Rebar Production Line Role Steel 6mm Production Steel Bar 12 meter long Diameter 6mm to 42mm 300Hz, 3700V, 6*1250V
Cold Rolled Ribbed Rebar machine This cold rolled ribbed rebar machine is a kind of steel roll forming machine for processing Grad Q235 hot-rolled round bar to 3 side ribbed steel equipment. The cold rolled ribbed rebar machine is main part of cold rolled ribbed steel bar production line. 3 ribbed steel bar can be used for bridge engineering, houses construction, high-rise buildings and other industry. It can reduce costs and save about 40% steel. Tensile strength and yield strength of steel bar is reinforced. Cold rolling mill can roll the base metal into three-side thread steel bar which can reach 550 Mpa National Standard (GBT13788). Equipment advantages: high degree of automation,sophisticated manufacturing process, high output, long serving life, easy to operate and maintenance. Technical Parameter ModelMain motor KWDeputy motor KWShift capacity TZJ130 5-722-305.56-10ZJ150 5-9455.513-25ZJ1505-1255-757.530-45
Basalt fiber rebar high-strength non-metallic composite reinforcement made of basalt fibers, which is not exposed to water and salt. RBC types (diameters) 4mm, 6mm, 7 mm, 8mm, 10mm, 12mm, 14mm, 16mm, 18mm, 20mm, 22mm, 24mm. Resistant to corrosion Basalt armature perfectly resists corrosion, which in the future will not break the integrity of concrete elements. In addition to this, it does not change its original properties even under the influence of severe conditions. Lightness It is lighter relative to steel by 80%. Due to the low density, reinforcement on the basis of the composite is 5 times lighter than steel and almost 2 times heavier than water. Under the same strength conditions, the weight is 9 times less than steel. This significantly minimizes the cost of transportation, loading, unloading and general construction work. High strength Basalt reinforcements are 100% stronger than its counterparts. This is proved by the gap indicator, which is 2 times higher than that of the brand A III. Consequently, the estimated area will be much smaller. Cost effective By purchasing composite reinforcement, you can significantly reduce financial costs in construction. With Basalt - you have more materials for less payment.
Model Voltage Wattage Machine Cutting Max Min Machine size(mm) weight speed rebar rebar RC-16 220V/110V 690W/900W 8kg 2.5-3.0s 16mm 4mm 460*270*115 RC-20 220V/110V 950W/1250W 13kg 3.0-3.5s 20mm 4mm 410*115*220 RC-22 220V/110V 1000W/1250W 15kg 3.5-4.5s 22mm 4mm 420*120*230 RC-25 220V/110V 1600W/1700W 24.5kg 3.5-4.5s 25mm 4mm 480*150*255 RC-32 220V/110V 2200W 35KG 5s 32mm 6mm 550*180*270 NRC-20 220V/110V 950W/1300W 12.5kg 3.0-3.5s 20mm 4mm 500*130*140
Rebar Bending Machine
The parameters of standard Upsetting couplers : Size 16 18 20 22 25 28 32 36 40 Material of the rebar coupler is No.45 steel.
Rebar Coupler The splicing couplers model is divided into 9 categories according to the Rebar Coupler. (Unit: mm) 1).The parameter of couplers Size(mm) O D�±0.5ï¼?mmï¼? Threadï¼?mmï¼? L�±0.5 (mm) Pitch Rib peeling coupler weight/pc (kg) Thread Angle �¦16 25 M16.5 40 2.0 0.111 60 Degree �¦18 28 M18.5 45 2.5 0.136 �¦20 31 M20.5 50 0.175 �¦22 33 M22.5 55 0.203 �¦25 37 M25.5 60 0.266 �¦28 41 M28.6 70 3.0 0.375 2).The Characteristics of the Usage Mode usage occasion Standard Model used in the occasion for connecting the steel bar in normal situation Different Diameter Model used for connecting the steel bar in different diameters Flared Model used for the steel bar which was hard to match Positive And Negative Screw Thread Model Used in the occasion when the steel bar in the two sides both can not be turned but the lengths can be adjusted. Locking Nut Model Used when the steel bar can not be turned, then it turns the splicing coupler to join the steel bar and then lock the splicing coupler with the locking nut. 3).The material of the splicing coupler The material of the splicing coupler is constructional quality steel of No.45 steel.
Rebar Cold Extrusion Technology The Cold Extrusion Machine is made up by a hydraulic Clampy with Cold Pressing Dies and Hydraulic Oil Pump.� Only 1 â?? 3 kw power of oil pump, which is not limited by power capacity, has flexible structure and suitable for operation on several machines. Advantages: No professional and experienced worker needed, able to connect changed steel bar of different diameters. Save 80% of connector steel consumption. Only needs 1 3m to stamp each connector, which is about ten times faster than ordinary welding. No flammable gases, not affected by rainy or cold weather. Relieve congestion of the connecting point, facilitated concrete pouring.
1.Place it well at the working point. 2.Directly use it to press connection point with screwless couplers to link the two rebar.
Automatic Stirrup Bending Machine Works With Raw Metarial Coil Type of Wire Ribbed & Smooth Production Capacity (mm) Singlewire: 10-12 / Doublewire: 6-8 Max. Bending Opportunity CW and CCW/Birectional Rated Power 2 Servomotor 7,5 + 5,5 KW Driving Motor 7,5 KW (servo motor) Bending Motor Power 5,5 KW (servo motor) Length Tolerance ± 1 mm Bending Tolerance ± 1 Driving Speed 90m/minutes Bending Speed 1200 / sec. Pre-Strainghtening Unit X and Y Axis With multiple rollers Control Unit Operator sensitive/friendly program, Shapes can be easily created helping with angles and length by operator. The program was written by Sew engineers. Driving Unit Industrial type gearbox by EMPO Bending Unit Industrial type gearbox by EMPO Cutting Heav type industrial gear box Averageair - compressed consumption 6H/min Average - electric power consumption 4-6/Kw/h Compressor Needed 200lt/min Working Pressure (bar) 6 Bar Voltage 380v-50Hz-3Fhaze Switch - Sensors Proximith Switches Encoder 1024 Pulse/Sick Brand Driving Gear Box 2379 Grade With Heat Treatment Control Panel Type LCD 18 Machine Dimensions (W x L x H) 1500mm x 4600mm x 1900mm Machine Weight 2700 Kg Control Program Language TR, ENG, FR, ARAB
Automatic Stirrup Bending Machine Works With Raw Metarial Coil Type of Wire Ribbed & Smooth Production Capacity (mm) Singlewire: CW/Birectional Rated Power 2 Servomotor 7,5 + 5,5 KW Driving Motor 7,5 KW (servo motor) Bending Motor Power 5,5 KW (servo motor) Length Tolerance ± 1 mm Bending Tolerance ± 1 Driving Speed 90m/minutes Bending Speed 1200 / sec. Pre-Strainghtening Unit X and Y Axis With multiple rollers Control Unit Operator sensitive/friendly program, Shapes can be easily created helping with angles and length by operator. The program was written by Sew engineers. Driving Unit Industrial type gearbox by EMPO Bending Unit Industrial type gearbox by EMPO Cutting Heav type industrial gear box Averageair - compressed consumption 6H/min Average - electric power consumption 4-6/Kw/h Compressor Needed 200lt/min Working Pressure (bar) 6 Bar Voltage 380v-50Hz-3Fhaze Switch - Sensors Proximith Switches Encoder 1024 Pulse/Sick Brand Driving Gear Box 2379 Grade With Heat Treatment Control Panel Type LCD 18 Machine Dimensions (W x L x H) 1500mm x 4600mm x 1900mm Machine Weight 2700 Kg Control Program Language TR, ENG, FR, ARAB
Casing with a separate power supply unit power supply of hydraulic tools to squeeze on steel. The final connection ensures a tensile strength of at least 125% of the nominal yield strength of the reinforcement grade 500 MPa.
Rebar safety caps are made of premium quality plastic, which is sturdy, durable and not easy to break. It can stay under all harsh weather conditions. End caps for rebar stakes can be snap in to and install easily. They can prevent injuries and protect the rebar pieces from damage. The highly visible color can be easily spotted on to avoid injury. Rebar safety caps are perfect to use in construction sites and for workplace protection. The Rebar Safety Cap comes in a pack of 100.
Poultry products like duck eggs, duckling, chicken meat.
Name:Portable rebar bender/pipe bender Type:Rb-25 Voltage:220v/110v Wattage:1600w/1700w Gross weight:109kg Net weight:91kg Bending angle:0-180 Max.Rebar25mm Min.Rebar6mm Package:One pc/ cardboard ctn/metal box Carton size:500x555x505mm Machine size:450x500x440mm Certificate:Ce rohs Use : it can preset angle locks for repeating the same angle bend. The two slide-type angle selectors(point1/point2) can be set to accurately bend any angle from 0-180. The two standard foot pedal control switch for hands - free bending. Package:One pc/ cardboard ctn/metal box Carton size:500x555x505mm
Long Pun rebar bending machine is manufactured and modified in Singapore. This machine is powered either by diesel engine/motor. It is easy to operate, can be manually adjusted to bend from 0 to 180 degrees. Product has gone through extensive redesigning and modification and is built to last. Safety features will all be included and assembled before delivery Machine comes with a 1 year warranty from manufacturer defect.
1.Adopt thread cold rolling technology, no cutting of rebar parent metal, the strength of threaded end is higher than its parent metal. 2.With spiral lead angle technology, easy to roll thread and ensure higher thread accuracy. 3.Rib peeling device adopts automatic opening-closing mechanism. With high efficiency, need only 20 seconds to finish a threaded end. 4.Be able to process rebar sizes 14-40mm, and max. thread length is 120mm for 16-32mm rebar, and 100mm length for 36-40mm rebar with 7.5kw electric motor. 5.The updated version of AGS-40C and AGS-40Z, the wheelbase and shaft diameter of reducer is bigger than AGS-40 and 40E, so that the machine length is longer than AGS-40C. 6.The height of electric motor and reducer is lower than before, so that it could reduce the center of gravity of the whole machine. 7. Equipped with air compressor. 8. There are 2 machine heads for AGS-50D, 1 is for 14-40mm, and the other for 50mm rebar screw.
Features 1. Hydraulic full-automatic, fast speed. 2. Cutting thread on forged bar with chaser, threading diameter 16-40mm(upsetting M20-M45mm). 3. Strength of the joint is higher than the rebar material. 4. Thread is full enough, max. threading length is 150mm. 6. Thread pitch is from 2.0 to 4.5mm with high accuracy.
CNC Stirrup Bender can fully suit to bend various diameters of stirrup, it is manufactured from Qingdao Dongfeihong Intelligent Technology Co., Ltd. Our company imported advanced technology and research to design this machine. The machine is professional for bending two steel bars at the same time. Our CNC stirrup bender is a fully automatic stirrup processing equipment which integrates straightening, bending and cutting etc. The CNC stirrup bender adopts servo motor and top brand PLC intelligent control, can effectively bend steel bar precisely. It also saves workers just with one or two on site.
CNC Stirrup Bender can fully suit to bend various diameters of stirrup, it is manufactured from Qingdao Dongfeihong Intelligent Technology Co., Ltd. Our company imported advanced technology and research to design this machine. The machine is professional for bending two steel bars at the same time. Our CNC stirrup bender is a fully automatic stirrup processing equipment which integrates straightening, bending and cutting etc. The CNC stirrup bender adopts servo motor and top brand PLC intelligent control, can effectively bend steel bar precisely. It also saves workers just with one or two on site.
