Builder S Hardware Construction Material Equipment Suppliers and Manufacturers

Bitumen Sheet

Tile Grout

Liquid Water Proof

Rockwool

Tile Grout

Rockwool, also known as mineral wool, is an insulation material made from natural stone or mineral fibers. The density of Rockwool refers to the mass of the material per unit volume, and it is commonly expressed in kilograms per cubic meter (kg/m�³) or pounds per cubic foot (lb/ft�³). The density of Rockwool can vary depending on the specific product and its intended application. Common densities for Rockwool insulation products range from approximately 40 kg/m�³ (2.5 lb/ft�³) to 200 kg/m�³ (12.5 lb/ft�³) or more. The choice of density often depends on factors such as thermal performance requirements, structural support needs, and the specific application of the insulation.

We have facade insulation board,terrace roof insulation board,partition wall,industrial insulation board,industrial rolls in our product portfolio.

We have all kinds plaster profiles like studs,tracks,omega,corner bead etc. with competitive prices.

Steel

GFRP rebar is made of high-strength glass fibers along with a highly durable resin. These products are developed as a superior alternative to steel in concrete reinforcement. It is widely used to reinforcing concrete in applications where it is exposed to water, salt water or chemical environments - Typical Advantages: - Non-Corrosive â?? It will not corrode when exposed to a wide variety of corrosive substances - including chlorides - High Strength-to-Weight Ratio â?? best reinforcement for weight sensitive reinforcement - Non-Conductiveâ?? It is excellent electrical and thermal insulator - Excellent Fatigue Resistanceâ?? performs best in cyclic loading solutions - Impact Resistanceâ?? It resists sudden and severe point loading - Magnetic Resistance â?? completely non-effective to electromagnetic fields; excellent for use in electromagnetic testing facilities - Light Weight easy to transport, no need for lifting equipment, easy to handle

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

Thermotax is a ready to use air setting refractory mortar. It is air setting mortar having good strength on air drying, forming strong joints & conferring an almost monolithic structure to the fire brick work. Moreover, it is highly suitable for Insulation brick lining work as well as refractory Brick lining work.

Refractory Mortar are heat resistance binding materials which are used in binding Refractory brick lining. Monolithic refractories include refractory castable, refractory mortar, spray mass etc. We offer two types of refractory mortar according to its application including Heat setting mortar : IS-6 Mortar, IS-8 Mortar, 40% To 90% Mortar Air setting Mortar : Set-50 Mortar, Set 50F Mortar

25/50 Kg BAG & 01 Ton Jumbo bag Refractor Castable are heat resistance binding materials which are used in binding Refractory brick lining. Monolithic refractories include refractory castable, refractory mortar, spray mass etc. We offer wide range of refractory castable such as : Conventional Castable Super Castable, Fire crete, HEAT - A Castable, HEAT- K Castable Low & Ultra Low cement Castable MON -45, MON-60, MON-70, MON-80, MON-90 Gunning Castable MONGUN-45, MONGUN-60, MONGUN-70 Insulating Castable INSUCAT-9, INSUCAT-11, INSUCAST-13, INSUCAST-15

Essential details Place of Origin: AUSTRIA Brand Name: contact to supplier Model Number: contact to supplier Packaging & delivery Lead time: Quantity(metric tons) 1 - 20 >20 Lead time (days) 5 To be negotiated