Features for the Champion 100416 - Generator Tri-Fuel Technology Your 8000-watt portable generator operates on natural gas, propane, or gasoline, plus natural gas and propane hoses are included so the unit is ready to run on any fuel right out of the box. Electric Start Power up the 459cc Champion engine with the handy rocker switch, battery included. Intelligauge with CO Shield�® rack voltage, frequency, session run time, and total run time to monitor output and track maintenance intervals, plus the UL-recognized sensor uses an LED to indicate CO shutoff or fault. Powerful Gasoline: 10,000 starting watts and 8000 running watts, propane: 9000 starting watts and 7200 running watts, natural gas: 8750 starting watts and 7000 running watts and engine oil is included. SPECIFICATIONS Portable Generator Technology : Tri Fuel, CO Shield Gasoline Starting Watts: 10000W Gasoline Running Watts: 8000W Propane Starting Watts: 9000W Propane Running Watts: 7200W Natural Gas Starting Watts: 8750W Natural Gas Running Watts: 7000W Gasoline Starting Amps at 120V: 83.3A Gasoline Starting Amps at 240V: 41.7A Gasoline Running Amps at 120V: 66.7A Gasoline Running Amps at 240V: 33.3A Propane Starting Amps at 120V: 75A Propane Starting Amps at 240V: 37.5A Propane Running Amps at 120V: 60A Propane Running Amps at 240V: 30A Natural Gas Starting Amps at 120V: 72.9A Natural Gas Starting Amps at 240V: 36.5A Natural Gas Running Amps at 120V: 58.3A Natural Gas Running Amps at 240V: 29.2A Volts: 120/240 Frequency: 60Hz Outlets: GFCI 120V 20A Duplex (5-20R) (2), 120V 30A Locking (L5-30R), 120/240V 30A (L14-30R) GFCI Outlets: Yes Covered Outlets: Yes Covered Circuit Breakers: Yes Gasoline Run Time at 1/2 Load: 12.5 h. Propane Run Time at 1/2 Load: 5 h. Noise Level: 74 dBA Parallel Capability: No DC Operation: No Voltmeter: Intelligauge Automatic Voltage Regulation: No Battery: Yes Start Type: Recoil, Electric Engine Brand: Champion Engine Size: 459cc Engine Type: 4-stroke Engine Speed: 3600 Fuel Type: Gasoline, Propane (LPG), Natural Gas (NG) Fuel Gauge: Yes Gasoline Capacity: 8.5 gal. Gasoline Tank Material: Steel Engine Oil Type: 10W-30 Engine Oil Capacity: 1.1 qt. Engine Oil Included: Yes Low Oil Shut-Off: Yes Wheels: Yes Wheel Type: Solid Wheel Diameter: 10 in. PGMA G300-2018 Compliant: Yes EPA Certified: Yes CARB Compliant: Yes DIMENSIONS Length: 27.6 in. Width: 28.2 in. Height: 26.0 in. Weight: 207.0 lb.
2.4 Inch 240x320 QVGA 14PIN SPI4 IPS 250nits TFT LCD Display Module EX02401-A01 is a 2.4 inch, IPS active matrix TFT LCD module with transmissive mode. The module dimension is 42.72(W)60.40(H)mm; active area 36.72(W)48.96(H) mm (2.4"diagonal). Its resolution is 240x320 pixels (width 240pixels x height 320 pixels) and every pixel is made up of three vertical strips of Red, Green and Blue dots. General Specifications of 2.4 Inch 240x320 QVGA 14PIN SPI4 IPS 250nits No. Item Specification 1 LCD size 2.4 inch 2 Resolution 240(RGB)320 3 Active area 36.72(W)48.96(H) 4 Module size 42.72(W)60.40(H)2.21(T)(Exclude FPC) 5 Viewing Direction All 6 Driver IC ST7789V 7 Polarizer Transmissive 8 Interface 4-SPI 9 Brightness 250cd/m2 10 Back Light White 11 Pixel arrangement RGB vertical stripe Outline Dimension of 2.4 Inch 240x320 QVGA 14PIN SPI4 IPS 250nits Features of 2.4 Inch 240x320 QVGA 14PIN SPI4 IPS 250nits The module features wide viewing angle thanks to the IPS panel which is one of the most popular techniques on the market now. This china 2.4 tft display module has built-in IC ST7789V supporting SPI interface. The brightness is 250 cd/m2 with contrast ratio 800:1. Operating temperature covers from -20~+70, storage temperature range is from -30~+80..This single-display module is suitable for use in industry, household appliances, toys and medical treatment,small consumer electronics and other fields. As one of the most professional 2.4 tft manufacturers, we provide china display tft lcd, 2.4 inch lcd china, china 2.4 inch lcd, china lcd panel, etc. For 2.4 inch lcd price or more information, please feel free to contact us!
EX02002-A01 is a 2.0inch, IPS TFT LCD module with transmissive mode. Its resolution is 480 360dots (480 vertical by 360 horizontal pixel) and every pixel is made up of three vertical strips of Red, Green and Blue dots. This miniature 2.0 inch TFT module has built-in IC ST7701S supporting MIPI serial interface. The brightness is 250 cd/m2 with contrast ratio 1000:1.Operating temperature covers from -20~+70, storage temperature range is from -30~+80.This single-display module is suitable for use in industry, household appliances, toys and medical treatment,etc. General Specifications of 2.0 Inch 480x360 HVGA 24PIN MIPI IPS 250nits No. Item Specification 1 LCD size 2.0inch 2 Resolution 480(RGB)360 3 Active area 40.8(W)30.6(H) 4 Module size 49.1(W)45.96(H)2.53(T)(Exclude FPC)mm 5 Interface MIPI1 6 Polarizer Transmissive 7 Brightness 250cd/m2 8 Pixel arrangement RGB vertical stripe 9 Back Light 450cd/m² 10 Viewing Direction All 11 Contrast Ratio 1000:1 As a professional china lcd module manufacturer, we provide china lcd display panel, dsi tft display, dsi tft, dsi lcd panel, mipi dsi lcd panel, mipi lcd panel, mipi tft, hvga lcd, hvga tft, etc. For more information, please feel free to contact us!
Model 4L126TIL Engine type 4 cycle, In line, direct- injection, water cooled with turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 545(401)/2,200 Displacement( cc ) 11,051 Cylinder number - bore x stroke( mm ) 6 - 123x 155 Mean piston speed (m/sec. ) 11.4 Compression ratio 16.7 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 114 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 7.0 Alternator capacity ( V- A ) 24 - 80 Battery (V- Ah) 24 - 150 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 42 / 39 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by V- belt Marine gear Model DMT240H (1.50 / 1.97 / 2.44 / 2.93 / 3.40), DMT260HL (3.53 / 4.08 / 4.52 / 5.04), DMTP6500 (5.11 / 5.62 / 5.91 / 6.57 / 6.95) Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) Marine Gear(DMT240H) without M/G mm 1,311 x 904 x 1153 with M. gear mm 2,031 x 904 x 1153 Engine dry weight without M/G kg 1,136 with M. gear kg 1,536
Model 4L126TIM Engine type 4 cycle, In line, direct- injection, water cooled with turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 495(364)/2,100 Displacement( cc ) 11,051 Cylinder number - bore x stroke( mm ) 6 - 123x 155 Mean piston speed (m/sec. ) 10.9 Compression ratio 16.7 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 102 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 7.0 Alternator capacity ( V- A ) 24 - 80 Battery (V- Ah) 24 - 150 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 42 / 39 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by V- belt Marine gear Model DMT240H (1.50 / 1.97 / 2.44 / 2.93 / 3.40), DMT260HL (3.53 / 4.08 / 4.52 / 5.04), DMTP6500 (5.11 / 5.62 / 5.91 / 6.57 / 6.95) Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) Marine Gear(DMT240H) without M/G mm 1,311 x 904 x 1153 with M. gear mm 2,031 x 904 x 1153 Engine dry weight without M/G kg 1,136 with M. gear kg 1,536
Model 4L126TIH Engine type 4 cycle, In line, direct- injection, water cooled with turbo charger & inter-cooler Rating output (B.H.P) PS(kW)/rpm 450(331)/2,000 Displacement( cc ) 11,051 Cylinder number - bore x stroke( mm ) 6 - 123x 155 Mean piston speed (m/sec. ) 10.3 Compression ratio 16.7 : 1 Firing order 1 â?? 5 â?? 3 â?? 6 â?? 2 â?? 4 Governor type of injection pump Mechanical all speed (R.S.V) Fuel consumption lit / h 88 Starting system Electric Starting by starter motor Starter motor capacity (V- kW ) 24 - 7.0 Alternator capacity ( V- A ) 24 - 80 Battery (V- Ah) 24 - 150 Cooling system Indirect sea water cooling with heat exchanger Cooling water capacity Max. / Min. lit 42 / 39 Fresh water pump type Centrifugal type, driven by V- belt Sea water pump type Rubber impeller type driven by V- belt Marine gear Model DMT240H (1.50 / 1.97 / 2.44 / 2.93 / 3.40), DMT260HL (3.53 / 4.08 / 4.52 / 5.04), DMTP6500 (5.11 / 5.62 / 5.91 / 6.57 / 6.95) Direction of revolution crankshaft Counter clockwise viewed from stern side propeller Clockwise viewed from stern side Engine size (L x W x H) Marine Gear(DMT240H) without M/G mm 1,311 x 904 x 1153 with M. gear mm 2,031 x 904 x 1153 Engine dry weight without M/G kg 1,136 with M. gear kg 1,536
Jet fuel A1 $84/$80 - 1m barrels. TANK TO VESSEL(TTV) TANK TO TANK(TTT) TRANSACTION PROCEDURE REFINERY FOB PROCEDURE ROTTERDAM & HOUSTON ONLY!. 1. Buyer issues official ICPO addressed to the refinery or representative with passport data page and certificate of incorporation. 2. Seller issues commercial invoice (CI), buyer signs and returns the signed invoice to the seller. 3. Seller issues to the buyer the partial proof of product documents (a) ATSC- Authority to sell and collect. (b) DTA- Dip Test Authorization. (c) Product Passport (d) Statement of product availability duly signed. (e) Commitment letter to supply duly signed. (f) ATV- Authority to verify the existence of product via email or phone call. (g) Certificate of Origin (h) US Attorney Escrow Account for Payment of Five days Tank Extension. 4. Buyer pays for the five days extension into the Seller's US attorney escrow account for the extension of sellers tanks. Seller confirms payment and notifies their tankfarm. 5. Buyer sends Dip test authorization to the seller tank farm for endorsement and receives TSR (for five days) including the full GPS coordinates of the tank, Hub Numbers, terminal access permit and dip test is conducted immediately with Buyer SGS report. Seller sends the properly endorsed NCNDA/IMFPA to all the intermediaries in the transaction. 6. After a successful dip test in seller tanks, Buyer take over the seller tank or seller inject into buyer's Vessel/Tank and buyer conducts its DIP TEST inspection for Q&Q of the Petroleum products aboard Vessel/Tank. 7. Buyer after a successful Q &Q Dip test on the product, the buyer makes the payment for the total value of the products injected into the Vessel/tanks through the means of MT103-TT. 8. Upon seller receives the payment for the products from the buyer, the seller issues to the buyer the title ownership of the product and all exporting documents of the product. 9. The seller pays all intermediaries involved in the transaction.
Aluminum sheet refers to a rectangular frame sheet made by rolling aluminum ingots. It can be pure aluminum sheet or aluminum alloy sheet. According to different application requirements, aluminum sheet can also be divided into different types such as thin aluminum sheet, medium thick aluminum sheet and pattern aluminum sheet. . Aluminum sheets have the characteristics of good light weight, corrosion resistance and thermal conductivity, so they are widely used in construction, automobile, aviation and other fields. The cross-section of the aluminum sheet is rectangular and the thickness is uniform, and when the thickness is greater than 0.2mm, it is usually delivered in a flat shape. Additionally, aluminum panels are often trimmed by shearing or sawing before delivery. Aluminum sheet uses: 1. Construction field. Aluminum panels are used to make building curtain walls, ceilings, interior and exterior wall decorations, etc. They have good fire protection and anti-corrosion properties and are suitable for exterior and interior decoration of high-rise buildings, commercial buildings, airport terminals, squares, stadiums and other buildings. 2. Transportation field. Aluminum sheets are used to make car bodies, roofs, windshield frames and other components. Because of their light weight and high strength, they help improve the fuel efficiency and safety of cars. 3. Electronic field. Aluminum sheets are used to make casings, heat sinks, circuit boards, etc. of electronic products. Due to their conductivity and corrosion resistance, aluminum circuit boards are widely used in electronic products. 4. Packaging field. Aluminum sheets are used to make food packaging, cosmetic packaging, etc., and have good moisture-proof, anti-oxidation, and fresh-keeping properties. 5. Aerospace field. Aluminum sheets are used to manufacture exterior panels, fuel tanks, boosters, etc. for aircraft, satellites, and other equipment. Because of their high strength, light weight, and corrosion resistance, aluminum materials have been widely used in the aerospace field. 6. Other fields. Aluminum sheets can also be used for mechanical parts processing, mold manufacturing, chemical pipeline wrapping, etc. Advantages of aluminum sheets: 1. Low density 2. Good electrical and thermal conductivity 3. Uniform coating and various colors 4. Easy to process 5. Strong corrosion resistance
JOYMORE-7 Passenger Elevator JOYMORE-7 machine roomless residential passenger elevator provides users with a safe, comfortable, energy-saving, and environmentally friendly product experience. Features of JOYMORE-7 Residential Passenger Lifts Level-A Energy Efficiency Certification. Standby Energy Saving Technology. Energy Regeneration System (Optional). Specification Of JOYMORE-7 Passenger Elevator NO. Specification 450 630 800 1050 1 Capacity (kg) 450 630 800 1050 2 Speed (m/s) 1 1.6 1 1.6 1.75 1 1.6 1.75 1 3 Operation System full collective selection operation 4 Driving System VVVF 5 Door Operator System VVVF 6 Traction Machine Permanent Magnet Synchronous Gearless type 7 Control System CTRL80 8 Wide Car1 Car Dimension mm - 1100*1400 1350*1400 1400*1600 width*depth Shaft Size mm - 1770*1800 1920*1800 2000*2000 W*H 9 Deep Car1 Car Dimension mm - - - 1100*2100 width*depth Shaft Size mm - - - 1800*2500 W*H 10 Deep Car2 Car Dimension mm 1000*1200 1100*1400 1350*1400 1100*2100 width*depth Shaft Size mm 1570*1600 1670*1800 1920*1800 1700*2500 W*H As a reliable ife elevators co ltd, we can provide kinds of elevators for sale, anything you need, please contact us.
Complete Automatic Aluminum Foil Container Making Machine Line Model: SEAC-55AS Units: Automatic Feeder+Automatic55Ton Press+Cavities Mould+Auto Stacker+Scrap Sucker & Auto Presser. It fit for all common size Aluminum Foil Container production requested. The Big capacity could to cover big range of size products. Lower power requested than other old model machines. Specification: 1. Raw material: Aluminum foil; Thickness: 0.030mm ~0.250mm; Alloy: 8011, 8006, 3003, 3005; Temper O to H24; 2. Good Japan's Inverter, PLC and 10inch Touch Screen control system; 3. Max. Width of Aluminum foil: 600mm; 4. Max. Diameter of Aluminum foil: 700mm; 5. Core diameter of Aluminum foil: 76mm(152mm as Optional ); 6. Working speed: 40-75 times/min; 7. Total Power: 13kw; 8. Compressed air needed: 0.5- 0.8 Mpa, 0.2m3/min; 9. Install dimension: 6100*2600*3200mm; Technical Data: Max. Mould Size:L700*800*420mm; Slide block stroke: 120-200mm (Standard: 180mm); Automatic mould adjust unit: 0.5kw; Work plate dimension: 700*950mm; Mould handle hole dimension: 50*60mm(Diameter*Depth); Power: 3P, 380/220V, 50/60Hz; Net weight: 6000kg. SEAC-55AS is two cavities capacity for Aluminum foil container production now, it have instead of the old 40Ton model, as it is more big capacity to cover container size! Complete automatic level upgrade your factory capacity, lead your company be higher level competition and situation.
Complete Automatic Aluminum Foil Container Making Machine Line Model: SEAC-63A-4 : Max. Mould Lenght 1150mm Units: Automatic Feeder+Automatic 63Ton Press+Cavities Mould+Auto Stacker+Scrap Sucker& Presser. It fit for all common size Aluminum Foil Container production requested. The Big capacity could to cover big range of size products. Lower power requested than other old model machines. Specification: 1. Raw material: Aluminum foil; Thickness: 0.030mm~0.250mm; Alloy: 8011, 8006, 3003, 3005 etc.; 2. Japan Inverter, PLC and 10inch touch screen control system; 3. Max. Width of Aluminum foil: 880mm; 4. Max. Diameter of Aluminum foil: 1000mm; 5. Core diameter of Aluminum foil: 76/152mm; 6. Working speed: 40-75 times/min; 7. Total Power: 11kw+2kw+2kw+1kw; 4Motor 8. Compressed air needed: 0.5- 0.8 Mpa, 0.2m3/min; 9. Install dimension: 7100*2600*3500mm; Technical Data: Max. Mould Size: 1100*900*450mm; Slide block stroke: 180-260mm; Slide block dimension: 380*145mm; Automatic mould height adjust unit: 0.5kw; Work plate dimension: 1100*200*300mm, separated two sets with Balls; Tension: complete automatic adjust; Feeding System: Servo Motor, higher precision and more power; Auto Stacker: SMC lift for stacking system, top quality; Power: 4P, 380V or 220V, 50Hz /60Hz; Net weight: 9,500kg.
Product overview It is a mixture of polymer and surface active agent. This agent is a high-efficiency deposit control agent and repulping auxiliary agent that can be used directly on paper, paperboard and pulping systems, so as to control various deposits. Regardless of whether the sediment is derived from resin, broken paper or secondary fibers, it is an excellent cleaning agent. This product is suitable for neutral, acidic, and alkaline systems. It can prevent the resin, viscose, paint stickies and other wet hydrophobic pollutants from being accumulated in the paper and pulp machine felts, thereby making the felts clearer, the paper more efficiently, and the service life of the felts longer. Technical specifications �· Appearance: Light yellow liquid �· Density: 0.88-0.95 g/cm3 �· pH value (10% of water solution): 6-10 �· Solubility: Completely soluble in water, but insoluble in most organic solvents Performance characteristics 1. Improve the operating stability of the squeezing section 2. Prevent the hydrophobic pollutants such as resin and viscose being accumulated on the paper machine felt 3. It can keep the uniformity of the air permeability of the blanket for a long time, and makes the blanket's service life longer 4. Improve product quality and reduce unplanned shutdown time to clean blankets 5. It can frequently utilize secondary fibers and enhance economic benefits. Usage tips The amount can be varied from the paper types. The recommended dosage is 4-10 ml/min/m of fabric or roll width. The low-pressure spray water can be used to spray the forming net and coarse calico paper surface. Packing and storage This product is packed in plastic buckets, 200kg or 1000kg of per plastic buckets. This product shall be stored in a shaded, cool and dry condition at room temperature, shelf life: 6 months. This product is not dangerous.
Biesse Part No.: 1705A0123 1705A0123 tool holder clips Biesse tool holder (white fork) HSK F63 Biesse HSK 63F tool clips Biesse Rover tool holders Biesse CNC tool gripper HSK63F Biesse HSK 63F plastic tool fork Biesse tool collet HSK F63 1705A0123 HSK F63 Tool Holder Clips for Biesse Rover CNC This Biesse 1705A0123 spare part is the consumable of Biesse Rover CNC. HSK 63F tool fork is for the HSK63F tool holder clamping, used with carousel or side loading tool changer. HSK63F Tool Holder Forks Specifications: 1. Made in China, famous brand 2. Imported USA Dupont white plastic material, high quality, reinforced and anti-explosion. 3. The tool holder clips are resistant to the temperature changes and maintain very precise clutch tolerance. 4. Alloy steel block casting inside, reinforced structure, has high loading capacity, also with steel positioning pins. 4. Dynamic balance grade: G2.5, 30000rpm 5. Yaw precision: 0.005mm 6. Loading capacity: 8-10kgs 7. Last more than 60,000 times tool changing cycles. We have tested. 8. The same material as Italy fork used. The outlook is up to 95% same as Italy made. Lifetime can up to more than 90% of Italy made. 1705A0123 HSK63 plastic grippers are available in stock for quick delivery. Molded plastic with metal insert for rigidity and locking pin for aggregates also are available here. Beside used on Biesse Rover CNC machines, these tool changer grippers are also widely used on CNT Motion, CR Onsrud, DMS, Flexicam, Multicam, Northwood, Techno, Laguna, Thermwood, Bulleri, ITALMAC Zeus, KDT, Masterwood auto tool changer CNC router machines. They are an exact interchange tool holder gripper.
3.Technical Parameter: Model and specification :DL9930 Drop height: 10-1500mm, any setting Steel ball weights :55g, 64g, 110g, 225g, 535g (optional upon request) The maximum size of the test piece is :400 * 350mm Height display method: Graduated scale display (electrically selectable with LCD or touch screen control display) Drop height error :â?¤ �± 2mm Drop method: electromagnetic adsorption drop Control and lifting methods: Electric control electromagnet, manual lifting of electromagnet fixing rod (electric lifting using motor) Protective cage :around the protective device Sample fixation method: fixture clamping and fixation Drop bottom plate size :500 * 400 * 10mm Overall dimensions of the testing machine :500 * 400 * 1800mm Control box overall size :300 �? 370�? 1060mm Motor power: 0.4KW (electric) The net weight of the equipment is :approximately 40kg Power supply:AC220V/50Hz 5.Configuration List 1. Main purpose: The falling ball impact testing machine is suitable for testing the impact strength of plastic, ceramics, acrylic, glass, lenses, hardware and other products. 2.Product features: DC electromagnetic control mode is adopted to place the steel ball under the electromagnetic chuck and the steel ball is automatically sucked up. Press the drop key, the magnet releases the steel ball instantly, and the steel ball will conduct Free fall test to accurately impact the surface of the test piece; The drop height can be adjusted up and down, and there is a height scale attached (the electric series can directly display the test height) to determine the drop height of the component. Equipped with a laser positioning device, the impact testing position can be accurately aligned with the laser, resulting in more accurate testing results. Compliant with standards Test standards: JIS R3205:1989, ISO/DIS125421 12543-6:1997 AS/NZS2208:1996, GB/T9962-1999.
K-LFP48100S is a new type of intelligent battery pack developed by KODU Technology, with built-in cell balance, and a smart monitoring system. It is suitable for the installation of 19-inch cabinets. Intelligent design: intelligent detection, SOC&SOH management, simplified O&M, and self-management. Intelligent collaboration: With the intelligent power system to realize intelligent features (such as intelligent voltage boosting and intelligent hybrid use). Intelligent anti-theft design:Intelligent software lock, displacement lock, and buzzer alarm. High reliability design: integrated BMS design, long service life. Multiple lithium batteries are used in parallel to meet the application requirements of large-capacity sites; Support remote power supply, constant voltage 57V discharge; Energy storage - peak cutting and valley filling; K-LFP48100S has high-energy density, redundant safety design, long life, light weight, easy installation, maintenance-free, remote monitoring Nominal voltage 48V Nominal capacity(25 ,0.5C) 100Ah Nominal energy 25 ,0.5C 4800Wh Weight 40±0.3Kg Cell-positive material LiFePO4 Combination mode 15S1P Dimensions (W * D * H) 443mm*400mm*135.5mm Communication interface RS485&CAN; 2 dry contacts IP rating IP20 Shell material Steel plate baking varnish Cycle life(0.5C, 25 ) 6000 times @80% DOD Design life(25 ) 15 years LED Display Alarm/Run/SOC Electrical parameter Operating voltage 42V-57.6V Maximum charging current (25 ) 100A Maximum discharging current (25 ) 100A Standard charging current (25 ) 50A Standard discharging current (25 ) 50A Recommended charging voltage 54V Discharge cut-off voltage 42V Battery input protection BMS Efficiency 98% Self discharge (25 ) Less than 5% after 90 days storage Internal resistance 40m�© Maximum number of parallels 32 Protection function Overvoltage protection, overcurrent protection, low-voltage protection, over temperature protection, low temperature protection, reverse connection protection, short circuit protection Environment Charging temperature-40~60 (Optional heating film) 0~60 Discharging temperature-20~60 Storage temperature-10 ~45 Relative humidity 5%~95%(non condensing
2040/1530 thin mild steel sheet CNC plasma table cutting machine is especially designed for thin steel plate ( 0-3 mm )fast cutting. It adopts cylinder compacting system to prevent steel plate moving during cutting. It has a very fast cutting speed for the thin plate. 2040 1530 thin mild steel sheet CNC plasma table cutting machine features: 1. The beam uses light structural design, with good rigidity structure, light deadweight and small movement inertia. 2. STARFIRE control system, the file incision and export automatic correction , real-time tracking detection of plasma power in the process of cutting current. The control system uses the U-disk exchange processing document, easy to operate. 3. Z axis adopts Cylinder pressure, so high precision and long life time using are assured. 4. It can apply to iron sheet, the aluminum sheet, the galvanized sheet, hundred steel plates , metal plates and so on. Equipped with other metal equipment, forming the advertising word processing tubeline. Completely solve the traditional manual processing methods. Improve the efficiency of several times. 5. Cutting kerf is small, tidy, and avoid a second dressing processing. 6. High cutting speed, high precision, and low cost and cheap. 7. Support FASTCAM, Astronautics Haire, ARTCAM software, Type3 produce standard G code way document, also can change software to read AUTOCAD software produce DXF form documents. Applicable Materials: Especially for all kinds of metal materials such as steel, copper, aluminum and stainless steel that thickness less than 8mm cutting. 2040 1530 thin mild steel sheet CNC plasma table cutting machine parameters: Model RB 1560 2040 Working area (X-Y) 1500mm*6000mm, 2000mm*4000mm Working material Iron, Steel, Aluminum, sheets, Galvanized, sheets. Titanium, Plates Working Thickness 0-8mm Cutting Speed 0-12000mm/min Power 8.5kw Input Voltage 380V 50HZ/60HZ Plasma Current 63A Connecting Way USB Working Mode Untouched arc striking Cooling method With water pump and tank provide circulating water cooling Rail guide HIWIN square rails Transmit way Taiwan imported ball screw Operation language Chinese or English Command G code, *uoo, *mmg, *plt Optional power source America HYPERTHERM or China HUAYUAN Spare parts Electrode ,Electricity nozzle and Water jacket
1. Raw materials: Our edge banding use high quality PVC and ABS as raw materials. Imported PVC particles comply with environmental protection standards, high purity, without any other materials, and it is also more environmentally friendly. 2. Clear texture: We are now using four color printing process by single extrusion which is more different from normal transfer printing process. It can make clear texture and looks like real wood edge banding. 3.Good abrasion resistance: All of our edge band surfaces have UV, it has high color stability, no easy to fade, anti detergent. So, cleaning agent can be used. 4. Color stable: Chuangxing's edge banding is not easy to fade. It's made of pure raw material, with scientific formula and according to the SGS standard. 5. Accurate size: Chuangxing's edge banding is produced by the imported professional assembly line, with stable quality. It won't affect the processing or use due to the size deviation. 6. Colorful design: Chuangxing matches colors by computer system, we focus on keeping same color after trim, now we have more than 400 colors of copper plates available. 7. Good flexibility: Even on a small plate with bending radius, our edge banding won't have wood grain fracture. 8. Stable expansion: the size stability of our edge banding is good, there won't be any excessive shrinkage or expansion due to a large temperature difference. 9. Small glue-line: Our edge banding is in the shape of internal bending, the hot-melt glue-line is the smallest after sealing, the appearance performance is better, and the moisture resistance will be the largest satisfied while the dust is prevented from entering. 10. The back coating of our edge banding has fluorescent agent, it can glimmer under the currency detector, so it's convenient for customer to identify. 11. Easy to processing: Our back coating is suitable for all kinds of hot-melt, so we can ensure not easy to fall and the bending will be more solid. 12.Good practical performance: Our edge banding can be uniform in thickness, smooth surface, clear texture, base color and print color, without any white appearance while trimming or bending.The bottom glue also has good effect, it has low requirement of sealing temperature, so that sealing can be more convenient and quick.
At GB FUTURE TRADING, we offer a diverse selection of premium fresh fish, sourced directly from the pristine waters of Egypt and Morocco. Our fresh fish selection is meticulously curated to ensure the highest standards of quality, freshness, and taste. Hereâ??s a detailed description of what we provide: 1. Variety of Fish: Our range includes popular varieties such as sea bass, sea bream, mullet, sardines, and mackerel. Each type of fish is chosen for its superior flavor and texture, catering to both gourmet restaurants and home cooks. 2. Sourcing and Sustainability: We prioritize sustainable fishing practices and source our fish from trusted fisheries that follow stringent environmental guidelines. This commitment helps to maintain healthy fish populations and protect marine ecosystems. 3. Quality Assurance: Every fish is inspected for quality and freshness before being dispatched. We utilize state-of-the-art refrigeration techniques to maintain the fish at optimal temperatures during transit, ensuring that they arrive at their destination as fresh as the moment they were caught. 4. Packaging: Our fresh fish is expertly cleaned, scaled, and packaged to preserve its freshness and nutritional value. The packaging is designed to be leak-proof and temperature-controlled, making it ideal for both retail and wholesale markets. 5. Delivery and Distribution: We offer efficient and timely delivery services, ensuring that our fresh fish reaches our customers promptly. Whether you are a small business or a large supermarket chain, we have the logistical capabilities to meet your needs. By choosing GB FUTURE TRADING, you are assured of receiving the freshest and highest-quality fish available. Our dedication to excellence, sustainability, and customer satisfaction sets us apart as a leading supplier in the seafood industry.
High quality single tag printe ribbons reinforced wear-resistant label printer enhanced hanging tag printer ribbons barcode paper label paper 2023 Hot Sale New Arrival Wax Resin Thermal Transfer Printer Ribbons for Barcode Printer Heat transfer printing ribbons have a wide range of applications and high-speed printing capabilities Excellent image durability, excellent wear resistance, corrosion resistance, and heat resistance Product features: 1.Excellent high-quality and high-speed printing performance. 2.Excellent wear resistance, heat resistance, corrosion resistance, and durability. 3.The label has a wide range of adaptability and meets various demanding environmental requirements. 4.High sensitivity ensures excellent image printing results. 5.The anti-static coating on the back can effectively protect the print head. 6.Applicable substrates: water washed standard materials, fabrics, nylon standards, acetate fibers, etc. Product specifications: Basic maximum width: 100%; a: 40, 60, 70, 80, 90, 110, 130, 170 mm Basic length: 210m, 300m, 450m Carbon tape rolling direction: outer carbon, inner carbon Carbon belt hub: 1 inch, 1/2 inch Shaft bayonet: 180 �° bayonet Note: Carbon belts of different sizes and colors can be customized according to your needs. if you need other specifications, please consult us!+86-13924290301 w w w . d h m t t . c o m sales@g z d h m . c n Printer Consumable-Toner, Ink and Ribbon Cartridges Satin ribbon Ricoh thermal transfer ribbon Ink ribbon printing Manufacturer of standard and custom resin and wax ribbons thermal transfer printer ribbons manufacturer of ribbon Ribbons resists scratching, smearing, flaking, and ultraviolet rays Distributor of printer ribbons Wax and resin thermal transfer ribbons types of ribbon participation ribbon rhinestone ribbon grosgrain ribbon decorative ribbon christmas ribbon wholesale ribbon lavender ribbon custom ribbon organza ribbon halloween ribbon miscarriage ribbon Single tag printer, zx40 ribbon printer, printer ribbon cartridge, digital ribbon printer, brother ribbon printer, thermal printer ribbon, label printer ribbon, satin ribbon printer, epson ribbon printer, zebra printer ribbon, ink ribbon printer, barcode printer ribbon, ribbon out
ECO PELLET 100% Pure Beech Weight: 15 kg Source: Processing waste Yield: Very high Ashes: Minimal Binders: None Residues: Moisture: 4.1% (UNI CEN/TS 14774-2:2005) Ashes: 0.5% (UNI CEN/TS 14775:2005) Analysis: Mechanical durability: 95.8% (UNI EN/TS 1602:2010) Apparent bulk density: 646 kg/m�³ (UNI CEN/TS 15103-1:2005) Fine particles: 0.8% (UNI EN/TS 15210-1:2006) Physical, Chemical, and Physico-Chemical Parameters: Lower heating value: 4488 kcal/kg (UNI CEN/TS 14918:2005) Lower heating value: 18.76 MJ/kg (UNI CEN/TS 14918:2005) Higher heating value: 4777 kcal/kg (UNI CEN/TS 14918:2005) Higher heating value: 19.95 MJ/kg (UNI CEN/TS 14918:2005) Here are some key features of our beech pellets: 1. Superior Quality: Our beech pellets are made from 100% pure beech wood, ensuring a clean burn and maximum heat output. 2. Sustainable Sourcing: We obtain our beech wood from responsibly managed forests, promoting sustainable forestry practices and minimizing our environmental footprint. 3. High Energy Efficiency: Our pellets have a low moisture content and a high calorific value, guaranteeing efficient combustion and reduced emissions. 4. Consistency and Reliability: We employ strict quality control measures to ensure uniform pellet size, density, and moisture content, providing consistent performance and reliable supply. 5. Packaging and Delivery: We offer flexible packaging options tailored to your specific requirements, along with timely delivery to your desired location.
