ASTM B163 is the Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-exchanger Tubes. This covers outside diameter and average wall, or outside diameter and minimum wall tube. The tube shall be furnished in the alloys and conditions defined by this specification. The ASTM B163/ASME SB163 material shall conform to the composition limits of nickel, copper, molybdenum, iron, manganese, carbon, silicon, chromium, aluminum, titanium, phosphorus, cerium, and zirconium, yttrium, boron, cobalt, columbium, tungsten, and nitrogen specified. Tensile strength, yield strength, elongation, and Rockwell hardness of the material shall conform to the required Mechanical Properties set by this specification. Test methods such as chemical analysis, tension, rounding procedure, Rockwell hardness, grain size, and hardness conversion shall be performed for qualified ASTM B163/ASME SB163 alloy tubes. ASTM B163/ASME SB163 NICKEL ALLOY PIPE/TUBE PROVIDED BY YUHONG ASTM B163/ASME SB163 Nickel Alloy Pipe/Tube The most popular materials under ASTM B163 Standard are: UNS N04400(Monel 400); UNS N06600(Inconel 600); UNS N08800(Inconel 800); UNS N08810(Incoloy 800H); UNS N08811(Incoloy 800HT); UNS N08825(Incoloy 825). Incoloy 800/N08800 Nickel Alloy Pipe/Tube Incoloy 800H/N08810 Nickel Alloy Pipe/Tube Incoloy 800HT/N08811 Nickel Alloy Pipe/Tube Incoloy 825/N08825 Nickel Alloy Pipe/Tube Inconel 600/ N06600 Nickel Alloy Pipe/Tube Inconel 601/ N06601 Nickel Alloy Pipe/Tube Monel 400/N04400 Nickel Alloy Pipe/Tube Nickel 200/N02200 Nickel Seamless Pipe/Tube ASTM B163/ASME SB163 Nickel Alloy Pipe/Tube ASTM B163/ASME SB163 NICKEL ALLOY PIPE/TUBE FEATURES Nickel alloys tube under ASTM B163 can meet the High Strength and corrosion resistance in a range of media including sea water, hydrofluoric acid, sulphuric acid, and alkalies. ASTM A163 Coiled Tubing is highly resistant to corrosion in different environments. This tubing enables the speed of the operation to be fast at the same time, it is very safe and easy to run. ASTM B 163 Tubing is used in applications for drilling, logging, fracturing, perforating, and production operations. These tubings have a lower environmental impact. If you are looking for a reliable ss pipe company, don't hesitate to contact us!
Simcon®-WPR 1000 Water Proofing & Reducing Type : Pce Based Water Reducing Superplasticizing Set Retarding Concrete Admixture ALL IN ONE TYPE ADMIXTURE DESCRIPTION Simcon®-WPR 1000 Imparts high workability and gives workability retention. USES Simcon®-WPR 1000 a superplasticizer for free flowing con- crete in floor, slabs, foundations, walls, plasters slender components with dense reinforcement, walls, columns, pavements and other structural and non structural elements. Specially recommended for the following types of con- crete: Ready mix concrete Pre cast concrete Site batched concrete CHARACTERISTICS / ADVANTAGES Simcon®-WPR 1000 produces a more uniformly cohes-ive high quality free flowing concrete. It has following advantages : Improved water reduction. Improved strength and density Improved consistence retention Improved durability Improved water tightness/ water proofed concrete PRODUCT INFORMATION Improved surface finish Improved cohesion properties Suitable for hot weather conditions Water reduction up to 15-20 % depending on dosage* * This will depend on dosage and mix design Composition Modified Napthalene Formaldehyde Sulphonate Packaging 1KG,5KG,10KG,20KG. Appearance / Colour Dark Brown Liquid/Coffee,Honey Colour Colour Shelf life 24 months from date of production if stored properly in undamaged un- opened, original sealed packaging. Storage conditions Store in dry conditions at temperatures between +10°C and +40°C. Protect from direct sunlight and frost. Density ~1.17 kg/l at 25°C pH-Value â?¥ 6 Application Dosage : 250ML Per 50KG Cement Bag Compatibility Simcon®-WPR 1000 may be combined with many other Simcon® products. Important: Always conduct trials before combining products in specific mixes and combinations. Compatible with all types of cement and cemen- titious material APPROVALS / CERTIFICATES International ISO Certified - Dubai Acccreditation Center ISO 9001: 2015 Certified Bangladesh Department Of Environment Certified Bangladesh Fire Service & Civil Defense Certified Bangladesh Fire Service & Civil Defense Certified Our Products Are Also Tested By Buet
bestscooterstore * com Product Description ORBEA CARPE 10 DISC HYBRID BIKE 2021 Ultimately versatile, the Orbea Carpe 10 Disc Hybrid Bike is designed to fit around your busy lifestyle. Built on a high-quality Aluminium 6000 frame, this bike is robust and lightweight, making it perfect for daily commutes and leisure rides, while the inclusion of a rear rack means you can even carry your shopping home too. High-quality Shimano components deliver crisp and reliable shifting through the 10-speed Deore gearset, while hydraulic disc brakes are the perfect addition to help you stop with modulation in any weather. And when it's raining, you'll enjoy the benefits of the included SKS EDGE mudguards to help you stay dry. Another fantastic addition to this bike's specification is the dynamo-powered light set. A Spanninga Pixeo rear light and Kendo XDAS front light are powered by the dynamo and won't run out of batteries, so you can ride safely in the knowledge you're easier to spot on the road. HIGHLIGHTS Orbea Urban Speed Aluminium 6000 frameset Lightweight carbon fork for nimble handling and smooth ride feel High-quality Shimano Deore 10-speed gearset Powerful Shimano hydraulic disc brakes Dynamo powered front and rear lights Rear luggage rack SKS mudguards SPECIFICATION Frame� � � Orbea Urban Speed Aluminium 6000, Orbea Tube Shaping, Flat Mount Disc Brake, 135x9mm QR, Carrier and Mudguard compatible, max 700x40C, Inner Cable routing Fork  Orbea Speed 400mm Carbon, Flat Mount Disc Brake Stem Orbea TDS-C301 Handlebar Orbea AL320 Riser 680mm Front Brake  Shimano MT200 hydraulic disc Rear Brake  Shimano MT200 hydraulic disc Brake Levers  Shimano MT200 hydraulic disc Front Derailleur  N/A Rear Derailleur  Shimano Deore M5120 SGS Shadow Plus Shift Levers  Shimano Deore M4100 10-speed Cassette  Shimano Deore M4100 11-46t 10-speed Crankset  Orbea Alloy 42t Front Whee  Orbea Airline Corsa Disc 700 x 19c clincher Rear Wheel  Orbea Airline Corsa Disc 700 x 19c clincher Front Tyre  Kenda K1067 700x38C Reflective type plus puncture protection, clincher Rear Tyre  Kenda K1067 700x38C Reflective type plus puncture protection, clincher Saddle  Velo 1221 Seatpost Orbea C255 27.2x300mm Accessories  Orbea rear luggage carrier (Max Front Light  Joss Spanninga Kendo XDAS Dinamo Rear Light Spanninga Pixeo Dynamo  Shimano DH-3D37-NT, 6V Dynamo 3.0W
Product Details Description :Gold/Silver/Colored Plain or Embossed Metallic Paper Color: Gold, Silve rRed, Blue,Green,Copper,Fuchsia,Gold,Light Blue and customized Laser color :Red,Fuchsia,Pink,Blue,Green,Golden,Sliver and more colors customized Base Paper Offset Paper, Art Paper,FBB,SBB,Duplex Board, Kraft Paper, Manila board etc. Embossed Pattern Rose, Linen, Ripple, Phoenix tail, Nest, Music, Bark line, Grape Leaf, Small Grid Application Gift packing, printing, handicraft works, packing box, DlY materials,arts & crafts, greeting card, decoration etc.Custom design OEM/ODM Available Specification: Description: Gold/Silver/Colored Plain or Embossed Metallic Paper Color: Gold,Silver,Red,Blue,Green,Copper,Fuchsia,Gold,Light Blue Laser color : Red,Fuchsia,Pink,Blue,Green,Golden,Sliver and more colors customized Base Paper: Offset Paper,Art Paper,FBB,SBB,Duplex Board,Kraft Paper,Manila board etc Embossed Pattern: Rose,Linen,Ripple,Phoenix tail,Nest,Music,Bark line,Grape Leaf,Small Grid More than 100 different embossed designs for your select,also can customized Laminating: Aluminum foil,Aluminum film,PET film etc Size: 1.Big Size:70x100cm,50x70cm or customized 2.Small Size:A2,A3,A4,A5,Letter Size,Legal Size GSM: 100g,120g,180g,200g,250g,270g,320g,370g etc Packing: 1.Big size:100/125/200/250 sheets per pack with Kraft paper. 2.Small size:50/100/500 sheets per OPP bag or as per customer requirements Application: Gift packing,printing,handicraft works,packing box,DIY materials, arts&crafts,greeting card,decoration etc. Custom design: OEM/ODM Available Payment terms: L/C,D/A,D/P,T/T,Western Union,Money Gram Delicate white paper with a semi-translucent qualty becomes something special when printed with your design. Tissue paper is the final layer between your client and your product, and sets the expectations high for what will be revealed underneath. We offer gorgeous premium colors for your design such as metallic gold and silver to give a regal feel to your tissue paper. Packing need not be boring plain-custom printed tissue paper is one the most delicate and detailed options you can find.
4.Main technical parameters 4.1. Capacity: 5, 10, 20, 25, 50100200kg (optional) 4.2. Unit switching: kg, N, LB 4.3. Load decomposition degree: 1/250,00 4.4. Load accuracy: 0.25% 4.5. Maximum stroke: 1000mm (excluding fixtures) 4.6. Test speed: 30-300 mm/min 4.7. Displacement resolution: 0.01 mm 4.8. Display device: touch screen (capable of displaying and printing test times, test values, maximum values, fracture values, etc.) 4.9. Motor: AC motor 4.10. Overall dimensions (L * W * H): 550 * 500 * 1240mm 4.11. Weight: 80kg 4.12. Power supply: 1 , 220V, 15A or specified 4.13. Delivery: One set of tension fixtures 5. Introduction to System Functions 5.1. It has tensile and pressure testing functions. 5.2. It has a pull stop function. 5.3. It can display displacement, has functions such as elongation, pressure, and other material testing machines. 5.4. There is an automatic stop alarm function for overload load setting. 5.5. It has an automatic save function, and can coexist with manual and automatic testing data up to ten times. 5.6. Use a list format to display the saved test data. 5.7. With an administrator password, users can modify their startup password to make machine management more secure. 5.8. Using software to calibrate the load value is extremely easy to calibrate. 5.9. The internal functions are set with full Chinese prompts, making the operation convenient and simple. 5.10. Rich testing functions, capable of conducting tensile tests, pressure tests, compressive tests, elongation tests, etc. 5.11. Display method: Real time display on the touch screen. 5.12. Tensile range: Standard configuration 200kg (optional). 5.13. The accuracy is 1/25000. 5.14. It can print test data and dates, making it easy to view test data for each stage 5.15. Conversion of three types of force units: N, Kg, and LB. During the testing process, 5 sets of test data at any position can be manually and automatically captured and printed. 7. Introduction This product tests the tensile strength, compressive strength, and elongation of various materials, semi-finished products, and finished products. It can perform tests such as peeling, tearing, bending, bending, and compression, and is suitable for use in industries such as metals, plastics, rubber, textiles, synthetic chemicals, wires and cables, leather, etc. 8. Design standards ASTM D903, GB/T16491, GB/T1040, GB/T8808, GB13022, GB/T 2790/2791/2792, CNS-11888, JIS K6854, PSTC-7, etc
The 350/450/570YDMQ Double Station rotary die cutting and slitting machine is also known for its stable and reliable performance, making it a long-lasting and dependable investment for any business. Its easy-to-operate design also allows for minimal maintenance, reducing downtime and increasing overall efficiency. Choose the 350/450/570YDMQ Double Station rotary die cutting and slitting machine for a comprehensive solution to your labeling needs. Main features: 1:Die cutting station(wall plate) is independent and high precision, different from the traditional bottom roller(wall plate) 2:Die cutting station adopt three roller structures to reduce the dancing of magnetic roller, and realize the stable and high speed running at 150m/min, and it can work for the 40gsm bottom paper, saving the material 3:single and double station is optional 4:can be online and inline with the automatic label production no glue turret rewinding machinery, advantage is no need the material storage rack, saving the space. 5:the unwinding part adopt the asynchronous motor to load the material, more stable than hydraulic or the pneumatic lifter. max unwinding diameter at 1200mm or 6000meters 6:Full servo driven for machine, it can work for both number counting and meter counting. 7:Heating fan can be stable productions at the cold weather, it can be easier for the waste scrapping 8:Scrapping waste can be mini 1mm, saving the material 9:Servo driven can realize the dotted line die cutting 10:Die cutting wall plate at thickness 38mm, can work stable running at high speed 11:Scrapping waste compare with snowball waste or magnetic waste rewinding, it can be realize non stop. Technical parameters: Model: 350YDMQ 450YDMQ 570YDMQ Max Slitting speed: 150m/min 150m/min 150m/min Max. Material Width: 350mm 450mm 570mm Max. Unwind dia: 1200mm 1200mm 1200mm Max. rewind dia: 1200mm 1200mm 1200mm Accuracy rate: ±0.10mm ±0.10mm ±0.10mm Max die cut speed: 150m/min 150m/min 150m/min Voltage: 380V/3P/50HZ 380V/3P/50HZ 380V/3P/50HZ Power: 9/14KW 9/14KW 9/14KW Dimension : 2710*1530*2500mm(single station) 3600*1530*2500mm(double station) 2710*1630*2500mm(single station) 3600*1630*2500mm(double station) 2710*1750*2500mm(single station) 3600*1750*2500mm(double station) Magnetic size: 60T-150T 90T-198T 90T-198T Die cutting bottom paper: 40-70gsm 40-70gsm 40-70gsm Machine weight: 2100/3000KG 2300/3200KG 2500/3400KG
Multiple Protections: Dry run protection Phase loss protection Overload/no load protection Short circuit protection Over-voltage protection Pump stalled/antiseizing protection Undervoltage protection Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
Multiple Protections:  Dry run protection Phase loss protection Overload/no load protection Short circuit protection Over-voltage protection Pump stalled/antiseizing protection Undervoltage protection Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
Multiple Protections:  Dry run protection  Phase loss protection Overload/no load protection  Short circuit protection Over-voltage protection  Pump stalled/antiseizing protection Undervoltage protection  Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
Multiple Protections Dry run protection Phase loss protection âOverload/no load protection â? Short circuit protection â? Over-voltage protection â? Pump stalled/antiseizing protection â? Undervoltage protection â? Pump shaft rust protection Major Features: 1,Pressure control: electric contact pressure gauge or pressure switch 2,Water level control: probe or float switch 3,Multifunction display â?? visualization of: voltage, motor current, upper/lower tank status and alarms 4,Upper tank for water supply control and lower tank for drainage control 5,Operation mode: AUTO/MANUAL switch 6,Fault indication: fault tracking,last 10 fault reason display,audio/light alarms. 7,Anti-card protection,long-term non-use of the pump, 15 days to start once. 8,Setting protection current for motor overload/no-load,no-load delay restart time adjustable. 9,Automatic restart when voltage comes to normal rating after over-voltage/under-voltage protection. 10,Automatic restart after power failure recovery. 11,Time setting ON/OFF 12,Push button for adjustments and set up from display 13,Restore factory setting: press both "Overload" and "NO-Load"for 3 seconds. 14,Automatic re-starting pump from dry running,restart time range 0-999 minutes adjustable.
Ceramic Fiber Board Density: 260-320 kg/m ³ (16-20 lb/ft ³) Raw materials: Spun ceramic fiber bulk Thickness: 10mm, 20-50 mm Asbestos: 100% Non Asbestos Function: Refractory & Fireproof & Insulation ROSEWOOL ceramic fiber board is made of ceramic fiber cotton by the process of vacuum forming or dry process refined by dry and machining. It has good specialties of rigid ity flexibility heavy intensity anti-wind erosion, non-expansion, lightweight, and easy to construct. It can be cut and bent optionally. Thus, it is the practical and efficient material of kiln and furnace, pipe and other thermal insulation equipment. Ceramic Fiber Board Application 1. The wall liner and back lining materials of high-temperature reaction, reheating equipment and various industrial furnace such as used glass tempering furnace, pottery kiln, ceramic kiln and tunnel kiln 2. Insulating and fire proof plate of furnace door and roof or house chimney and fireplace 3. Lows fire proof and insulation for chimney cake ovens, pizza oven 4. Boilers and heater combustion chamber 5. Aluminum factories-reduction cell firebricks back linings 6. Ladle furnace backing 7. Shipping, aviation, precision industrial equipment 8. Refractory and thermal insulation material in kiln or furnace of construction industry for heating and wall liner of high-heat treatment
The High-Speed Laser Engraving & Marking Machine is a cutting-edge tool designed specifically for non-metal items in industries such as footwear, bags, garments, gifts, and decorations. This versatile machine combines high-speed engraving and marking capabilities, ensuring efficient and precise processing of a wide range of materials. High-Speed Engraving and Marking: This machine utilize advanced laser technology to deliver high-speed engraving and marking on non-metal items. It can swiftly create intricate designs, patterns, logos, and text with exceptional precision, providing fast and efficient production capabilities. Versatile Material Compatibility: The machine is compatible with various non-metal materials commonly used in the footwear, bag, garment, gift, and decoration industries. It can process materials such as leather, fabric, wood, acrylic, glass, plastic, and more. This versatility allows for a wide range of applications and creative possibilities. Large Working Area: With a spacious working area of 300*300 mm, this machine accommodates a variety of item sizes, allowing for efficient processing of different shapes and dimensions. Water Cool Chiller System: The integrated water-cooled chiller system helps maintain the optimal temperature of the laser and extends its lifespan. It effectively dissipates the heat generated during operation, ensuring consistent performance, and preventing overheating issues. This feature enhances the machine's durability and reliability. User-Friendly Interface and Software: The machine is equipped with a user-friendly interface and software, making it easy to operate for both experienced users and beginners. The software offers intuitive controls, allowing users to import designs, adjust parameters before starting the engraving or marking process. It supports various file formats, providing compatibility with different design software. Model No. BS - 6060 Working Area 600 mm x 600 mm Laser Power 80W Repetition Precision + 0.0001 mm The smallest Characters 0.8 mm Linear Making Speed 7000 mm/s Response Time 0.8 ms Cooling way Water cooled Working Temperature 0 - 45C Working Humidity 5-95%
We've been designing and manufacturing air blower for 17 years since 2007. Located in Shandong, China, We supply 3 lobes roots blower/vacuum pump, air bearing turbo blower and also rotary vane type blower etc., applying in wastewater treatment, cement factory etc., providing air for the aeration of water. What we can offer: 1, High precision. Equipped with HMC and CNC machine, all the critical components of the blower are produced quickly and accurately under ISO9001 standard. 2, Stock. Regular models are stocked and customized orders only needs 5-7 days to finish. During 3 years covid, we try our best to cut down production time to help our client get quick capital turnover. 3, Less repair. Every set will be under a run-test at least 12 hours under max pressure. It is EVERY SET, not sampling check. Avoiding any sudden situation may happen when clients receive the blower.
Designed for reliability and efficiency, it features an automatic movement belt system. Perfect for heat transfer and cloth fusing, with adjustable heat, speed, and pressure for precision and accurate results Automatic Movement: Seamlessly navigate heat transfer and cloth pasting with the machine's automatic movement belt system, ensuring consistent and precise processing. Adjustable Heat: Fine-tune the heat settings to match your requirements, guaranteeing optimal heat transfer and cloth pasting outcomes. Adjustable Movement Speed: Customize the belt's movement speed to align with your production needs, ensuring efficiency and accuracy. Adjustable Pressure: Tailor the pressure settings to achieve uniform adhesion and dependable results for each project. Model No. BS-42 Voltage 220V Fusing Width 450/ 500/ 600/ 1000 mm Max Temperature 0-250�°C Heater Output 4 kw Motor Power 400 w Power Supply 220V, Single Phase Pressure 1.5kgs/cm2 Belt Speed 7mtr/min Fusing Time 5-20sec Machine Weight 170 - 200 kgs Machine Size 1850x 1130x 1280 mm
ZL-1 model Steam air heater with upper inlet and lower outlet is consists of 6 parts: steel-aluminum radiator fin tube + electric steam valve + drain valve + insulation box + fan + electric control system. Steam passes the though the fin tube, dissipating heat to the insulation box, mixing and heating the fresh or recycle air to setting temperature, fans bring this hot air into drying room or heating room to be used for dehydration, dehumidification or heating. 4. Advantages/features 1. Simple structure, beautiful appearance, low cost 2. Steel-aluminum finned tubes, high heat exchange efficiency. The base tube is made of 8163 seamless tube which is pressure-resistant and durable; 3. Electric steam valve controls the amount of inlet, automatically cuts off or opens according to the set temperature, so that can accurately controls the temperature. 4. Large air volume and small wind temperature fluctuation 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.
Sino-NSH-GED-WD is a waste oil regeneration system that cracks waste oil to diesel fuel. Sino-NSH-GED-WD adopts the atmospheric distillation technology, also known as cracking technology. During the distillation process, the waste oil is heated to the setting temperature and turns into oil mist, then it passes through the catalyst tower. After sufficient reaction with the catalyst, the oil mist passes through the condensing system to be cooled to liquid diesel. This system can be applied for gasoline motor oil, diesel motor oil, all kinds of engine oil, mineral oil, synthetic oil, transmission oil, hydraulic oil, gear oil and other used black lubricant oils to produce clean diesel oil. Diesel acquired from NSH-GED-WD system meets international standards and can be fully applied to burners, diesel engines, generators, etc. This system is very safe because the temperature setting is rigorous and the machines are stabilization. Our technical team commits to design the most reasonable and high efficient distillation system to realize the profit maximization of the both parties. Recovery rate is above 90% with low operation cost, only 5-6 USD for recycling one ton used oil.
Sino-NSH-GED-WD is a waste oil regeneration system that cracks waste oil to diesel fuel. Sino-NSH-GED-WD adopts the atmospheric distillation technology, also known as cracking technology. During the distillation process, the waste oil is heated to the setting temperature and turns into oil mist, then it passes through the catalyst tower. After sufficient reaction with the catalyst, the oil mist passes through the condensing system to be cooled to liquid diesel. This system can be applied for gasoline motor oil, diesel motor oil, all kinds of engine oil, mineral oil, synthetic oil, transmission oil, hydraulic oil, gear oil and other used black lubricant oils to produce clean diesel oil. Diesel acquired from NSH-GED-WD system meets international standards and can be fully applied to burners, diesel engines, generators, etc. This system is very safe because the temperature setting is rigorous and the machines are stabilization. Our technical team commits to design the most reasonable and high efficient distillation system to realize the profit maximization of the both parties. Recovery rate is above 90% with low operation cost, only 5-6 USD for recycling one ton used oil.
9060/1390/1610 LASER CO2 6040 ENGRAVING CUTTING MACHINE This serial CO2 laser engraving cutting machine is with a smaller work size and 1 laser head. They are common styles in the current market and are most widely used in practical applications. They are good at engraving and cutting nonmetal materials, such as acrylic, wooden boards, paper, bamboo, dual-color boards, and other non-metallic materials. Compact structure, easy to move. 6040/9060/1390/1610 CO2 LASER ENGRAVING CUTTING MACHINE TECHNICAL PARAMETERS Model WH-1390 Work size 1300*900mm Machine size 1820*1320*1020mm Laser head quantity 2 Pcs Laser power 60w/80w/100w/130w/150w (Optional) Work table Blade table/Honeycomb table Engraving speed 0-60000mm/min Cutting speed 0-30000mm/min Driving system Stepper motor Resetting positioning accuracy 0.01mm Laser tube cooling Water cooling Max power About 1kw Machine control DSP controlling Power supply AC 110 - 220V, 50 - 60Hz Min. shaping character Chinese 2mm*2mm, English 1mm*1mm Supported graphic BMP, PLT, DST, DXP, and AI Software supported CorelDraw, AutoCAD, Photo shop Operating temperature 0â??ï½?45â?? Operating humidity 5%ï½?95% Standard assistant parts 550W Exhaust fan*2units Water pump*2units 195w air compressor*2units Optional parts CW3000w/CW5000/CW5200 chiller Motorized up down table Autofocus Red dot pointer Rotary axis Servo motor Features of 6040/Laser 9060/1390/1610 Co2 Laser Engraving Cutting Machine 01 The appearance is humanized in design, with front and rear material access and omni-directional wheel movement, making your production and processing more flexible. 02 This non-metal cutting machine adopts high-frequency uniform power 60W/80W/100W/150W/CO2 laser, capable of continuous 24-hour uniform output and strong anti-interference ability. 03 The machine adopts Ruida 6445G control system, which is mature and stable, supports offline USB usage, and is more convenient to use; It also has a breakpoint resume function. 04 It adopts linear guide rails from Taiwan, ensuring smooth motion trajectory and high speed accuracy. 05 The optical system utilizes II-VI high-transmittance focusing lenses and high-quality reflector mirrors, ensuring a finely constant beam, large cutting depth, and high engraving precision.
BRIGGS & STRATTON 10KW HOME STANDBY GENERATOR (STEEL) Price:$1,356.00 SKU:40375 Brand:Briggs & Stratton Condition:New Weight:1.00 LBS Shipping:Calculated at checkout Product Description Features 10 kW Fully Automatic Standby Generator Automatically starts when utility power is lost Advance Power Management (Transfer Switch Sold Separately) Combine with ATS to manage up to two 3-Ton AC units 570cc Briggs & Stratton V-Twin Commercial Grade Vanguard Engine Provides years of long lasting, reliable standby power Streamlined, Space Saving Design Sleek, compact profile blends in next to central AC unit Flexible Placement (Please Verify Local Building Codes) Tested against tough National Fire Protection Agency standards Can be placed as close as 18â?? from structure Front Air Ventilation Pushes engine exhaust out the front, away from the home Galvanneal Steel Enclosure Automotive rust proofing paint process reduces corrosion Auto Fuel Shutoff & Easier Maintenance Provides added safety during an emergency More service access & user-friendly control panel Includes Synthetic Oil & Battery Charger Industry Leading 5-Year Warranty Parts, labor & travel covered for 5-Years Specifications Engine Engine Brand Briggs and Stratton Vanguard Starting System 12v Auto Start CC 570 CC Consumer Engine Warranty 5 Years Engine RPM 3600 RPM Low Oil Alert/Shutdown Yes Product Specs Voltage 120/240 Single-Phase Frequency 60 Hertz Surge Watts 10000 Watts Rated Watts 10000 Watts Fuel Type LP/Natural Gas NG Power Capacity 9000 Watts LP Power Capacity 10000 Watts NG Fuel Consumption @ 50% Load 111 ft�³/hr NG Fuel Consumption @ 100% Load 169 ft�³/hr LP Fuel Consumption @ 50% Load 1.18 gallons/hr LP Fuel Consumption @ 100% Load 1.82 gallons/hr Rated Amps 42 Amps Decibel Rating @ 7m ? 75 dbA Transfer Switch Automatic (Not Included) Enclosure Steel Battery Not Included (540 CCA) A/C Ton Rating 3-Tons Mounting Pad Steel (Included) Cooling System Air Cooled UL Listed Yes Grade Type Emergency Overview Made in USA Yes Weight 272 Pounds Product Style Standby Generator Product Length 28 Inches Product Width 24.4 Inches Product Height 35.1 Inches Consumer Warranty 5 Years UPC 011675403751
bestscooterstore * com Product Description MOTOR SyncDrive Pro, 85Nm, powered by Yamaha CONTROLLER RideControl Ergo 3, grip integrated DISPLAY RideControl GO, frame integrated LED displayANT+ Wireless display compatible BATTERY EnergyPak Smart 625WhEnergyPak Plus range extender compatible FRAME ALUXX SL-grade Aluminum, Advanced Forged Composite Upper Rocker, 160mm Maestro suspension system, 'Boost' 148x12mm, UDHTM derrailleur hanger FORK RockShox Domain R 29er, 170mm travel, 15x110 Boost, Maxle Stealth, E-bike Approved SHOCK Fox Float DPS Performance, EVOL Large Volume sleeve, 2-position lever, 205x62.5mm Trunnion mount, custom tuned HANDLEBAR Giant Contact Trail, 35x800mm GRIPS Giant Tactal Pro-E, single lock-on STEM Giant Contact SL 35 SEATPOST Giant Contact Switch, dropper, 30,9mm (S:125, M: 150, L/XL:170) SADDLE Giant Romero Trail PEDALS Flat pedal SHIFTERS Shimano Deore FRONT DERAILLEUR MRP 1X HD2 custom co-molded chain guide REAR DERAILLEUR Shimano Deore 12-speed BRAKES Shimano Deore BR-M4120, 4-piston, hydraulic disc, 203mm BRAKE LEVERS Shimano Deore BL-M4100, I-spec EV CASSETTE Shimano Deore CS-M6100-12, 10-51T, 12-speed CHAIN KMC e.12 Turbo, EcoProteq, e-bike optimized CRANKSET Praxis Wavetm 36T Cold Forged 4130 premium steel Praxis e-Cadet+ custom forged crankarm set (S/M:160, L/XL:165) BOTTOM BRACKET - RIMS Giant AM 29"[F] 27.5"[R], Tubeless ready, 30mm inner width HUBS Shimano MT410 Boost, Center-Lock, [F] 110x15 [R] 148x12mm Micro-Spline Drive Body Thru-axle SPOKES Sapim E-Lite [r] Race [f] TIRES Maxxis Minion DHF 29x2.6" foldable, Tubeless, EXO+, 3C MaxxTerra[F]Maxxis High Roller II 27.5x2.5" foldable, Tubeless, DoubleDown, 3C MaxxTerra Compound [R] EXTRAS Tubeless kit (liquid, valves, levers, manual, tool) LIGHTING Optional:- Giant Recon series e-bike lights available and direct connectable
