Grade: 1. Carbon Black PL330J 2. Carbon Black PL330C 3. Carbon Black PL330C 4. Carbon Black PL550C 5. Carbon Black PL550B 6. Carbon Black PL550C 7. PL660B Beads 8. Carbon Black P330 9. Carbon Black P550 10. PL772B Beads Purity: 1.OAN (ml/100 gm) >90 2.OAN (ml/100 gm) >90 3.OAN (ml/100 gm) >95 4.OAN (ml/100 gm) >100 5.OAN (ml/100 gm) >100 6.OAN (ml/100 gm) >100 7.DBP No (OAN) (cc/100 gm) >100 8.DBP No (OAN) (cc/100 gm) >100 9.DBP No (OAN) (cc/100 gm) >105 10.DBP No (OAN) (cc/100 gm) >90 Actual price will be provided after your enquire.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
MOQ: 10,000 Barrels per Month Supply Ability: 1,000,000 Barrels per Month JP54 Technical Specifications: ADDITIVES Antioxidant in hydro processed fuel mg/l min 17 max 24 Antioxidant non hydro processed fuel mg/l max 24 Static dissipater first doping ASA- 3 mg/l max 1 Stadis 450 mg/l max 3 COMBUSTION PROPERTIES Specific energy, net mi/kg min 18.4 D 4808 Smoke point mm min 19 D 1322 Lumininomitter number min 45 D 1740 Naphtales % vol max 3 D 1840 Propriety unit min max result test ip method ASTM COMPOSITION Total acidity mg KOH /g max 0.01 354 D 3242 Aromatic % vol max 22.0 158 D 1318 Sulphur, total % mass max 0.30 107 D 1266/2622 Sulphur mercaptan % mass max 0.003 342 D 3227 Doctor test 30 D 4952 VOLATILITY Initial boiling point centigrade max report 123 D 96 10% vol at C 240 20% vol at C report 50% vol at C report 80% vol at C report End point centigrade max 42 170/303 D 56 / 3828 Density at 15 C kg m2 min /max 776/840 180/385 D 1298 LOW TEMPERATURES PROPERTIES freezing point centigrade max 40 15 D 1298 Corrosion copper (2hrs at 100 C) Corrosion silver (4 hrs at 500C) max 1 227 STABILITY Thermal stability control temp. 280C 323 Filter pressure, differential mm. Hg max 25 Tube deposit rating (visual) max
Ethanol alcohol distillation column 1. It is standard 95-96% alcohol equipment. Also it can distill pure water. 2.The distillation system has  three columns  and  continuous  distillation  process.The process is the  same as industrial(large scale) alcohol equipment.  Mash distillation  column distills  fermented  mash or light alcohol  to 50% alcohol ethanol . It has red copper bubble cap trays, standard design. It auto continuously feeds material liquid, auto continuously produces 50% alcohol ethanol and auto continuously discharges waste,  ethanol discharge in waste 0.05%, better than international standard requirements. The first rectification distillation  column  increases  alcohol degree  to 70-75% ,  separates  fusel oil and high boiling point  Impurities.  It auto discharges waste water,  ethanol discharge in waste 0.05%, better than international standard requirements. The second rectification distillation  column  increases alcohol degree to 95%,  separates low boiling point  impurities  like acetaldehyde and methanol . 3.  The rectification system uses  industrial(large scale) standard process, but the whole set alcohol equipments are installed in one frame, like integration  module, even  you can run it by a button.
Distillation column For Ethanol Alcohol Plant 1. It is standard 95-96% alcohol equipment. Also it can distill pure water. 2. The distillation system has three columns and continuous distillation process.The process is the same as industrial(large scale) alcohol equipment.     a. Mash distillation column distills fermented mash or light alcohol to 50% alcohol ethanol .  It has red copper bubble cap trays, standard design. It auto continuously feeds material liquid, auto continuously produces 50% alcohol ethanol and auto continuously discharges waste, ethanol discharge in waste ?¤0.05%, better than international standard requirements.     b. The first rectification distillation column increases alcohol degree to 70-75% , separates fusel oil and high boiling point Impurities. It auto discharges waste water, ethanol discharge in waste ?¤0.05%, better than international standard requirements.     c. The second rectification distillation column increases alcohol degree to 95%, separates low boiling point impurities like acetaldehyde and methanol . 3.  The rectification system uses  industrial(large scale) standard process, but the whole set alcohol equipments are installed in one frame, like integration module, even you can run it by a button.
2-head packaging machine (also can 4-18head according different capacity choice) Packaging speed 15bags/min Bag length 90-320mm Bag width 80-210mm Overall weight 400kg Power 1.8kw/220v Packaging capacity 20-1000ml Outer packaging size 820 x1220 x 2500mm Packaging form Back sealing This machine is an intelligent weighing automatic quantitative packaging machine with four scales and microcomputer control. Suitable for quantitative packaging of granular materials such as miscellaneous grains, nuts ,pesticides, fertilizers, veterinary drugs, premixes, additives, laundry detergent, salt, monosodium glutamate, white sugar, seeds, rice, snacks, hardware, etc. Performance characteristics: 1. High precision digital sensors enable precise measurement to be achieved instantly. 2. The microcomputer control system is technologically advanced, easy to operate, and more reliable to use. 3. Fast and slow vibration feeding, automatic correction of errors, achieving high-precision packaging. 4. Four scales work alternately, with fast packaging speed. 5. High quality stainless steel is used for the material contact part, which is anti-corrosion, dust-proof, and easy to clean. Host configuration: This machine is equipped with a dual CPU microcomputer control system, a 5-inch LCD display in Chinese or English, a user-friendly operation interface, automatic cursor detection and tracking, and simpler operation. Equipped with high-precision stepper motors to ensure the accuracy of the cutting position of each packaging bag.
Main features: 1. You can choose to use a single saw or a double saw for product stability, or a single saw for unstable products 2. Ensure the hygiene of the meat and ensure a smooth cutting surface 3. Waterproof design for quick cleaning 4. According to different uses, frozen meat, lamb chops, steak, fish 5. Adopting human-machine interface and intelligent operation panel 6. 30 sets of memory functions can be set 7. Feeding adopts servo motor, with high precision 8. The conveyor belt can be removed for cleaning Paramters : cutting thickness 1-50mm ,material thickness under 15cm . capacity 8-15times/min ,can adjustable.
Different capacity drying noodle making machine ,fresh noodle making machine long noodle making machine paste Italy noodle spaghetti making machine : Name Model & Parameters Qty set Note Automatic Hang Noodle Making Machine 5-260model, machine size 3*0.6*1.2m, voltage 380V,3KW, weight 440kg, capacity 150-200kg/h 1 Attached 3pcs cutter. 100 pcs hanging noodle poles Welcome order !
Beetroot Ethanol /Alcohol Process Machine Fuel /medical /food ethanol /alcohol process machine,ethanol/alcohol production line/process line ,ethanol /alcohol equipment ,ethanol/alcohol distillation machine ,ethanol /alcohol turnkey project 1. It is a turn key whole set equipment, simple equipment, less worker, less area, less cost. 2. Can produce 1000L-1000000L 96%-99.9% alcohol(ethanol) per day. 3. Can use Corn, wheat, cassava, molasses, rice, potato, date, beetroot, sugar cane ect which contains starch or sugar material. 4. We can do the turn key system or section part.
Corn ethanol /alcohol plant /production line welcome all friends all over the world ! Fuel /medical /food ethanol /alcohol process machine,ethanol/alcohol production line/process line ,ethanol /alcohol equipment ,ethanol/alcohol distillation machine ,ethanol /alcohol turnkey project 1. It is a turn key whole set equipment, simple equipment, less worker, less area, less cost. 2. Can produce 1000L-1000000L 96%-99.9% alcohol(ethanol) per day. 3. Can use Corn, wheat, cassava, molasses, rice, potato, date, beetroot, sugar cane ect which contains starch or sugar material. 4. We can do the turn key system or section part. 5. Can improve and rebuild old alcohol(ethanol) production line.