Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Type 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data :- COLOUR : Red FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Type 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Description Two-component air-drying polyurethane based primer containing zinc phosphate as anti corrosive pigment. Recommended Use :- It is recommended as a primer for MS surface in OEM applications as well as in Process industries like fertilizer plants, Refineries, Petrochemical industries for protection of steel pipelines and structural from corrosion. Physical Data COLOUR : Grey FINISH : Matt SOLIDS BY VOLUME : 40 �± 3% THEORETICAL SPREADING RATE : 13.33 sq.mt / lit at recommended DFT of 30 �µ FLASH POINT : Base : Above 23�° C Hardener : Above 30�° C DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be manually cleaned with brass wire brush, coarse emery paper, scraper, etc to remove rust, dust, loose old coating, oil, grease, and other foreign contaminants. It is preferable to give a solvent wipe after surface preparation. The surface should be absolutely dry, moisture and oil free before primer application or Phosphated components by 7-tank pretreatment process of surface preparation. Application Data MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray THINNER : Thinner 290 POT LIFE : 3 hours min at 30�° C RECOMMENDED DFT : 30-40 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX :24 hours (if it exceeds, the surface should be roughened by emery scuffing grade 320) COMPATIBILITY : Can be top coated with Epoxy, Polyurethane, Chlorinated rubber and Alkyd finish coatings.
Description Two component Epoxy based anti corrosive primer containing zinc phosphate as corrosion inhibiting pigments Recommended Use :- It is an ideal primer where faster turnaround of equipment is desired, Hence making it ideal primer for industrial and Infrastructure equipments, heavy machineries etc exposed to medium corrosive and marine environment. It is also recommended for steel structures in Chemical, Fertilizers, Petrochemical and industrial plants. Not to be used for immersion application. Physical Data :- COLOUR : Grey, Yellow, Beige, Red oxide FINISH : Egg Shell SOLIDS BY VOLUME : 48 ± 3% (Depends on shade) THEORETICAL SPREADING RATE : sq.mt / lit at recommended DFT of 30 µ FLASH POINT : Base : Above 23C Hardener : Above 23C DRYING CHARACTERISTICS (At 65% Relative Humidity & at 30C) : DRY TO HANDLE: 3 hr's max FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to Sa 21/2 Swedish Standards is the best method of surface preparation. In case blasting is not possible, then the surface of steel should be cleaned to St-2/St-3 std. The surface should be absolutely dry, moisture and oil free before primer application. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray THINNER : Epoxy Thinner 190 POT LIFE : 4 hours min at 30C RECOMMENDED DFT : 30 - 40 µ. OVERCOATING INTERVAL : MIN : 2 hours MAX : 24 hours COMPATIBILITY : Can be over coated with Epoxy, PU, Chlorinated rubber and Oleo-resinous Top coats.
Description Two Component, Air-drying, Epoxy Polyamide Cured Finish Paint. Recommended Use :- It Is Recommended As A Top Coat For Structures, Pipelines, Vessels, Equipments And Machineries, Storage Tanks Etc. In Fertilizers And Chemical Plant, Cement Plants, Power Plants, Steel Plants, Pharmaceutical And Petrochemical Complexes, Refineries Etc. Product Is Also Recommended For Application Over Suitable Primer For Oem Industry Like Machine Tools, Pumps, Machineries, Transformers Etc. Physical Data Colour : assorted Shades Finish : glossy / Semi Glossy Solids By Volume : 40 +3% (depends On Shade) Theoretical Spreading Rate : 13.33 Sq.mt / Ltr At Recommended Dft Of 30 au Flash Point : base: Above 23 C Hardener: Above 23 C Drying Characteristics (at 30'c And 65% Relative Humidity) : hard Dry : Overnight Full Cure : 7 Days Shelf Life : base : 6 Months Hardener : 6 Months Surface Preparation This Being A Topcoat, Which Is Applied Over, Primer Or Intermediate Coats, The Surface Should Be Free From Oil, Moisture, Dust And Dirt. Aged Epoxy / Pu Coating Should Be Roughened By Emery Paper Grade 400 / 600 For Better Bonding. Application Data :- Mixing Ratio : base : Hardener (as Per Our Recommendation) Application : by Brush / By Conventional Spray / By Airless Spray Thinner : 190 Pot Life : 4-6hrs Min At 30 C Recommended Dft : 30-40 U Over Coating Interval : min : 8 Hours Max : 24 Hours Compatibility : can Be Over Coated With Pu, Chlorinated Rubber And Synthetic Enamel Paints.
Description Two component, air-drying, Epoxy polyamide cured finish paint. Recommended Use :- It is recommended as a top coat for structures, pipelines, vessels, equipments and machineries, storage tanks etc. in fertilizers and chemical plant, cement plants, power plants, steel plants, pharmaceutical and petrochemical complexes, refineries etc. Product is also recommended for application over suitable primer for OEM industry like machine tools, pumps, machineries, transformers etc. Physical Data COLOUR : Assorted Shades FINISH : Semi glossy SOLIDS BY VOLUME : 40 �± 3% (Depends on shade) THEORETICAL SPREADING RATE : 13.33 sq.mt / ltr at recommended DFT of 30 �µ FLASH POINT : Base: Above 23�° C Hardener: Above 23�° C DRYING CHARACTERISTICS : SURFACE DRY : 90 minutes max HARD DRY : Overnight FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendation) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : 190 POT LIFE : 4-6hrs min at 30 �° C RECOMMENDED DFT : 30-40 �µ OVER COATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be over coated with PU, Chlorinated rubber and synthetic enamel paints.
Description Two-component air-drying intermediate/primer surfacer coat. Recommended Use :- Recommended over putty / primer applied surfaces for better gloss retention and aesthetics in topcoats. Physical Data :- COLOUR : Grey, White FINISH : Egg Shell to Matt SOLIDS BY VOLUME : 40 �± 3% SPREADING RATE : 13.3 sq.mt / ltr at recommended DFT of 30 �µ FLASH POINT : Base : 23�°C Hardener : 23�°C DRYING CHARACTERISTICS (At 30�°C & 65% Relative Humidity) : SURFACE DRY : 20-30 minutes. HARD DRY : Overnight. FULL CURE : 7 Days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation This being intermediate, it is applied either over primer. The surface should be free from moisture, oil and dust before application. In case of aged epoxy / PU coating or exceeded over coating, the surface should be sufficiently roughened prior to painting. Application Data :- MIXING RATIO : Base: Hardener ( As per our recommendation) APPLICATION : By Brush/ By Conventional Spray / By Airless Spray THINNER : Type 290 POT LIFE : 4 hours min at 30�° C RECOMMENDED DFT : 30 -35 �µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours COMPATIBILITY : Can be top coated by PU, epoxy, Chlorinated rubber and synthetic enamel paints. Compatible with Epoxy and zinc rich primers.
Description Two component metallic zinc rich epoxy high performance primer. Recommended Use :- The zinc pigment in dry film renders excellent protection to steel structure, tanks, bullets, dam gates, pipelines, plant equipments, jetty, etc. in both interior and exterior exposed conditions of fertilizer units, chemical plants, steel plants, cement plants, pulp and paper industries, ports, power plants, petrochemical and pharmaceutical industry, transformer, machines & other heavy duty OEMs. It also provides cathodic protection to steel and gives good resistance to corrosion at local damaged areas. It is useful in heavy-duty protective paint systems. It is recommended not to expose the primed coat alone to chemical and saline atmosphere for a long time. Physical Data COLOUR : Grey FINISH : Matt SOLIDS BY VOLUME : 50 �± 3% THEORETICAL SPREADING RATE : 10 sq.mt / ltr at DFT of 50 �µ FLASH POINT : Base : Above 23�°C Hardener : Above 23�°C DRYING CHARACTERISTICS (at 30�°C & at 65% Relative Humidity) : HARD DRY : Overnight FULL CURE : 7 days SHELF LIFE : BASE : 6 months HARDENER : 6 months Surface Preparation Abrasive blasting to minimum Sa 2 1/2 Standards is recommended with a profile of 35 - 75 microns. The surface should be absolutely dry and salt free before application. The primer should be applied preferably immediately or within 4 hours of blasting. Application Data :- MIXING RATIO : Base : Hardener (As per our recommendations) APPLICATION : By Brush / By Conventional Spray / By Airless Spray THINNER : Epoxy Thinner 190 POT LIFE : 4 hours min at 30�°C RECOMMENDED DFT : 30 50 µ. OVERCOATING INTERVAL : MIN : 8 hours MAX : Infinite COMPATIBILITY : Compatible with Epoxy, PU, Chlorinated Rubber intermediate/finish coat.
Nickel mesh anode is an anode material crafted from nickel. It is formed through a meticulous precision expanding technique using nickel sheet. Its exceptional corrosion resistance,� reliable electrical conductivity, and impressive durability guarantee a long-lasting service life. Nickel mesh anodes possess notable benefits such as superior� current efficiency, cost-effectiveness, and exceptional corrosion resistance. They are versatile for use in various electrolytes, including those of acidic, alkaline, and chloride compositions. The adaptability of� nickel mesh� anodes to different shapes and sizes expands their applicability to diverse applications. Parameters Material: Nickel� Grade:Nickel� 200,� 205,� 207,� N2,N4,N6,N8 Thicknessï¼?Max� 50mm Widthï¼?50-1000mm Length:500mm-6000mm Mesh� count:1-300� mesh Features 1.Exceptionally lightweight, providing significant energy savings. 2.Demonstrates remarkable resilience against corrosion in both acidic and alkaline environments. 3.Exhibits unparalleled resistance to dry gases at room temperature and can withstand temperatures up to 550â?? in dry chlorine and hydrogen chloride. 4.Boasts impressive mechanical strength, featuring anti-ravel and flexible properties. Application Field Electrochemical Engineering Electrocatalytic Process,Hydrogen Production by Electrolysis Electrochemica Metallurgy Etc. Functional Material Serving as an effective noise reducer, vibration absorber, and wave energy damper. Furthermore, it provides electromagnetic shielding, flame-resistant properties, heat insulation, and other buffering capabilities. Chemical Power Supply Nickel-metal hydride, nickel-cadmium, fuel cell, and other foamed nickel positive and negative electrodes, which doubles the battery performance. Chemical industry The Catalyst and Carrier, Filter Medium (Such as Oil-Water Separator, Automobile Exhaust Purifier, Air Purifier, Photocatalyst Filter, Etc.)
Platinized titanium felt is a specialist material frequently utilized as a flow field or diffuser material in electrolyzer stacks and single cells, particularly on the oxygen (anode) side. This material is made by depositing a thin layer of platinum onto flattened titanium fibers that have been compressed and annealed to create a smooth, flat surface suitable for use in electrolyzers. Platinum coating thickness: 0.5 micron or customized Substrate: titanium fiber felt Felt thickness: 0.2-5.0mm Porosity: 60%-80% Fiber diameter: 10~100 microns Features High electrocatalytic activity: Platinum is known for its high electrocatalytic activity, particularly for the oxygen reduction reaction. When deposited on a titanium felt substrate, platinum forms a highly porous material with a large surface area, providing ample space for electrochemical reactions to occur. High durability: Platinized titanium felt is highly resistant to corrosion and can withstand harsh operating conditions, making it ideal for use in a variety of industrial and scientific applications. Applications Platinized titanium felt is used as an anode material in the production of chlorine and caustic soda in the The platinum coating on the titanium substrate prevents the formation of a passivating oxide layer on the anode surface, ensuring high electrochemical performance and durability. Electrowinning: Platinized titanium felt is used as an electrode material in the electrowinning of metals such as copper, zinc, and lead. The platinum coating on the titanium substrate provides excellent electrical conductivity and corrosion resistance, making it an ideal electrode material. Electrosynthesis: Platinized titanium felt is used as a catalyst support in electrosynthesis reactions, such as the production of organic compounds and fine chemicals. The platinum coating on the titanium substrate enhances the catalytic activity of the supported catalyst, leading to higher yields and selectivity. Electrolytic capacitors: Platinized titanium felt is used as an electrode material in high-performance electrolytic capacitors. The platinum coating on the titanium substrate provides excellent electrical conductivity and corrosion resistance, ensuring high performance and long-term reliability. Water treatment: Platinized titanium felt is used as an electrode material in electrochemical water treatment systems, such as electrocoagulation and electrooxidation. The platinum coating on the titanium substrate enhances the electrochemical performance of the electrode, leading to effective water treatment and disinfection.
Titanium metal powder sintered porous fluidized plate is formed by high temperature forming and sintering of metal or alloy powder, and has a rigid structure. There are a lot of connected or partially connected pores in the substance. Powder particles that are both regular and irregular make up the pore structure. The size and distribution of the pores are related to the size of the particles. The porosity can be adjusted according to the combination of powder particle size and preparation process to meet the actual needs of customers. Advantages: Good permeability, controllable pore size and porosity, stable shape, high filtration accuracy, wear resistance, good mechanical properties, good thermal conductivity, good heat resistance and heat dissipation, backwashing, and repeated use. Titanium sintered porous materials are allowed to be used in the following environments: nitric acid of various concentrations (fuming nitric acid is prohibited), chlorine water, sea water, aqueous solution of sodium hydroxide, carbonate and chloride salt. Properties of Porous Titanium Materials High temperature resistance, normal use 300 Excellent plasticity, high mechanical strength, and machinability. Corrosion resistance, anti-oxidation, can be used in nitric acid, dilute liquid hydrogen, liquid nitrogen environment. Good molding process, one-time molding processing can be carried out according to customer drawings. High filtration precision, good purification effect. No particles fall off, the interior structure is steady, and the pores are uniform. Good air permeability, easy to blow back and clean, and can be regenerated online for repeated use. Wear-resistant and impact-resistant, good mechanical properties Production steps: powder sieving molding vacuum sintering
Features of PP plastic faucet PP is a semi-crystalline material. It is harder than PE and has a higher melting point. Since the homopolymer PP is brittle at temperatures above 0 �° C, many commercially available PP materials are random copolymers with an ethylene content of 1-4% or block copolymers with a high ethylene content. Copolymer PP material has low heat distortion temperature (100C), low transparency, low gloss and low stiffness, but higher impact strength. The strength of PP increases with increasing ethylene content. The Vicat softening temperature of PP is 150 �° C. Due to the high degree of crystallinity, this material has very good surface rigidity and scratch resistance. PP does not have the problem of environmental stress cracking. Generally, PP is modified by adding glass fiber, metal additives or thermoplastic rubber. PP flow MFR range is 1 ~ 40. PP materials with low MFR have better impact resistance, but lower strength. For the same MFR material, the copolymer type has higher strength than the homopolymer type. Due to crystallization, the shrinkage of PP is very high, usually 1.8% to 2.5%. The uniformity of shrinkage direction is much better than PE-HD and other materials. Adding 30% glass additives can reduce the shrinkage to 0.7%. Homopolymer and copolymer PP materials have excellent resistance to moisture absorption, acid and alkali corrosion resistance and resistance to dissolution. However, it cannot resist aromatic hydrocarbons, such as benzene solvents, chlorinated hydrocarbon (carbon tetrachloride) solvents, etc. Use of PP faucet: high quality and low price, non-toxic and tasteless, environmental protection, waterproof, product appearance, quality, sanitary, waterproof, durable, practical, environmentally friendly
Trichloroethylene Also known as: Ethylene Trichloride 1,1,2-trichloroethylene, Chlorylene Molecular Formula: C2HCl3 Molecular Weight: 131.39 CAS No.: 79-01-6 IMCO: 6.1 UN No.: 1710 Product Specification: Item Index Appearance Colorless transparent liquid Trichloroethylene, % min 99.3 Color, max. 15 Water, % max 0.01 Acidity in HCL, % max 0.001 Alkalies in NaOH, % max 0.025 Free Chlorine, % NIL Non-volatile residue, % max 0.005 Acidity after oxidation, % max 0.02 Density by 20, g/cm3 1.460-1.466 Distillation Test (0 101.325KPa) Boiling point Initial, Boiling point Final, 85.5 91 Application: Metal degreasing, as anextraction solvent for oils, fats and waxes Solvent dyeing Dry cleaning as a refrigerant and heat exchange liquid Diluent in paints and adhesives Textile processing Chemical intermediate and aerospace operations (flushing liquid oxygen). In organic synthesis it is used as a fumigant, medicine and in cleaning and drying of electronic parts Packing: TCE is packed in 200L steel drums (UN approved), 280kg net per drum. 22.4mt net in 80 drums per 20s FCL. Bulk product should be transported by tank-trucks in accordance with the relevant safety requirements. Transportation: in transporation, crashing and mixing with acid, oxidant, food and food additives, rain, solarization, high temperature should be avoid. Bottled products should be stored in well-ventilated shed with the treasury or away from the fire source, heat source, a single place, can be stacked. Health Protection: TCE smells like chloroform, and will explode in case of fire or high-heat; it will react with strong oxidizer; it will ventilate phosgene and corrosive hydrochloric acid fumes in case of UV irradiated or heated. Gas masks, eye wears, anti-chemical protective gloves are needed when handling to avoid damage to nervous system. Our advantage: We applied the first-class gas catalyst technology. Our instrument control system is Honeywell DCSC300. Our TCE purity could reach over 99.99% before adding stabilizer.
Magnesium Oxide Board (or MgO Board) is a technologically advanced building material that offers superior performance in every category when compared to traditional wood, gypsum and cement based products. Magnesium Oxide Board is virtually impervious to fire, water, insects; does not feed mold or mildew; is non-toxic, non- flammable and non-combustible; is durable, maintains its dimensional stability-even when wet; and, has exceptional bonding surface. Magnesium Oxide Board is a mineral based green builder product. And it is homogeneous-no de-lamination. Features: WATER RESISTANCE Magnesium oxide inherently has very low water absorption and any moisture is naturally expelled. There is also no deterioration from freeze/thaw cycles. VERSATILITY Whether used on its own as a sheathing, wallboard or underlayment, or in conjunction with other building materials such as plywood, OSB or drywall, it can add tremendous value. MgO has an unlimited number of uses. Fire retardant plywood and OSB, demising walls and insulated exterior wall panels are some of the initial products that offer enormous performance-to-value propositions. FIRE RESISTANCE Magnesium oxide boards are essentially non combustible, with a flame spread of ZERO and a smoke development of ZERO.These properties make it highly effective either standing alone as a sheathing/underlayment or when laminated to other materials. IMPACT RESISTANCE While having the appearance and texture of cement or stone, magnesium oxide board has excellent flexure and tensile properties. All of these properties combine to produce a board with vastly superior impact resistance. Item Index Unites Density 0.9-1.2 g/cm³ Flexural strength â?¥14 Mpa Absorb water saturated flexural strength â?¥16 Mpa Moisture Movement â?¤0.30 % Thermal movement â?¤0.02 % Combustibility Incombustible class A Content of chlorine
Introduction: Deionized Water System for Hospital Test is usually used for rountine chemical laboratory analysis instruments especially biochemical analyzer. The equipement with simple and generous appearance can easily produce water grade II (0.1-1 us/cm ultra-pure water) and water grade III (2-10 us/cm pure water for glass ware washing) which meets standard ASTM, CAP, NCCLS, GB and T6682-2008. Parameter: 1. Source water pretreatment system: PP fiber filter + AC filter + PP filter (1) PP: efficiently filtrate silt, rust, algo, colliod, suspended matter and other inpurities whose diameter is over than 5 um in the water. (2)AC: adsorb residual chlorine, pigment, off-flavor and parts of organic matters. 2. Reverse osmosis system: It has high removal rate more than 99% for high valent ions, colloids, bacteria, organic matter, endotoxin, etc. 3. Ultra pure system: Ion exchange resin using H + exchange cation out the water in the filter ,using OH- exchange anions out the water , the replaced H + and OH- combined to produce H2O, ultra-purified column filling the United States Dow UPW-450 Ultra-pure water for nuclear grade resin, the water resistance of up to 10 MΩ.cm. Features: 1.Water Quality on-line monitoring; accurate and intuitive LCD panel digital display; 2.Polyethylene (PE) and polyacetal (POM) made pressure tank avoids secondary pollution; 3.Automatic water production and storage; 4.Produce RO pure water and UP ultra-pure water. 5.System flushing extends life span of reverse osmosis membrane 6.Pressure alarm display. 7.Automatic water quality alarm. Application: * Biochemical analyzer: Hitachi, Olympus, Beckman, Toshiba, Mindray, etc. * Routine physical and chemical testing; * Analysis experiments. * AA (Atomic Absorption); * AES (Atomic Emission); * HPLC;
We are very glad to offer the best price based on your items list with our min quantiy order. Please check full details in attached file. We offered the best price with hope to get a chance to set up business together with you. Waiting for your feedback. Some information: 1/ Our price is FOB HO CHI MINH PORT, VIET NAM. 2/ MOQ: 1x20fcl (You can mix 3-4 models style/1x20fcl) (5-6 models style/1x40fcl) 3/ Payment: T/T 40 deposit and balance after fax copy Bill or L/C at sight. 4/ Delivery time: 30 days for 1x20fcl, 40-45 days for 1x40fcl HQ Features of plastic fiber: - Anti UV - High color fastness - Resistant to salt and chlorine - Resistant to rain and moisture - Resistant to mould and bacteria - 100% recycle - Strong and durable - Washable and easy maintance Specification: - Aluminium frame with powder coated are fade resistant and UV protected, thickness 1.2mm - Woven with made-in Vietnam plastic fiber. Cushion: Polyurena foam inside/ water resist polyester fabric cover. Top of table with tempered glass. Packaging: wrapping carton paper 2 layers and PE film shrink cover. If you have any other points that you want to make clear, do not hesitate to contact us. Have a nice day! Please see attach file for more list price and picture.
We are very glad to offer the best price based on your items list with our min quantiy order. Please check full details in attached file. We offered the best price with hope to get a chance to set up business together with you. Waiting for your feedback. Some information: 1/ Our price is FOB HO CHI MINH PORT, VIET NAM. 2/ MOQ: 1x20fcl (You can mix 3-4 models style/1x20fcl) (5-6 models style/1x40fcl) 3/ Payment: T/T 40 deposit and balance after fax copy Bill or L/C at sight. 4/ Delivery time: 30 days for 1x20fcl, 40-45 days for 1x40fcl HQ Features of plastic fiber: - Anti UV - High color fastness - Resistant to salt and chlorine - Resistant to rain and moisture - Resistant to mould and bacteria - 100% recycle - Strong and durable - Washable and easy maintance Specification: - Aluminium frame with powder coated are fade resistant and UV protected, thickness 1.2mm - Woven with made-in Vietnam plastic fiber. Cushion: Polyurena foam inside/ water resist polyester fabric cover. Top of table with tempered glass. Packaging: wrapping carton paper 2 layers and PE film shrink cover. If you have any other points that you want to make clear, do not hesitate to contact us. Have a nice day! Please see attach file for more list price and picture.
Product Description Introduction Nine titanium electrodes turn the water to into alkali water and acidic water.Generally, ionized water machines use tap water and ground water to produce alkaline or acidic ionized water through an electrolytic device (electrolytic cell). Alkaline ionized water is produced at the cathode(-), which contains minerals such as calcium, potassium, sodium, and magnesium, and acidic ionized water is produced at the anode(+), which contains minerals such as phosphorus, sulfur, and chlorine within the electrolytic device (electrolytic cell). The alkaline ionized water is potable, and the acidic ionized water can be used for washing purposes. The alkaline ionized water machine generates materials for medicinal purposes and was approved by the Food and Drug Administration. Its effects in treating chronic diarrhea, indigestion, abnormal zymolysis in the stomach and excessive stomach acid were recognized.It is light and thus can be easily placed in the kitchen. Water is released in nine levels i.e. alkali water in four levels, acidic water in four levels and purified water in one level. It has a voice message and is easy to handle. It has a convenient touch sensor and LCD monitor that displays the PH level, ORP and filter life. . * MADE IN KOREA *�9 Platinum Titanium plates. * Front Sliding Door Type * Clear color LCD screen. * Step 9 production (acid alkaline step 4, step 4, an integer) heading. * Automatic cleaning function after every use every * Soft-touch functionality using a capacitive sensor * Color to display each color, step-by-step pH 7 * Each display features step-by-step pH * Self-diagnostic error display function * Large 2 Filter System * Filter life display function * Each use of voice mail features * Heading flow display function * SMPS power control * There is no integers heading emissions of water
Bromochloro-5,5-dimethylimidazolidine-2,4-dione (BCDMH) Chemical name: Bromochloro-5,5-dimethylimidazolidine-2,4-dione CAS NO. : 32718-18-6 Molecular formula: C5H6BrCLN2O2 Structural formula: Molecular weight: 241.5 Properties: white or off-white crystalline powder, slightly dissolved in water,dissolved in chloroform,ethanol and other organic solvent,easy to decompose in strong acid or alkali,stable in dry state. Having slight irritation odour. Uses: mainly used in the disinfection of industrial circulating water, swimming pool, oil field water, spring, hospital sewage, medicinal facilities, aquaculture, food process, hotel, home, warehouse, custom and epidemic-stricken area. Quality index(company standard): Item Index Top-grade Qualified product (BCDMH) Bromochloro-5,5-dimethylimidazolidine-2,4-dione Mass fraction of , % 98.0MIN 96.0 Mass fraction of bromine, % 31.0-35.0 31.0-35.0 Mass fraction of chlorine, % 155-162 155-162 Melting point, Loss on dry(60,1h)% 0.50MAX 0.80 Chroma, YID1925 7.0MAX --- Insoluble in chloroform, % 0.50MAX --- Type of commodities: Tablets:20G/Tablet, 80G/Tablet granule: irregular granule from 8mesh to 30mesh powder Packing: This product is sealed in paper-plastic multiple bag with lining of two PE bags,net weight:25Kg,flake product packaged in 25Kg paper sheet barrel with PE bag lining.This product should be stored in shady dry environment and forbidden to be stored with poisonous or harmful material,preventing from pollution. If you have any demand about my products.
CMIT/MIT-14 CAS NO.: CMIT/MIT 26172-55-4/2682-20-4 Specifications: Item Description Appearance Yellow or yellow-green transparent liquid Content of Active Substance (%) 14.0min Rate of Chlorine 2.5 to 3.5 pH value 2.0 to 4.0 Density (g/ml) 1.27 to 1.33 Application field: The compliant lotion, building materials, electric power metallurgy, oil field chemical engineering, leather, paint coating and spinning prints to dye, the day turn, the antisepsis of cosmetics, deckle, the water transaction etc. realm. Performance characteristics: 1. As a broad-spectrum, long-lasting bactericide to kill many bacteria, fungi and yeasts, the using amount is small. 2. Suitable for use in the medium of the pH value in the range of 2 to 9; free of divalent salt, cross-link no emulsion. 3. Miscible with water; can be added in any production step; easy to use. 4. It has a low toxicity and an appropriate concentration of using, which will lead to no harm completely Usage and Cautions: 1. In water treatment applications, dilute it into a 1.5% aqueous solution first. Add the solution at a quantity of 80 to 100 ppm for one or two times each week depending on the multiplication of microorganisms like bacteria and algae. 2. Avoid direct eyes contact with it for a long period. Once the contact happens, rinse eyes with water without delay. No long-term contact with the skin is allowed. 3. Any contact with reducible metals is forbidden during storage, for example, iron and aluminum, so as to avoid decomposition. 4. Not suitable for use in the alkaline medium of pH> 9.0 due to its poor stability. Any combination of this chemical with highly nucleophilic chemicals, like S2- and R-NH2, will lead to declined quality or even complete failure of the product. Packaging: 250 kg per IBC drum or 250 kg per drum Storage and Transportation: To be stored at room temperature in a dark place; with a shelf time of one year If you have any demand about my products.
