Wire Gauge: single steel diameter size 1.4-4.8mm Standard: AISI,ASTM,BS,GB,JIS Alloy Or Not: Non-alloy Type: Galvanized Place of Origin: India and China
Wire Gauge: 0.2-160mm Standard: AISI,ASTM,BS,DIN,GB,JIS Application: Construction, Manufacturing, Rope, Alloy Or Not: Non-alloy Steel Grade: Q195/Q235/SAE1006/SAE1008 Origin : India and China
Special Use: Cold Heading Steel Wire Gauge: 0.15mm to 16.00mm Application: Fencing Alloy Or Not: Non-alloy Type: Spring Steel Grade: SAE1010 SAE1045 SAE1060 65Mn 72A 82B Origin : India and China
Wire Gauge: 0.20mm-12.50mm Standard: AISI,ASTM,BS,DIN,GB,JIS Application: Construction Alloy Or Not: Non-alloy Steel Grade: 30MnSi, SAE1060, SAE1065, 65Mn, SAE1070, 72A B,SAE1080,82A/B,C82DA Place of Origin: India and China
We are exporter of Ferro Vanadium. Ferro vanadium consist of vanadium and iron, mainly used as alloys in steel-making additives, high ferro vanadium alloy is also used as a additive. Commonly used vanadium iron containing vanadium 40%, 60% and 80% of three.
Wire Gauge: Dia: 0.5mm-5.0mm Standard: AISI, ASTM, BS, DIN, GB, JIS Application: Manufacturing Steel Grade: Alloy 42,48,52
We are exporter of Ferro Chrome. We supply the Quality Ferro Alloys Like Ferro Chrome HC Cr 60% min Si 3.50% Max C 8.50% MAX S 0.05% Max P 0.04% Max
Ramming mass is commonly used in metallurgy, building materials, non-ferrous metal smelting, chemical, machinery and other manufacturing industries. Ramming mass is widely used in non-core intermediate frequency furnace and core induction furnace. As an intermediate frequency furnace ramming material, refractory ramming is applied to melt gray cast iron, nodular cast iron, malleable cast iron, vermicular cast iron, and cast alloy steel; to melt carbon steel, alloy steel, high manganese steel, tool steel, heat resistant steel, stainless steel, molten aluminum and its alloys; to melt red copper, brass, white brass, bronze and its alloys, etc. Induction furnaces are used for melting cast iron, mild steel and various alloy steels in foundries and making of steel in mini steel plants using sponge iron The refined high silicon, low iron quartz sand and quartz powder are selected and the fused quartz sand is added as the refractory material., with no slag, no crack, damp proof, convenience of repair, and the corrosion resistance, thus greatly improving the furnace service life span and the economic benefit.. Silica ramming mass can safely be used up to an operating temperature of 1600 deg C. Since it expands very little, it is superior to both alumina and magnesia refractories to resist thermal shocks Acid ramming material is the premixed ramming mass of the lining material. The acid ramming mass is used to smelt a series of metal materials such as ordinary steel and carbon steel. The lining practice best suited to a particular furnace depends upon the capacity and design of the furnace, operation practice adopted during making of a heat, and furnace output.
We are supplier and exporter of Ferro Silicon. Ferro silicon Specs: Si:75%min. and Si:72%min. C:0.2%max. S:0.02%max. P:0.04%max. Al:2.0%max.1.5%max.and 1.0%max .Commodity: Ferro Silicon Low Al Specs: Si:75%min. C:0.2%max. S:0.02%max. P:0.04%max.Al:0.1%max.0.3%max.and0.5%max. In 1mt plastic woven bags. Ferro Silicon Ferro Silicon has a melting point of 1200�?�°C to 1250�?�°C with a boiling point of 2355�?�°C and Ferro Silicon contains about 2% of calcium and alluminium. Ferro Silicon, as an additive to the production process of ferrous metals, will impart several desirable properties upon the resultant alloy. Some of the primary benefits of adding Ferro Silicon to an alloy is to improve the corrosion resistant properties of the new compound, as well as to add to the high temperature heat- resistance properties of the new alloy, for example, in the production of silicon steel for use in transformer cores.
DESIGN Classic long tassel ethnic style dangle earring design, never out of date. Triangle drop earring: 4.9 x 4.3cm, Oval dangle earrings: 6.6 x 3cm, Rhombic drop earrings: 6.9 x 3.8cm, Lightweight and eye-catching. WEAR FEELING - Study safe ear pin, no worry about allergies, comfortable to wear, longer time to use. MATERIAL - Antique alloy stud earrings, allergy free and does not readily corrode, rust. Light-weight and graceful.
We supply the Quality Ferro Alloys Like Ferro Manganese HC / MC / LC Grade I II III Mn 65% min 70% Min 75% Min Si 2% Max 2% Max 1.50% Max C 8% Max 8% Max 8% Max S 0.05% Max 0.035% Max 0.03% Max P 0.40% Max 0.30% Max 0.25% Max MC FeMn Mn 70%Min /75% Min / 78% Min Si 1.50% Max C 1.50% MAX S 0.03% Max P 0.25% Max Ferro-Manganese Ferro-Manganese is an alloy with high percentage of Manganese, which is made by heating a mixture of the oxides MnO2 and Fe2O3 and coal & coke with high carbon content in a blast furnace or an electric arc furnace-type system. The oxides go through carbothermal reduction in the furnaces that result in producing the Ferro-Manganese. Ferro-Manganese is used in the production of steel which acts as an excellent deoxidizer and desulfurizer. We supply the one variant of Ferro Manganese: High Carbon Ferro-Manganese.
We supply the Quality Ferro Alloys Like Silico Manganese HC Grade I II Mn 60% min 65% Min Si 14% Min 15% Min / 16% Min C 2.50% Max 2% Max S 0.03% Max 0.03% Max P 0.30% Max 0.30% Max Silicon Manganese Size : 10 - 60 mm Mn; 65 to 70% Si : 16 %c : 2 % P : 0.15 % S : 0.01 % High Carbon Silico Manganese - Standard Grades Mn : 60% Min. / 65% Min. / 70% Min. Si : 15% Min. / 16% Min. / 17% Min. C : 2 % Max. P : 0.30 % Max. S : 0.03 % Max. Size: 10 - 60 mm
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Our range of industrial flanges are ideal for application in diverse industry for high pressure and temperature applications. These flanges are designed with precision for easy installation. Apart from standard flanges, we also offer custom designed flanges to meet the specific application requirements of the customers. 1] Stainless & Duplex Steel Flanges 2] Carbon & Alloy Steel Flanges 3] Nickel & Copper Alloy Flanges 4] Hastelloy Flanges 5] Inconel Flanges 6] Incoloy Flanges 7] Monel Flanges 8] Aluminium Flanges 9] Titanium Flanges
PET Bottles with Aluminium alloy cover or PP cover.
Below is a comprehensive list of our alloys arranged by type. More detailed information can be found on each alloys specific page. All of our products are purchased to normal industry standards and come with material test reports (MTR) also known as material certifications.
Aluminium Alloy Wheel Scrap Enriched with massive industry indulgent and understanding of this sector, we are involved in presenting a wide assortment of Aluminium Alloy wheel scrap. These scraps are widely used for the purposes of reusing and recycling. Available with us in bulk orders, our customers can get these from us at affordable costs. Also, we assure delivering these on time.
Hot selling high quality 99.9% aluminium Scrap Aluminium Wire Scrap Item Quality standard Si 0.2-0.6% Fe 0.35% Cu 0.1% Mn 0.1% Mg 0.45-0.9% Cr 0.1% Zn 0.1% Applications 1. Mainly used for melting ingot 2. Discontinuous melting with scrap 3. Easy control and operation 4. Fast melting 5. Energy saving This Scrap Aluminium is produced in the production of industrial waste. Such as: Scrap Aluminium Wire, Scrap Aluminium block and so on 6. It mainly used for drawing back non-ferrous metal typical material is: Wasted copper, aluminum, cable, aluminum stuff, wasted auto spare part, non-ferrous metal scrap, dross for printing, broken glass contains non-ferroous, electronic waste etc.
Standard ASTM B164 / ASME SB164 Dimensions ASTM, ASME and API Round Bars Size 10 mm To 100 mm Dia in 100 mm TO 6000 mm Length. Round bar Diameter 3-~800mm Hex Bar size 2-100mm A/F Square bar size 4 to 100mm Flat bar Thickness 2 -100mm Flat bar Width 10 to 500mm Length 3 to 6 meter, Custom Cut Lengths Form Round, Square, Hex (A/F), Rectangle, Wire (Coil Form), Wiremesh, Billet, Ingot, Forging Etc.,
Standards ASTM B164, F1554 / ASME SB164, SF1554 Dimensions DIN 931, 933, 934, 7991, 976, 125, ASME B18.2.1, B18.3 Fasteners size Bolt / Screw Size : M3 â?? M56 | 3/6â?³ to 2â?³ | Custom Sizes. Nuts Size : M3 â?? M56 | 3/6â?³ to 2â?³ | Custom Sizes. Washers Size : M3 â?? M56 | 3/6â?³ to 2â?³ | Custom Sizes. Machine Screws Size : M1.6 â?? M12. Self Tapping Screw Size : No.2 â?? No. 14. Length 3 mm to 200 mm Threads UNF, BSW, BSF, METRIC, UNC or as required Surface Coating Ptfe Coated Fasteners Phosphate Coating Teflon Coating Zinc Coating Hot Dipped Galvanizing Coating Cadmium Coating Xylon Coating Finishing Self-Colour, Passivated, Bright Zinc Plated (BZP), Hot Dip Galvanised (HDG), Sherardized, some special one like DACROMET Geometry and Mechanically Applied coating ,Dacroment, nickel plated, anodizing, plated zinc-nickel Zinc (blue, black, yellow, white), black oxide.
