Sodium Silicate Solution Suppliers and Manufacturers

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

Product Brief Introduction: with the largest consumption for construction and building materials. It is mainly used as enamel fluxing agent, glass opalizing agent, acid-proof clay, acid-proof concrete coagulator and wood preservative. It can also be used for insecticide. Product Hazard or Harmful Ingredients:It does not combust or explode but has corrosivity and certain toxicity. Product Physical Properties:The product is white powder crystals and basically neutral. It is difficult to dissolve in water and acid and the density is 2.37g/cm3. Product Chemical Properties:It is stable under normal temperature. It does not combust nor explode when it is heated or contacts with redox materials. Spillage Treatment Method:Simple cleaning and burying Protection Measures for Product Transport & Storage:To prevent from caking and going bad, it should be kept indoor or be covered with protection materials like canvas and free from the blazing sun. Packing :Knitted bags lined polyethylene plastic bags double packaging, Weighing 25Kg/50KG/1000Kg/1200kg. Other Information: Anti-caking agent can be added at the request of customers. Technical Specifications Analysis items Standard Na2SiF6 99% min Loss of weight on drying at 105â?? 0.3% max Free acid (as HCl) 0.1% max Chloride (as Cl) 0.1% max Sulphate (SO4) 0.3% max Iron(Fe) 0.02% max Water-insoluble matter 0.5% max Particle size distribution Passing through 40 mesh sieve 98% min Passing through 60 mesh sieve 90% min Passing through 325 mesh sieve 25% max

1. Product Functions and Features Sodium Selenite is a supplement of selenite for animal nutrition. The product has stable quality and good liquidity and is easy to mix process. 2.  Introduction Mixed feed additives and sodium selenite. The additive of microelement selenite in feed. Usage & Dosage:The recommended amount in the compound feed(calculated by Selenite mg/kg)0.1-0.3mg for livestock,0.1-0.3mg for fishes. 3. Appearance Light Grey Powder 4. Product quality standard 1%selenite 5%  selenite Sodium selenite (counted by Se)% 1 ±0.05 5 ±0.10 Moisture % 5 Pass 450 m test sieve% 95 Total arsenic content (counted by As)% 0.0005 Lead content (counted by Pb)% 0.002 Cadmium content (counted by Cd)% 0.001 5.Packing:25kg/bag 6. Storage conditions, methods and precautions: stored in cool and dry places, and used up as soon as possible once unpacked.

Product Name: Sodium permanganate Use level: Industrial Content: 40 (%) CAS Number: 10101-50-5 Molecular formula:NaMnO4 Molecular Weight: 141.93 Appearance: purple liquid. A density of 1.36 ~ 1.39 g / cm3, soluble in water, ethanol and ether, soluble in liquid ammonia. Decomposition in alkali. Strong oxidizing. And chemical properties similar to potassium permanganate. Purposes: as oxidants, disinfectants, fungicides and phosphorous antidotes. Toluene is also used to manufacture saccharin, o-toluene sulfonamide and organic synthesis and purification of phenol wastewater treatment. Can be used for circuit boards, metal surface cleaning, the conductive film cleaning to remove grease, electrolytic manganese dioxide, chemical fiber finishing, electroplating addition to hydrogen sulfide and other odors, as well as water treatment and so on. Packaging and storage: Industrial Pails barrel, net weight 25kg plastic drum, 250kg steel-plastic composite barrels, 1250kg IBC barrels packaging. Store in a cool dry place. Quality Standard:   Items index Sodium permanganate (NaMnO4) Content / (%) 40 Water-insoluble content / (%) 0.01 Potassium (K) content / (%) 0.22 pH value 6 ?8 Density / (g/cm3) 1.36 1.39 Chloride (Cl) content / (%) 0.02

Sodium chlorate Quality index: Control project Indicators Type Type grade qualified grade appearance White or yellowish crystals sodium chlorate(as dry basis), % 99.0 99.0 98.0 moisture, % 0.30 0.50 0.80 water insoluble, % 0.02 0.03 0.03 chloride( CL), % 0.20 0.20 0.30 sulfate(SO4), % 0.10 0.02 chromate(CrO4), % â?¤ 0.01 0.02 ferrum (Fe), % 0.005 0.05 To use: Used for manufacturing chlorine dioxide (can do tap water treatment), sodium chlorite and other chlorate, perchlorate Used in herbicide, oxidant, paper making, printing and dyeing, tanning leather, explosive, printing ink manufacturing Used for match, fireworks, medicine, metallurgical ore treatment and bromine extraction from sea water Packing:  25kg plastic woven bag 1000Kg woven bag

1,Name: Sodium nitrite Molecular formula: NaNO2 Formula weght:69.00 2Property: (1) ordinary sodium nitrite: white little crystals or light yellow  (2) dry powder sodium nitrate: white crystal,non-caking, showing loose status. Density:2.168. No odor, slightly salty. It is liable to deliquesce, dissolved in water,soluble in liquid ammonia,slightly soluble in ethanol and glycerin,Melting Point:271. Decomposition temperature is 320. It has oxidability and also has reducibility. It will slowly be oxidized into sodium nitrate in atmosphere, it can form nitrogen compound with nitrilo at low temperatures. 3Usage:It has been widely used in making nitro-compound and azo dye, mordant of textile dyeing, bleaching agent, metal heat finishing agent, cement early strength agent, and deicing agent etc. Note: The product should be stored in a cool, dry place to prevent it from moisture, heat and sunlight. This product can not be mixed with strong reductant, inflammable and explosive materials, food, feed and additives. â?¢ This product is toxic and should be properly kept and can not be eaten. 4 Specification: (Technical Standards:GB2367-2006) Item Unit Molten salt G High G First G Qualified G Dry powder G Assay % 99.3 99.0 98.5 98.0 98.5 Sodium nitrate % 0.6 0.80 1.00 1.90 0.80 Chlorides % 0.03 0.10 0.17 -- 0.1 Water insolubles % 0.02 0.05 0.06 0.10 0.06 Moisture % 1.0 1.4 2.0 2.5 0.2 Loose degree -- -- -- -- 95 5,Package: net 50kg net each in plasic woven inner plasic bag, or according to customers requirement.

1.Name: Sodium nitrate Chemical formula: NaNO3 Formula weght:84.99 2.Property: (1) ordinary sodium nitrate: white little crystals or light yellow (2) dry powder sodium nitrate: non-caking, showing loose status. Density:2.257. It is liable to deliquesce, dissolved in water, soluble in liquid ammonia, slightly soluble in ethanol and glycerin, Melting Point:308. While being heated up to about 380 it will decompose and release oxygen and turn into sodium nitrite,as the heating goes on, it will decompose into oxygen, nitrogen and nitrogen oxide. It has strong oxidability and can cause combustion explosion if being mixed with organic substance, sulfur, sodium nitrate etc. 3. Usage:  it has been wildly used in the glass industry, dye, dynamite, metallurgy, machinery, ceramic etc. 4. Specification: (Technical Standards:GB/T4553-2002) Item Unit High G. First G. Qualified G. Dry powder G. Assay % 99.7 99.3 98.5 99.3 Sodium nitrite % 0.01 0.02 0.15 0.02 Chlorides % 0.25 0.30 -- 0.25 Water insolubles % 0.03 0.06 -- 0.03 Moisture % 1.0 1.5 2.00 0.2 Carbonates % 0.05 0.10 -- 0.1 Iron % 0.005 -- -- 0.005 Loose degree -- -- -- 95 5.Package: net 25kg/50kg net each in plasic woven inner plasic bag,or 500kg net each in flexible container.

Analysis items Standard Result Appearance Yellow Crystalline Yellow Crystalline Purity 99% min 99.2% NaCN 0.01% min 0.001% Moisture 1.5% max 0.3% Water insoluble matter 0.02% max 0.01% Sulphate 0.3% max 0.05%

Inspection item Appearance White Granular Available chlorine Wt. % 60%MIN PH value (1% water solution) 5.5-7.0 Moisture (%) 5%MAX Granularity (mesh) 20-60mesh

Technical Specifications Na2SiF6 99% min Loss of weight on drying at 105 0.3% max Free acid (as HCl) 0.1% max Chloride (as Cl) 0.1% max Sulphate (SO4) 0.3% max Iron(Fe) 0.02% max Water-insoluble matter 0.5% max

Checking Item Test Standard Sodium oxide(Na2O)% 28.00-30.00 Silica(SiO2)% 27.00-29.00 Water insoluble% 0.2 Fe(ppm) 200ppm Whiteness% 80 Bulk Density 0.80-0.97g/cc PH of 1.0% Solution 12-13 Melting Point 72.2 ParticularSize % (16-30mesh) 90 98

Commodity: Sodium Hydrosulfite Other name: Synonyms: Sodium Hydrosulphite; Sodium Dithionite; Dithionous acid, Disodium salt; Sodium Sulfoxylate CAS No.: 7775-14-6 Molecular Weight: 174.10 Chemical Formula: Na2S2O4 Product Description Appearance: White, crystalline powder. Product Feature Odor: Slight irritative. Specific Gravity: Unavailable Solubility: Soluble in water. Density: 2.19 pH: 6-7 pH Test-Method: PH test paper. % Volatiles by volume @ 21C (70F): 0 Boiling Point: Not applicable. Melting Point: >300 C Decomposes. Vapor Pressure (mm Hg): No information found. Bulk Density: ~0.9 Evaporation Rate (BuAc=1): No information found. Application 1. Widely used in textile industry for vat dyeing, reduction cleaning, printing and stripping, textile textile bleaching . 2. bleaching paper pulps , especially mechanical pulps, its the most fittable bleaching agent in pulps. 3. bleaching kaolin clay, fur bleaching and reductive whitening, bleaching of bamboo products and straw products, 4. in mineral, the compound of thiourea and other sulphides. 5. as reducing agent in chemical industry. 6. Sodium hydrosulfite food additive grade is used in foodstuffs, as bleaching agent and preservative dried fruits, dried vegetable, vermicelli, glucose, sugar, rock sugar, caramel, candy, liquid glucose, bamboo shoots, mushrooms and canned mushrooms. Packaging 50kg/100kg net in iron drums with double PVC bags Product Specification/Models NDEX 90%, 88%, 85%. FOOD ADDITIVE Na2S2O4, 90%, 88%, 85%, Fe 20ppm ZincZnOther heavy metal calculated as Pb, 1ppm Water Insolubles05% Shelf Life(month)12

Commodity: Sodium Bisulfite Molecular Formula: NaHSO3 Molecular Weight: 104.06 Properties: White monoclinic crystalline powder with sulfur dioxide odor; relative density: 1.49; very easily soluble in water; can be decomposed when heated; slightly soluble in ethanol; aqueous solution is acidic; has strong reducing property; can be oxidized in the air or loose sulfur dioxide. Quality Standard: HG/T3492-80 Technical Indicator High-purity grade Acrylic grade Food grade Refined grade Industrial grade 1 NaHSO3 % 99.5 Insol. in water % 0.003, 0.005, 0.03, 0.04, 0.05 Chloride(Cl) % 0.003, 0.004 Iron(Fe) % 0.001 0.002 0.005 Heavy metal(Pb) 0.001 Arsenic(As) % 0.0001 Clarity test Qualified Use: It is used in the bleaching of cotton textiles; as reducing agent in dyes, paper-making, leather, chemical synthesis; in the manufacture of pharmaceutical intermediates, developer, food bleacher, antiseptic and anti-oxidants. Packing: In PP woven bag lined with PE bag; paper-plastic composite bag, and kraft paper bag etc. Net wt.: 25/50/1000 kgs/bag or upon clients' request.

Commodity: Sodium bicarbonate Synonym: Baking Soda; Bicarbonate of soda; Sodium acid carbonate; Monosodium carbonate; Sodium hydrogen International CHEMTREC , carbonate; Carbonic acid monosodium salt Molecular formula:NaHCO3 Molecule Weight:84.01 H.S code:28363000 CAS:144-55-8 Characteristics: White powder or tiny crystalls, nodorousand salty, easily soluble in water,insoluble in alcohol, presenting slightly alkalinity, decomposed when heating. Decomposed slowly when exposed to moist air. Quality Standard Item The National Standard The Total Alkalinity Content(NaHCO3)% 99.0, 100.5 Loss on Dring% 0.20 PH Value(10g/1) Solution, 8.6 Arsentic Content% 0.0001 Heavy Metal Content, 0.0005 Ammonium Salt pass Clearness pass Uses: food fermentation, feed addive, detergent ingredient, carbon dioxide foamer, pharmacy, leather, ore milling and metallurgy, detergent for wool, extinguisher and metal heat-treating, fiber and rubber industry, etc. Packing:25kgs or 50kgs plastic woven bags lined with one layer polythene bag. (We can meet with all your demands according with your need.)