Dolomite is a carbonate mineral composed of calcium magnesium carbonate. Dolostone (dolomite rock) is composed predominantly of the mineral dolomite with a stoichiometric ratio of 50% or greater content of magnesium replacing calcium, often as a result of diagenesis. Limestone that is partially replaced by dolomite is referred to as dolomitic limestone. Raw dolomite first enters jaw crusher to be crushed to smaller size. They are lift to storage room by elevator. Vibrating feeder will feed materials into grinding chamber evenly and gradually. After being grinded, the quartz powder will be blow to cyclone by blower. Then the dolomite powder will be transferred to storage room through pipes, and then will be discharged as final products. >>The Application of dolomite ultrafine powder grinding mill: HGM series dolomite ultrafine powder grinding mill is mainly applied to non-inflammable, non-explosive and brittle materials with Mohs hardness under six. Such as calcite, chalk, gravel, dolomite, kaolin, gypsum, etc, totally more than 100 kinds of materials. Product fineness can be controlled between 325~2500 mesh. >>Working Principle of dolomite ultrafine powder grinding mill: The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse powder materials return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler. Should you have any questions, please do not hesitate to contact me.
Introduce of Stone mill/micro mill/ micro grinder mill/ micro grinding mill: five models: HGM80, HGM90, HGM100, HGM100A, and HGM125 finished production fineness: 300meshes~3000meshes, 5-47 micron the capacity (ton/hour) ranges from 0.4T/H to 12T/H application: HGM series stone mill/micro mill/ micro grinder mill/ micro grinding mill can process various kinds of stones and rocks, such as: Kaolin, limestone, calcite, marbles, barites, gypsums, pyrophyllites, dolomites, calcium carbonates, pigments, clays, coals, carbon black, activated carbons, feldspar, talc, mica, carbon black, petroleum coke, alumina, chromic oxide, quartz, cements, up to more than 100 materials. Working Principle of Stone mill/micro mill/ micro grinder mill/ micro grinding mill: The crusher will crush the big materials into small ones, and then the elevator will send them to the hopper. The vibrating feeder will send the materials to the middle of first dial evenly. The motor of main equipment drives the main shaft and dial through reducer, and the dial drives numbers of rollers moving in the ring channels via pins. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and bring the crushed materials to classifier. The rotating turbo in the powder collector will make the coarse materials return to the mill and regrounded, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
Limestone is a sedimentary rock composed largely of the minerals calcite and aragonite, which are different crystal forms of calcium carbonate. A few of limestone are composed from skeletal fragments of marine organisms such as coral or foraminifera. Limestone is usually processed in fine or super fine powder by limestone grinding mill. Limestone grinding mill is a main kind of stone grinding mill. Limestone grinded by CLIRIK limestone grinding mill has numerous uses: as a building material, as aggregate for the base of roads, as white pigment or filler in products such as toothpaste or paints, and as a chemical feedstock. The Application of limestone grinding mill: HGM10036 limestone grinding mill is mainly applied to non-inflammable, non-explosive and brittle materials with Mohs hardness under six. Such as calcite, chalk, limestone, dolomite, kaolin, gypsum, etc, totally more than 100 kinds of materials. Product fineness can be controlled between 325~2500 mesh. Working Principle of limestone grinding mill: The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of rollers, which are rolling in the ring, are driven by dial through plunger. After crushed by hammer crusher, the big materials become small ones and are sent to storage hopper by elevator and further sent to the middle of first dial evenly by the electromagnetic vibrating feeder and feeding pipe. The materials will be driven to the edge of dial by centrifugal force and fall down into the ring, crushed and grinded by roller, and become powder after production of three rings. The high pressure centrifugal blower will inhale air from outside and blow the crushed materials to classifier. The rotating turbo in the powder concentrator will make the coarse powder materials return to the mill and reground, while the fineness will mix with the air and go into the cyclone and be discharged in the discharge bin, which is at the bottom of it. The air, which mixed with very little fineness, will be purified by impulse duster and discharged by blower and muffler.
A non-toxic mineral, gypsum can be helpful to humans, animals, plant life, and the environment. While the majority of gypsum produced in North America is used to manufacture gypsum panels or building plasters, gypsum can also be used: as a soil additive As an additive in turbid water, particularly ponds, to settle dirt and clay particles without injuring aquatic life, as a food additive, as a color additive for drugs and cosmetics, a primary ingredient in toothpaste. Gypsum also has played an important role in the entertainment industry. Gypsum powder grinded by gypsum grinding mill can be used in more areas. So CLIRIK engineer will introduce CLIRIK gypsum grinding mill to you. Gypsum ultrafine grinding mill is mainly used in mining, building materials, chemical, metallurgical and other industries. It can process stone materials that moisture content less than 5%, Mohs hardness under 6 levels, such as kaolin, limestone, talc, barite, dolomite, calcite, marble, gypsum, bentonite, mica, graphite, and so on. The finished powder size can be 3000meshs. HGM series gypsum grinding mill is the technology team of Shanghai Clirik machine Co., LTD through long-term research about gypsum characteristics, and field investigate production process of gypsum processing factory, overcome varies problems appeared in the process of gypsum making, developed new generation grinding equipment. The gypsum grinding equipment is the result of our technical staff after years accumulated experience and test innovative, it can be used not only for gypsum powder processing, can also be used to manufacture calcite, barite, marble and other stone materials. It also has many appellations, such as calcite mill, barites mill, calcium carbonate mill, mica mill, dolomite mill. Gypsum grinding mill is the preferred stone machining equipment.
Product description, Product introduction: Bentonite is clay rock with the main minerals of montmorillonite, it belongs to the aquifer shape aluminum silicate minerals. Physical properties of bentonite: Mohs Scale Hardness is from 2 to 2.5,density is 2.6 g/cm3 ,and the color is white or light yellow.Bentonite is characterized by the natures of strong hygroscopicity, decentralization, suspension, certain viscosity, Thixotropy and lubricity, and strong cation exchange capacity.Bentonite is used in Brake pad Drum brake or clutch, The recommended regular consumption of kaolin is from 2% to 8%. The character of bentonite: Bentonite is of oil luster, waxy luster, earthy luster. The fracture is of shells or dentate shape.Sodium base bentonite is dense clumps commoly, calcium base bentonite is loose earthy commonly, the surface has smooth feeling, relative density is 2- 3.Bentonite has strong hygroscopicity, the biggest water quantity is 8 to 15 times of its volume, it will expansion from several times to thirty times after water absorption.Bentonite has High plasticity and good cohesiveness. The main chemical ingredients of Bentonite are K,Na,Ca, etc., and these ingredients often exist in different content in bentonite. The Na2O and CaO content directly affects the physical and chemical properties of bentonite.Sodium base bentonite has better expansibility and cohesiveness than that of calcium base bentonite.To meet many application needs,it need to change bentonite base to improve the technical performance of bentonite. Because the variety of excellent performance, bentonite can be used as binder, Filler, catalyst, stabilizer, plasticizer and thickener etc..Bentonite can be used as filler in friction material to reduce cost. Property: A1203: 18% min SiO2: 56% min Na2O+K2O: 2%-3% PH: 8.5-10.6 expansion coefficient: 20times-30times grade: 200mesh,325mesh sieving rate: 97%
Product name: stpp Specifications: 94.0%-96.0% Product category: sodium salt Sodium tripolyphosphate (stpp¡¡§o©granular /powder 1.Specification: Indexes Industrial grade Food grade Na5p3o10 94.0%min 94.0%min P2 o 5 57.0%min 57.0%min Water insoluble matter 0.15%max 0.04%max Iron(fe) 0.015%max 0.006%max Ph value (1% water solution) 9.2-10.0 9.5-10.0 Heavy metal (as pb) - 0.001%max Arsenic (as) - 0.0003%max Fluoride (f) - 0.003%max Whiteness 92%min 92%min Ignition loss 1.0 / Density (g/cm3) 0.35-0.9 0.35-0.9 Phase i 10-30 10-30 2.Uses: used as one of the main auxiliaries for synthetic detergent, synergist for soap; water Softener, tanning agent for leather making, auxiliary for dyeing; as an effective dispersion agent For suspensions of coatings, kaolin, magnesium oxide, calcium carbonate and drilling mud etc.; As an oil contamination resistance agent in paper production. In foodstuff industry it is used as Quality improver in the process of canned food, fruit juice drinks, foodstuffs from milk or soybeans. It may tender the meat in canned ham and soften the skin of horse bean in canned horse bean. It may also serves as a softener or densifier in foodstuff industry. 3.Packing: 25kg/p.P. Bag or according to the buyer's own requirement. 20mts/20" fcl .Packing: 25kg/p.P. Bag or according to the buyer's own requirement. 20mts/20" fcl
Full Name: Sodium Tripolyphosphate (STPP) Properties: White particle or powder, appearant density 0.35-0.9g/cm, melting point 622. Easily soluble in water, aqueous solution is alkali. Hydrolyze to orthophosphate in water, complaxing with calcium, magnesium, iron and other metal ions and generate soluble complex. Usage: Used as one of the main auxiliaries for synthetic detergent, synergist for soap; water softener, tanning agent for leather making, auxiliary for dyeing; As an effective dispersion agent for suspension solutions of coatings, kaolin, magnesium oxide, calcium carbonate and drilling mud etc.; As an oil contamination resistance agent in paper production. In food industry it is used as quality improver in the process of canned food, fruit juice drinks, foodstuffs from milk or soybeans. It may also serves as a softener or densifier in foodstuff industry. Packaging: 25kg bags, 50lb bags, 1000kg jumbo bags Technical Data Sheet: Parameter Guarantee Tech Grade Food Grade appearance White powder or granular White powder Main content % 94.0 94.0 P2O5 % 57.0 57.0 PH Value (1% water solution) 9.2-10.0 9.4-10.0 Heavy Metal (as Pb) % -- 0.001 Arsenic (As) % -- 0.0003 Fluoride (F) % -- 0.003 Water Insoluble Matter % 0.1 0.05 Fe % 0.02 0.01
Full Name: Sodium Tripolyphosphate (STPP) Properties: White particle or powder, appearant density 0.35-0.9g/cm,³ melting point 622. Easily soluble in water, aqueous solution is alkali. Hydrolyze to orthophosphate in water, complaxing with calcium, magnesium, iron and other metal ions and generate soluble complex. Usage: Used as one of the main auxiliaries for synthetic detergent, synergist for soap; water softener, tanning agent for leather making, auxiliary for dyeing; As an effective dispersion agent for suspension solutions of coatings, kaolin, magnesium oxide, calcium carbonate and drilling mud etc.; As an oil contamination resistance agent in paper production. In food industry it is used as quality improver in the process of canned food, fruit juice drinks, foodstuffs from milk or soybeans. It may also serves as a softener or densifier in foodstuff industry. Packaging: 25kg bags, 50lb bags, 1000kg jumbo bags Technical Data Sheet: Parameter Guarantee Tech Grade Food Grade appearance White powder or granular White powder Main content % 94.0 94.0 P2O5 % 57.0 57.0 PH Value (1% water solution) 9.2-10.0 9.4-10.0 Heavy Metal (as Pb) % -- 0.001 Arsenic (As) % -- 0.0003 Fluoride (F) % -- 0.003 Water Insoluble Matter % 0.1 0.05 Fe % 0.02 0.01
Dry anti-penetration castable to extend the life of the cathode liner has a positive effect. On the one hand can buffer the cathode carbon block uplift; the other hand can strengthen the bottom of the security The ability to reduce the heat loss at the bottom of the tank and to increase the temperature of the cathode carbon block itself and to reduce the temperature gradient between the upper and lower sides of the cathode carbon block. Due to dry Dry anti-penetration castable can be infiltrated with the electrolyte to produce a layer of 5 to 15 mm thick, dense glass-like kaolin barrier layer: This barrier, on the one hand, prevents the electrolyte from continuing to penetrate the lower part and protect its lower part The temperature of dry anti-penetration castable is not destroyed; the other hand, because the barrier layer with plasticity and particle layer has a certain compressibility, can effectively alleviate the furnace uplift, Deformation of the tank shell and other issues. Therefore, in the aluminum furnace in the furnace process, it can be placed directly on the insulation brick, the compaction of the upper part of the upper directly placed.
Sodium Tripolyphosphate 1.yname: Sodium Tripolyphosphate 2.Molecular formula:Na5P3O10 3.Molecular Weight: 367.86 4.Properties: White powder; Melting point 622â??; Easily soluble in water; It has got salient chelating capacity to ions of Ca and Mg etc. and can soften hard water to make suspension solution become into clear solution; It has got weak alkalinity but no corrosiveness. It is a surfactant, and has got outstanding emulsification to lubricants and fat. 5.Uses:Used as one of the main auxiliaries for synthetic detergent, synergist for soap; water softener, tanning agent for leather making, auxiliary for dyeing; As an effective dispersion agent for suspension solutions of coatings, kaolin, magnesium oxide, calcium carbonate and drilling mud etc.; As an oil contamination resistance agent in paper production. In foodstuff industry it is used as quality improver in the process of canned food, fruit juice drinks, foodstuffs from milk or soybeans. It may tender the meat in canned ham and soften the skin of horse bean in canned horse bean. It may also serves as a softener or densifier in foodstuff industry. 6.Packing:In 25Kg net WPP/PE bags. 7.Storage:It must be prevented from Damp ness and water. Don't store it in the open air.
CAS NO: 7758-29-4 Appearance: white crystal powder Package: 25kg/bag Application: 1) .as one of the main auxiliaries for synthetic detergent, synergist for soap; water softener. 2).Tanning agent for leather making, auxiliary for dyeing; 3).As an effective dispersion agent for suspensions of coatings, kaolin, magnesium oxide, calcium carbonate and drilling mud etc.; 4).As an oil contamination resistance agent in paper production. 5).In foodstuff industry it is used as quality improver in the process of canned food, fruit juice drinks, foodstuffs from milk or soybeans. It may tender the meat in canned ham and soften the skin of horse bean in canned horse bean. It may also serves as a softener or densifier in foodstuff industry. Our Advantages: Most competitive pricing Strict quality control Respond in 24 hours to inquiry, feedback or other requirements Shortest delivery time. we will take pictures before and after loading as proof for clients' review.
Plastic mill/non-ferrous metal mill Working principle: The material and air flow are rotating with the high speed rotation when the equipment is running.The materials are crushed by the strong air pressure, strong shear force and fierce impact with each other on the grinding block composed of turbine rotor and abrasive bricks of the sieve circle.It is on the basis of the airflow and the machine, and turn into the products such as uniform particle, small particle size distribution range. The performance and feature The machine has many advantages, including low energy consumption, high efficiency, long life, easy maintenance and change parts and so on. Especially for the powder separation of the combination or compound of metal and nonmetal.It can make all kinds of metal into a round ball, this is good use for electrostatic and separation.The patent of this machine is zl200820148816.9. Applicable scope This machine is widely used to all kinds of materials under the medium hardness , such as the plastic (polyethylene, polyester, polypropylene, polyvinyl chloride, polyethylene, polypropylene, nylon, pom, etc.), rubber, chemical dyes (salt, pigment, gesso, paint, kaolin, etc.), pesticide, medicine, food, feed, non-ferrous metals (copper, aluminum, iron, magnesium, etc.) or nonmetallic minerals (such as asbestos, glass, clay, etc.) and so on . Plastic mill/non-ferrous metal mill
Abs grinder | ppr mill grinder | abs price Working principle: The material and air flow are rotating with the high speed rotation when the equipment is running.The materials are crushed by the strong air pressure, strong shear force and fierce impact with each other on the grinding block composed of turbine rotor and abrasive bricks of the sieve circle.It is on the basis of the airflow and the machine, and turn into the products such as uniform particle, small particle size distribution range. The performance and feature The machine has many advantages, including low energy consumption, high efficiency, long life, easy maintenance and change parts and so on. Especially for the powder separation of the combination or compound of metal and nonmetal.It can make all kinds of metal into a round ball, this is good use for electrostatic and separation.The patent of this machine is zl200820148816.9. Applicable scope This machine is widely used to all kinds of materials under the medium hardness , such as the plastic (polyethylene, polyester, polypropylene, polyvinyl chloride, polyethylene, polypropylene, nylon, pom, etc.), rubber, chemical dyes (salt, pigment, gesso, paint, kaolin, etc.), pesticide, medicine, food, feed, non-ferrous metals (copper, aluminum, iron, magnesium, etc.) or nonmetallic minerals (such as asbestos, glass, clay, etc.) and so on . Abs grinder | ppr mill grinder | abs price
Metal mill/aluminum powder mill/non-ferrous metal mill Working principle: The material and air flow are rotating with the high speed rotation when the equipment is running.The materials are crushed by the strong air eddy current, strong shear force and fierce impact with each other on the grinding block composed of turbine rotor blades and u tooth plate in the machine, discharged outside the machine by the rear sieve mesh after crushing. Performance characteristics: The machine has the advantages with high efficiency, long life, low noise, good cooling, wide application range, easy maintenance and change parts, bearing chamber of the machine has water-cooling system , it can prolong the service life of bearing. It’s better for metal and nonmetal combination to mill and disintegrate , it can make all kinds of metal into a round ball, this is good use for electrostatic and separation. The machine patent number is zl200820148816.9 Application scope: This machine is applied to all kinds of materials which are under the medium such as plastic(pet, pvc, polyethylene, polypropylene, nylon, etc.), chemical dyes (salt, pigment, gesso, paint, kaolin, etc.), pesticide, medicine, food, feed, non-ferrous metals (copper, aluminum, iron, magnesium, etc.) or nonmetallic minerals (such as asbestos, glass, clay, etc.) Metal mill/aluminum powder mill/non-ferrous metal mill
HC3000-Super-Large Pendulum Mill in Asia, Technical Revolution of Pendulum Mill Industry, Upgraded Production of Traditional Raymond Mill HC3000 Super Large Grinding Mill is the largest pendulum roller mill in china, developed by our engineer on the basis of HC1700 grinding mill. With 5 patents, the HC3000 grinding mill is widely used to grind almost any non-metallic minerals with Mohâ??s scare of hardness below 7 and moisture below 10%, such as kaolin, calcite, marble, talc, manganese, ceramic, etc. The fineness can be adjusted from 0.18mm(80 mesh) to 0.038mm(400 mesh). Not only can the HC3000 grinding mill live up to the national industrial policy and meet the needs of mass production, but also fills the gap of large-scale mill in the mill industry. This kind of mill plays a leading role in grinding technology, production capacity and power consumption per ton. With a production capacity of 90T/H, the HC3000 grinding mill can replace all kinds of mill, especially suitable for large-scale powder-making industry such as desulfurization and manganese. Working Principle Powder processing system technological process: raw material will be transport to semi-open shed by special vehicle, and then be shoveled into the crusher to be crushed into particles smaller than 40mm. The material particles will be raised to the storage hopper by the elevator and then be evenly sent to the main mill for grinding by feeder. The qualified fine powder will be classified and blew to the pulse dust collector as product and finally discharged from the dust collector. The product will be transported to powder storage. The system is designed as open circuit system with full pulse dust collecting (able to collect 99.9% of the powder), so the equipment has higher capacity and lower pollution. The product can be deep-processed according to actual technology. HC grinding mill has really high capacity so the product cannot be packed by hand-filling, the packing job is supposed to be done after the powder be sent to the storage tank. Application Range HC3000 Grinding Mill is widely used to grind any non-metallic minerals with Moh's hardness below 7 and moisture below 10%, such as limestone, calcite, activated carbon, talc, dolomite, titanium dioxide, quartz, bauxite, marble, feldspar, barite, fluorite, gypsum, ilmenite, phosphorite, clay, graphite, kaolin, diabase, gangue, wollastonite, quick lime, silicon carbide, bentonite, manganese. The fineness can be adjusted from 0.18mm(80 mesh) to 0.038mm(400 mesh), whose range is much wider than that of traditional raymond mill.
Raymond Mill - the originator of Pendulum Grinding Mill In terms of traditional pendulum roller mill, the R-series grinding mill has been upgraded in many aspects. All of the technical parameters takes the leading role in China mill industry. The R-series grinding mill ranges from 2R to 6R, including 2R2713, 3R3220, 4R3216, 4R3218, 4R3220, 5R4121, 5R4125, 6R5127. This mill is widely used to grind any non-metal minerals with Moh's hardness below 7 and moisture below 6%, such as limestone, calcite, activated carbon, talc, dolomite, titanium dioxide, quartz, bauxite, marble, feldspar, fluorite, gypsum, barite, ilmenite, phosphorite, clay, graphite, kaolin, diabase, gangue, wollastonite, quick lime, silicon carbide, bentonite, manganese. The fineness can be adjusted from 0.18mm(80 mesh) to 0.038mm(400 mesh). Working Principle Raw material is firstly broken by jaw crusher into required particle size, which are carried by bucket elevator up to the storage hopper. The vibration feeder then conveys the crushed materials at a fixed rate into the grinding chamber of the main unit for pulverizing. The three rollers hung upon the spider-arm are running around the shaft. With the centrifugal force, the four rotational rollers will go around the ring tightly. The raw materials is put up between the rollers and rings by the blade to make the raw materials into powder. The grinded materials is blown up to the classifier, through which the powder is separated by the airflow. Coarse particles fall back down to the mill for regrinding. The needed particles will go into the collector where products will be removed through the discharge opening. The purified air flows to the air blower through the pipe above big cyclone collector. Air flue is circular type. Air stream in all pipelines is negative pressure except for that in the air blower and grinding chamber, which improved the working condition in the workshop. Wind volume in air flue increases as the moisture in material changes into vapour leaking in from the flange conjunctions and feed opening. Added air volume is transporting through the air blower and after-wind pipe, to simple collector. The end powder enters the collector with air stream and discharged from discharge valve. Application Range R-series Grinding Mill is widely used to grind any non-metallic minerals with Mohs hardness below 7 and moisture below 6%, such as limestone, calcite, activated carbon, talc, dolomite, titanium dioxide, quartz, bauxite, marble, feldspar, barite, fluorite, gypsum, ilmenite, phosphorite, clay, graphite, kaolin, diabase, gangue, wollastonite, quick lime, silicon carbidebentonite, manganese. The fineness can be adjusted from 0.18mm(80 mesh) to 0.038mm(400 mesh), whose range is much wider than that of traditional raymond mil l.
The most Economic and Practical Ultra-fine Powder Processing Equipment, the Energy-saving and Reduce Consumption Equipment fro ultra fine Powder Processing HCH ultra-fine grinding mill is especially suitable for ultra fine grinding. With yearsâ?? accumulation of experience in R&D, the HCH Ultra-fine Grinding Mill is a new ultra fine pulverizing equipment designed by Hongcheng. This mill is widely used to grind any non-metal minerals with Moh's hardness below 7 and moisture below 6%, such as talc, calcite, calciumcarbonate, dolomite, bentonite, kaolin, graphite, carbon black, etc. HCH Ultra-fine Grinding Mill features in space-saving, completeness, wide usage, easy operation, smooth performance, high performance-cost ratio and high efficiency. HCH1395 Grinding Mill is the biggest ultra fine circle-roll grinding mill in China. Working Principle Technological process: The pre-grinding raw ore material will be crushed into particlesï¼?10mm and transport to the feeding hopper by the elevator, then feed into the grinding chamber by the feeder. The grinding rollers equip on the rotary table rotates around the centre shaft. There is flexible gap between the roller and ring. The rollers rotate outward by the centrifugal function to compress the fixed ring. The rollers also self- rotates around the roller pin. When material passed through the gap between the ring and roller, the material will be smashed by the rotating rollers. Four layers of rollers. Material will be grinded 1st time when passing the 1st layer of roller and ring. Then be grinded second, third and fourth time when loop through each layer rollers. Thus the materials were grinded sufficient and obtain much fine powder. The powder fallen down onto the bottom table by gravity will goes up to the classifier for separation by the airflow from blower. The qualified fineness passing from the classifier will be collected by the pulse bag collector as final product, while unqualified fallen down for regrinding till passing through. The powder goes with air flow into the pulse bag filter and collects by the discharging valve. The wind path is in circulation and the airflow is in negative pressure. There will be no dust escape, so the equipment can ensure a no dust operation in workshop. Application Range HCH Ultra-fine Grinding Mill is widely used to grind any non-metallic minerals with Mohs hardness below 7 and moisture below 6%, such as talc, calcite, calcium carbonate, dolomite, bentonite, kaolin, graphite, carbon black etc.. This kind of mill is especially suitable for ultra fine grinding. The fineness can be adjusted from 0.045mm(325 mesh) to 0.005mm(2500 mesh), whose range is much wider than that of traditional Raymond Mill.
Cheap-Affordable-Quality Diatomite & Diatomaceous earth. We have abundance supply around the world, just send us your HS code or SKU number and last invoice so we can give 10% discount.
Total Nitrogen content 18% Total P2O5 46.0 % Water Soluble P2O5 43.0 45.8 H2O 2.0 % Max
P2O5 30% P2O5 28%