V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m�²/sec (max.) - Ph Value : 6.5 to 8.5
V3 Borewell Submersible Pumpset Falcon standard 73mm (3") Borewell Submersible pump is firmly coupled to a submersible electric motor which Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosion resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel (SS 204cu) shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 0.37 kW to 1.1 kW (0.50 HP to 1.5HP) - Version : Single Phase 160V to 230V, 50Hz, AC Supply - Speed : 2880 RPM - Head Range : 14 Mtr. to 96 Mtr. - Discharge Range : 70 LPM to 15 LPM - Outlet Size in Inch : 1.25" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Minimum cooling 1pH - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Falcon Premium 200 mm (8) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - SS-304 Grade investment casting bowl and SS-304 grade impeller in radial flow series - 20 Mtr. Head per stage in radial flow series - Specially designed high performance thrust bearing (SS-420 Tilting pad with carbon plate) to with stand axial thrust loads - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Special designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures services feasibility - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS Pumps are available Specification Direction of Rotation : Counter clockwise from driving end -1ph : Electrically Reversible -3ph - Power Range : 7.5 kW to 75 kW (10 HP to 100 HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Thrust Load : 7.5 kW -30 kW -10000 lbs - Speed : 2880 RPM - Head Range : 12 Mtr. To 440 Mtr. - Discharge Range : 2400 LPM to 300 LPM - Outlet Size in Inch : 4.0" & 5.0" - Degree of Protection : IP 58 - Minimum Cooling Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : Star Delta (SD) - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V7 Borewell Submersible Pumpset Falcon Premium 175 mm (7) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked in stainless steel stator shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Cast iron casting bowl and SS-410 grade impeller in mix flow series - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Dynamically balanced rotating parts ensures minimum vibration and longer life - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Special designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures services feasibility - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps Specification - Method of Starting : 3 ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 37.3 kW - Power Range : 11.2 kW to 37.3 kW (15 HP to 50 HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Speed : 2880 RPM - Head Range : 18 Mtr. To 650 Mtr. - Discharge Range : 1860 LPM to 55 LPM - Outlet Size in Inch : 2.0 , 2.5 , 3.0 & 4.0 - Degree of Protection : IP 58 - Direction of Rotation : Electrically Reversible -3ph - Thrust Load : 11.2 kW -37.3 kW -8000 lbs - Minimum Cooling Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
V4 Borewell Submersible Pumpset Falcon Premium 100 mm (4) Borewell Submersible pump is firmly coupled to a submersible electric motor and Operates by being submerged beneath the surface of the water. The optimal design of impeller and diffuser enables the best Possible hydraulic efficiency. Built-in check valve prevents back flow and reduces the risk of water hammering. All Vital components of these pumps are made up of corrosive resistance thermoplastic and the shaft is of SS 410. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - Motor portion covered with corrosive resistance Stainless steel J4 shell - More durability and hygiene - High operating efficiency - Specially designed thrust bearing to withstand high axial thrust load - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps. Specification Power Range : 0.37 kW to 4.4 kW (0.50 HP to 6.0 HP) - Version : Single Phase 160V to 230V, Three Phase 350 to 415V, 50Hz AC Supply. Single Phase available in 0.5 HP to 5.0 HP Three Phase available in 1.0 HP to 6.0 HP - Speed : 2880 RPM - Head Range : 10 Mtr. To 340 Mtr. - Discharge Range : 450 LPM to 12 LPM - Outlet Size in Inch : 1.0 , 1.25, 1.5 & 2.0 - Degree of Protection : IP 58 - Direction of Rotation Minimum Cooling : Counter clockwise from driving end -1ph: Electrically Reversible -3ph - Thrust Load : 0.37 kW â?? 0.75 kW- 650 lbs, 1.1 kW -1.5 kW -1000 lbs, 2.2kW, 7.5 kW -1500 lbs. - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR): 3ph Direct Online (D.O.L) - Maximum Starts Per Hour : 20 Times
V9-V10 Borewell Submersible Pumpset Falcon Dlx. 250 mm ( 9 & 10) Borewell Submersible Pumpsets are powered by water filled, rewindable submersibleMotor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressureand rigidly locked in stainless steel stator shell. T-Bolt design in all motor ensures rigid construction. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles Salient Features - SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow MRS series 27Mtr head per stage in radial flow series. - FG 250 Cast Iron Bowl with CED Catted and SS-304 Grade Impeller in Mix flow FMC Series 22Mtr head per stage in Mix flow series. - Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads. - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set. - Dynamically balanced rotating parts ensures minimum vibration and longer life. - Designed for wide voltage fluctuations. - Motor portion covered with corrosive resistance Stainless steel (SS 304) shell. - More durability and hygiene & High operating efficiency. - Specially designed thrust bearing to withstand high axial thrust load. - Extremely hardwearing water lubricated bearing. - Thread type motor construction ensures service feasibility. - Designed for wide voltage operation. - Best alternative for JET & Compressor pump set. - Additional intermediate bearing in higher stage pumps. Specification - Power Range : 55 kW to 112 kW (75 HP to 150HP) - Version : Three Phase 350 to 415V, 50Hz AC Supply - Speed : 2900 RPM - Head Range : 12 mtr. To 300 mtr. - Discharge Range : 3600 LPM to 960 LPM - Outlet Size in Inch : 4.0" & 5.0" - Degree of Protection : IP 58 - Maximum Starts Per Hour : 10 Times
V5 Borewell Submersible Pumpset Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell. Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5 , 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m/sec (max.) - Ph Value : 6.5 to 8.5
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell Pump Liquids - Clean - Thin - Non-Aggressive - Non-Explosive - Clear - Cold - Fresh water - Without abrasives - Solid particles. Salient Features - SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series) - 9 Mtr. Head Per Stage In Radial Flow Series. - Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads. - Dynamically balanced roating parts ensure minimum vibration and longer life - Motor Portion covered with corrosion resistant S.S. J4 shell - More durability and hygiene - High operating efficiency - Extremely hardwearing water lubricated bearing - Thread type motor construction ensures service feasibility - Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pumpset - Designed for wide voltage operation - Best alternative for JET & Compressor pump set - Additional intermediate bearing in higher stage pumps - Fully SS pumps are available in (GRS - Series) Specification - - Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP) - Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply (Single Phase available in 3 HP to 5 HP) - Speed : 2880 RPM - Head Range : 12 Mtr. To 640 Mtr. - Discharge Range : 690 LPM to 80 LPM - Outlet Size in Inch : 1.5, 2.0" & 2.5" - Degree of Protection : IP 58 - Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph - Thrust Load : 2.2 kW â?? 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs - Flow Along the Motor : 0.15 m/sec. - Type of Duty : S1 (Continuous) - Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2 kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star Delta (SD) upto 9.3 kW - Maximum Starts Per Hour : 20 Times Characteristics Of Clear Cold Water - Maximum liquid temperature : 33C max - Permissible amount of sand : 25 g/m - Allowable solids : 3000 ppm (max.) - Chloride ion density : 500 ppm (max.) - Turbidity : 50 ppm silica scale (max.) - Hardness (Drinking Water) : 300 ppm (max.) - Specific gravity : 1.004 (max.) 6 - Viscosity : 6 1.75 x 10 m²/sec (max.) - Ph Value : 6.5 to 8.5
1. Characteristic: It is a white and colloidal micro-particle with its primary micro-particle from 5-40 nm and has obvious properties such as thixotropy, reinforcing, thickening and filling etc. and is insoluble in all kinds of solvents and liquids except hy-drofluoric acid and concentrated bases. 2. Specification: Q/SHG19-2008ItemIndex Product: LM200 Apparent: White solid colloidal micro-particle Specific surface area m2/g: 150�±15 PH value3.6~4.3 Heating loss weight % (m/m) â?¤1.0 Burning loss weight % (m/m) â?¤1.0 Apparent density g/Lâ?¤60 3. Uses: It is used widely in silicone rubber, construction sealant, coating, electron and electric, aerospace, medicine and medical material, resin processing, printing ink, pesticide and other industries. LM-150: used widely in silicone acid rubber, sulfurized silicone rubber in ambient temperature (low water content), silicone neutral rubber. LM-200: used widely in sealing ring, sealing gasket, petroleum pipeline, insulator, tablet powdered preparation, artificial viscera, infusion tube, latex nipple and high quality oil ink. LM-300: used widely in resin thickener, thickness agent for synthetic lubricating ester, resin thixotropic agent for electronic component. LM-380: used widely in reinforcing agent for silicone rubber, medical silicone rubber for transparent artificial organs and artificial heart etc. 4. Packing: packed with multi-layer paper plastic compound bag with net weight of 5 kg or 10 kg, or packed by whole plastic seal for users having special demand on water content. 5. Store and transport: placed in vent and dry storehouse and prevented from humid, water, pressure and throwing during transport.
D G EXIM is well positioned in the water treatment business and technically geared to tailor-make solutions to any water treatment requirements. Every situation is analyzed based on the elements present and a unique solution is offered. We supply chemicals for Boiler Treatment, Cooling Tower and Portable Water Treatment as well AS Effluent Treatment. Below you will find some of the water treatment chemicals we supply Aluminum Sulphate Flocculant Ferric Chloride Ferric Sulphate Ion Exchange Resins Calcium Hypochlorite 65% Sodium Hypochlorite 15% Hydrogen Peroxide 50% Hydrochloric Acid Phosphoric Acid Sulphuric Acid Bac 50 / 80 Activated Carbon Poly Aluminium Chloride (P.A.C) Chlorine Gas Sodium Sulphite
Specifications Drained Copper Compressor â?? Fridges/AC (RAINS per ISRI Specifications). Our copper content on 99.97 % Monthly Supply Capacity: 500 - 1500 metric tons, Type: Fridges, AC. Packaging Detail: Wood Pallets, 20(40) FCL/ According to ISRI Specification in Containers Quantity: Between 200~500MT per month Minimum Order acceptable 1x20FCL (25MT or 26MT/20FCL, 3000 or 3450 Pieces/20FCL
We supply specialized  manufactured Shell amp Tube Heat Exchangers amp Pressure Vessels Delivering superior quality products in minimum delivery time MOC we can supply in copper brass carbon steels stainless steels like SS304 SS310 SS316L copper alloys such as cupro nickel Admiralty amp Aluminum Brass and many other materials We can supply Heat Exchangers amp Pressure Vessels up to 40 Tons The product range includes the proprietary plate fin tube heat exchanger oil coolers inter coolers after coolers marine heat exchangers oil cooling systems condensers chillers economizers super feed heat exchangers receivers and surge drums This products are extensively used in oil and gas refineries air separation plants chemical steel refineries pharmaceutical industries air conditioning amprefrigeration plants heat treatment shops marine engines amp gear boxes induction furnaces machine tools diesel engine generating sets compressors power plant installations transformers hydraulic power packs food processing vegetable oil refining amp sugar industry etc We are supplying this with certifications such as U R amp NB Stamp from ASME ISO 90012008 quality certificates from LRQA and certifications from DGQA IRS NSIC etc This are all manufactured in Nondestructive testing such as Visual Inspection Liquid penetrant testing Radiographic testing Tube to Tube sheet Weld radiography Ultrasonic testing for raw material and welds Helium leak testing Bubble Leak testing Magnetic particle testing
A gasket is a mechanical seal which fills the space between two or more mating surfaces, generally to prevent leakage from or into the joined objects while under compression. Metallic Gaskets: \"Metallic Gaskets\" are gaskets that are fabricated from one or a combination of metals to the desired shape and size. Common metallic gaskets are Spiral Wound Gaskets, Double Jacketed Metal Gaskets, Solid Metal Gaskets, Corrugated Metal Gaskets, Ring Type Joint Gasket used for heat exchangers, compressors, condensers, pumps, valves and turbines. These metallic gaskets are suitable for high pressure & temperature applications and require high bolt load to seal. Types: � Spiral Wound, Double Jacketed, Solid Metal gaskets, Corrugated Metal Jacketed Gaskets, Ring type joint Gaskets Non Metallic Gaskets: \"Non Metallic Gaskets\" or \"Soft Gaskets\" are gaskets that are easily compressed under a low bolt load. They are composite sheet materials that are suitable for a wide range of general as well as corrosive chemical applications. They are easily available either in sheet form or as gaskets that are cut accurately to any reasonable shape and size. Non metallic gaskets are usually manufactured from materials like arimid fiber, glass fiber, elastomers, teflon (PTFE), compressed asbestos fibre (CAF), flexible graphite etc. Types are: Non Asbestos, Asbestos, Flexible Graphite, PTFE, Viton, Silicone Rubber, Neoprene and Flange Gaskets.
We can supply tanks and vessels required for storage and transportation tanks of various liquids and gases like LPG, PROPANE, PROPYLENE, AMMONIA, LIQUIDCARBONDIOXIDE, CHLORINE , HYDROGEN, NITROGEN, OXYGEN, ARGON, SULPHUR DIOXIDE, BUTADINE, ETHYLENE OXIDE AND OTHER GASES , in a wide range of various capacities for use in domestic, industrial and transportation sectors. The manufacturing of these tanks requires special expertise , technology and strict quality control measures. These tanks are manufactured confirming to various design standards like ASME SECT VIII DIV I & II, AD- MERKBLATTER, PD5500, IS2825 and under the stagewise inspection of various third party inspection agencies like DNV, BVIS, TUV, LLOYDS ,PDIL and others. We also supply a wide range of Process Plant Equipments such as Coded Pressure Vessels, Distillation Columns, Towers, Reactors and Heat Exchangers. Also we undertake turnkey projects to construct Fixed & Floating Roof Tanks, Mounded Storage Tanks and Plant Piping.
Propylene carbonate (molecular formula: C4H6O3) is a colorless, odorless, flammable liquid. Miscible with ether, acetone, benzene, chloroform, vinyl acetate, etc., soluble in water and carbon tetrachloride. It has a strong ability to absorb carbon dioxide and is stable in nature. In industry, it is obtained by adding propylene oxide and carbon dioxide under a certain pressure, and then distilling under reduced pressure. It can be used as oily solvent, spinning solvent, olefin, aromatic hydrocarbon extractant, carbon dioxide absorber, dispersant for water-soluble dyes and pigments, etc. Application 1. It can be used as an excellent medium for high-energy batteries and capacitors in the electronics industry. 2. In the polymer industry, it can be used as a solvent and plasticizer for polymers. 3. Used as a plasticizer for adhesives and sealants. 4. It can also be used as a phenolic resin curing accelerator and a dispersant for water-soluble adhesives, pigments and fillers. 5. The chemical industry is the main raw material for synthesizing dimethyl carbonate. It can also be used to remove carbon dioxide and hydrogen sulfide from natural gas and petroleum cracking gas. 6. It can also be used in textile, printing and dyeing and other industrial fields.
1. Why choose us? 1. Experienced cng compressor manufacturer for over 16 years. 2. A turn-key cng station solutions supplier. 3. Always meet customer's high request. 4. A large stock of spare parts. 5. Oversea technical service team. 6.We are manufacturer, with professional trade company. 7. Good quality, very competitive price. 2. Business scope 1. Supply the complete equipments for cng and lng station. 2. Provide turn-key cng station solutions. 3. Customized design and oem service. 4. Supply kinds of industry compressors. 5. Oversea door to door installation&training service. 6.A large stock of spare parts for good after-sale service. 3. Description of z-type compressor 1. Small location area and stable operation. 2. Vertical reciprocating piston compressor with large discharge capacity range. 3. Oil-free lube structure design and operation. 4. Balance section compressor technology and high pressure packing seal technology. 5. Skid mounted compressor unit, convenient transportation and installation. 1. If the compressor can enter into container, we adopt simple and rain-proof package. 2. If the compressor can not enter into container, the goods will be transported by train or other way, we adopt wooden or iron plate package.
Haynes 718 alloy is a precipitation-hardening nickel-chromium alloy that offers high strength, toughness, and resistance to corrosion and high-temperature environments. It was developed in the 1950s for use in gas turbine engine components, and has since found a wide range of applications in other high-stress industries such as aerospace, nuclear, and chemical processing. The alloy is characterized by its excellent mechanical properties, including high tensile and yield strength, good ductility and toughness, and resistance to fatigue, creep, and stress-corrosion cracking. These properties are achieved through a combination of precipitation hardening and solid-solution strengthening, which involve heat treatment processes that cause the formation of fine, uniform precipitates within the metal matrix. Haynes 718 alloy also has good resistance to oxidation and other forms of corrosion, particularly in high-temperature environments. It is capable of maintaining its properties at temperatures up to around 1300�°F (700�°C), making it suitable for use in hot sections of gas turbine engines, nuclear reactor components, and other high-temperature applications. In addition to its mechanical and corrosion resistance properties, Haynes 718 alloy also has good weldability and machinability. It can be readily welded using a range of methods, and can be easily machined using standard metalworking techniques. Overall, Haynes 718 alloy is a versatile and reliable material that has proven itself in a wide range of demanding applications. Its combination of high strength, toughness, and resistance to corrosion and high-temperature environments make it an ideal choice for use in critical components where reliability and performance are paramount. Haynes 718 alloy standards vary by country. Here are some of the common ones: United States Standards: AMS 5596: Standard Specification for Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate, Haynes 718 AMS 5662: Standard Specification for Nickel Alloy, Bars, Forgings, and Rings, Haynes 718 AMS 5663: Standard Specification for Nickel Alloy, Bars, Forgings, and Rings, Haynes 718 (UNS N07718) AMS 5664: Standard Specification for Nickel Alloy, Bars, Forgings, and Rings, Haynes 718 (UNS N07718) AMS 5832: Standard Specification for Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire, Haynes 718 AMS 5962: Standard Specification for Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings, Haynes 718 AMS 5838: Standard Specification for Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire, Haynes 718SPF We can provide the following the prodcuts:Haynes 718 alloy coil; Haynes 718 alloy strip;Haynes 718 alloy plate; Haynes 718 alloy sheets; Haynes 718 alloy tube; Haynes 718 alloy pipe;Haynes 718 alloy flat; Haynes 718 alloy bar GB/JIS:NW7718/UNS:NW7718/W.Nr:2.4668