Complete Automatic Aluminum Foil Container Making Machine Line Model: SEAC-55AS Units: Automatic Feeder+Automatic55Ton Press+Cavities Mould+Auto Stacker+Scrap Sucker & Auto Presser. It fit for all common size Aluminum Foil Container production requested. The Big capacity could to cover big range of size products. Lower power requested than other old model machines. Specification: 1. Raw material: Aluminum foil; Thickness: 0.030mm ~0.250mm; Alloy: 8011, 8006, 3003, 3005; Temper O to H24; 2. Good Japan's Inverter, PLC and 10inch Touch Screen control system; 3. Max. Width of Aluminum foil: 600mm; 4. Max. Diameter of Aluminum foil: 700mm; 5. Core diameter of Aluminum foil: 76mm(152mm as Optional ); 6. Working speed: 40-75 times/min; 7. Total Power: 13kw; 8. Compressed air needed: 0.5- 0.8 Mpa, 0.2m3/min; 9. Install dimension: 6100*2600*3200mm; Technical Data: Max. Mould Size:L700*800*420mm; Slide block stroke: 120-200mm (Standard: 180mm); Automatic mould adjust unit: 0.5kw; Work plate dimension: 700*950mm; Mould handle hole dimension: 50*60mm(Diameter*Depth); Power: 3P, 380/220V, 50/60Hz; Net weight: 6000kg. SEAC-55AS is two cavities capacity for Aluminum foil container production now, it have instead of the old 40Ton model, as it is more big capacity to cover container size! Complete automatic level upgrade your factory capacity, lead your company be higher level competition and situation.
Complete Automatic Aluminum Foil Container Making Machine Line Model: SEAC-63A-4 : Max. Mould Lenght 1150mm Units: Automatic Feeder+Automatic 63Ton Press+Cavities Mould+Auto Stacker+Scrap Sucker& Presser. It fit for all common size Aluminum Foil Container production requested. The Big capacity could to cover big range of size products. Lower power requested than other old model machines. Specification: 1. Raw material: Aluminum foil; Thickness: 0.030mm~0.250mm; Alloy: 8011, 8006, 3003, 3005 etc.; 2. Japan Inverter, PLC and 10inch touch screen control system; 3. Max. Width of Aluminum foil: 880mm; 4. Max. Diameter of Aluminum foil: 1000mm; 5. Core diameter of Aluminum foil: 76/152mm; 6. Working speed: 40-75 times/min; 7. Total Power: 11kw+2kw+2kw+1kw; 4Motor 8. Compressed air needed: 0.5- 0.8 Mpa, 0.2m3/min; 9. Install dimension: 7100*2600*3500mm; Technical Data: Max. Mould Size: 1100*900*450mm; Slide block stroke: 180-260mm; Slide block dimension: 380*145mm; Automatic mould height adjust unit: 0.5kw; Work plate dimension: 1100*200*300mm, separated two sets with Balls; Tension: complete automatic adjust; Feeding System: Servo Motor, higher precision and more power; Auto Stacker: SMC lift for stacking system, top quality; Power: 4P, 380V or 220V, 50Hz /60Hz; Net weight: 9,500kg.
Technical Parameters Travel of X and Y Axes: 800x1200 mm; Maximum cutting thickness/ Maximum height of the part: 700 mm; Maximum Work piece weight: 1000 kg; Wire diameter: Standard 0.18 mm mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 985x1580 mm; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " . Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; No. of axes: 4 axes (X,Y,U,V) Maximum cutting speed: 160 square mm/min; Numerical Control System: X8 ; Motor power: 2.5 KW; Maximum processing current: 7 A; Maximum power consumption: less than 1 KVA; Minimum feed increment: 0.001 mm; Adjustable range of pulse width: 15-150 �¼s; Approx. Machine size (LxWxH): 2600x2400x1800 mm; Approx. Machine weight: 4500 kg; Approx. Machine control cabinet size: 670x630x1800 mm; Approx. Machine control cabinet weight: 200 kg; Operating system/CNC system/Software drawing system: X8 system is a total integrated system that includes CNC system, Operating system and Software drawing system. ; Menu language: Chinese and English ; The units of measurement does the system use: Metric ; Data port: USB port, RS 232C port, Ethernet port ; Operating room temperature: Normally is 5-40 , we suggest 10-20 â??. ;
Technical Parameters : Travel of X and Y Axes: 500x630 mm; Maximum cutting thickness/ Maximum height of the part: 600 mm; Maximum Work piece weight: 700 kg; Wire diameter: Standard 0.18 mm; Optional: 0.12-0.2 mm; Cutting Taper: 6 degrees (Plus and Minus 3 degrees)/ 80 mm Degree/mm; Work Table Size (LxWxH): 600x860x600 mm; Surface Roughness(Ra): "Cutting Condition: Straight line cutting and Height less than 40mm. One-time wire cutting, Ra: less than 2.3 um; Two-time wire cutting at same position, Ra: less than 1.6um; Three-time wire cutting at same position, Ra: less than 1.0 um. " . Machining precision/Processing precision: "0.01. Multi time wire cuttings: Material=Cr12 and Height=40mm. Precision less than 0.006mm" mm; Positioning accuracy of X/Y axis: 0.03 (plus or minus 0.015) mm; No. of axes: 4 axes (X,Y,U,V) Maximum cutting speed: 150 square mm/min; Numerical Control System: X8 ; Motor power: 2.5 KW; Maximum processing current: 7 A; Maximum power consumption: less than 1 KVA; Minimum feed increment: 0.001 mm; Adjustable range of pulse width: 15-150; Approx. Machine size (LxWxH): 2000x1950x1750 mm; Approx. Machine weight: 2540 kg; Approx. Machine control cabinet size: 700x670x1100 mm; Approx. Machine control cabinet weight: 80 kg; Operating system/CNC system/Software drawing system: X8 system is a total integrated system that includes CNC system, Operating system and Software drawing system. ; Menu language: Chinese and English ; The units of measurement does the system use: Metric ; Data port: USB port, RS 232C port, Ethernet port ; Operating room temperature: Normally is 5-40 , we suggest 10-20 ;
Very Profitable Aluminum Foil Container Production Line Complete Automatic Aluminium Foil Container Making Machine Model: SEAC-80/130AS (Four Cavities or Five Cavities Capacity !) Units: Automatic Feeder+Automatic 80Ton H Type Press+Cavities Mould+Auto Stacker+Scrap Sucker & Auto Presser. It fit for all common size Aluminum Foil Container production requested. The Big capacity could to cover big range of size products. Lower power requested than other old model machines. Specification: 1.Raw material: Aluminum foil; Thickness: 0.030mm ~0.280mm; Alloy: 8011,8006,3003,3005; Temper O to H24; 2.Good Japan's Inverter, PLC and 10inch Touch Screen control system; 3.Max. width of Aluminum foil: 1220mm; 4.Max. diameter of Aluminum foil: 1000mm; 5.Core diameter of Aluminum foil: 76mm(152mm as Optional ); 6.Working speed: 40-75 times/min; 7.Total Power: 14kw+2kw+2.5kw+3kw; 8.Compressed air needed: 0.5- 0.8 Mpa, 0.4m3/min; 9.Install dimension: 7100*2600*3600mm; Technical Data: Max.mould size: 1480*1000*500mm; Slide block stroke:150-260mm ; (Offer Stroke adjustable system as option!) Automatic mould adjust unit: 0.5kw; Work plate dimension: 1500*1000mm; Mould handle hole dimension: 80*80mm(Diameter*Depth); Power: 4P, 380/220V, 50/60Hz; Net weight: 13,000kg. SEAC-80AS is the four cavities or five cavities capacity model production line for AFC. Complete automatic level upgrade your factory capacity, lead your company be higher level competition and situation.
Rebar Coupler The splicing couplers model is divided into 9 categories according to the Rebar Coupler. (Unit: mm) 1).The parameter of couplers Size(mm) O D�±0.5ï¼?mmï¼? Threadï¼?mmï¼? L�±0.5 (mm) Pitch Rib peeling coupler weight/pc (kg) Thread Angle �¦16 25 M16.5 40 2.0 0.111 60 Degree �¦18 28 M18.5 45 2.5 0.136 �¦20 31 M20.5 50 0.175 �¦22 33 M22.5 55 0.203 �¦25 37 M25.5 60 0.266 �¦28 41 M28.6 70 3.0 0.375 2).The Characteristics of the Usage Mode usage occasion Standard Model used in the occasion for connecting the steel bar in normal situation Different Diameter Model used for connecting the steel bar in different diameters Flared Model used for the steel bar which was hard to match Positive And Negative Screw Thread Model Used in the occasion when the steel bar in the two sides both can not be turned but the lengths can be adjusted. Locking Nut Model Used when the steel bar can not be turned, then it turns the splicing coupler to join the steel bar and then lock the splicing coupler with the locking nut. 3).The material of the splicing coupler The material of the splicing coupler is constructional quality steel of No.45 steel.
Meets the requirements of: Cummins CES 20081 MB 228.31/228.51 MAN M3677/3477/3575/3271-1 Volvo VDS-4 RVI RLD-3/RLD-2 JASO DH-2 MACK EO-N Premium Plus MACK EO-O Premium Plus CAT ECF-3 Detroit Diesel 93K218 MTU Oil Category 3.1/2.1 Deutz DQC-IV-10 LA Scania LA Scania LDF-4 Voith Class B / MB 235.28 Specifications: API CJ-4 ACEA 2016 E4/E6/E7/E9 TECHNOL POWER LD 10W-40 is a synthetic technology engine oil that has been formulated to satisfy the most stringent requirements of on-road trucks with heavy duty diesel engines. It is also suitable for use in most gasoline engines. This engine oil protects diesel engines equipped with post-treatment systems, such as diesel particulate filters (DPF), thanks to its specific Low SAPS technology (low content in Sulphated Ash, Phosphorus, and Sulphur). This engine oil provides outstanding resistance to oxidation and corrosion, contains detergents and dispersants that keep the engine clean and possesses antirust, and antiwear properties. Its high viscosity index and thermal stability ensure proper lubrication of moving components of the engine under most severe operating conditions. With its extended drain intervals, use of this engine oil helps reduce maintenance costs. It is recommended for use in Euro 4 and Euro 5 engines of most manufacturers.
Soybean Seed 1. Introduction: Soybean seeds, scientifically known as Glycine max, are a valuable leguminous crop renowned for their high protein and oil content. A versatile commodity, soybean seeds find application in various industries, including food processing, animal feed production, and oil extraction. This product information guide provides key details about soybean seeds, covering their characteristics, nutritional value, common uses, and storage considerations. 2. Characteristics: Shape and Size: Soybean seeds are typically small, oval-shaped legumes with a length ranging from 5 to 11 mm. Color: The color of soybean seeds can vary, including shades of yellow, brown, or black, depending on the variety. Texture: The seed coat is smooth, and the seeds have a firm yet easily crushable texture. 3. Nutritional Composition: Protein Content: Soybean seeds are prized for their high protein content, ranging from 35% to 40%. This makes them a valuable source of plant-based protein. Oil Content: Soybeans contain approximately 18% to 20% oil, primarily consisting of polyunsaturated fats. Carbohydrates: The carbohydrate content is moderate, providing energy and dietary fiber. Vitamins and Minerals: Soybeans are rich in vitamins (B-complex) and minerals (iron, calcium, magnesium), contributing to their nutritional profile. 4. Common Uses: Edible Oil Production: Soybean oil is extracted from the seeds and widely used in cooking and food preparation. Animal Feed: Soybean meal, a byproduct of oil extraction, is a valuable protein source in livestock and poultry feed. Food Products: Soybeans are processed into various food products, including tofu, soy milk, soy sauce, and textured vegetable protein (TVP). Industrial Applications: Soybean oil is used in non-food applications such as biodiesel production and as a base for industrial lubricants. 5. Storage Considerations: Moisture Control: Soybean seeds should be stored in a cool, dry place to prevent moisture absorption and reduce the risk of mold growth. Airtight Containers: Packaging should be airtight to maintain freshness and prevent the seeds from becoming rancid due to exposure to air. Temperature: Storage temperatures should ideally be below 25�°C to preserve the quality of the seeds.
Xiongcai Technology XCA105 Motor Speed Controller For Fuel Pump 1. Voltage DC16~36V 2. Rated Currentï¼?10A 3. Working Tempï¼?-40ï½?85â?? 4. Working Humidityï¼?95% 5. Size: 87*84*15mm 6. Protectionï¼?under voltage, over voltage, low temperature, over temperature, plugging, reverse connection, short circuit 7. PWM speed regulation With 12-year experience, Xiongcai Technology, a pioneering company in specialized field of motor control. Founded by experienced engineer, started the innovative journey in motor control. Established in 2011, Xiongcai Technology emerged as a pioneer driven by a commitment to drive motor more efficienctly and put your devices to their limit. We are one of the few engineering companies providing a full service from design to supply of product, which means we design, analyze, test and supply finished products. Xiongcai released a motor controller XCA105, engineered for automotive fuel pump. With pwoer system of 8A current, DC8-18V, push the performance to its limit. Minus 40 degree to 125 degree working temperature enables the motor controller work at any weather condition. The dimension is 37*34*8mm, compact design makes installation more flexible. You don't need to make a big space for this component. Safety is vital to automotive application. It's small, but it is engineered to function without sacrificing safety. The protection measures include under voltage, over voltage, over current low temperature, over temperature, plugging, reverse connection and short circuit protection. safety is always the first priority. Xiongcai motor controllers have been applying in top brands in automotive industries, such as Jingyi Group, Risun, FAW Group, FAWDE, Feilong Auto (FLACC), Keshen, Unicent and more. We can put your RC car in extreme. Contact Shenzhen Xiongcai Technology Co., Ltd for detail.
Loc Nam Import Export Company Limited (Loc Nam Imex Co., LTD) is an exporter specialized in providing bulk quantities of high quality agricultural products in Vietnam. Established since 2012, with more than 10 years building and developing, we now have more than 20 items in our catalogue including Black and white pepper, cashew nuts, coffee and spices. Our main export markets are Asia and Europe. We pride ourselves on our market and product knowledge, high quality management and customer services including processing facilities which meet the international standards of ISO 22000, ISO 9001, HACCP. About cashew nuts, we product a wide rank of products including: Whole cashew nuts: W180, W210, W240, W320 Broken cashew nuts: WS, LP, SP Roasted cashew nuts: salted/unsalted, flavored Specifications of cashew nuts W320: - Color: White / Pale ivory / Light ash - Condition: Whole Cashew Nuts Kernel - Grade: ww320 (AFI standard) - Nut Count/pound: 300-320 nuts - Nut Count/kg: 660-706 nuts - Moisture: Max 5% (as customer request) - Broken: Max 10% (as customer request) - Lower Size Grade: Max 10% (as per customer request) - Defects: Max 8% (as customer request) - Origin: Vietnam - Quality inspection: Cafe Control / SGS / your QC inspection before shipment. - Packing: In 2 x 25 lbs (11.34 kgs) vacuumed tins in cartons or In 1 x 50 lbs (22.68 kgs) vacuum flexy pouches in cartons or ., 700 cartons in 20 Full Load Containers and 1400 cartons in 40 Full Load Containers or as specific customer requirement.
The Manufacturers and Suppliers of the exceptionally duplex steel flanges made their things for the client in different shapes and sizes as per the client's interest. Profound Steel Community is the producer, stockist, and supplier of the entire thing, including this. They supply, generally speaking, and convey the thing by staying aware of the stunning quality and cost as well. According to their properties and components, Extremely Duplex Steel Flanges are considered the best in the series of steel flanges. A few things like copper, zinc, and chromium are open in the Extremely Decision, which makes it austenitic solidified steel. An enormous piece of the undertaking uses phenomenally strong Duplex steel since when these parts come in contact, they produce high strength. Specification of Super Duplex Stainless Steel S32750/S32760 Flanges Super Duplex Stainless Steel Flanges Specification : ASTM A182 / ASME SA182 Dimension Standard : ANSI/ASME B16.5, B 16.47 Series A & B, B16.48, BS4504, BS 10, EN-1092, DIN, etc. Standard : ANSI Flanges, ASME Flanges, BS Flanges, DIN Flanges, EN Flanges, etc. Size : 1/2" (15 NB) to 48" (1200NB) Class / Pressure : 150#, 300#, 600#, 900#, 1500#, 2500#, PN6, PN10, PN16, PN25, PN40, PN64 etc. Flange Face Type : Flate Face (FF), Raised Face (RF), Ring Type Joint (RTJ) DIN Flanges : DIN 2527, 2566, 2573, 2576, 2641,2642, 2655, 2656, 2627, 2628, 2629, 2631, 2632, 2633, 2634, 2635, 2636, 2637,2638, 2673. JIS Flanges : JIS B2220 5K, JIS B2220 10K, JIS B2220 16K, JIS B2220 20K BS Flanges : BS4504 PN 6, BS 4504 PN 10, BS4504 PN 16, BS4504 PN 25, BS4504 PN 40, BS 4504 PN 64, BS 4504 PN 100, BS 4504 PN 160, BS 4504 PN 250, BS 10, BS Table D, BS Table E, BS Table F, BS Table H.
Logiscell+ activated oakum kit is composed of dry oakum soaked into a hydrophilic polymer solution to seal manholes and sewer lines. When wet and caulked in a joint or crack, the resin will foam to form a flexible and tight joint to stop groundwater infiltration. It reacts with water and becomes a watertight rubberlike non-toxic composite. The oakum cord gives strength and density to the composite and makes the application of the resin easier, especially when gushers are present. The kit includes a 1.7-liter bottle of Logiscell+ (hydrophilic resin) and one bag containing a �± 0.6 lbs of dry oakum. 18 liter pails also available. ACTIVATED OAKUM TECHNIQUE: 1) When mixed with water the resin forms a spongy foam which could absorb up to 12 times its volume of water. A non-controlled expansion could create a low-density foam, which is less watertight and resistant. If the oakum is well-inserted and uniform within the area, a good density and expansion is obtained to fill the void and stop leaks. 2) After approximately 40 seconds, the reinforced foam resin starts to react to form a rubbery gasket which becomes hard, watertight and adheres to the surface. Note: If there is a significant flow within the joint or crack, it is preferable to soak the oakum and let it partially react before the insertion in the crack or joint. By holding it tightly within the crack or joint, the resin will not be washed away by the gushing water. This technique can also be used for underwater applications. CAUTION: Prevent any contact with eyes and skin. Always wear PPE (gloves, goggles, disposable suit and mask or respirator depending on the environment). Certain people may be affected by the vapours during the reaction of the resin. To prevent irritation of throat or eyes always ventilate the working area. If it is impossible to ventilate use a mask with appropriate cartridge. Wash hands and face thoroughly after installation.
Model POE-S2004FB Ports 4 10/100Mbps POE + 2 10/100Mbps Uplink Power Input AC 100-240V, 50/60Hz, 1.0A Max. Power Output DC 48-57V, 80W (Rated), Full Load Max. 65W (Net Output) Max. 60W for 1st PoE port Max. 30W for 2nd~4th PoE port Data Exchange 10/100Mbps (Gigabit is optional and available), Store and Forward Bandwidth/MAC 1.6Gbps, 1K Package Forwarding/Buffer 1.15Mpps, 768K Power/Data Assignment Power: pin 1,2 + pin 3,6 - ; Data: pin 1,2,3,6 Ambient Environment Operating temperature: -10~55 Storing temperature: - 40~75 Operating Humidity: 5%~90% RH, No condensing Storing Humidity: 5%~95% RH, No condensing Network Protocolï¼? IEEE 802.3 Ethernet media access control protocol IEEE 802.3i 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3af/at/PoE++ Power over Ethernet cable pairs or device IEEE 802.3x Flow control IEEE802.1q VLAN Network bridge operation Data Speed Ethernet 10Mbps half-duplex, 20Mbps full-duplex Fast Ethernet 100Mbpshalf-duplex, 200Mbps full-duplex Network Medium 10Base-T: Pair 2 Category 3,4,5(Cat3,4,5) UTP/STP(â?¤250m) 100Base-TX: Pair 2 Category 5(Cat5) or better UTP/STP(â? 150m) System Mode Standard Free communication VLAN Port Isolation 250m Supper long-distance transmission Lightning Protection 3KV 8/20us Certificate CE, FCC, RoHS Warranty 1~2 years Size/Weight PoE Switch Size: 190mm*130mm*33mm (L*W*H) Packing Box Size: 310mm*210mm*60mm (L*W*H) Net Weight: 0.9kg, Gross Weight:1.1kg
Sidewall Conveyor Belt, Sidewall Rubber Conveyor Belt, Steep Angle Sidewall Conveyor Belt Manufacturer 1. Applications There are no cleats on sidewall conveyor belt which is suitable for horizontal, short-distance transportation. (no cleats at the moment) 2. Structure It consists of two parts: -Base belt: high tensile strength, high abrasion resistant , good transverse stiffness and good lengthways flexibility. -Sidewall: high tensile strength, hot vulcanization with base belt, height up to 40-80mm, fabric reinforcement built in sidewall. 3. Sidewall conveyor belt specification Belt width (mm) Sidewall height (mm) Cleat height (mm) Effective belt width (mm) 400 60 - 80 70 100 90 120 100 500 60 250 80 70 100 90 120 110 160 140 650 60 250, 300, 350 80 70 100 90 120 110 160 140 200 180 800 60 350, 410, 460 80 70 100 90 120 110 160 140 200 180 240 220 1000 60 460, 550, 640, 690, 80 70 100 90 120 110 160 140 200 180 240 220 300 270 1200 60 460, 550, 640, 690 80 70 100 90 120 110 160 140 200 180 240 220 300 270 Huayue started business by producing rubber belts since 1982. It has been one of Solid Woven Convey or Belts manufacturers and is the major factory of fabric conveyor belt and Steel Cord Conveyor Belt in China.
https:**powertoolsequip*com*products*-Agri%252dFab-Hard%252dTop-Chip%252dN%252dVac-Tow%252dBehind-Lawn-Vacuum*html https://powertoolsequip.com/products/-Agri%252dFab-Hard%252dTop-Chip%252dN%252dVac-Tow%252dBehind-Lawn-Vacuum.html AGRI-FAB HARD-TOP CHIP-N-VAC TOW-BEHIND LAWN VACUUM Price:$886.35 SKU:45-0540 Brand:Agri-Fab Condition:New Weight:1.00 LBS Shipping:Calculated at checkout Product Description Features 208cc Briggs & Stratton Intek Engine Dependable, powerful performance Creates 80 mph suction power Enough power for leaves, pine needles and grass clippings Safety shutoff prevents accidental engine startups Large 26 Bushel/32 Cu Ft Capacity Holds more yard debris - meaning fewer stops Hopper tilts back for easy dumping of yard debris Hard Top Collector Vented to keep dust out of the engine, prevents wear Steel, Side Chipper Hopper Chips branches up to 2" in diameter Converts yard debris into useful mulch Versatile Design Fits over 40 different tractor decks up to 54" wide Templates included (only fits right-side discharge mowers) Additional hose kit (#65640) needed for zero-turn mowers Optional #45-0253 Hose Kit (sold separately) Vacuum debris around shrubs, on patios and under decks Some Assembly Required - Shipped 75% Assembled Specifications Engine Engine Brand Briggs & Stratton Starting System Recoil Start Engine Cycle 4-Cycle CC 208 CCs Fuel Tank Size 1 Gallon Consumer Engine Warranty 1 Year Feed Chute Wood Diameter 2 Inches Feed Type Gravity Number of Blades 2 Blades Replaceable Blades Yes Discharge Chute Bag No Discharge Chute Material Plastic Vacuum Removable Hose No Towing Towable Yes D.O.T. Lights No Fenders Yes Hitch Type ATV/Lawn Mower Hitch Accessories Rear Bagger No Wheels Tire Type Pneumatic Wheels Overview Assembly Required Yes Weight 365 Pounds Product Length 96 Inches Product Width 33 Inches Product Height 62 Inches Consumer Warranty 3 Years Commercial Warranty 90 Days UPC 00052613104705
Features for the DuroMax XP11500EH Generator Plenty of Power With 11,500 starting watts and 9,000 running watts, this unit can handle heavy loads, from lights and a refrigerator to a home air conditioner and high amperage power tools. Dual Fuel Technology This generator runs on gasoline or propane, giving you the freedom and flexibility of fuel choice. Powerful Engine â?? The DuroMax 457cc OHV engine is a workhorse that provides plenty of power to handle multiple jobs, from powering high voltage appliances to heavy duty power tools. Low Oil Shutoff â?? Protects your investment by automatically shutting the generator off when it senses that the oil is low. Fully Featured Power Panel â?? The power panel includes a wide selection of outlets for maximum compatibility in your applications including: 2 120V household GFCI outlets, 1 120V 30A twist lock outlet, 1 240V 30A outlet, and one 240V 50A outlet. The panel also includes a digital voltmeter. Complies with Emissions Standards â?? All DuroMax generators are both approved by the EPA (Environmental Protection Agency) and CARB (California Air Resources Board) and follow strict guidelines to ensure our generators are as environmentally friendly as possible. Included Oil Funnel Spark Plug Wrench Tool Set Wheel & Handle Kit Propane Regulator Ownerâ??s Manual Specifications (POWER) GASOLINE Peak Watts: 11,500 Running Watts: 9,000 Peak Amps @ 120V: 95.83 Running Amps @ 120V: 75.00 Peak Amps @ 240V: 47.92 Running Amps @ 240V: 37.50 PROPANE Peak Watts: 10,925 Running Watts: 8,550 Peak Amps @ 120V: 91.04 Running Amps @ 120V: 71.25 Peak Amps @ 240V: 45.52 Running Amps @ 240V: 35.63 PRODUCT SPECIFICATIONS Amperage: 75.00A / 37.50A Voltage: 120V / 240VAC Frequency: 60 Hz Engine Size: 457 cc Engine Type: 4-Cycle Air-Cooled Spark-Ignition Engine Speed: 3600 rpm Fuel Type: Gasoline / Propane Fuel Tank Capacity (Gasoline): 8.3 gal Suggested Tank Size (Propane): 40 lbs. Runtime (Gasoline) at 50% Load: 8 hrs. Runtime (Propane) at 50% Load: 6 hrs. Start Type: Electric / Recoil Volume Level: 72 dB EPA Certified: Yes CARB Certified: Yes Product Dimensions: 29" L x 30" W x 26" H Product Weight: 224 lbs.
Features for the California Air Tools 10020DSPC Air Compressor mowerequip....com The CALIFORNIA AIR TOOLS 10020DSPC Ultra Quiet & Oil-Free Air Compressor is designed to be one of the quietest 2.0 horsepower air compressors in the industry having only 58 decibels of sound. Designed for many applications including Dental Offices and Milling Machines. The powerful 2.0 HP motor operates at only 1680 RPM creating less noise, vibration and creating less wear. The Oil-Free Dual Piston Pump System is engineered for longevity, high performance, and durability. The SP-9421 Motor/Pump is tested for a minimum pump life of 3000 hours before service. 30% more life before repair Large 10.0-gallon steel air tank. The Air Dyer is specially designed to remove the water vapor from the air to protect sensitive tools and machinery. To dry the air from the air compressor an Aftercooler and Dryer are utilized. The aftercooler is a heat exchanger for cooling the discharge air from the air compressor. The water vapor from the compressed air is condensed into liquid form and pushed into the Air Dyer. The sturdy large steel cabinet on caster wheels makes it easier to move and reduces the noise level. The interior of the cabinet is lined with acoustic sound proofing foam insulation to reduce the air compressor's noise and vibration. The two latching door handles allows for easy access to the air compressor.'' The two exhaust fans are designed to remove the air from the cabinet for a cooler running air compressor. This air compressor is ideal for anyone working inside (office, shop, store, warehouse, or home) where noise is a major issue. Activated Alumina is used in air repurification (due to its high water and carbon dioxide adsorption capacity) and adsorption of sulfur compounds. Commercial Use Assembled in USA with global components Air Dyer Includes Activated Alumina desiccant with a 4000-hour life. Oil-Free Pump Cleaner air for better tool operation. Less maintenance and Costs. One 1/4 Industrial female quick connector Two Pressure control gauges Thermal Overload Protector Specifications Sound (Ultra Quiet): 58 decibels Maximum Pressure: 130 PSI Kick On Pressure: 100 PSI Kick Off Pressure: 130 PSI Volts: 110v Hertz: 60 Hz Low Amp Draw: 14.0 Amps Tank fill rate from empty to full: 130 Seconds Recovery time from 100 PSI to 130 PSI: 40 Seconds Duty Cycle: 70/30 Maximum Run Time: 30-60 min. (Depending PSI & CFM) Dimensions: L (26") x W (30") x H (39.5") Weight: 221 pounds Aftercooler: Condenser Horsepower: 2.0HP (Rated/Running) Air Flow Per Minute: 6.40 CFM @ 40 PSI Air Flow Per Minute: 5.30 CFM @ 90 PSI
Welding Machine, Tig Welder, Welding Equipment, Arc/MMA/ZX7 Welding Machine, Inverter Welding, Dc Welder, Welding, Welder, Arc Welder, Power Tool, Welding Solder, Tig Welding, Tig Welder, Mig Welding, Ac Welding Machine, Plasma Cutter, Cutting Machine, Plasma Cutting Machine, welding helmet and power tools. Features: 1.Intelligent interface conversion 2.Adopt IGBT single tube/single module to ensure reliability 3.Unique switching power supply,wide application range of power supply 4.SMT chip design,ensure the duty cycle 5.32-bit microcomputer chip processor,real-time current display 6.Advanced high-efficiency inverter technology,30khz,high working frequency 7.Usable for generator, suitable for field operation 8.Automatically save the parameters of the last operation 9.Overheat,overvoltage,undervoltage protection to prevent machine damage 10.Suitable for acid,alkaline,high strength electrode and other welding electrode 11.Coloered LCD display,easy to use Model TIG200 TIG250 TIG250PFC ACDC TIG300 ACDC TIG400DC TIG500DC TIG500 ACDC Rated Input Voltage(V) 1~230 3~400 95-275 3~400 3~400 3~400 3~400 Input Frequency(Hz) 50/60 50/60 50/60 50/60 50/60 50/60 50/60 Rated Input Current(A) 33 30 25 22 31.5 43 43 No-load Voltage(V) 68 68 68 70 70 70 70 Power Factor 0.65 0.7 0.99 0.7 0.7 0.7 0.7 Output Current Range (A) 5-200 5-250 10-250 5-300 5-400 5-500 10-500 Duty Cycle(%)40C�° 25% 60% 25% 60% 60% 60% 60% Efficiency(%) 80 80 80 80 80 80 80 Insulation Class H H H H H H H Protection Class Ip23 Ip23 Ip23 Ip23 Ip23 Ip23 Ip23 Weight(Kg) 8.5 12 13 22 22 28 40 Dimension(mm) 410x180x330 410X180X330 410X180X330 410X220X405 650X285X510 650X285X510 680X285X510 WHY CHOOSE US? Q1.Are you manufacturer or trading company? A.We are the only manufacturer of electrical products. Welcome to visit our factory at any time. Q 2. what's the payment term? A. We accept T/T etc. Q 3. What's the delivery time ? A. Normal model 1-3days,because we have ability to do the stock. For big order,it takes about 15-20days. Q 4. What is the standard of package? A. Export standard package or special package according to customer requirement . Q 5. what kind of product quality your factory offer? A. We are professional factory and we offer top quality to help client to get more market. Q 6. Do you accept OEM business? A. We do OEM . Q 7.Which market do you already sell? A.We already ship to Europe,America, Oceania etc. Q8. what kind of certificate you have ? A.We have CE, GS, ROHS, EMC etc.
Product Description 200A/250A/300A/400A/500A/630A DC TIG Welder/MMA Welder/DC Welder/TIG Welding Machine Lift TIG/Hf TIGWelding Machine, Tig Welder, Welding Equipment, Arc/MMA/ZX7 Welding Machine, Inverter Welding, Dc Welder, Welding, Welder, Arc Welder, Power Tool, Welding Solder, Tig Welding, Tig Welder, Mig Welding, Ac Welding Machine, Plasma Cutter, Cutting Machine, Plasma Cutting Machine, welding helmet and power tools. Features: 1.Intelligent interface conversion 2.Adopt IGBT single tube to ensure reliability 3.Unique switching power supply,wide application range of power supply 4.SMT chip design,ensure the duty cycle 5.32-bit microcomputer chip processor,real-time current display 6.Advanced high-efficiency inverter technology,35khz,high working frequency 7.Usable for generator, suitable for field operation 8.Automatically save the parameters of the last operation 9.Overheat,over voltage,under voltage protection to prevent machine damage 10.Colored LCD display,easy to use WHY CHOOSE US? Q1.Are you manufacturer or trading company? A.We are the only manufacturer of electrical products.Welcome to visit our factory at any time. Q 2. what's the payment term? A. We accept T/T etc. Q 3. What's the delivery time ? A. Normal model 1-3days,because we have ability to do the stock.For big order,it takes about 15-20days. Q 4. What is the standard of package? A. Export standard package or special package according to customer requirement. Q 5. what kind of product quality your factory offer? A. We are professional factory and we offer top quality to help client to get more market. Q 6. Do you accept OEM business? A. We do OEM . Q 7.Which market do you already sell? A.We already ship to Europe,America, Oceania etc. Q8. what kind of certificate you have ? A.We have CE, GS, ROHS, EMC etc. Model CUT-30 CUT-45PFC CUT-60CNC CUT-65CNC CUT-80CNC CUT-100CNC CUT-120CNC Rated Input Voltage(V) 1~230 95~275 3~400 3~400 3~400 3~400 3~400 Input Frequency(Hz) 50/60 50/60 50/60 50/60 50/60 50/60 50/60 Rated Input Current(A) 40 29 15.7 18 30 33 43 No-load Voltage(V) 320 265 400 400 415 415 415 Power Factor 0.65 0.99 0.7 0.7 0.7 0.7 0.7 Output Current Range (A) 10-30 10-45 15-60 15-65 15-80 15-100 15-120 Duty Cycle(%)40C�° 25% 25% 60% 60% 60% 60% 80% Efficiency(%) 80 80 80 80 80 80 80 Insulation Class H H H H H H H Protection Class Ip23 Ip23 Ip23 Ip23 Ip23 Ip23 Ip23 Weight(Kg) 7 8.5 18 20 25 30 32 Dimension(mm) 360x180x330 410X180X330 410X220X405 410X220X405 450X220X405 450X220X405 550X260X490
Product Description 200A/250A/300A/400A/500A/630A DC TIG Welder/MMA Welder/DC Welder/TIG Welding Machine Lift TIG/Hf TIGWelding Machine, Tig Welder, Welding Equipment, Arc/MMA/ZX7 Welding Machine, Inverter Welding, Dc Welder, Welding, Welder, Arc Welder, Power Tool, Welding Solder, Tig Welding, Tig Welder, Mig Welding, Ac Welding Machine, Plasma Cutter, Cutting Machine, Plasma Cutting Machine, welding helmet and power tools. Features: 1.Intelligent interface conversion 2.Adopt IGBT single tube to ensure reliability 3.Unique switching power supply,wide application range of power supply 4.SMT chip design,ensure the duty cycle 5.32-bit microcomputer chip processor,real-time current display 6.Advanced high-efficiency inverter technology,35khz,high working frequency 7.Usable for generator, suitable for field operation 8.Automatically save the parameters of the last operation 9.Overheat,over voltage,under voltage protection to prevent machine damage 10.Colored LCD display,easy to use WHY CHOOSE US? Q1.Are you manufacturer or trading company? A.We are the only manufacturer of electrical products.Welcome to visit our factory at any time. Q 2. what's the payment term? A. We accept T/T etc. Q 3. What's the delivery time ? A. Normal model 1-3days,because we have ability to do the stock.For big order,it takes about 15-20days. Q 4. What is the standard of package? A. Export standard package or special package according to customer requirement. Q 5. what kind of product quality your factory offer? A. We are professional factory and we offer top quality to help client to get more market. Q 6. Do you accept OEM business? A. We do OEM . Q 7.Which market do you already sell? A.We already ship to Europe,America, Oceania etc. Q8. what kind of certificate you have ? A.We have CE, GS, ROHS, EMC etc. Model CUT-30 CUT-45PFC CUT-60CNC CUT-65CNC CUT-80CNC CUT-100CNC CUT-120CNC Rated Input Voltage(V) 1~230 95~275 3~400 3~400 3~400 3~400 3~400 Input Frequency(Hz) 50/60 50/60 50/60 50/60 50/60 50/60 50/60 Rated Input Current(A) 40 29 15.7 18 30 33 43 No-load Voltage(V) 320 265 400 400 415 415 415 Power Factor 0.65 0.99 0.7 0.7 0.7 0.7 0.7 Output Current Range (A) 10-30 10-45 15-60 15-65 15-80 15-100 15-120 Duty Cycle(%)40C�° 25% 25% 60% 60% 60% 60% 80% Efficiency(%) 80 80 80 80 80 80 80 Insulation Class H H H H H H H Protection Class Ip23 Ip23 Ip23 Ip23 Ip23 Ip23 Ip23 Weight(Kg) 7 8.5 18 20 25 30 32 Dimension(mm) 360x180x330 410X180X330 410X220X405 410X220X405 450X220X405 450X220X405 550X260X490
