Segmental Sewer Air Test Kits Segmental testing is used to identify and pinpoint leaking joints in sewer collection systems. The inflatable plugs are winched in tandem down the line and positioned to straddle the joint or span to be tested. Once the plugs are inflated, a low-pressure air test is performed to verify the integrity of the joint or span and to localize sewer defects. Lateral connections and lines can also be tested when there is an above ground access for the introduction of an inflatable sewer plug from the cleanout. The mainline plugs are positioned on each side of the lateral connection and the push plug is inserted into the cleanout access isolating the lateral connection and lateral line. Flexible Push-Type Test Rigs are used to perform low pressure air tests on laterals from an above ground access. Contact us with your application and requirements.
Flexible Push-Type Test Rig for Segmental Pipe Testing Logiball Push-Type Test Rig is used for segmental air testing of lateral lines, from the cleanout or above ground access. The standard test chamber between the two inflatable bladders is 5 feet long. A 3/4 semi-rigid hose is used as a push rod and to inflate both bladders in one operation. Air for the test chamber is supplied thru a 1/2 semi-rigid hose to be used as a second push rod and lateral test line. Logiball Flexible Push-Type Test Rig can be used in lines 4 to 6 inch in diameter. For sealing defective laterals using chemical grout, use the Flexible Push/Pull Type Packers The control system for inflation & test is offered separately.
Keep the flow under control when flushing fire hydrants. Avoid the washout of the surrounding soil. Increase rapidity and security when flushing hydrants. Keep traffic interruptions to a minimum. Easy to handle and carry. Comes standard with 5 feet of 2.5â?? discharge hose & 2.5â?? QST female adapter. Available with a longer hose & different adapter
Sewer Lateral Cleaning Launcher Logiball Sewer Lateral Cleaning Launcher is used to clean laterals from the mainline sewer without the need of a cleanout. It can effectively clean laterals (removing roots, grease and other buildups) as far as 50 feet from the connection. Logiball Lateral Launcher guides your 1/2â?? or 3/8â?³ hose and nozzle into the lateral connection from the mainline sewer. Winched in tandem with the CCTV camera, the 0-90 VDC motor is used to rotate the guiding arm and nozzle into the lateral connection. Typical multiconductor cable required. With the pump turned on, the back jets propel your nozzle and hose into the lateral for cleaning. ALSO AVAILABLE: Lateral Launcher for 6" / 150mm mainline with 0-24 vdc motor Features Stainless steel and aluminium construction Industry standard 4 pin male connector (multiconductor camera cable) 0-90 VDC motor Use tractor controls with multiconductor cable for CW/CCW rotation Replaceable guiding arm Optional control panel for motor rotation of lateral launcher 8 to 18 main assembly For sewer lateral cleaning launchers from 6 mainline contact our sales department
PR11 TEA, a Triethanolamine (TEA) Activator, is a catalyst to be used with PR10 ACLM acrylamide products as an activator for reaction. TDS SDS PR11 TEA Canadian French SDS PR11 TEA Canadian English SDS PR11 TEA US English SDS PR12 APSF is a catalyst to be used with PR10 ACLM acrylamide. It is a white crystalline solid and used as a polymerization initiator. Ammonium persulfate is a powder that is a required grout component. PR12 APSF decomposes over time as it is a strong oxidizing material TDS SDS PR12 APSF Canadian French SDS PR12 APSF Canadian English SDS PR12 APSF US English SDS PR13 SPSF (Sodium Persulfate) is a catalyst to be used with PR10 ACLM acrylamide. It is a white crystalline solid and used as a polymerization initiator. Sodium persulfate is a powder that is a required grout component and can be increased from 5 lbs. (1% by total mix weight of 500 lbs., 60 oz. by volume to a maximum of 15 lbs. (3% by total mix weight of 500 lbs., 180 oz. by volume). PR13 SPSF decomposes over time as it is a strong oxidizing material. TDS SDS PR13 SPSF Canadian French SDS PR13 SPSF Canadian English SDS PR13 SPSF US English SDS PR17 LYTX is a water-based additive to strengthen gel and reduce shrinkage. With acrylamide, replace up to 2 gallons mix water with PR17 LYTX in each tank. Seals leaks in sanitary and storm water mainlines, pipe penetrations, laterals, lift stations and manholes. TDS SDS PR17 LYTX Canadian French SDS PR17 LYTX Canadian English SDS PR17 LYTX US English SDS
Design allows to seal laterals connected to manholes. Injections have been done up to 30 feet. Logiball Man Entry Pipe Lateral Grouter is an inflatable bladder with threaded adapter used to install our standard lateral grouting plugs to seal laterals from a man entry pipe or a manhole. It includes one inflation port for the lateral bladder, one inflation port for the 4-6 bladder, two ports for the chemical grout and one void liquid filled pressure sensor line.
Lateral Test and Seal Packers Logiball 2001L packers are used to test and seal off infiltration in sewer laterals, from the mainline, without any access to cleanouts. The lateral grouting plug is inverted and deployed into the lateral from the mainline packer assembly. The mainline sleeve then expands to create a minimal grout mixing chamber. The grout is pumped and migrates freely along the restricted expansion of the lateral plug and out through existing pipe defects into the surrounding bedding to seals defects, leaving only a thin layer of grout in the lateral. The packers are available with different void pressure monitoring systems; a conventional localized liquid filled sensor (S), recommended for acrylamide and acrylate grouts, an in-wall water chamber sensor (W), recommended for stickier grouts such as urethanes and polyurethanes, or both systems (S+W) for a more versatile use. The 2001L Lateral Packer comes standard with two grout ports and a third port dedicated for the test medium (air or water). 2001L Lateral packers work best with a five-hose system. Lateral Grouting Plugs can be interchanged in a matter of minutes to grout distances up to 30 feet if necessary. Lateral Grouting Plugs are available for 4, 5 or 6 diameter laterals. Flexible housing extensions are needed for lateral grouting plugs 24 or longer. ICGA promotes the proper use of chemical grouting as a safe, economical and effective means to reduce ground water infiltration into sewer collection systems. The 2001L model is available for 6â?³, 8â?³, 9â?³, 10â?³, 12â?³, 15â?³, 18â?³, 21â?³, 24â?³ and 30â?³ mainlines. For larger diameter contact our sales department. For larger diameters, see our Man Entry Lateral Packers for 36â??â?? & up or contact our sales department. Features * As measured on the rubber. Specifications subject to change without notice. Logiball Lateral Packer Approximate Void Volumes. View list of parts for the lateral packers 2001L. (pdf file) A Control Panel is available to operate the lateral packer from the truck.
Logiball Elliptical Mainline test and seal injection packers are custom-made for the exact pipe dimensions and the available access to the storm sewer lines. The two end rubber bladders are covered with a soft rubber sleeve that provides superior seating against rough surfaces. Our elliptical grout packers are equipped with a localized pressure sensor and two injection grouting ports protected by a large, non-clogging adjustable rubber check-valves. Contact us if you need a special configuration. Rentals available, contact our sales department for further information.
2001J Mainline Packers meet the highest standards for testing and sealing joints of mainline sewer pipes with acrylamide, acrylate or urethane gels. Logiball 2001J Mainline Packers meet the highest standards for testing and sealing joints of mainline sewer pipes with acrylamide, acrylate or urethane gels. A thick, reinforced SBR rubber sleeve is bonded to the stainless-steel core and a layer of softer rubber is applied over the seating portion to provide superior seating against rough surfaces. The smooth outer finish reduces the adherence of the grout on the packer. Logiball 2001J Mainline Packers come with two grout ports and a third port dedicated for the test medium (air or water). MAIN FEATURES: Void Pressure Monitoring Systems: Two different void pressure monitoring systems are available to accurately transmit the void test and grouting pressures to a gauge read by the camera or through a pressure transducer. The conventional localized sensor is recommended for acrylamide and acrylate grouts. The in-wall water chamber sensor is recommended for stickier grouts such as urethane gels and polyurethanes. The 2001J Packer can be ordered with both systems or one of the two as needed by customer. Dedicated Test Port: By using a dedicated hose from the truck to the packer for the test medium (air/water), â??Hâ?? blocks are eliminated and the mixing ratio of the two-part grout is kept constant (no flushing of the catalyst when testing). Features Three-Function Adjustable Rubber Check-Valve: They provide added safety against syphoning the tanks and unwanted backflow contamination into the hoses, and provide a good mixing of the two-part chemicals through the fan like stream of the opposed and adjacent ports. The Autotesting Concept: When inflating the 2001J packers, the ends first seal against the pipe wall, while its central portion progressively expands, trapping air and water, and compressing it into the mixing chamber. The pressure in the chamber is transmitted through the improved liquid filled sensor and/or the in-wall water chamber sensor to a gauge or transducer installed on the packer. The operator can tell if a joint is obviously good or not by simply inflating the packer over it. By avoiding time consuming conventional tests, productivity could be increased by as much as 30%. Logiball 2001J Packers approximate void volumes. ICGA promotes the proper use of chemical grouting as a safe, economical and effective mean to reduce ground water.
Reprocessing Plugs Logiball Reprocessing Plugs are field-tested and approved by relining contractors around the world. Ideal for reprocessing the CIPP liners or installing FF liners in pipe sizes ranging from 6â?? to 21â??. These plugs come with a 1/2â?? thick rubber sleeve, reinforced with multiple layers of fabric, and molded on an aluminum core. Steel or stainless-steel construction are also available upon request. FEATURES Rubber sleeves can be factory-replaced. Larger and custom-made configurations are possible. Contact us with your requirements to request a quote.
Controlling the live flows from the surface Logiball multisize high/low flow inflatable sewer plugs allow for optimal flow control during CCTV inspection, pipe reinstatement or sectional lining. By maintaining the sewer flow active, under control and at a reasonable level, work can be performed downstream without completely blocking the flow or requiring bypass pumping. The active flow is controlled from above ground, with the Logiball High Flow/Low Flow Plug. When inflating the plug, the outer bladder expands and seals the host pipe. A separate controlled air line is used to expand the internal sleeve, similar to a pneumatic pinch valve, which reduces the amount of flow going through the center of the plug. The operator can decide how much water flow is allowed to go through the plug by pressurizing or depressurizing the internal seal from the surface, never having to enter the manhole. By releasing the pressure in the internal sleeve, flow is allowed to go through the plug, reducing the back pressure applied on the plug and allowing for a safe plug removal. Features Logiball High Flow/Low Flow Plugs cannot be used for air testing. Air hoses sold separately.
Lightweight inflatable type E plugs Logiball lightweight inflatable type E plugs are your best option for submerged pipes and short sections of pipes. Each plug is factory-tested at the factory at twice the recommended inflation pressure. The light and compact structure of these multisize plugs makes it possible to safely plug small pipes from the surface, using a pipe handle. Perfect for tight, hard-to-reach places, these rubber plugs come with a strong anchoring chain and are made to be used with a standard pipe handle.
Logiball Type D inflatable sewer plug Logiball Type D inflatable sewer plugs are a great tool for by-pass pumping and/or flow diversion when performing manhole and invert rehabilitation. Our Type D pipe plugs feature a double-action bladder: When inflating the plug, the inner bladder forms a tight seal around the by-pass pipe or the pump suction hose, while the outer bladder completely seals against the pipe wall. This â??slip it in and inflate unique feature will save you both time and effort. Logiball Type D plugs are available for pipe sizes ranging from 3â up to 16 in diameter.
Logiball push-type cleanout plugs (type a & b) Logiball push-type inflatable rubber plugs are offered with or without flow-thru for pipe diameters ranging from 3â?³ to 6â?³. These flexible plugs can be inflated and pushed from the cleanout with the optional semi-rigid hose assembly.
Logiplug inflatable sewer plugs Logiplug inflatable sewer plugs can be used in a wide variety of applications such as by-pass pumping, flow control and flow diversion. Logiplug pneumatic plugs can be used for completely stopping water flow when the flow-thru is plugged off. Logiplug rubber plugs are manufactured on lightweight aluminum mandrels. Steel or stainless-steel mandrels are also available upon request. The SBR rubber sleeve is reinforced with two plies of nylon cords for increased durability. Different types of elastomers are available depending on your needs. All Logiplug inflatable sewer plugs are factory tested, at an inflation pressure corresponding to twice the recommended pressure. Each plug is shipped with an inspection certificate and a safety information leaflet.
Used for low pressure line acceptance testing, sewer pipe plugging and flow control. Our pneumatic plugs can be used for pipe sizes ranging from 4â?? to 36â??. Three different models are available: Type A: No flow-thru Type B: Flow-thru by-pass plug with a 2â?? hose (�½â?? hose for the 4-8 model) Type C: Flow-thru by-pass plug with two �½â?? hoses Our sewer plugs are designed to comply with the highest safety standards and include the following features: a two-ply cross-biased reinforced SBR rubber sleeve, anchoring device and end-plate retaining device for maximum strength. To ensure the quality of our products, every inflatable plug is individually tested under severe pressure. Each Logiball Securimax pipe plug is identified by a unique serial number and comes with a test certificate, a leaflet describing the features of the sewer plug and the information on its safe use.
pecifications: Copper wire scrap, (Millberry) 99.99% at a purity of 99.98% min and 99.99% max Copper: 99.9% Carbon: 0.03% Coblet:
We are offering 100% natural sisal fiber material: sisal grade a length: 110cm-130cm moisture: 10%---13% impurity: 0---3% color: natural white or mixed with natural cream details of sisal fiber UG grade: length: 110cm-130cm with a tolerance of 20%. Moisture: 10%---13% impurity: 0---3% classification per grade: type 1 - colour whitishsoft cream, well brushed, humidity maximum 14% without knots. Type 2 - colour creamyellowish, well brushed, humidity maximum 14% without knots. Type 3 - colour creamyellowish, well brushed, humidity maximum 14%, without knots. Refugos (reject) - colour brownishgreen, humidity maximum 14%, presence of knots and high percentage of impurities. Bucha (tow) - colour yellowishbrownish, humidity maximum 14%, presence of knots and a very high level of dust. trade terms:
Sudhanafluid pneumatic valve series: butterfly valve The butterfly plate of the butterfly valve is installed in the diameter direction of the pipe. In the cylindrical channel of the butterfly valve body, the disc shaped butterfly plate rotates around the axis with a rotation angle of 0 �°~90 �°. When the rotation angle reaches 90 �°, the valve is fully open. The butterfly valve is simple in structure, small in volume and light in weight, and only consists of a few parts. Moreover, the valve can be quickly opened and closed only by rotating 90 �°, which is simple to operate. At the same time, the valve has good fluid control characteristics. When the butterfly valve is in the fully open position, the thickness of the butterfly plate is the resistance when the medium flows through the valve body, so the pressure drop generated by the valve is very small, so it has good flow control characteristics. The butterfly valve has two sealing types: elastic seal and metal seal. For elastic sealing valves, the sealing ring can be embedded on the valve body or attached to the periphery of the butterfly plate. The valve with metal seal is generally longer than the valve with elastic seal, but it is difficult to achieve complete sealing. The metal seal can adapt to higher working temperature, while the elastic seal has the defect of being limited by temperature. If the butterfly valve is required to be used for flow control, the main thing is to correctly select the size and type of the valve. The structure principle of butterfly valve is especially suitable for making large diameter valves. Butterfly valves are not only widely used in petroleum, gas, chemical industry, water treatment and other general industries, but also used in the cooling water system of thermal power plants. There are two kinds of butterfly valves commonly used: wafer type butterfly valve and flange type butterfly valve. Wafer type butterfly valve uses stud bolts to connect the valve between two pipe flanges. Flange type butterfly valve has flanges on the valve, and bolts are used to connect the flanges on both ends of the valve to the pipe flanges.
â??Product Name: Pneumatic flange ball valve Valve Type: Ball valve Design Standard: GB,ANSI,DIN,JIS Working Pressure: 0~1.6Mpa Medium: water, gas, oil, acid, alkali Medium Temperature: -20�ºC~+180�ºC Port Size: DN15-DN200 Connection: flange Structure: floating full port Body Material: cast steel, stainless steel Seat Material: PTFE Application: water system, waster water system, oil& gas industry Driving Way: Pneumatic actuated Actuator Material: Aluminium Alloy Actuator Model: AT52D-AT115D Action: double-acting Rotary Angle: 90�° Air Pressure: 4~8bar Cylinder Size: 52-115 mm Output Torque : 20-344 NM Working Temperature: -20C~+80C Air Access: G1/4" Warranty: 12 months
