DESCRIPTION ITLS PMS 60 is a single component elastomeric sealant without isocyanates. It cures rapidly under the effect of atmospheric humidity to form a flexible and resistant joint with very good adhesion on most materials. APPLICATION ITLS PMS 60 is suitable for industrial and refrigerated trailers, truck bodies, shipbuilding, air conditioning and ventilation units, sandwich panels and other industrial applications. ITLS PMS 60 can also be used for bonding and caulking different materials used in the building industry : concrete, wood, aluminum, most lacquered metals, polyester, glass, stone, ceramic, and so on. However, for difficult materials especially lacquered or non-ferrous metals, it is necessary to make tests beforehand. INSTRUCTIONS FOR USE SUBSTRATE PREPARATION: The substrates must be clean, even, dry, free of dust, oil, grease and any contaminants that could harm bonding. All traces of poorly adherent paints or coatings should be systematically removed beforehand. They may be cleaned with PMS primer, methylethylketone (MEK) or acetone. Check the compatibility of the solvent used with the substrates. It may be necessary to rub down the substrate beforehand. After rubbing down, the surface should be recleaned. Allow the substrate to dry after degreasing. When using solvents, extinguish all sources of ignition and carefully follow the safety and handling instructions given by the manufacturer. CAULKING: ITLS PMS 60 can be applied by a manual or pneumatic gun. After application, use a putty knife to smooth the joint with soapy water. Do not apply at a temperature under 5 C. In cold weather, store the cartridges at about 20 �°C before use. This product should be used within 24 hours of opening the cartridge protection; otherwise, the sealant could harden inside. Avoid any contact with non-cured polyurethanes during curing. CLEANING: Tools can be cleaned with PMS primer, MEK or acetone before the sealant has completely cured. After curing, abrasion is necessary. STORAGE AND SHELF LIFE 12 months in the original, hermetically sealed packagings between 5 and 25 C PACKAGING 290 mL cartridges and 600 ml sausages SAFETY Not classified as hazardous. Read the material safety data sheet before use.
Using Wellyoung Easy Clean Panel, you can renew your room in 3 hours. It cuts easy and with it being peel and stick, there's no grout and no mess. Features WELLYOUNG EASY CLEAN PANEL Quickly Installed Without Any Mess or Specialized Tools Lightweight, easy to handle, to cut and to clean Especially Designed for Kitchen and Bathroom Resistant to heat of stovetops and humidity of bathrooms Guaranteed to Stick to Your Walls No extra glue, will never yellow or crack over time Installation 1 Clean your wall First, wash the surface with a powerful grease-remover such as TSP (Tri-Sodium Phosphate). Make sure you allow enough time for the surface to dry properly. 2 Trace your guidelines Using a level or chalk line, trace a guideline to ensure perfect alignment using a Mosaïk to mark the height. If you are facing an uneven counter, mark the height of your guideline on the lowest side of the counter. 3 Measure & Cut Measure with a ruler and report it on the tile. Using a box cutter and a metal ruler with a cork backing will let you easily cut a hole or other shapes within the tiles more accurately. 4 Peel & Stick Simply fold back half of the protective paper in the back without touching the adhesive portion with your fingers. Now align the adhesive portion with your guideline and apply a light pressure. Applications Residential Area Commercial Area Bathroom / shower room Toliet Bedroom Corridor Kitchen Hotel Sofa / TV background Shopping Center Size: 305x610mm thickness: 6.5mm Colors:multi colors
Product Details Using Wellyoung Easy Clean Panel, you can renew your room in 3 hours. It cuts easy and with it being peel and stick, there's no grout and no mess. Features WELLYOUNG EASY CLEAN PANEL Quickly Installed Without Any Mess or Specialized Tools Lightweight, easy to handle, to cut and to clean Especially Designed for Kitchen and Bathroom Resistant to heat of stovetops and humidity of bathrooms Guaranteed to Stick to Your Walls No extra glue, will never yellow or crack over time Installation 1 Clean your wall First, wash the surface with a powerful grease-remover such as TSP (Tri-Sodium Phosphate). Make sure you allow enough time for the surface to dry properly. 2 Trace your guidelines Using a level or chalk line, trace a guideline to ensure perfect alignment using a Mosaïk to mark the height. If you are facing an uneven counter, mark the height of your guideline on the lowest side of the counter. 3 Measure & Cut Measure with a ruler and report it on the tile. Using a box cutter and a metal ruler with a cork backing will let you easily cut a hole or other shapes within the tiles more accurately. 4 Peel & Stick Simply fold back half of the protective paper in the back without touching the adhesive portion with your fingers. Now align the adhesive portion with your guideline and apply a light pressure. Size: 305x610x5.5mm 185x915x5.5mm
Using Wellyoung Easy Clean Panel, you can renew your room in 3 hours. It cuts easy and with it being peel and stick, there's no grout and no mess. Structure 1. High resistance PU overlay protector 2. High definition PVC laminate 3. Mgo board 4. Self-adhesive EVA foam with space to apply silicone Features Quickly Installed Without Any Mess or Specialized Tools Lightweight, easy to handle, to cut and to clean Especially Designed for Kitchen and Bathroom Resistant to heat of stovetops and humidity of bathrooms Guaranteed to Stick to Your Walls No extra glue, will never yellow or crack over time Installation 1 Clean your wall First, wash the surface with a powerful grease-remover such as TSP (Tri-Sodium Phosphate). Make sure you allow enough time for the surface to dry properly. 2 Trace your guidelines Using a level or chalk line, trace a guideline to ensure perfect alignment using a Mosaïk to mark the height. If you are facing an uneven counter, mark the height of your guideline on the lowest side of the counter. 3 Measure & Cut Measure with a ruler and report it on the tile. Using a box cutter and a metal ruler with a cork backing will let you easily cut a hole or other shapes within the tiles more accurately. 4 Peel & Stick Simply fold back half of the protective paper in the back without touching the adhesive portion with your fingers. Now align the adhesive portion with your guideline and apply a light pressure. Size 305x610x5.5mm packing: 10pcs/box,90boxes/pallet,20pallets/20GP'
Using Wellyoung Easy Clean Panel, you can renew your room in 3 hours. It cuts easy and with it being peel and stick, there's no grout and no mess. Features WELLYOUNG EASY CLEAN PANEL Quickly Installed Without Any Mess or Specialized Tools Lightweight, easy to handle, to cut and to clean Especially Designed for Kitchen and Bathroom Resistant to heat of stovetops and humidity of bathrooms Guaranteed to Stick to Your Walls No extra glue, will never yellow or crack over time Installation 1 Clean your wall First, wash the surface with a powerful grease-remover such as TSP (Tri-Sodium Phosphate). Make sure you allow enough time for the surface to dry properly. 2 Trace your guidelines Using a level or chalk line, trace a guideline to ensure perfect alignment using a Mosaïk to mark the height. If you are facing an uneven counter, mark the height of your guideline on the lowest side of the counter. 3 Measure & Cut Measure with a ruler and report it on the tile. Using a box cutter and a metal ruler with a cork backing will let you easily cut a hole or other shapes within the tiles more accurately. 4 Peel & Stick Simply fold back half of the protective paper in the back without touching the adhesive portion with your fingers. Now align the adhesive portion with your guideline and apply a light pressure. Applications Residential Area Commercial Area Bathroom / shower room Toliet Bedroom Corridor Kitchen Hotel Sofa / TV background Shopping Center
Using Wellyoung Easy Clean Panel, you can renew your room in 3 hours. It cuts easy and with it being peel and stick, there's no grout and no mess. Features WELLYOUNG EASY CLEAN PANEL Quickly Installed Without Any Mess or Specialized Tools Lightweight, easy to handle, to cut and to clean Especially Designed for Kitchen and Bathroom Resistant to heat of stovetops and humidity of bathrooms Guaranteed to Stick to Your Walls No extra glue, will never yellow or crack over time Installation 1 Clean your wall First, wash the surface with a powerful grease-remover such as TSP (Tri-Sodium Phosphate). Make sure you allow enough time for the surface to dry properly. 2 Trace your guidelines Using a level or chalk line, trace a guideline to ensure perfect alignment using a Mosaïk to mark the height. If you are facing an uneven counter, mark the height of your guideline on the lowest side of the counter. 3 Measure & Cut Measure with a ruler and report it on the tile. Using a box cutter and a metal ruler with a cork backing will let you easily cut a hole or other shapes within the tiles more accurately. 4 Peel & Stick Simply fold back half of the protective paper in the back without touching the adhesive portion with your fingers. Now align the adhesive portion with your guideline and apply a light pressure. Applications Residential Area Commercial Area Bathroom / shower room Toliet Bedroom Corridor Kitchen Hotel Sofa / TV background Shopping Center
SF-1D hydraulic bushingIt is the substitute of and parallels in performance with abroad DP4.It has been designed to special working condition of reciprocating motion and meanwhile considering the motion way of oil pump and damper. SF-1D in particular fits frequently reciprocating motion with a high side force. The upgrade products will cover a wide application in automobile,, motor damper and oil pumps, etc.Product Technical Data:Load capacity�140N/mm2 Temperature�-195~+280°C Speedlimit�3m/s;; Friction;coef(μ)�0.04~0.20 PV;limit�dry��3.8N/;mm2.m/s PV;limit�oil��50N/;mm2.m/sProduct Feature And Application· Good wear and low friction performance over a wide ; range of loads, speeds and temperatures in dry running ; conditions· Very good performance in lubricated applications· Good performance in greased applications· Suitable for ; linear, oscillating and rotating movements· Lead-free ; material compliant to RoHS specifications. Automotive : Braking systems, clutches, gearbox and transmissions, hinges : door, bonnet, boot, cabriolet ; roof tops,pedals, pumps : axialpiston, radial piston, gear and ; vane, seat mechanisms, steering systems, struts and shock ; absorbers wiper systems, etc.Industrial : Aerospace, agricultural equipment, construction equipment, food and beverage, material handling equipment,forming machines :metal, plastic and rubber, office ; equipment,medical and scientific equipment, packaging equipment,pneumatic and hydraulic cylinders, pumps and motors, ; railroadand tramways, textile machinery, valves, etc.Product Etailsmicrosection  ---PTFE with Oil Fibre, 0.01~0.03mm---Porous bronze, 0.2~0.3mm   (CuSn8Zn3:Sn
SF-1D hydraulic bushingIt is the substitute of and parallels in performance with abroad DP4.It has been designed to special working condition of reciprocating motion and meanwhile considering the motion way of oil pump and damper. SF-1D in particular fits frequently reciprocating motion with a high side force. The upgrade products will cover a wide application in automobile,motor damper and oil pumps, etc.Product Technical Data:Load capacity�140N/mm2 Temperature�-195~+280°C Speedlimit�3m/s;; Friction;coef(μ)�0.04~0.20 PV;limit�dry��3.8N/;mm2.m/s PV;limit�oil��50N/;mm2.m/sProduct Feature And Application· Good wear and low friction performance over a wide ; range of loads, speeds and temperatures in dry running ; conditions· Very good performance in lubricated applications· Good performance in greased applications· Suitable for ; linear, oscillating and rotating movements· Lead-free ; material compliant to RoHS specifications. Automotive : Braking systems, clutches, gearbox and transmissions, hinges : door, bonnet, boot, cabriolet ; roof tops,pedals, pumps : axialpiston, radial piston, gear and ; vane, seat mechanisms, steering systems, struts and shock ; absorbers wiper systems, etc.Industrial : Aerospace, agricultural equipment, construction equipment, food and beverage, material handling equipment,forming machines :metal, plastic and rubber, office ; equipment,medical and scientific equipment, packaging equipment,pneumatic and hydraulic cylinders, pumps and motors, ; railroadand tramways, textile machinery, valves, etc.Product Etailsmicrosection  ---PTFE with Oil Fibre, 0.01~0.03mm---Porous bronze, 0.2~0.3mm   (CuSn8Zn3:Sn
SF-1D hydraulic bushingIt is the substitute of and parallels in performance with abroad DP4.It has been designed to special working condition of reciprocating motion and meanwhile considering the motion way of oil pump and damper. SF-1D in particular fits frequently reciprocating motion with a high side force. The upgrade products will cover a wide application in automobile,com, motor damper and oil pumps, etc.Product Technical Data:Load capacity�140N/mm2 Temperature�-195~+280°C Speedlimit�3m/s;; Friction;coef(μ)�0.04~0.20 PV;limit�dry��3.8N/;mm2.m/s PV;limit�oil��50N/;mm2.m/sProduct Feature And Application· Good wear and low friction performance over a wide ; range of loads, speeds and temperatures in dry running ; conditions· Very good performance in lubricated applications· Good performance in greased applications· Suitable for ; linear, oscillating and rotating movements· Lead-free ; material compliant to RoHS specifications. Automotive : Braking systems, clutches, gearbox and transmissions, hinges : door, bonnet, boot, cabriolet ; roof tops,pedals, pumps : axialpiston, radial piston, gear and ; vane, seat mechanisms, steering systems, struts and shock ; absorbers wiper systems, etc.Industrial : Aerospace, agricultural equipment, construction equipment, food and beverage, material handling equipment,forming machines :metal, plastic and rubber, office ; equipment,medical and scientific equipment, packaging equipment,pneumatic and hydraulic cylinders, pumps and motors, ; railroadand tramways, textile machinery, valves, etc.Product Etailsmicrosection  ---PTFE with Oil Fibre, 0.01~0.03mm---Porous bronze, 0.2~0.3mm   (CuSn8Zn3:Sn
SF-1D hydraulic bushingIt is the substitute of and parallels in performance with abroad DP4.It has been designed to special working condition of reciprocating motion and meanwhile considering the motion way of oil pump and damper. SF-1D in particular fits frequently reciprocating motion with a high side force. The upgrade products will cover a wide application in automobile,motor damper and oil pumps, etc.Product Technical Data:Load capacity�140N/mm2 Temperature�-195~+280°C Speedlimit�3m/s;; Friction;coef(μ)�0.04~0.20 PV;limit�dry��3.8N/;mm2.m/s PV;limit�oil��50N/;mm2.m/sProduct Feature And Application· Good wear and low friction performance over a wide ; range of loads, speeds and temperatures in dry running ; conditions· Very good performance in lubricated applications· Good performance in greased applications· Suitable for ; linear, oscillating and rotating movements· Lead-free ; material compliant to RoHS specifications. Automotive : Braking systems, clutches, gearbox and transmissions, hinges : door, bonnet, boot, cabriolet ; roof tops,pedals, pumps : axialpiston, radial piston, gear and ; vane, seat mechanisms, steering systems, struts and shock ; absorbers wiper systems, etc.Industrial : Aerospace, agricultural equipment, construction equipment, food and beverage, material handling equipment,forming machines :metal, plastic and rubber, office ; equipment,medical and scientific equipment, packaging equipment,pneumatic and hydraulic cylinders, pumps and motors, ; railroadand tramways, textile machinery, valves, etc.Product Etailsmicrosection  ---PTFE with Oil Fibre, 0.01~0.03mm---Porous bronze, 0.2~0.3mm   (CuSn8Zn3:Sn
SF-1D hydraulic bushingIt is the substitute of and parallels in performance with abroad DP4.It has been designed to special working condition of reciprocating motion and meanwhile considering the motion way of oil pump and damper. SF-1D in particular fits frequently reciprocating motion with a high side force. The upgrade products will cover a wide application in automobile, motor damper and oil pumps, etc.Product Technical Data:Load capacity�140N/mm2 Temperature�-195~+280°C Speedlimit�3m/s;; Friction;coef(μ)�0.04~0.20 PV;limit�dry��3.8N/;mm2.m/s PV;limit�oil��50N/;mm2.m/sProduct Feature And Application· Good wear and low friction performance over a wide ; range of loads, speeds and temperatures in dry running ; conditions· Very good performance in lubricated applications· Good performance in greased applications· Suitable for ; linear, oscillating and rotating movements· Lead-free ; material compliant to RoHS specifications. Automotive : Braking systems, clutches, gearbox and transmissions, hinges : door, bonnet, boot, cabriolet ; roof tops,pedals, pumps : axialpiston, radial piston, gear and ; vane, seat mechanisms, steering systems, struts and shock ; absorbers wiper systems, etc.Industrial : Aerospace, agricultural equipment, construction equipment, food and beverage, material handling equipment,forming machines :metal, plastic and rubber, office ; equipment,medical and scientific equipment, packaging equipment,pneumatic and hydraulic cylinders, pumps and motors, ; railroadand tramways, textile machinery, valves, etc.Product Etailsmicrosection  ---PTFE with Oil Fibre, 0.01~0.03mm---Porous bronze, 0.2~0.3mm   (CuSn8Zn3:Sn
SF-1D hydraulic bushingIt is the substitute of and parallels in performance with abroad DP4.It has been designed to special working condition of reciprocating motion and meanwhile considering the motion way of oil pump and damper. SF-1D in particular fits frequently reciprocating motion with a high side force. The upgrade products will cover a wide application in automobile,Website:http://www.oillessbearing1.com, motor damper and oil pumps, etc.Product Technical Data:Load capacity�140N/mm2 Temperature�-195~+280°C Speedlimit�3m/s;; Friction;coef(μ)�0.04~0.20 PV;limit�dry��3.8N/;mm2.m/s PV;limit�oil��50N/;mm2.m/sProduct Feature And Application· Good wear and low friction performance over a wide ; range of loads, speeds and temperatures in dry running ; conditions· Very good performance in lubricated applications· Good performance in greased applications· Suitable for ; linear, oscillating and rotating movements· Lead-free ; material compliant to RoHS specifications. Automotive : Braking systems, clutches, gearbox and transmissions, hinges : door, bonnet, boot, cabriolet ; roof tops,pedals, pumps : axialpiston, radial piston, gear and ; vane, seat mechanisms, steering systems, struts and shock ; absorbers wiper systems, etc.Industrial : Aerospace, agricultural equipment, construction equipment, food and beverage, material handling equipment,forming machines :metal, plastic and rubber, office ; equipment,medical and scientific equipment, packaging equipment,pneumatic and hydraulic cylinders, pumps and motors, ; railroadand tramways, textile machinery, valves, etc.Product Etailsmicrosection  ---PTFE with Oil Fibre, 0.01~0.03mm---Porous bronze, 0.2~0.3mm   (CuSn8Zn3:Sn
SF-1D hydraulic bushingIt is the substitute of and parallels in performance with abroad DP4.It has been designed to special working condition of reciprocating motion and meanwhile considering the motion way of oil pump and damper. SF-1D in particular fits frequently reciprocating motion with a high side force. The upgrade products will cover a wide application in automobile,motor damper and oil pumps, etc.Product Technical Data:Load capacity�140N/mm2 Temperature�-195~+280°C Speedlimit�3m/s;; Friction;coef(μ)�0.04~0.20 PV;limit�dry��3.8N/;mm2.m/s PV;limit�oil��50N/;mm2.m/sProduct Feature And Application· Good wear and low friction performance over a wide ; range of loads, speeds and temperatures in dry running ; conditions· Very good performance in lubricated applications· Good performance in greased applications· Suitable for ; linear, oscillating and rotating movements· Lead-free ; material compliant to RoHS specifications. Automotive : Braking systems, clutches, gearbox and transmissions, hinges : door, bonnet, boot, cabriolet ; roof tops,pedals, pumps : axialpiston, radial piston, gear and ; vane, seat mechanisms, steering systems, struts and shock ; absorbers wiper systems, etc.Industrial : Aerospace, agricultural equipment, construction equipment, food and beverage, material handling equipment,forming machines :metal, plastic and rubber, office ; equipment,medical and scientific equipment, packaging equipment,pneumatic and hydraulic cylinders, pumps and motors, ; railroadand tramways, textile machinery, valves, etc.Product Etailsmicrosection  ---PTFE with Oil Fibre, 0.01~0.03mm---Porous bronze, 0.2~0.3mm   (CuSn8Zn3:Sn
Plastic injection auto mirrors shell/cover/house1.High quality plastic molding all kinds of plastic  &mold products2.Best  favourable price 3.Mass plastic parts production  Specification Sheet:NoMold description:china high quality plastic  parts  injection mould 1Material type:1.23442Cavity no.:Single or Multi Cavities or Customized3Cav&Cor Material: S136,Website:http://www.oemplasticmold.com,SKD61,H13,718,P20 etc4Hardness of Cav&Cor:HRC48-53°5Mould Base:LKM&Hasco&DME standard 6Surface finish:SPI A-1,SPI A-2,EDM etc7Mold components:Mold base,core and cavity8Mold Gate:Hot runner,direct sprue gate,side gate,pin-piont Gate etc9Runner system:Hot runner10Mould Life:50000-3000K shots11Product material:PA,PA6/6+GF,ABS,POM,PC,PP,PET,TPE,PVC,HDPE,PEEK,PPSU,PAI,PEI,PPO etc12Suitable for:Plastic injection moulding Parts13Design software:CAD,UG,Pro E,Solidworks14PackageWooden or Plywood Case 15Delivery4-7 Weeks depends on different products16Value-added service:Polish, texture, painting, screen printing,  assembly17Export country:Europe Countries, USA, Mexico, Australia ,Middle-east ,Asia etc Packaging & DeliveryPackaging DetailsFor mold: After the mold assembled and cleared , anti-rust fog or grease painted onto mold, then covered with thin film and placed into a stable wooden box. For plastic product: the first thing is to wrap each part up with semi-transparent thin foam and put it into plastic bag, the second step is to place them into cartons with thin sponge plates to prevent scratches. Or as per requirements.Delivery Time20-45 working days it depends on your requirements
1. Scope of Application: Used for one-time protection during the surgery conducted by the department of a medical therapy unit. 2. Supports customization according to the customer's drawings and requirements. Fitting Name Size Quantity Material Hand towel 30cm*40cm 2 45g Spunlace Reinforced Surgical Gown L(125*145) 2 SMS+ Laminating nonwoven fabrics Op-tape 10cm*50cm 2 SMS Utility drape with tape 50cm*60cm 4 SMS Craniototomy Drape 310cm*340cm*188cm 1 SMS Reinforced Mayo Stand Cover 75cm*145cm 1 PP+PE Back Table Cover 145cm*190cm 1 PSB+PE Double Layer Drape 60cm*65cm 2 SMS (1) Surgical Gown: Features high protectiveness, which can prevent the penetration of blood, grease, and alcohol. (2) Medium Drape: Effectively blocks liquid and bacterial penetration and prevents cross infection when covering the patient. (3) Ulitity Drape: Absorbs liquid and can be replaced in time. (4) Craniotomy Drape: Reveals the surgical field of view and effectively blocks liquid and bacteria when covering an aseptic surgical area. (5) Reinforced Mayo Stand Cover: Reveals the surgical field of view and effectively blocks liquid and bacteria when covering an aseptic surgical area. (6) Back Table Drape: Parcels the accessories in an operating instrument set, or functions as a table cloth on which the apparatus is arranged when taken out from an operating instrument set. (7) Double Layer Drape: Reveals the surgical field of view and effectively blocks liquid and bacteria.
1. Scope of Application: Used for one-time protection during the surgery conducted by the department of a medical therapy unit. 2. Supports customization according to the customer's drawings and requirements. Fitting Name Size Quantity Material Surgical Gown L(125*145) 2 SMS Utility Drape with Tape 50cm*60cm 4 SMS Thyroid Drape 200cm*320cm 1 SMS+Absorbent material Reinforced Mayo Stand Cover 75cm*145cm 1 PP+PE Medium Drape 120cm*100cm 1 SMS Back Table Cover 145cm*190cm 1 PSB+PE Double Layer Drape 60cm*65cm 1 SMS (1) Surgical Gown: Features high protectiveness, which can prevent the penetration of blood, grease, and alcohol. (2) Ulitity Drape: Absorbs liquid and can be replaced in time. (3) Thyroid Drape: Reveals the surgical field of view and effectively blocks liquid and bacteria when covering an aseptic surgical area. (4) Reinforced Mayo Stand Cover: Reveals the surgical field of view and effectively blocks liquid and bacteria when covering an aseptic surgical area. (5) Medium Drape: Effectively blocks liquid and bacterial penetration and prevents cross infection when covering the patient. (6) Back Table Drape: Parcels the accessories in an operating instrument set, or functions as a table cloth on which the apparatus is arranged when taken out from an operating instrument set. (7) Gauze Ball: Stop bleeding, press and absorb fluid during surgery. (8) Double Layer Drape: Effectively blocks liquid and bacterial penetration and prevents cross infection.
Floor scrubber robot-w1 features: 1.Clean and dry going either forward or backwards. 2. It is perfect choice for heavy-duty cleaning such as entryways, spill cleanup, grease removal, grout and porous-surface cleaning etc. 3. User-friendly, the one-touch control panel is compactly designed while the more effective performance. All switches are indicated by chart, easy operate and high productivity. 4. Flexible only 100cm turn-around aisle width ensures the machine to suit for more environments. 5. Easily assembled and maintained with lowest running cost, excellent performance gives the safe and smooth operation to the user. 6. Large-capacity battery enables it to work continuously for long time. Dimensions(l*w*h) 1700*960*1200mm Max. Speed 1.3m/s Cleaning efficiency 4500m2/h Volume of solution tank 240l Volume of recovery tank 300l Continuous working hours without adding water 6h(max.) Battery voltage 24v Charging method Charging manually (automatic charging is optional) Fast replacement of battery Achievable Continuous working hours without recharging >4h Max. Cleaning floor area 27000m2 Applicable environment Indoor Service conditions 0~50âºc Safety measures Quadruple safety sensors, accurate to a single millimeter Obstacle avoidance strategy Stop moving/ bypass
DESCRIPTION a premium cement based finish skimcoat which contains selected filler, additive and polymer used for smooth finishing to uneven concrete wall & ceiling. After dry STARCOAT CN have a excellent adhesion to the substrate, better impact resistant, no powdery, no cracks, smooth and ready to be painted with water based wall paint. Easy to use, good workability and have a long pot life and correction time even at the outdoor applications. USES IN APPLICATIONS 1. Cement Based Wall Plaster. 2. Concrete Wall, Column & Ceiling 3. Precast Concrete & Concrete profile 4. Internal & External. ADVANTAGE * Light, good workability and sanding properties. * No cracks and hair cracks. (depends on background) * Smooth surface, solid and no powdery. * Can be painted or finished with wallpaper directly after dry in minimum 24 hours * without using PVA putty to leveling up & filling uneven rough surface. PRODUCT SPESIFICATIONS 1. Main Binder : Portland Cement & Polymer 2. Filler : Limestone 3. Color : GREY and WHITE. 4. Mixing Ratio : 7 - 8 litres of water per 25 Kg bags. or 28 - 32 % water demands. 5. Coverage : 1.25-1.3 Kg/m2/mm or 19m2/25 Kg/mm thickness average 7.5m2/25Kg for 2-3mm thickness 6. Thickness : 2mm thickness/coat 4mm for 2 coats and 6mm for 3 coats. 7. Pot Life : approx. 60 minutes SURFACE PREPARATION * The substrate must be clean and free from grease and loose particles. Recesses should be pre-patched and levelled where appropriate. * Porous and absorbent substrates must be pre-wetted prior to application of Starcoat CN finish coat.
DESCRIPTION STARCOAT PL, is fine grade cement based finish plastering skimcoat which contains selected filler and additive used for smooth finishing to uneven wall cement based plaster and ceiling. After dry STARCOAT PL have a good adhesion to the substrate, no cracks, smooth, no dust on the surface and ready to be painted with water based paint. Easy to use, good workability and have a long pot life and correction time even at the outdoor applications. USES IN APPLICATIONS *Cement Based Wall Plaster. *Precast Concrete. *Concrete Profile & Concrete Ceilings *Internal & External. ADVANTAGE *Light, good workability and sanding properties. *No cracks and hair cracks. (depends on background) *Smooth surface, solid and no powdery. *Can be painted or finished with wallpaper directly after dry in minimum 24 hours without using PVA putty to leveling up & filling uneven rough surface. PRODUCT SPESIFICATIONS 1. Main Binder : Portland Cement & Polymer 2. Filler: Limestone 3. Color: GREY and WHITE. 4. Mixing Ratio : 7 - 8 litres of water per 25 Kg bags. or 28 - 32 % water demands. 5. Coverage: 1.25-1.3 Kg/m2/mm or 19m2/25 Kg/mm thickness average 7.5m2/25Kg for 2-3mm thickness 6. Thickness: 2mm thickness/coat 4mm for 2 coats and 6mm for 3 coats. 7. Pot Life: approx. 60 minutes SURFACE PREPARATION 1. The substrate must be clean and free from grease and loose particles. Recesses should be pre-patched and levelled where appropriate. 2. Porous and absorbent substrates must be pre-wetted prior to application of Starcoat PL finish coat.
Being a well-distinguished company in the market, we are into offering Virgin Base Oil SN 500. Base oils are used to manufacture products including lubricating greases, motor oil and metal processing fluids. Different products require different compositions and properties in the oil. One of the most important factors is the liquid's viscosity at various temperatures. Whether or not a crude oil is suitable to be made into a base oil is determined by the concentration of base oil molecules as well as how easily these can be extracted. Base oil is produced by means of refining crude oil. This means that the crude oil is heated in order that various distillates can be separated from one another. During the heating process, light and heavy hydrocarbons are separated - the light ones can be refined to make petrol and other fuels, while the heavier ones are suitable for bitumen and base oils.[1] There are large numbers of crude oils all around the world that are used to produce base oils. The most common one is a type of paraffinic crude oil, although there are also naphthenic crude oils that create products with better solubility and very good properties at low temperatures. By using hydrogenation technology, in which sulfur and aromatics are removed using hydrogen under high pressure, you can obtain extremely pure base oils, which are suitable when quality requirements are particularly stringent.[2] Chemical substances - additives - are added to the base oil in order to meet the quality requirements for the end products in terms of, for example, friction and cleaning properties. Certain types of motor oils contain more than twenty percent additives
