Calcium Silicate Insulation Board At 650 Suppliers and Manufacturers

METHOD OF APPICATION: * Mastic compound application consist of two coats of. Primer ,Primer and followed by Mastic compound in recommended thickness, ranging from min. 12mm to 25mm in one or two layers to achieve desired thickness without any pin hole and crack. 1). Surface preparation and application of Primer: Refer application method of Primer. 2). After doing necessary surface preparation and application of primer coating, area to be installed with Mastic compound should be divided in to equal no. bays. To maintain even thickness required, place wooden or aluminum batten. Mastic compound is then broken in small pieces and put it in heating pan. While heating, keep material moving to avoid burning. It is heated until it comes in a uniform consistency and then applied on the surface and works it with wooden float, to achieve uniform thickness and smooth surface free from any pinholes. CHEMICAL RESISTANCE PROPERTIES: * Mastic compound has good resistance to weak, diluted acids, alkalis salts etc. It is not recommended to use against strong acids, oxidizing acid solvents, oil and fats STORAGE & PACKING: * Keep Mastic compound away from direct sunlight, heat solvents etc. Under this condition, its shelf life is unlimited. It is supplied in cake form and approx. wt. is 10 kgs. HEALTH & SAFETY: * Handle melted Mastic compound compound very carefully . Avoid contact with skin. It is advisable to wear protective wears at the time of use of Mastic compound and all other our products. This information, given in good faith, is based on results gained from experience and tests. However, all recommendations or suggestions are made without guarantee since the conditions of use are beyond our control.

APPLICATION OF SK-HB K-SILICATE MORTAR : * K-SILICATE is used for jointing Acid Resisting brick in construction of vessels in suited for construction of fume chambers and stacks handling hot, dry Acid fumes and vapors. It is also used for jointing chemical resisting stoneware pipes. K-SILICATE cement is good bedding material for Acid â?? Resisting bricks and tiles. The concrete surface needed protection should be dryed, clean and rough. The bricks or tiles will be set with K-SILICATE cement over concrete surface applied with a suitable an impermeable interliner. When Bedding and Jointing Materials are the same. On the treated surface bricks or tiles are bedded to a thickness of about 6 mm and tamp gently with a wooden piece till the paste squeezes out of joints. The paste that is squeezed out of the joint should be removed by trowel with good finishing. After the mortar of the joint is dryed treat the joints with 20% Hydrochloric Acid Solution by means of brush. A.R.lining should be always in contact with Acid and not with water. Concrete subtract like Floor, Wall, tanks and similar surface should be protected with a membrane of Bitrok Mastic or compound steel tanks should be protected with rubber or PVC subjected to chemical conditions and temperature of chemical media. The Brick lining is recommended over the protective layer of Bitrok Mastic. When Bedding and Jointing Materials are Different. Spread the silicate type mortar about 6 to 8 mm thick on the back of the tile or brick. Press the tile on the bed leaving required space for joints between tiles for bricks. After the bedding mortar is set, fill Mp the joints with specified cement.PRODUCT DATA SHEET FOR SK-HB ( K-SILICATE) MORTAR A general purpose cement for acid conditions Resistant to High & medium concentrations of most of the common organic and inorganic acids except Hydroflouric acid. Recommended where the concentration of the acid is high suitable for high temperature. Unsuited to aqueous solutions, alkaline conditions. PREPARATIONS OF MORTAR : * Measure 1 part by weight of K-SILICATE solution into a suitable mixing pan. * Add slowly and gradually 3 parts by weight K-SILICATE mortar and mix thoroughly to form a smooth mortar. * In hot season very large batches of mortar will become stiff quite rapidly therefore small batches, not exceeding 4 to 8 kgs. Will be prepared. * The cement mortar will be used before it starts setting.

This is chemical setting Furan based chemical resistant mortar which is combination of Liquid and Powder, when mixed in proper proportion from workable mortar which after setting and curing give of liquid and give black highly cross linked composites. Furan When set and cured is resistant to highly corrosive acids, alkalis and to powerful organic solvents such as ketones, Aromatic and Chlorinated solvents. It has extreme resistant to Acidic & alkalis, Salts, Greases and Detergents. It resists to Organic & Inorganic acids at their boiling temperature. It is suitable against mild chlorine Gas (dry) phosphorous trichloride, pyridine at room temperature. Furan is especially useful where resistance to mixed media such as aqueous acids /alkalis and organic solvents is needed in chemical plant process and waste streams. Carbon filled Furan is used against corrosive effect of hydrofluoric acid & its salts. PREPARATION OF FURANE MORTAR : Mortar consist of Furan solution and Furan powder. The average mixing ratio necessary to obtain mortar with good working consistency is 1 part by weight Solution & 3 part by weight powder. The ratio will vary slightly depending on temperature and working conditions.Stir the liquid thoroughly before using. Place liquid in a suitable shallow mixing pan. Add powder by weight in the solution mix thoroughly and rapidly until all lumps are dispersed and the mortar is completely homogenous. Spread out the mortar in a thin layer, not more than ¾ thick, to dissipate the heat of reaction and lengthen the working life. Batch size can be varied depending upon the temperature and the speed with which the masons are working. Very large batches will become stiff quite rapidly. Make sure that all the Furan Motrar is used from the pan before another batch is mixed.When working at temperature above 40 C, very small batches not more than 2 Kgs, should be prepared. When working at temperature below 15C the liquid should be kept warm.

DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.

Bitumen Primer * Bitumen Primer is Bituminous air curing ready mixed Acid & Alkali resistant special primer. Application * Concrete surface must be clean, dry and rough. No primer should be applied over smooth and wet surface. * After cleaning the concrete surface, one coat of Bitumen Primer should be applied with brush and allow to dry thoroughly. * The drying time will depend upon the temperature. * 24 Month at the temperature 30C (+2OC) Packing * Bitumen Primer: 25 Liter Drum Note * Bitumen Primer contains volatile and slightly toxic solvent. Keep away from spark and open flames at working area. * Bitumen premier it is manufactured using bitumen solution which is used for sealing of prime porous and non-porous surface, and also to protect residential and commercial building. * Bitumen Primer is used to protect substrate against corrosive attack, is suggested to apply anti-corrosive primer.It is best for protection against sub-striate against atmospheric corrosion and chemical corrosion. It is a mixed substance made up of organic liquids that are highly sticky, water proof, viscous,acid proof as with all surface coating, good Bitumen Premier is used for long life of the system. it is applied by brush or roller and allowed to dry before any water proofing treatment so to avoid solvent it is used in defects such as cracks, broken mortar joints, etc. are to be repaired prior to Bitumen primer application. Product Details: Grade Standard Technical Grade Physical State - Liquid Usage - Industrial Color - Black Characteristics: Appearance/Color - Pasty liquid/ black Chemical Base - Bituminous rubber emulsion. Density - 1.0 kg/l Curing Speed/ Rate - 3 - 4 hours Tack free after - 5 - 10 hours Cured after - 2 - 4 days (Dependent on ambient Solid Content by - temperature, substrate temperature, Weight - relative Water Content by weight - humidity and thickness of the coating) Bitumen Content - 41% by weight - Thixotropic (The viscosity can be adjusted by - Viscosity adding up to max. 5% of clean water. - Stir well prior use) - For light protection: 1.0 mm min. Coating - For greater protection: ~ 1.5 - 2.0 mm Thickness applied - in two coats. Water Penetration - 48 h, 1 bar: 78.5 cm2: 0 ml under Hydrostatic - 96 h, 4 bar: 78.5 cm2: 33 ml Pressure - Water vapor 6 x 10-7 mg / hmPa Permeability Service - -30 C to 200 C Temperature - Adhesion Concrete - Very good, Timber: Very good, Metal: Moderate Glass: Poor

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : RED SHALE Type Acid Resistant Brick Size (mm) 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions Heavy thermal shock Typical Physical Properties of GANESHAS Acid and Chemical Resistant Brick Characteristic RED SHALE ACID RESISTANT BRICK Test Standard Bulk Density, gm/cc - 2.3 to 2.35 ASTM C-20 -Water Absorption, % - 0.1 to 1.5 IS 4860-1968 Apparent Porosity, % -0.5 to 1.75 S 4860 Acid Solubility (H2SO4), Loss in Mass,% -0.1 to 1.8 ASTM C-279 Modulus of Rupture, PSI -2133 to 3555 ASTM C-67 Compressive Strength, Kg/cm2 - 700-900 IS 4860-1968 Abrasion Resistant , Volume in mm3 -69 to 85 EN 102 Surface Hardness, MOHS Scale - 7

PRODUCT DATA SHEET ACID RESISTANT BRICK Material : FIRECLAY Type Acid Resistant Brick Size (mm) : 230 (LENGTH) X 115 (WIDTH) X 100,76,65,50,40,38,30,25 (THICK) Specification : ASTM C279, ASTM C410, IS 4860-1982 DESCRIPTION : * We offer premium quality acid resistant bricks Red â?? Shale , tiles and special shapes. We also offer customized sizes as per clients' requirements. Our acid bricks comply with ASTM C279 Type-III, ASTM C410 Type H, L, and Indian Standard 4860 - 1982 Class-I for all applications where low absorption and high acid resistance is required. FEATURES OF ACID RESISTANT BRICK: * Excellent resistant against wide range of chemicals except hydrofluoric acid, high abrasion resistance, low wearing properties, High Thermal resistant to sudden change in temperature AREA OF APPLICATION: Chemical Analysis (Average) Acid and Alkali Storage Tank Farms Demineralization plants and Water treatment plants Chimney inside lining, FGD linings Towers and Columns Process Vessels and Tanks Sewerage Treatment Plants and Lines Industrial Flooring and Bund Areas Chimney and Flue Gas Linings Hoppers and Chutes SiO266.4 Al2 0324 TiO21.1 Fe2 O31.1 K2 O + Na2 O2.5 NOT RECOMMENDED: HF acid or other fluoride solutions - Heavy thermal shock Characteristic Fireclay Type Acid Resistant Brick - Test Standard Bulk Density, lbs/ft3 - 2.25 to 2.30 ASTM C-20 Water Absorption, % - 0.1 to 1.8 ASTM C-20 Apparent Porosity, % - 4.05 to 4.14 ASTM C-20 Acid Solubility (H2SO4), Loss in Mass,% - 6.1 to 6.8 ASTM C-279 Modulus of Rupture, Mpa - 14.6 ASTM C-67 Compressive Strength, PSI - 15500 to 17250 ASTM C-67 Abrasion Resistant , Volume in mm3 - 71 to 96 EN 102 Surface Hardness, MOHS Scale - 7 Thermal Conductivity, BTU-in/hr-ft-F - 6.94 to 7.12 ASTM C-236 Thermal Expansion Coefficient,in/in/Fx10-6 - 2.6 to 2.8 EN 103

Acid / Alkali Resistant Tiles/Bricks * Our Acid proof tiles, Acid alkali resistant tiles, Chemical resistant tiles are fully vitrified tiles which are manufactured using special non ferrous clay, processed at extremely high temperatures this process causes the raw materials to fuse and form a compact mass with an extremely low water absorption of less than 0.5% resulting in the formation of a very strong body with a flexural strength of 38 N/mm2, solid through color fade proof with a very hard surface Mohs hardness of 7. * The acid resistant tiles come in a range of sizes and thicknesses from ranging from 8-25mm. Our acid proof tiles meet stringent specification norms of IS 4457:2007 and relevant ASTM/DIN standards which ensure excellent performance in Acid/Alkali/Chemical (expect Hydrofluoric acid and its derivatives). Corrosion Protection Applications * Factory Floors subject to corrosion from Chemicals, Acids, Oil & Solvents * Pickling tank and surrounding areas * Food & Beverage Industry flooring * Battery rooms and Control rooms * Demineralization plants * Walls of washing and Paint shop areas * Acid Resistant Tiles Manufacturers India * Our acid proof tiles provide excellent abrasion resistance, anti-skid properties for worker safety and high aesthetic appeal. We also provide specialized corner tiles for reducing chances for acid attack through construction joints. Our standard sizes are 200x100, 200x200 & 300x300 millimeters.

HIPS Regrind White-Mix Thermoplastic PS has two representatives as GPPS and HIPS resin. In particular, PS HIPS plastic is more popular thanks to many advantages and applications. PS HIPS belongs to the group of hard, transparent resins that are easy to color, machined by suction lamination method and easy injection technology. Common HIPS applications: In packaging technology, it is used as a single-layer packaging for products that do not require strict antioxidant requirements. Make coating HIPS plastic film to increase water vapor and gas resistance. Making a printing surface to increase printing ability, making the outer plastic packaging with the ability to tear easily and create gloss. Making bottle caps, pen cases, jewelry boxes, beer tanks, fresh food containers. Making pharmaceutical bottles, pipes, cap for solvent containers. Making high-frequency insulating materials, insulation clamps. Making imitation leather sandals, textile packaging. Pressing students' tables and chairs, pressed motorcycle details, yogurt cup, plastic candy tray. MATERIAL: HIPS Regrind White-Mix CATEGORY: HIPS TYPE: Regrind White-Mix SPECIFICATION Product- HIPS regrind post production from Yogurt caps Contamination â?? up to 2% foil metalizing (cover of the yogurt caps). Food grade material Post - industrial Sheet Extrusion & Vacuum forming Origin: Spain LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days

HIPS Regrind from post consumer materials Thermoplastic PS has two representatives as GPPS and HIPS resin. In particular, PS HIPS plastic is more popular thanks to many advantages and applications. PS HIPS belongs to the group of hard, transparent resins that are easy to color, machined by suction lamination method and easy injection technology. Common HIPS applications: In packaging technology, it is used as a single-layer packaging for products that do not require strict antioxidant requirements. Make coating HIPS plastic film to increase water vapor and gas resistance. Making a printing surface to increase printing ability, making the outer plastic packaging with the ability to tear easily and create gloss. Making bottle caps, pen cases, jewelry boxes, beer tanks, fresh food containers. Making pharmaceutical bottles, pipes, cap for solvent containers. Making high-frequency insulating materials, insulation clamps. Making imitation leather sandals, textile packaging. Pressing students' tables and chairs, pressed motorcycle details, yogurt cup, plastic candy tray. MATERIAL: HIPS Regrind from post consumer materials ,Yes No Fr, NO pc abs, no iron, no circuit etc CATEGORY: HIPS TYPE: Regrind SPECIFICATION: Hips from post consumer materials.Yes No Fr, NO pc abs, no iron, no circuit etc. Hips per month 52 mt Origin: Bangladesh LOADING WEIGHT: 24 Ton FOB (USD/Ton): 650$ - 850$ Packaging: Jumbo Bag Est. Shipping Time: 15, 30, 45 days

Fly ash is a by-product produced while burning finely ground coal in a boiler to produce electricity. It is removed from the plant exhaust gases primarily by electrostatic precipitators or baghouses and secondarily by scrubber systems. Physically, fly ash is a very fine, powdery material, composed mostly of silica. Nearly all particles are spherical in shape. Fly ash is a pozzolan, a siliceous material which in the presence of water will react with calcium hydroxide at ordinary temperatures to produce cementitious compounds. SiO2, Al2O3, Fe2O3 and occasionally CaO are the main chemical components present in fly ashes. Fly ash significantly improves concrete performance in different ways and also provides many benefits in cement and non-cement applications. Fly Ash colour can vary from grey and dark grey, yellowish tan and light to brownish. ADVANTAGES OF FLY ASH IN CONCRETE Fly Ash is a Pozzolan Improves concrete workability and lowers water demand Sulfate and Alkali Aggregate Resistancet Rise in compressive strength over time Environment friendly CEMENTATION Fly Ash is optimized for its fineness while reducing the water demand and improving the chemical compositions to maximise its benefits when used in concrete. Fly-ash can also be used as an add-on to concrete mixture with pozzolanic and/or latent hydraulic properties. We at CEMENTATION selectively collect fly ash and subject to rigorous testing, further refines these collected materials to produce quality fly ash products meeting the needs of our customers.

Description 1. High purity (Sn99.99 Sn99.95 Sn99.90), excellent weldability, good infiltration. 2. Clean, beautiful. After welding, insulation, high resistance, low ionic contamination, PCB board welding residual minimal. 3. Good oxidation resistance, low tin slag and cost savings. 4. Solder joint is bright, full and uniform. 5. Economical and can produce the lowest consumption of the solid solder joints. Application Tin ingot is widely used as a coating material in High precision electronic Products, and other requirments of precision welding products, general electronics, food industry packaging, automotive and electrical industry, and hightemperature resistant products.

Quartz a crystal form of silica is found in a massive forming hill. Quartz is a mineral that's easily available from the crust of earth. And yet, it's quite valuable for its vast usage. Applications: - GLASS CERAMIC ABRASIVE PAINT SODIUM SILICATE FERRO SILICON REFRACTORY Millimeters Scale ASTM Scale 0.08-0.15mm 100-200 Mesh 0.1-0.2mm 70-120 Mesh 0.2-0.4mm 40-70 Mesh 0.3-0.6mm 26-40 Mesh 0.6-0.12mm 16-26 Mesh 1.2-2.5mm 8-16 Mesh 2.5-4.0mm 6-8 Mesh 4.0-6.0mm 4-6 Mesh 6.0-8.0mm 3-5 Mesh 38 Microns 400 & 200 Mesh Index Compound Unit Result 1. Silica - (SiO2) % 98.11 2. Alumina - (AI2O3) % 00.49 3. Iron - (Fe2O3) % 00.03 4. Titanium - (TiO2) % 00.03 5. Calcium - (Cao) % 00.64 6. Magnesium - (MgO) % 00.07 7. Soda - (Na2O) % 00.09 8. Potash - (K2O) % 00.03 9. Loss on Ignition - (LOI) % 00.20

Introduction: - Feldspar is primarily used in industrial applications for its alumina and alkali content. Feldspar is a naturally occurring anhydrous, inorganic, igneous rock. The fusibility of the mineral makes it useful raw material for many applications and the purity is the indication of better fusibility in the application. There are two types of it depending On Na2O and K2O SODA FELDSPAR POTASH FELDSPAR Applications: - CERAMICS ENAMEL FRITZ & GLAZED INSULATORS GLASS MILD ABRASIVES PICTURE TUBES SANITARYWARE TABLEWARE VITRIFIED TILES WELDING ELECTRODE Available Mesh Size: - 100 - 500 MESH Custom sizes and Material of required specifications can be made in case of Bulk and Regular orders. TYPICAL CHEMICAL COMPOSITION OF POTASH FELDSPAR Index ompound Unit Result 1. Silica - (SiO2) % 66 - 68 2. Alumina - (AI2O3) % 17 - 18 3. Iron - (Fe2O3) % 0.03 - 0.06 4. Titanium - (TiO2) % 0.03 - 0.06 5. Calcium - (Cao) % 00.00 6. Magnesium - (MgO) % 00.00 7. Soda - (Na2O) % 2 - 3 8. Potash - (K2O) % 10 - 12 9. Loss on Ignition - (LOI) % 0.10 - 0.20 TYPICAL CHEMICAL COMPOSITION OF SODA FELDSPAR Index Compound Unit Result 1. Silica - (SiO2) % 68 - 72 2. Alumina - (AI2O3) % 17 - 18 3. Iron - (Fe2O3) % 0.10 - 0.15 4. Titanium - (TiO2) % 0.03 - 0.06 5. Calcium - (Cao) % 0.05 - 0.20 6. Magnesium - (MgO) % 0.10 - 0.15 7.Soda - (Na2O) % 9 - 10 8. Potash - (K2O) % 0.50 - 0.20 9. Loss on Ignition - (LOI) % 0.10 - 0.20