceptable material thickness 140mm Effective working area X290*Y390*Z90 Spindle motor 800w/1.5kw Water cooling spindle Drive mode Stepper Motor Max traveling speed 4000mm/min Carving speed 3000mm/min Machining accuracy 0.03-0.05mm Spindle speed 0-24000rpm/min Transmission XYZ axes use TBI ball screw Guide rail Linear optic axis guide rail Control System Mach3/Ncstudio Voltage AC220V/AC110V Frame structure Steel plate Compatible software Type3/ArtCAM/Castmate/JDPaintâ?¦ Weight 80Kg Application Woodworking, Metal, Plastic, Glass, Stone, Rubber, Advertising, Mould
Guangzhou Rambler pen Company which specialized in producing and exporting various of writting instruments such as advertising pen,ball pen,gel pen,roller pen,leather pen,wooden pen,banner pen,highlighter pen,laser pen,multipurpose pen as well as other customerized pen. We can print or engrave customers' logos or advertising on pens for promotion or gift. Product Name: touch pen MOQ: 5000pcs Material: plastic (ABS+ silica) / metal (copper, steel, aluminum) / Wood / ceramic Process: screen printing, pad printing, heat transfer printing, laser engraving, laser etching The pen body color: figure, provide the Pantone color color can be customized CONTACT:Emma WEBSITE:www.ramblerpen.com E-MAIL:info@ramblerpen.com
