APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
Specifications: Origin: Vietnam Impurities: 1% Usage: Medicine, cosmetics, food processing. Color: Golden, purple Shelf life: 12 months Packing: PP bag and Carton We have 4 types of Golden Cottonii Sea Moss: Type 1: Salted prickly sea moss, 20-30% moisture Type 2: Salted non-prickly sea moss, 20-30% moisture Type 3: Non salted prickly sea moss, 5-7% moisture Type 4: Non salted Non-prickly sea moss, 5-7% moisture
DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
- Product Name: Coco coir pot - Material: 100% natural coconut fiber - Color: Natural golden color - Size: 15 x 10 cm x H 9.5 cm /9 x 6 cm x H 8 cm/6 x 6 cm x H 6 cm /4 x 4 cm x H 4 cm - Type: Floor Bough pot, Flower Kettle/Sprinkler, Flower Tub, POTS, PE - Usage Condition: FLOOR, HOME, Garden, plant engineering, Flower nursery prod - Used With: Flower/Green Plant
Type: Foot Massager Aplication: Office workers, people sitting on computers for a long time, sedentary people, the elderly with osteoarthritis or in the process of treating diseases ... Size: 24cm*24cm*4 Logo: Customized Logo Accept Warranty: 3 years Material: green Sandalwood Accepted Delivery Terms: FOB, CFR, CIF, EXW, CIP, DDP, DDU, Express Delivery Accepted Payment Currency: USD Accepted Payment Type: T/T, L/C, D/P D/A, MoneyGram, PayPal, Western Union, Cash
Type: Tomato Powder (Herbal Extract). Variety : normal or cherry tomato. pH: 4. Acid: 4-4.5%. Salt : 0.8% - 1.0%. Brix : 22-24%, 18-20%, 28-30%. Quantity capacity : 50mts/month. MOQ: 1ton. Preserving in common condition, shelf life: 12 months. Packed in aseptic bag, drums 220kg, 1 x 20ft = 80 bins. Price: please contact for updated price. Payment & delivery: L/C at sight or T/T 30% in advance. Lead time: 2 weeks/ 1*20'FCL.
We are supplier and exporter of All types of ceramic Tiles. We have been exporting Ceramic Tiles to more than 15 countries. We deal in most of the Sizes and Variety of Tiles ie :- 1. 300X450 MM Wall tiles 2. 300X600 MM Wall tiles / Vitrified Tiles 3. 200X600 MM Wall tiles 4. 300X300 MM Wall tiles 5. 250X375 MM Wall Tiles 6 600X600 MM Vitrified Tiles / Double Charge / Full body tiles / Porcelain tiles 7 600X1200 MM Vitrified Tiles /Full body tiles 8 Slab Tiles 9 Subway Tiles 10 Quartz Stone 11 Engineered stone
Origin: Binh Thuan province, Vietnam Preservation process: Freeze Dried. Type: Red and White flesh. Taste: Crispy, sweet. Shelf life: 12 months. Min order: 1,000 kg. Quantity capacity: 30 tons/month. Packaging: Aluminum bag of 50 g NW then in 10 kg carton. 1x20'fcl = 3-4 mt, label as buyerâ??s requirement. Price: please contact for updated price. Payment & delivery: L/C at sight or T/T 30% in advance. Lead time: 3 weeks/ 1*20'FCL.
Tumi Ishi blocks are small chunks of wood, cut kind of like a gemstone. Basically the idea is you are supposed to stack them all up. Tumi ishi Wood Balancing Stones for Baby is a new take on the classic wooden building block. Unlike standard square blocks, these blocks have many sides making them more challenging to stack Type: Block Set, Other Classic Toys Material: Wood Size: 3-6cm Color: Natural color Logo: Customized Logo Age Range: 0 to 24 Months, 2 to 4 Years, 5 to 7 years, 8 to 13 Years,... Usage: Relaxing, Educate, Simulate brain development for kids Packing: Bag/carton
We deals in the following products of India, China, Taiwan and Korea Origin:- 1)Hot Rolled Steel (Hot Rolled Sheets, Hot Rolled Coils, Hot Rolled Plates, Hot Rolled Bars etc) 2)Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc) 3)Cold Rolled Steel (Cold Rolled Steel Strips, Cold Rolled Steel Coils, Cold Rolled Sheets etc) 4)Stainless Steel (Stainless Steel Strips, Stainless Steel Coils, Stainless Steel Wire, Hardened and Tempered Spring Steel, Stainless Spring Steel, Spring Steel Wires etc) 5)Steel Tube and Pipes ( ERW, CRW, CRS, Black, Galvanized, Stainless ) 6)Forged Column Clamps, Girder Clamps, Pressed Clamps, Rapid Clamps, Support Clamps & Wedge Clamps. 7)Heavy Duty Props & Light Duty Props. 8)Nuts, Bolts, Nails & Fastners 9)System Scaffolding, Base Plate & Adjustable Base. 10)Steel Tie Rod, Waller Plates and Wing Nuts. 11)Drop Forged and Pressed Sheet Metal Couplers of all types. 12)Steel Billets, Steel Angle & Steel Channels.
We deals in the following products of India, China, Taiwan and Korea Origin:- 1)Hot Rolled Steel (Hot Rolled Sheets, Hot Rolled Coils, Hot Rolled Plates, Hot Rolled Bars etc) 2)Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc) 3)Cold Rolled Steel (Cold Rolled Steel Strips, Cold Rolled Steel Coils, Cold Rolled Sheets etc) 4)Stainless Steel (Stainless Steel Strips, Stainless Steel Coils, Stainless Steel Wire, Hardened and Tempered Spring Steel, Stainless Spring Steel, Spring Steel Wires etc) 5)Steel Tube and Pipes ( ERW, CRW, CRS, Black, Galvanized, Stainless ) 6)Forged Column Clamps, Girder Clamps, Pressed Clamps, Rapid Clamps, Support Clamps & Wedge Clamps. 7)Heavy Duty Props & Light Duty Props. 8)Nuts, Bolts, Nails & Fastners 9)System Scaffolding, Base Plate & Adjustable Base. 10)Steel Tie Rod, Waller Plates and Wing Nuts. 11)Drop Forged and Pressed Sheet Metal Couplers of all types. 12)Steel Billets, Steel Angle & Steel Channels.
We deals in the following products of India, China, Taiwan and Korea Origin:- 1)Hot Rolled Steel (Hot Rolled Sheets, Hot Rolled Coils, Hot Rolled Plates, Hot Rolled Bars etc) 2)Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc) 3)Cold Rolled Steel (Cold Rolled Steel Strips, Cold Rolled Steel Coils, Cold Rolled Sheets etc) 4)Stainless Steel (Stainless Steel Strips, Stainless Steel Coils, Stainless Steel Wire, Hardened and Tempered Spring Steel, Stainless Spring Steel, Spring Steel Wires etc) 5)Steel Tube and Pipes ( ERW, CRW, CRS, Black, Galvanized, Stainless ) 6)Forged Column Clamps, Girder Clamps, Pressed Clamps, Rapid Clamps, Support Clamps & Wedge Clamps. 7)Heavy Duty Props & Light Duty Props. 8)Nuts, Bolts, Nails & Fastners 9)System Scaffolding, Base Plate & Adjustable Base. 10)Steel Tie Rod, Waller Plates and Wing Nuts. 11)Drop Forged and Pressed Sheet Metal Couplers of all types. 12)Steel Billets, Steel Angle & Steel Channels.
We deals in the following products of India, China, Taiwan and Korea Origin:- 1) Hot Rolled Steel (Hot Rolled Sheets, Hot Rolled Coils, Hot Rolled Plates, Hot Rolled Bars etc.) 2) Galvanized Steel (Galvanized Steel Tapes, Galvanized Steel Wires, Galvanized Steel Strips, Galvanized Steel Coils, Galvanized tubes etc.) 3) Cold Rolled Steel (Cold Rolled Steel Strips, Cold Rolled Steel Coils, Cold Rolled Sheets etc.) 4) Stainless Steel (Stainless Steel Strips, Stainless Steel Coils, Stainless Steel Wire, Hardened and Tempered Spring Steel, Stainless Spring Steel, Spring Steel Wires etc.) 5) Steel Tube and Pipes (ERW, CRW, CRS, Black, Galvanized, Stainless) 6) Forged Column Clamps, Girder Clamps, Pressed Clamps, Rapid Clamps, Support Clamps & Wedge Clamps. 7) Heavy Duty Props & Light Duty Props. 8) Nuts, Bolts, Nails & Fasteners 9) System Scaffolding, Base Plate & Adjustable Base. 10) Steel Tie Rod, Waller Plates and Wing Nuts. 11) Drop Forged and Pressed Sheet Metal Couplers of all types. 12) Steel Billets, Steel Angle & Steel Channels. Price: After receiving complete details