FH SERIES OF PRODUCTS: FH products are Pure nonionic derived the endosperm of guar polysaccharide (Cyamopsos tetragonolobus). The products are unique with ultra-high viscosity with fastest hydration characteristics as shown in Figure 1 below. Also, when added with other drilling components, to seawater, a KCl solution or other aqueous system, the product suspension disperses readily without lumping, even under low-shear conditions generating most of its full viscosity within just a few minutes. PRODUCT COMPATIBILITY: FH series of products are compatible with most of the chemicals and auxiliaries used in drilling operations. However, the products are not compatible with Arabic and Crystal gums. Also, in presence of borates they form elastic gel. PRODUCT APPLICATIONS: FH series of products are natural, high viscosity, fast hydrating non-Newtonian hydrocolloids with suitable cross linking components in diesel slurries and are versatile for continuous mix applications, where extremely fast hydration and subsequent viscosity development is required. They are excellent viscosifiers, stabilizers, thickeners and suspending agent for use in oil-drilling, workover fluids and several other oilfield applications like hydraulic fracturing, oil well stimulation, mud drilling, oil well capping, flocculent and liquid shoring etc. The product is used as a surfactant; synthetic polymer and deformer ideally suited for all rheological requirements of water based and brine based drilling fluids. Specifications:- PRODUCT : FH-35 FH-38 FH-42 CAS No. : 9000-30-0 9000-30-0 9000-30-0 Granulation : FINE FINE FINE APPEARANCE : OFF WHITE POWDER MOISTURE : 8% Max. 8% Max. 8% Max. PROTEIN (N X 6.25) : 5.0% Max 5.0% Max 5.0% Max ASH : 1.5% Max. 1.5% Max. 1.5% Max. ACID INSOLUBLE RESIDUE (A.I.R.) : 3% Max. 3% Max. 3% Max. CARBOHYDRATE (incl gum by difference) : 82% Min 82% Min 82% Min pH (1% Solution) : 5.5 ? 6.5 5.5 ? 6.5 5.5 ? 6.5 VISCOSITY : (0.48% Product in 2% KCL Sol. 2.5 mins mix @1500 RPM in waring blender) Fann 35sa Viscometer at 300 RPM, 25�C 3 Mins : 35 3 Min:38 3 Mins : 42 5 Mins : 37 5 Mins : 39 5 Mins : 43 30 Mins : 39 30 Mins : 42 30 Mins : 45 60 Mins : 40 60 Mins : 43 60 Mins : 47
Shubhlaxmi industry is a manufacturer/processor and exporter of Black Mustard Seeds. The seeds are packed with its richness and goodness for you to open it up. We bring you the supreme quality of seeds that satiates the end user. The botanical name of black mustard seeds is Brassica nigra and it belongs to the family Brassicaceae. They are small, round, black or dark brown in color. They are native to Middle East but as of now, they are cultivated widely in India. They are commonly known Sarson. Black mustard seeds are mostly used in tempering food. The seeds are added to warm cooking oil which then pops up to add rich flavor and aroma. Mustard sauce is commonly used these days as salad dressing. Black mustard seeds can be roasted to make it into powder to add to pickles. They seeds are bitter in taste; hence when powdered, it should be carefully used. Mustard seeds help in increasing appetite. They can neutralize toxins. They are a good source of minerals and Omega-3 fatty acids. Specification HS Code : 09109914 Grade : Machine Cleaned & Sortex Cleaned Purity : 98%/99%/99.50% Bold & Small Moisture : 7 To 8% Max Total Ash : 6-8% Max Salmonella : Absent/25gms Packing : 5/10/25/50 Kg Net Pp. & Brand Packing Quality Assurance : Sgs,geo-chem Loading Capacity : 24mt In 20'fcl & 26mt In 40'fcl
Technical Data Sheet Property Average Value Gravity@15.6oc : 0.859 Max SPI: 33.45 Sulphur: 1.2-1.5 Max Water & Sediment Content: 0.2 Max Water Content: 0.1 Max Salt Content: 8 Max Carbon Residue: 4 Max Reid Vapour Pressure: 0 Pour Point: 0.35 Ash: 0 Asphalt : 1 Max ASTM Stabilized Gravity: Degree 3.7 Recovery @50oc: 0.8 Min @100oc: 8 @200oc: 28 @250oc: 37 @300oc: 47 Total Distillate: 47 Total Residue: 2.5Max
Tumi Ishi blocks are small chunks of wood, cut kind of like a gemstone. Basically the idea is you are supposed to stack them all up. Tumi ishi Wood Balancing Stones for Baby is a new take on the classic wooden building block. Unlike standard square blocks, these blocks have many sides making them more challenging to stack Type: Block Set, Other Classic Toys Material: Wood Size: 3-6cm Color: Natural color Logo: Customized Logo Age Range: 0 to 24 Months, 2 to 4 Years, 5 to 7 years, 8 to 13 Years,... Usage: Relaxing, Educate, Simulate brain development for kids Packing: Bag/carton
Soybean Oil" is a vegetable oil that's extracted from the seeds of the soybean plant. Between 2018 and 2019, around 62 million tons (56 million metric tons) of soybean oil were produced around the globe, making it one of the most common cooking oils available. Physical Characteristics Physical State : Liquid Appearance : Light Yellow, Clear and Brilliant Taste : Bland Odor : Bland Color: 5 - 13.5 Yellow / 0.6 - 2.0 Red Quality Standards Free Fatty Acid %: 0.05 - 0.1% Peroxide Value meq/kg: 0.5 - 1.0 meq/kg Refractive Index @ 40oC: 1.4666 - 1.47 Iodine Value (Wijs): 123 - 139 Moisture %: 0.05 - 0.1% Cold Test: 5.5 hrs OSI @ 110oC: 5.5 - 6.0 hrs Saponification Value: 191 - 192 Specific Gravity @ 25oC: 0.915 - 0.925 Smoke Point: 460 - 465oF Flash Point: 650 - 655oF Fire Point: 690 - 695oF Fatty Acid Properties Typical Fatty Acid Profile (major acids) Type Name C14:0 Myristic 0.1% C16:0 Palmitic 8.0 - 14.0 % C16:1 Palmitoleic 0.0 - 0.2% C17:0 Heptadecanoic 0.0 - 0.1% C17:1 9-Heptadecenoic 0.0 - 0.1% C18:0 Stearic 3.0 - 5.0 % C18:1 Oleic 20.0 - 32.0 % C18:2 Linoleic 47.0 - 57.0% C18:3 Linolenic 5.8 - 8.2 % C20:0 Arachidic 0.1 - 0.5% C20:1 Eicosenoic 0.2 - 0.3% C22:0 Behenic 0.2% C24:0 Lignoceric 0.0 - 0.1%
Soybean Oil" is a vegetable oil that's extracted from the seeds of the soybean plant. Between 2018 and 2019, around 62 million tons (56 million metric tons) of soybean oil were produced around the globe, making it one of the most common cooking oils available. Physical Characteristics Physical State : Liquid Appearance : Light Yellow, Clear and Brilliant Taste : Bland Odor : Bland Color: 5 - 13.5 Yellow / 0.6 - 2.0 Red Quality Standards Free Fatty Acid %: 0.05 - 0.1% Peroxide Value meq/kg: 0.5 - 1.0 meq/kg Refractive Index @ 40oC: 1.4666 - 1.47 Iodine Value (Wijs): 123 - 139 Moisture %: 0.05 - 0.1% Cold Test: 5.5 hrs OSI @ 110oC: 5.5 - 6.0 hrs Saponification Value: 191 - 192 Specific Gravity @ 25oC: 0.915 - 0.925 Smoke Point: 460 - 465oF Flash Point: 650 - 655oF Fire Point: 690 - 695oF Fatty Acid Properties Typical Fatty Acid Profile (major acids) Type Name C14:0 Myristic 0.1% C16:0 Palmitic 8.0 - 14.0 % C16:1 Palmitoleic 0.0 - 0.2% C17:0 Heptadecanoic 0.0 - 0.1% C17:1 9-Heptadecenoic 0.0 - 0.1% C18:0 Stearic 3.0 - 5.0 % C18:1 Oleic 20.0 - 32.0 % C18:2 Linoleic 47.0 - 57.0% C18:3 Linolenic 5.8 - 8.2 % C20:0 Arachidic 0.1 - 0.5% C20:1 Eicosenoic 0.2 - 0.3% C22:0 Behenic 0.2% C24:0 Lignoceric 0.0 - 0.1%
Pale yellow liquid at room temperature characteristic odor and taste or nearly odorless, free from rancidity or any objectionable odor and taste. Each batch of materials shall undergo strict sampling,inspection and screening for guaranteeing the affluent oil production and the excellent oil fragrance. Groundnut OIL Taste Neutral Impurities Negative Free Fatty Acid ( % ) max 0,10 Moisture ( % ) max 0,05 Peroxide Value ( meq O2/ kg ) max 5 Specific gravity at 20 degr C 0,91 - 0,93 Iodine value ( g / 100 g ) 82 - 110 Colour Lovibond 5 1/4 " Red max 2,5 Colour Lovibond 5 1/4 " Yellow max 25 C 12:0 C 14:0 (Myristic Acid) C 16:0 ( Palmitic Acid ) 6 - 14 C16:1 (Palmitoleic Acid) C 18:0 ( Stearic Acid ) 1 - 5 C 18:1 ( Oleic Acid ) 35 - 72 C 18:2 ( Linoleic Acid ) 13 - 44 C 18:3 ( Linolenic Acid )
We are supplier and exporter of All types of ceramic Tiles. We have been exporting Ceramic Tiles to more than 15 countries. We deal in most of the Sizes and Variety of Tiles ie :- 1. 300X450 MM Wall tiles 2. 300X600 MM Wall tiles / Vitrified Tiles 3. 200X600 MM Wall tiles 4. 300X300 MM Wall tiles 5. 250X375 MM Wall Tiles 6 600X600 MM Vitrified Tiles / Double Charge / Full body tiles / Porcelain tiles 7 600X1200 MM Vitrified Tiles /Full body tiles 8 Slab Tiles 9 Subway Tiles 10 Quartz Stone 11 Engineered stone
Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor
Descriptions: Cuttlebones are an excellent calcium source for birds. The rough edible surface helps to trim the beaks of birds as well as provide something for your bird to chew on. The cuttlebones can also be cut into smaller pieces or ground into a powder and used as a nutritional supplement for all types of birds. Features: Provides natural calcium and minerals Derived from natural cuttlefish Natural surface keeps beaks trim and sharp Suitable for cockatiels Specification: Material: Cuttlefish bone Size: 5~20cm Quantity: 3~5 Pcs/bag Note: 1.Transition: 1cm=10mm=0.39inch 2.Please allow 0-3cm error due to manual measurement. pls make sure you do not mind before you bid. 3.Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you! No Retail Package Package Contents: 1 Bag x Cuttlefish Bone
We are supplier of Reinforcement Bars. can supply REBARS as per below: -Size: 6mm to 50 mm -Length: 6 meters up to 16 meters -Packing: Once folded bundles available. hese corrugated steel bars are used as tension devices in the construction of concrete slabs and walls, as well as decorative/ornamental grille work. When used in concrete constructions, these help to strengthen and hold concrete when it is compressed, and come in a wide variety of sizes to fit various building construction needs. At ARC. AVAILABLE IN 3/8 (10mm), 5/8 (16mm), (20mm), (12mm), 1 (25mm) and 1 (32mm)
APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.
We have avaliable to load light naphtha as following terms and conditions. If you have a real buyer in China or Some where else, please. advise. THE PRICE IS GOOD. If you can give as the discharging port, we also can offer CFR Price Price Shall Be Expressed In Us Dollars, Per Metric Ton Of The Product Delivered Hereunder On B/l Quantity Safe Fraud Of Manifest Error, On Fob One Safe Port/one Safe Berth Marsa, Brega Basis To Be Calculated As Per The Following Price Formula: Pricing period as : BL+3, BL=0 The Final Price Of The Goods Shall Be Determined As The Average Of Mean Quotations As Published In Platts European Marketscan For Naphtha Under The Heading Fob Med Italy During The Pricing Period Minus A Discount Of Usd 20.00 (forty Seven Point Zero Zero) Us Dollars Per Metric Ton In Air. Payment : By Confirmed LC At Five (5) New York Banking Days After Completion Of Discharge At Discharge Port (cod Date Equals Day Zero) Quantity : 40 K Mt Shipment : Prompt Origin : Libya
Gremlog Trading DMCC is pleased to announce the availability of Waste electrical and electronic equipment (WEEE) plastic in the United Arab Emirates. WEEE plastic, sourced from Waste Electrical and Electronic Equipment, is instrumental in advancing recycling and sustainability efforts. This material is recovered from obsolete electronic devices and processed into valuable raw materials for manufacturing new products, thereby significantly reducing environmental impact. By offering WEEE plastic, Gremlog Trading DMCC aims to bolster eco-friendly initiatives and promote a circular economy in the region. Businesses can now access high-quality recycled plastic for a variety of applications, including packaging, automotive components, and construction materials, thus contributing to a more sustainable future.Additionally, we offer WEEE plastic in four sizes: 0-1 mm, 1-2 mm, 2-4 mm, and 4-8 mm, to meet diverse industry needs and specifications
We specialize in offering recycled mill scale, which refers to the reclaimed or repurposed mill scale derived from hot rolled steel surfaces. Instead of being discarded as waste, this recycled mi l scale undergoes meticulous processing to extract valuable components or transform it into usable materials. This versatile resource finds application across various industrial sectors, including iron and steel production, where it serves as a source of iron oxides in blast furnaces or electric arc furnaces. Moreover, it contributes to cement production as an essential component in cement clinker, enhancing the chemical composition of the final product. Additionally, recycled mil scale finds utility in diverse industrial applications, such as the production of ferrous sulfate for agricultural and water treatment purposes, or as a constituent in specialty products and construction materials. By offering recycled mil scale, we actively contribute to minimizing waste generation and conserving resources, ensuring compliance with quality standards and environmental regulations through proper handling and processing protocols.
Gremlog Trading DMCC emerges as a pioneering force in the recycling landscape, offering recycled silica sand in sizes ranging from 0-1mm to 1-4mm. Leveraging the inherent advantages of repurposed silica-based spent foundry sands, Gremlog Trading DMCC champions sustainable practices within the metal casting industry. By providing recycled silica sand, Gremlog Trading DMCC contributes to energy conservation, reduces reliance on virgin materials, and delivers cost-effective solutions for both producers and end users. Gremlog Trading DMCC's recycled silica sand stands as a versatile resource, poised to revolutionize not only traditional applications but also industry-specific needs. With its origins in spent foundry sands from the metal casting industry, this recycled silica sand finds renewed purpose as a foundational material for roads, an essential ingredient in manufactured soil, and a component of soil less media like potting soil. Moreover, its inherent properties make it ideal for reuse within the metal industry, contributing to the circular economy by minimizing waste and maximizing resource efficiency. Gremlog Trading DMCC's commitment to innovation and sustainability ensures that their recycled silica sand remains a cornerstone of eco-conscious practices across various sectors, paving the way for a greener, more efficient future.