APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
PRODUCT DATA SHEET ACID RESISTANT BRICK Material : RED SHALE Type Acid Resistant Brick Size (mm) 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions Heavy thermal shock Typical Physical Properties of GANESHAS Acid and Chemical Resistant Brick Characteristic RED SHALE ACID RESISTANT BRICK Test Standard Bulk Density, gm/cc - 2.3 to 2.35 ASTM C-20 -Water Absorption, % - 0.1 to 1.5 IS 4860-1968 Apparent Porosity, % -0.5 to 1.75 S 4860 Acid Solubility (H2SO4), Loss in Mass,% -0.1 to 1.8 ASTM C-279 Modulus of Rupture, PSI -2133 to 3555 ASTM C-67 Compressive Strength, Kg/cm2 - 700-900 IS 4860-1968 Abrasion Resistant , Volume in mm3 -69 to 85 EN 102 Surface Hardness, MOHS Scale - 7
PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103
Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.
Brand waterproof membrane of elastomer (SBS) modified asphalt is a kind of windable sheet waterproof material, which adopts styrene-butadiene-styrene (SBS) modified asphalt as a dipping and covering modifier, whose upper surface is coated by PE film, fine sand, mineral granules or aluminum foil, copper foils or other isolating materials. Features Spunbonded polyester fiber membrane;aintegrated advantage properties of spunbonded polyester substrates and SBS modified asphalt, wonderful integrated properties. It could form waterproof layer, which has high strength and good property to stand against water pressure; High tensile strength and elongation rate, strong adaptability for substrate shrinking distortion and cracks; Good high and low temperature resistance, could keep its functions at -50; and be used in cold or hot areas, especially in cold areas; Resistance to puncture, pressing and rubbing, tearing, and wearing; Good resistance to corrosion, mildew and weathering; Good construction performance, with firm and enduring joints. Application Range It could be widely used in all kinds of waterproof engineering projects in all fields, especially in the following types of engineering projects: All kinds of building roofs engineering projects, exposed, non-exposed, heat preservation, non-heat preservation, planting building roofs and roof parking lots; All kinds of underground waterproof or damp proof engineering projects; Bridge surfaces of subways, tunnels, concrete roads, sewage treatment and garbage burying projects; water spraying pools, swimming pools, penstocks, water pools, and so on.
Bitumen, often referred to as asphalt, is a viscous, black, and sticky substance. It is a semi-solid form of petroleum and is primarily used as a binder in road construction. When mixed with aggregates, it forms asphalt concrete, the material commonly used for paving roads. Primary Characteristics: Appearance: Thick, black to dark brown substance. Temperature Sensitivity: Becomes liquid when heated and returns to a semi-solid state upon cooling. Water Resistance: Acts as a waterproofing agent, making it ideal for various sealing applications. Adhesion: Excellent adhesive properties, allowing it to bind aggregates together effectively. Grades & Types: Bitumen comes in various grades, primarily determined by its viscosity and penetration value. Common types include: Paving Grade Bitumen: Used in road construction. Oxidized Bitumen: Produced by air blowing and has stiffer properties. Cutback Bitumen: Bitumen diluted with solvents to reduce viscosity for specific applications. Modified Bitumen: Bitumen altered with polymers to enhance its properties. Applications: Road Construction: Mainly used as a binder mixed with aggregates to pave roads. Roofing: Used as a waterproofing agent in roofing felts. Dams & Reservoirs: Acts as a waterproofing membrane. Soundproofing: Used in soundproofing materials due to its insulating properties. Advantages: Durability: Offers a long-lasting paving solution, able to withstand various weather conditions. Cost-effective: Provides a reliable and economical material for large-scale infrastructure projects. Recyclable: Old bituminous roads can be reprocessed to produce new roads.
I am Beijing Nimble bitumen membrane equipment CO.LT.We are mainly specialized in research,development and manufacture of equipment for bitumen membrane.Our company was established in 1991.It acts as the leading supplier of equipment for bitumen membrane in China, and a newborn force in international equipment industry for bitumen membrane.Beijing Nimble waterproofing membrane Corporation had focused on offering quality goods and on-time service,We can according to customer requirement to produce different types equipment from the small equipment to ten million ©O . Until now, we had served hundreds of customer from more than 10 countries in the world. Our equipment has exported to India,Russia,UKrine,Saudi Arabia ,North Korea,and We have a branch company In India now. ART 1 General information Technical parameters 1Production capacity: annual production of modified bitumen membranes of 3 million Sqm (16 hours/day, 300days/year with two shifts) Reinforcement: Polyester, Glass fibre Modified materials : SBS, APP 4Materials for surface: sand, scraps of stone, PE membrane, aluminum foil, etc. 5Specification of products: Width: 1m, thickness: 2-5mm, length: 7.5 or 10m 6Production speed: 0-20m/min¡£ 7Main workshop: 60¡Á (12-15) ¡Á£¨6-8£©m Labor required 5-7 workers are needed for the whole production line Boiler room: 2workers Modified workshop: 1-2 workers Production workshop: 2-3 workers Utilities Electricity: Alternating current, 380V50Hz60Hz Water Consumption: 2-3 T/D
Ask about your requirements Pallets, rolls of 1m w x 10m l
Bitumen is known for its waterproofing and adhesive properties and is commonly used in the construction industry, notably for roads and highways. Production occurs through distillation, which removes lighter crude oil components like gasoline and diesel, leaving the heavier bitumen behind. Bitumen deposits can also occur naturally at the bottom of ancient lakes, where prehistoric organisms have decayed and been subjected to heat and pressure.
Based on SBS modified bitumen waterproofing membrane, it uses butyl and butylbenzene as the self-adhesive material. Advantage: 1. Convenient construction due to cold application. 2. Excellent adhesion to the base. 3. High tensile strength and elongation. 4. Excellent tear and weather resistance. Application: Roof and basement of industrial and civil buildings, municipal engineering, reservoir and swimming pool. Specification: 1. Thickness: 3/4/5mm 2. Width: 1000/2000mm 3. Length: 10m
This kind of waterproof coiled material is made in the following way: base materials are firstly dipped into asphalt or thermoplastic elastomer (e.g. SBS), thermoplastics (e.g. APP or APAO) and modifiedasphalt; then both surfaces are coated with elastomer or plastic asphalt; fine sands and mineral grains (pieces) or polyethylene memb ranes are spread or covered on its upper surface; fine sands or polyethylene membranes are spread or covered on its lower surface. Product Feature * It has good waterproofing and ageing-resistance function; * Not flowing at highest temerature and no crack at lowest temperautre; * Easy application, no pullution; * Long service life; Matters need attention * no construction shall be allowed on rainy, snowy or windy days above grade 5; * construction site and personnel safety protection facilities are complete, fire fighting equipment is effective and placed according to regulations;
Technical Data Sheet Of Accoset-50 ALUMINA MORTAR (Test Certificate) General Properties A. Max service temperature - 1500 oC B. Maximum grain size - 0 - 1.5 mm C. Water required for mixing - 22 - 30% D. Setting - Airsetting E. Sintering Temp - 1550 oC Chemical Properties A. Al2O3 - 50.00% B. SiO2 - 31.00% c. Fe2O3 - 5.00% D. LOI - 7.00% Physical Properties A. Dry Density - kg / m3 B. CCS - 17 kg / cm2 after drying at 110C / 24 hr C. MOR - 20 kg / cm2 at 110 oC/ 24 hr 18 kg/cm2 at 800 C/ 3 hr Thermal Properties - A. Refractoriness ( Orton / C) - 31.5 orton cone/1699 oC Packaging - 25 - 50 kg bags Storage Life - 12 months Delivery State - Dry
Bitumen a black viscous mixture of hydrocarbons obtained naturally or as a residue from petroleum distillation. It is used for road surfacing and roofing. Bitumen is a mixture of Organic Liquids that are highly Viscous, Black, Sticky, Entirely Soluble in Carbon Disulfide, and composed primarily of highly condensed Polycyclic Aromatic Hydrocarbons. Naturally occurring or crude bitumen is a sticky, tar-like form of petroleum which is so thick and heavy that it must be heated or diluted before it will flow. At room temperature, it is much like cold molasses. Refined Bitumen is the residual (bottom) fraction obtained by fractional distillation of crude oil. It is the heaviest fraction and the one with the highest boiling point, boiling at 525 C (977 F). Petroalliance are involved in import and the supply and trade of Bitumen Oil. This oil is a dark and viscous liquid which is sticky in texture. It is widely used in road construction, waterproofing, paints, enamels etc. It is available to clients in different types of settings at highly affordable prices. It is widely acclaimed amongst our client base for its supreme quality. Uses of Bitumens Bitumen is primarily used for construction and paving of roads. Its other uses are for Bituminous Waterproofing Products, including the use of bitumen in the production of roofing felt and for sealing flat roofs.
Name is sbs modified bitumen waterproof membrane. Thickness is 3mm. Reisitance temperature is -5 degree celsius. Length is 10 meters. Width is 1 meter. z
1121 parboiled rice, 1121 white and sella rice, or ir64 white and parboiled rice, all types of basmati and non basmati rice, corn (maize), corn flour, brown cumin, black cumin, cardamom, dry red chili, chili powder, raw sulphur, hulled white sesame seed,, poppy seed, all types and sizes floor ceramic tiles in all size, all type wall tiles in all size, all types of front elevation tiles, all type of marble & granite, all type of poly pvc door window frame, all type waterproof door, all type bathroom door, all types of sanitary ware like a washbasin, toilet seat urinal seet and other all sanitary ware. door frame (poly pvc), d6 diesel, dap fertilizer, urea fertilizer, bitumen, en590 10ppm diesel, jet a1 fuel, chicken paw, chicken feet , other chicken part, whole chicken, any grade steem coal and charcoal, d2 gas oil, liquefied natural gas, liquefied petroleum, mazut m100, aviation kerosene colonial grade 54 and all type date , dates.
Vanilla bean, vanilla powder, aluminum design radiators, bituminous membranes for waterproofing, glass wool for heating insulation , stone wool for heating insulation, extruded polystrene (xps), talc powder, cashew nut, .blackpepper, singing bowl, condensing wall hang gas boiler, conventional wall hang boiler, hand made wooden art, aluminium and glass veranda room and garden room, dehumidifiers for industrial and swimming pool , smart controlled air conditioning, heat pumps.
Two kinds of surface material: PE and AL. Tension: N/5CM no less than 130 & 100 Standard export packing
Product Details: Storage : Dry Place Density : 1000 Kilogram per cubic meter (kg/m3) Grade : Industrial Grade Application : Industrial Supply Ability : 2500000 Kilograms Per Month Price And Quantity Minimum Order Quantity : 50 Kilograms Product Specifications Storage : Dry Place Application Industrial Density : 1000 Kilogram per cubic meter (kg/m3) Grade : Industrial Grade Trade Information Payment Terms : Cash in Advance (CID) Supply Ability : 2500000 Kilograms Per Month Delivery Time : 1 Week Main Domestic Market : All India Product Description Industrial Bitumen we offer has multiple uses in industries with wide range of applications. It has all major traits such as plasticity, adhesion, resistance to acids, waterproofing and more. This is an inexpensive as well as safe material to be used in various industries. It is used in construction industry, making roads, roofing and more. The major usage of Industrial Bitumen is in road construction as it is cost effective as well as durable when used with concrete.
