Tile Grout
Liquid Water Proof
Rockwool
Tile Grout
Rockwool, also known as mineral wool, is an insulation material made from natural stone or mineral fibers. The density of Rockwool refers to the mass of the material per unit volume, and it is commonly expressed in kilograms per cubic meter (kg/m�³) or pounds per cubic foot (lb/ft�³). The density of Rockwool can vary depending on the specific product and its intended application. Common densities for Rockwool insulation products range from approximately 40 kg/m�³ (2.5 lb/ft�³) to 200 kg/m�³ (12.5 lb/ft�³) or more. The choice of density often depends on factors such as thermal performance requirements, structural support needs, and the specific application of the insulation.
We have facade insulation board,terrace roof insulation board,partition wall,industrial insulation board,industrial rolls in our product portfolio.
We have all kinds plaster profiles like studs,tracks,omega,corner bead etc. with competitive prices.
* PHOSCAST Phoscast : Phosphate Bonded Castables * PURPOSE customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system. BACKGROUND * Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles. * GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates. Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion * Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected. APPLICATION Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
GFRP rebar is made of high-strength glass fibers along with a highly durable resin. These products are developed as a superior alternative to steel in concrete reinforcement. It is widely used to reinforcing concrete in applications where it is exposed to water, salt water or chemical environments - Typical Advantages: - Non-Corrosive â?? It will not corrode when exposed to a wide variety of corrosive substances - including chlorides - High Strength-to-Weight Ratio â?? best reinforcement for weight sensitive reinforcement - Non-Conductiveâ?? It is excellent electrical and thermal insulator - Excellent Fatigue Resistanceâ?? performs best in cyclic loading solutions - Impact Resistanceâ?? It resists sudden and severe point loading - Magnetic Resistance â?? completely non-effective to electromagnetic fields; excellent for use in electromagnetic testing facilities - Light Weight easy to transport, no need for lifting equipment, easy to handle
The term "cover block" can have different meanings depending on the context in which it is used. In various fields, a "cover block" refers to different things. Construction and Civil Engineering: In the construction industry, a cover block is a small piece of material, often made of concrete, that is used to maintain a specified distance between the reinforcing steel bars (rebar) and the outer surface of a concrete structure. This distance, known as the "cover," is crucial for the durability and strength of the structure. Cover blocks are placed on the rebar before concrete is poured to ensure the correct spacing and to protect the rebar from corrosion. SPECIFICATION: Shape Square Color Grey Size Available in various sizes and for multiple shapes Design Hollow Keep the details as in the products details.
Thermotax is a ready to use air setting refractory mortar. It is air setting mortar having good strength on air drying, forming strong joints & conferring an almost monolithic structure to the fire brick work. Moreover, it is highly suitable for Insulation brick lining work as well as refractory Brick lining work.
Refractory Mortar are heat resistance binding materials which are used in binding Refractory brick lining. Monolithic refractories include refractory castable, refractory mortar, spray mass etc. We offer two types of refractory mortar according to its application including Heat setting mortar : IS-6 Mortar, IS-8 Mortar, 40% To 90% Mortar Air setting Mortar : Set-50 Mortar, Set 50F Mortar
25/50 Kg BAG & 01 Ton Jumbo bag Refractor Castable are heat resistance binding materials which are used in binding Refractory brick lining. Monolithic refractories include refractory castable, refractory mortar, spray mass etc. We offer wide range of refractory castable such as : Conventional Castable Super Castable, Fire crete, HEAT - A Castable, HEAT- K Castable Low & Ultra Low cement Castable MON -45, MON-60, MON-70, MON-80, MON-90 Gunning Castable MONGUN-45, MONGUN-60, MONGUN-70 Insulating Castable INSUCAT-9, INSUCAT-11, INSUCAST-13, INSUCAST-15
Calcium Silicate compound is obtained by reaction of Silica & Calcium oxide. This compound is commonly used to insulate high temperature Pipe, equipment & for fire endurance application. Calcium Silicate have high compressive strength, resistance to damage from tumbling, ability to maintain its properties without loss of insulating efficiency, are rigid, reusable, light in weight and have long life.
1.We use imported base paper from Germany. For solid color, base paper most 80 to 120GSM. For wood base paper is between 70-85 gsm 2. High quality water-base ink- Available over 200 shades in Solid colors and wood grains 3. With clear texture ,high Fidelity meeting international standards. 4. With smooth surface coating 5. Germproof, mould proof, antistatic and wear-resistance. 6. Green environmental protection and Odorlessness which Conforms to the GB18584-2001 standard requirement 7. Can be used for the hot press molding craft, the production efficiency is high. 8. Melamine paper takes shape easily, is widely used for the panel furniture and the decorative yarn. Product Specification: Width: 1230-1260mm or 1300-1800mm Length: 500-1000m For storing: Put it in room to a cool and dry place keep the temperature 20-25°C in room. The best humidity is: 50-60% We can also give you complete decorative solution with Matching Melamine Edge Banding, PU Paper. If you need just need Melamine/prelaminated boards either in MDF / Particle board we can also do so
Essential details Place of Origin: AUSTRIA Brand Name: contact to supplier Model Number: contact to supplier Packaging & delivery Lead time: Quantity(metric tons) 1 - 20 >20 Lead time (days) 5 To be negotiated
Material: hdf Density:+950kg/m3 Door skin width: 660/740/840/920/1020mm Height: 2150mm Surface: natural wood veneer, melamine, enamel paint or plain door skin. We supply hdf moulded door skins, door panels, many designs to choose, with natural wood veneer, melamine finish, painted, with grains. Thickness 3.0 to 4.5mm, width of panel upto 1020. In natural wood veneer : sapele, mahogany, teak, golden teak, walnut. Wenge, black walnut, rosewood, oak, chinese oak, red white oak. Cherry, makore. Many of these veneers can be supplied with engineered veneered surface
We supply: 1. Okume face and Okume back ,hardwood, Combi core MR-AA Grade Face,AA Grade Back in thickness 9mm,12mm,18mm 2.Okume Face and Canarium Back, hardwood combi core MR- A Grade Face , A Grade Back in thickness 9mm,12mm,18mm 3.Okume Face and Okume Back, Eucalyptus core MR+15% Melamine- AA Grade Face , AA Grade Back in thickness 9mm,12mm,18mm 4. Okume Face and Canarium Back, Eucalyptus core MR+15% Melamine - A Grade Face , BGrade Back in thickness 9mm,12mm,18mm We also can do plywood as per customer requirement.
We supply (Garjun) Keruing plywood with 100% core (Garjun)Keriung, face and back (Garjun)Keriung 1220*2440 in thickness 6mm,9mm,12mm,15mm,18mm... Grade: AA/AA Both sides SANDED. Glue: Melamine and MR
We supply Film Faced Plywood ( Shuttering Plywood) with Original Dynea film red brown, brown film (40/128 grade), 30kg, densified Film Faced (15mm to 12mm),11 ply, 12mm thickness (+/- .5mm), 10-15times repetition, 72Hours WBP Glue (Phenol Formaldehyde). Hot press-40minute heating and cooling cycle. Rubber wood + Poly core: 30Kg: Rubber wood + Full core: 30Kg: Eucalyptus + Full core: 38Kg: Benefits: more usages, more load bearing, less scaffolding, save on labor cost. Origin: India, China
