Working principle: Air flotation is a liquid-solid separating process in wastewater treatment. When particle formed in water as suspended solid, namely raw water contains fabric, sand, sludge and other solid or dissolving type water or becomes like gels after chemincal and physical treatment had transfer to suspended solid, is adhered and wraped by sufficient fine air bubble, specific gravity of particle is smaller than that of water that access to liquid-solid separation. Application: - For paper mill, be used to reclain the white water from paper machine, fibre from medium stage wastewater and lignin from black liquid. - Liquid- solid separation for emulsified liquid and oil wastewater from machenical or petroleum industry - Painting desposal and Printin and dying wastewater treatment from Auto industry or other fields. - Pre-treatment for slaughter and food industry - Liquid-solid separation for agent dosage of non-degradation by biological roganic - Liquid-solid separation of chemical process for electroplating wastewater or sewage containing heavy metal ion - Water treatment for urban running water or protable water. - Liquid-solid separation and sludge thicken for excess sludge during the wastewater treatment process Manufacture feature : (I) Floating upward tank uses reinforced concrete structure; its main equipments are as following: 1. Dissolved gases system: 1) Centrifugal pump unit: pressure pump of dissolved gases water, water circulating pump, the pressure value is about 0.3 MPa¡«0.35 MPa; 2) Dissolved gases tub: working pressure of the tub is 0.30-0.33 MPa (material:Q235A) (accompanied by pressure gauge and USERPage - 3 -4/20/2012water leveler); 3) High efficient gas jet unit: working jet equipment and circulating air adding jet equipment unit installed in the tub (material quality is 1Crl8Ni9Ti); 4) Vacuum air intake valve; 2. Water relief and collecting system: 1) Relief and mixing device of raw water and dissolved gases; 2) Water level adjusting device of floating upward tank in water collecting plant; 3. Stirring machine: (used for slag floating and air releasing) equipped with stirring device, electric motor and speed reducer. 4. Slag eliminator: equipment used to eliminate floating particles. 5. Electric control system: Power Distribution Cabinet (control working pump, circulation pump, stock pump, stirring machine, and slag eliminator). (II) For the engineering that water quantity used is relative small adopts steel integrated structure, it can be applied after that all equipments are installed, corollary equipment are complete, and the electric power source is linked.
HPT612-W is full sealed submersible level sensor. It is made by building in high stable and reliable piezo-resistive silicon pressure sensor and high accurate circuit board into the stainless steel housing. Integrated construction and standard signal provide the user easy and convenient application in the local working place. The special cable connects with housing, can be immerged into the media for a long time. HPT612-W level sensor has smart structure, high accuracy and good stability; it can be used for water or liquid measure and control of medicine, metallurgy, electricity, mine, city water supply and drainage and hydrology, etc. HPT612-W level transmitters is based on Zigbee wireless protocol and max transfer distance up to 400 meters, if add a wireless signal router, distance up to 800 meters. Characters: Accuracy: �±0.25%F.S. Wide working temperature scope Double supply by battery&DC power User-defined data transfer interval time With English level monitor PC software Highly-efficient lighting absorption and strong RFI & EMI resistance Remote signal transfer by Zigbee. 1.5 times range standard overload. 3 times range burst pressure CE approving Applications: well depth measurement and control water tank level measurement river level measurement and control wireless level monitor system Industrial course testing and control Building water supply systems Oil and Fuel Tank level measuring Automatic detection system Saving water to irrigate Liquid pressure and level measurement And so on
BOMB CALORIBomb CalorimeterMETER (FULLY AUTOMATIC) NEW MODEL "ALTIS" ALTIS Make fully Automatic Bomb Calorimeter are widely used for determining gross calorific values of liquid and solid samples, Automatically, User dosent need to make any manual calculations, all calculations are done automatically by the system itself & then are Automatically displayed, printed & transferred to PC. Automatically displayed, printed & transferred to PC. All the process is done by highly intelligent microprocessor program. The controllers are specially designed & manufactured to achieve best possible measuring accuracy desired by the users. FEATURE: a) Microprocessor Based. b) Automatically measuring and calculating of calorific value/water equivalent. c) Big LCD Display. d) In built printer. e) 16 soft-touch keypad. f) Weight of tablet feedable. g) Water equivalent feedable. h) Full test report printout with date and time. i) Temperature scanning resolution of 0.010 C j) Alarm on firing & after the test completes. k) Sensor open detection. l) No paper or printout door open detection. m) User interaction messages on LCD. n) Type of test selectable. o) Memory storage for data. p) Real time clock. q) Internal data logger with computer interface. r) PC software for data record. s) Soft power ON for full system.
Zebung chemical transfer hoses were developed to be a more flexible chemical hose that could handle 98% of all chemicals including solvents and corrosive liquids for pressure and suction service. These hoses are suitable for tank trucks, barges, ships or storage tank transfer for a variety of chemical materials. The clear UHMW PE tube is mostly inert and will withstand highly corrosive products and avoid contamination through breakdown. Abrasion and Ozone Resistant The cover protects the body from stiffening and cracking caused by ozone and UV exposure. It also adds abrasion resistance for extended hose life. Non-Kinking The internal helical wire structure helps prevent kinking. Multi -Ply Acid Discharge Hose Designed to handle most of the common acids and alkali solutions under pressure. Multi-Ply Acid Suction Hose This hose features a high-tensile textile cord with wire helix to prevent collapse under vacuum conditions. Recommended Cleaning of Chemical Hose 1. Drain the hose after each use. 2. Flush with water or other neutralizing cleaning solution. 3. Properly dispose of drained fluid and cleaning waste. 4. Between uses, store the hose in a clean, dry environment away from sunlight. 5. Avoid cross contamination. Dedicate a hose to handle a specific chemical.
Product name: Organic palm sugar Form: Arenga pinnata and cocos nucifera caramelized extract (pallet / granule). Aranga pinnata and cocos nucifera liquid extract. Production capacity: 60 tons / month Price FOB (Indonesia port): USD $ 3.00 – USD $ 8.00 / Kg Packing: 40kg pp gunne bags / cartoon or wood box / as buyer request Documents: as buyer request Shipping: as buyer request ( sea cargo / air cargo) or we could provide best option to proceed it using our local partner for logistic or forwarder company as long with buyer approval. Payment: 50% by TT / bank transfer in advance, and 50% by TT/bank transfer/LC while ready for shipping (all document submitted: B/L, COO, etc). Samples are available and free. We could send sample you need to any address you want worldwide, with postal cost paid by buyer. Cultivation and manufacturing inspection by buyer or buyer visiting are warmly welcome. Bulk
Plastic Cascade Mini Ring is made from heat resistant and chemical corrosion resistant plastics, including polyethylene (PE), polypropylene (PP), reinforced polypropylene (RPP), polyvinyl chloride (PVC), chloridized polyvinyl chloride (CPVC) and polyvinylidene fluoride (PVDF). It has features such as high free volume, low pressure drop, low mass-transfer unit height, high flooding point, uniform gas-liquid contact, small specific gravity, high mass transfer efficiency and so on .The application temperature in media ranges from 60¡ãCto 150¡ãC. For these reasons it is widely used in the packing towers in petroleum industry, chemical industry, alkali-Chloride industry, coal gas industry and environmental protection, etc. Applications: Absorption and stripping services Many environmental applications Place of Origin Jiangxi, China (Mainland) Brand Name Kelley Model Number K-PCMR Size 16.25.38.50.76mm Certificate ISO9001:2000 Materials PP PE PVC CPVC PVDF Shape tower shape. 1.)25kg woven bags+pallet,ton bags with wooden pallet. 2.)cartons +pallets. 3.)packed as per customer's request.
Solar keymark Solar collector Reliable, efficient, twin-glass solar tubes heat pipe Copper heat pipes for rapid heat transfer Corrosion resistant brazed copper header Fetures: 1) length: 1800mm; thickness: 0.8mm 2) the manifold: Made of red copper Conducted by heat transfer medium liquid 3) the out casing: Made of aluminum alloy mold material of high-strength with air flow design 4) water can't flow into vacuum tubes 5) resistant to high-pressure( 6bars) 6) resistant to extremely cold or hot environment 7) no harm or pollution, environment protective, clean, healthy Economic, invest once and benefit for ever 8) to assemble many collectors together for the solar central heating project of the hotel and factory are permitted. Modelabsorb a rea (m2)heat pipesupply hot water (l/)qty. Per 20/40 container (set) Diameter(mm) length (mm) no. (pcs) Free/j-1800/58-181.4458180018150/6084/175 Free/j-1800/58-201.6058180020175/6077/160 Free/j-1800/58-241.9258180024220/6064/133 Free/j-1800/58-302.4058180030260/6052/106 Whole packaging
CNC Lathe Machine The lathe features: 1. This vertical CNC lathe is a advanced equipment of high performance, widely technology range, high production efficiency. It lathe is apply to machining of all industries. Rough and finish machining of insideï¼?outside cylindrical surface, circular conical surface, end face, grooving, arc surface, sorts of curve face and thread 2. Worktable main spindle adopts high precision and adjustable radial clearance biserial short cylindrical roller bearing to centering to centering. Axial direction adopts CC hydrostatic guideway, worktable have the features of high running accuracy, big bearing capacity, small thermal deformation. 3. The lathe feed adopts AC servo motor, ball screw for drive. Rail head of cross beam equipped with close shield, increase the safety and the amenity 4. The lathe feed adopts AC motor drive, 16 steps main spindle speed change mechanism and realize the worktable range of speed 5. CNC system can select import or domestic according to user needs, CK51A series not have cover housing, CK51B series have cover housing, chip removal and cooling liquid recovery device 6. Vertical column, cross beam guideway all use high-frequnency, quenching, and the quenching hardness is HRC48-55 More information you can views here Technical specifications: Specification UNIT CK5108A/B*H/2 Max. turningDiameter Mm 800 Table diameter Mm 720 Max. height of workpiece Mm 800 Max. weight of workpiece T 2 Max. torqueOf table KN.m 20 Range of table speeds r/min 10-315 Max. cutting force of rail head KN 18 Swivel of rail head Range of feed rates Mm/min 0.1-500 Horizontal travel of railhead Mm 570 Ram travel of rail head Mm 650 Rapid traverse of tool head Mm/min 4000 Elevating speed of cross rail Mm/min 440 Height of tool bar section Mm 30*470 Power of main motor KW 22 Overall dimensions Mm 2080*1820*2730 3580*2300*2730 Weight of machine t 7.2/8.5
Electric Heating Conduction Oil Furnace Details Working Principle For Qilian electric heat conduction oil furnace (also known as heat conduction oil heater), the electric heater is directly inserted into the organic carrier (heat conduction oil) for direct heating. A circulating pump is used to create liquid-phase circulation of heat conduction oil, thus, to transfer the heat to one or several pieces of heat using equipment. After unloaded in the heat using equipment, the heat conduction oil will return to the heater via the circulating pump, again to absorb heat, and transfer the heat to the heat using equipment. This process is repeated again and again, realizing continuous transfer of heat. As a result, the temperature of objects being heated rises, and heating requirements are fulfilled. Composition Qilian electric heat conduction oil furnace system is composed of an explosion-proof electric heater, an organic heat carrier furnace, a heat exchanger (configurable), a control cabinet, a hot oil pump, and an expansion slot. The user only needs to connect the equipment to a power supply, and arrange medium inlet and outlet pipes and electrical interfaces before use. Application Scope Qilian electric heat conduction oil furnace adopts a digital display temperature controller, and has functions of over temperature alarm, low oil level alarm and over pressure alarm. This product is a type of high-efficiency energy-saving heating equipment for chemical, petroleum, machinery, printing and dyeing, foodstuff, marine, textile, and film industry, etc. Characteristics 1. Low Operating Pressure Liquid phase heat transfer can reach a higher operating temperature under lower operating pressure; saturated vapor pressure of heat carrier is 70 to 80 times lower than that of water; and its general operating pressure is 0.3mp 2. High Heating Temperature Heating temperature of the electric heat conduction oil furnace may reach 280heating-up temperature is automatically controlled, realizing high sensitivity and stable heat supply. 3. Safe and Reliable Our electric heat conduction oil furnace is equipped with a perfect operating control and safety monitoring device, so it is easy to operate, safe, and reliable. 4. Environmental Friendly Design The electric heat conduction oil furnace is a new type of electric heating system. Electricity is used instead of coal, which reduces investment outlay and is free from contamination; meanwhile, heat conduction oil furnace, with short heating time and high thermal efficiency, is more efficient and economical.
Product Description IES Ideal End Suction Pump IES Series is single stage, single suction back pull out type Dimensions are according to EN733 (DIN24255) standard Flange can be drilled according to ISO, DIN, BS or ANSI standard Shaft with mechanical seal as standard and gland packing optional Materials available (Cast iron, Ductile iron and SS316 etc.) Performance Range Flow Rate (Q) Up to 1100 m3/h Head (H) Up to 152m Speed (RPM) 1450~2900 rpm (50HZ), 1750~3500 rpm (60HZ) Temperature -10 Celsius to 105 Celsius, (Optional 130 Celsius) Applications HVAC & Cooling Tower Fire Fighting Chemical Liquid Transfer Irrigation & Agriculture Booster & Pressurization Set Definition of Model IES 65/20 IES - Single Stage, End Suction Pump 65 - Discharge Diameter (mm) 20 - Impeller Nominal Diameter (mm)
Launder is a channel, normally internally lined, used for the transfer of molten aluminum. Launder is a good insulator, non-wetted by the molten aluminum, exhibit excellent mechanical strength including resistance to metal wear and physical damage. The launder is made of high strength heat insulation castable with good strength due to high temperature drying. Characteristics: 1, high mechanical strength; 4, high temperature resistance and small deformation; 2, anti-corrosion of aluminum liquid; 5, common refractoriness and easy to clean; 3, good heat insulation; 6, longer service life; Launder is used as a lining, excellent in high temperature resistance when transmits aluminum and aluminum alloy. The prefabricated launder and technical service can be specially designed of function and structure according to actual requirements to successful guarantee the qualified plate products casting. Ordinary material is the common materials fl for customers.
Chef Boiling Pan: Model No.: F - 801G Capacity: 68 L Weight: 105 Kgs Heating: Style / Voltage Size: 770 ( W ) × 960 ( D ) × 1140 / 1800 ( H ) mm Features : 1. Contact surface for food is made of made of stainless steel, in compliance with food sanitation standards. 2. Design of discharge outlet allows convenient transfer of cooked food to container. 3. Discharge outlet can be easily attached for convenience when cleaning. 4. Two - layered pan enables heating without charring the food. Mixer may be installed for cooking concentrated liquid. 5. Connector may be used to connect cold or hot water source to the faucet for convenience. 6. Triple protection with electronic pressure safty switch, mechanical exhaust valve and temperature control switch to meet the safety rules in many countries. 7. Electronic control panel for automatic ignition and temperature setting.
Applications: designed for handling liquefied hydrocarbon gases, volatile flammable and inflammable liquids as well as solutions of inorganic alkalis (sodium hydroxide) at the process plants in the oil-refining industry. May be also used to transfer water and condensate in the steam and water circuit systems. Design: ndms series motor pump units consist of a centrifugal pump and an induction motor in the explosion-proof version, which are mounted on a common fabricated base plate. The pump and motor shafts are connected by means of a flexible coupling. The pump units shall be rigidly anchored to the foundation, and piping shall be also rigidly connected to the pumps. The pumps as components of the pump units are electrically driven horizontal, centreline-supported, multistage ring section centrifugal pumps with rotor axial thrust balancing by a balance drum.
Full output fog 1200w smoke machine 1.Its atomization parts can adopt the compound aluminum of the fastest coefficient of heat transfer, which can reach to the best atomization temperature in a short time. 2.Produce thin transparent , dry and white smoke. 3.Suitable for opera theater, film, tv station and bars etc. Full output fog 1200w smoke machine Stage effect equipment:x-1200 fog machine Item no: x-1200 Power: 1000w Voltage: ac100v, 220v-250v Frequency: 50/60hz Control: regular quantity lines, or dmx512 Warm-up:12mins Tank capacity: 2.5l Liquid consumption (100% output):45min/liter Output: 3500cu.Ft/min Weight: 20kg Size: 630*290*290mm Catalogue will be send if needs. Please contact us or email us at anytime, if you have any question. Parper carton
Pad Printing Silicone Rubber Usages: Pad printing silicone rubber is mainly use for printing irregular patterns of plastic toys, electroplating toys and trade makers . Pad printing silicone rubber as a carrier which transfer patterns on the steel plate to the toys products surface. Pad Printing Silicone Rubber Features: Pad printing silicone rubber with high print times and abrasion resistance. Pad printing silicone rubber has good printing effects, permanent and durable. We can provide all kinds of color and our catalyst is free. Pad Printing Silicone Rubber Operation Instructions: Pad printing silicone rubber is two-component silicone, part A is liquid silicon rubber, part B is catalyst. 25kg/drum
N-methyl-pyrrolidone N-methyl-pyrrolidone that is also called n-methyl-2-pyrrolidone is written f¬nmpf¬ for short. The molecular formula is c5h9no. N-methyl-pyrrolidone, which is a liquid with little ammonia odor, can mix with almost all solvents such as ethyl alcohol, acetaldehyde, ketone, aromatic hydrocarbons and chlorohydro carbons etc. Its boiling point 204fp and flash point 95fp. Nmp which is a polar non proton transfer solvent possesses little toxicity, high boiling point, powerful solvency, good selectivity and stability properties. The product is widely applied to aromatic hydrocarbons extracting, acetylene, and diolefine purification. It can be also used as polymer solvents and polymerization process medium, such as polyamides, polyimides and polyphenyl thioether(pps) , etc. Which are called engineering plastics. Besides these, it can be used as aromatic fibre, insulate pesticide, pigment and detergent, etc. 200kg/drum
Products characteristics Large amount of load and requiring small area for equipment Difficult to clean when mixing glutinous or cohesive materials Working principle This mixer consists of a container, helix mixing blades and transmission parts. The helix blades are in two or three tiers. The outer helix will move the material from its two sides to the central part, while the inner helix will transfer the material to the two sides, performing a kind of convection mixing. Application scope The ribbon mixer is generally used in mixing adhesive or cohesive powder granules and mixing processes in which liquid and pasty materials are added. It is especially suitable for mixing materials with a large quantity and whose types are not frequently changed because of the cleaning difficulties.
Jacketed Hose assembly consists of a hose within a hose. An inner (Core Hose) or primary media conveying hose is enclosed or jacketed by a larger diameter hose. The hoses are joined at each end by specially designed fittings so that there is no media pathway between the two hoses. Jacketed Hose assemblies are often specified when the primary media must be kept at either an elevated or cryogenic temperature. Steam is often circulated through the jacket hose to keep a viscous material in the inner hose hot and easily conveyed. A vacuum can also be pulled on the jacket hose to insulate cryogenic liquids being conveyed in the inner hose. The media typically is steam, hot oil or hot water to raise the temperature of the fluid moved in the internal hose. Also cold products such as liquid helium or nitrogen can be used to lower the temperature of the fluid with-in the internal hose. Jacketed hose assembly with inlet and outlet swivel flanges fitted with both side swivel flange) and sometime threaded also use, inlet and out let of jacket hose's fitting can be threaded type also, and length of hose assembly depends upon the how much heat area require to maintain. For more Detail of fitting see the following table These hoses are used to transfer high density fluid, like bitumen, pre polymers, hot melts etc
Perkin Elmer Automated Workstation Tips 900 ul Filter Tip, Clear We offer sterile and non-sterile tips for a variety of dispenser channel sizes and volume requirements. Tips to support liquid transfers from multiple laboratory containers including test tubes, vials, troughs, deep-well plates, and microplates (up to 384-well) are available as well. Our portfolio of consumables includes both cell-based and biochemical assay platforms, reagents, and kits, as well as a complete range of high quality and application-focused microplates for your assay applications, detection technologies, or plate reader requirements. Our Clear MBP Tips for the Varispan Arm provide liquid level sensing and are available in ten 96-tip racks/case. Specifications Automation Compatible Yes Color - Clear Disposable Tip Types - clear, non-sterile Pipetting Arms - Varispan Product Brand Name - JANUS Quantity in a Package Amount - 10.0 Units Unit Size - 900 ul Volume Capacity - 900 L
Shandong Zeko Machinery Co., Ltd. is located in Zhucheng, Shandong Province. It is near the "Kite Capital" Weifang in the north, Rizhao, a coastal city in the south, and Qingdao, an international coastal city in the east. The glass bottle washing machine / canned bottle washing machine is composed of washing liquid washing zone, water purification washing zone and drying zone. The stainless steel chain is used to drive the bottle to the washing liquid washing area, then pass through the water washing area, and finally dry it to transfer the washed bottle. Each washing area of the glass bottle washing machine / canned bottle washing machine is equipped with a stainless steel water pump circulating spray cleaning, and the bottles are sprayed and rinsed simultaneously from the four directions of up, down, left, and right, and the washing rate is high. Low pressure pump is used to circulate and boost the bottle, and the water consumption is low. Glass bottle washing machine / canned bottle washing machine are widely used for glass bottle cleaning after food filling, and for cleaning and disinfecting empty cans before filling canned food. Shandong Zeko Machinery Co., Ltd. is a modern enterprise integrating R & D, production, sales and service. It has all kinds of technical talents and many years of manufacturing experience, and its products are durable and well received by customers.