Application areas: Measuring-level current transformer used in power system, transformer used on precision measuring instruments (such as watt-hour meter). According to the requirements of different measurement accuracy of the transformer, different soft magnetic materials can be chosen as iron core materials. The higher the permeability of the iron core is, the smaller the measurement error of the transformer is, hence the accuracy is higher. At present, the most common iron core material is cold-rolled silicon steel sheet, followed by Permalloy and nano-crystalline glass alloy. In recent years, demands for transformers with high-precision level (such as class 0.2, class 0.2Sand class0.5S) increased rapidly. When small ratio, low ampere turns are required or the iron core is restricted because of the small volume, the cold-rolled silicon steel often fails to meet the accuracy requirements. Although the Permalloy iron cores with high permeability can meet the required precision, its price is very high. However use of nano-crystalline alloy iron cores can both meet the accuracy requirements and be produced at lower cost than the Permalloy. Therefore, the demand of measuring level current transformer iron core made of nano-crystalline alloy rapidly increased domestically. The typical parameters comparison of the common soft magnetic materials used for current transformer iron cores: Basic parameters Nano-crystalline iron core Permalloy (1J85) iron core Silicon steel iron core Saturation magnetic flux density (Bs) 1.25T 0.75T 2.03T Initial permeability (¦Ì0) 8¡«12, 104 5¡«8, 104 103 Maximum permeability (¦Ìm) 60, 104 60, 104 4, 104 Curie Temperature (¡æ) 570 400 740 Density (g/cm3) 7.25 8.75 7.65 Lamination factor 0.7 0.9 0.95 Thickness (mm) 0.03 0.15 0.3 Features: It is made of the iron-based nano-crystalline strips with a moderate saturation magnetic induction, high permeability and low loss, which can effectively reduce ratio difference angle difference of the transformer. The saturation magnetic induction Bs of nano-crystalline alloy is between the silicon steel and Permalloy. The lower the Bs value is, the lower the security coefficient of the instrument is. When the system failure occurs and large current through the current transformer results therefore, the iron core is more easily filled, and the secondary current no longer increases in proportion, as can assure that the secondary instruments are well protected and not to be damaged. Permeability of nano-crystalline alloy is close to Permalloy and a magnitude higher than silicon steel, so it is suitable to be made as high-precision transformer iron core. The density and lamination coefficient of nano-crystalline is lower than that of Permalloy, under the condition of the same size and similar performance of the two. In this case the nano-crystalline iron core is 1/4 lighter in weight, and 1/3 lower in the manufacturing cost. In addition, the linear range of nano-crystalline alloy is wider than that of Permalloy .It can work for a long time at temperature of -55 ~ 130 ¡æ ,with a good temperature stability. Specifications a. Rectangular core: (mm) Iron Core Size(mm) (mm) The case size(mm) Weight of the iron Core (kg per piece) Turns Ratio N1: N2 Excitation current(mA) Excitation voltage(mV) 55*97/77*119, 25 50*92/82*114, 30 0.53 1:1 25 0.45 95 2.2 1500 53 70*90/100*120, 30 65*85/105*125, 36 0.81 1:1 200 15 1:1 500 50 75*95/105*125, 25 70*90/110*130, 30 0.7 1:1 70 2 1:1 175 8 80*95/120*135, 25 75*90/125*140, 30 1.09 1:1 80 1.7 1:1 600 41 90*90/160*160, 30 85*85/165*165, 36 2.4 1:1 100 6 1:1 500 100 1:1 1000 140 135*135/260*260, 10 130*130/265*265, 16 2.3 1:1 100 1.5 1:1 500 32 82*602/138*658, 45 75*595/145*665, 55 8.8 1:1 100 1.2 1:1 1000 45 1:1 2000 120 b. Ring core: No. The iron Core Size Case size(mm) The weight of the iron core (kg per piece) Turns ratio N1: N2 is 1:1; Input current (mA), 50Hz; Output voltage (mV) 1 1105/1165, 15 1095/1175, 25 8.35 Excitation current 450 1200 2000 Excitation voltage 0.59 2.36 5.28 2 415/520, 15 409/526, 23 6.08 Excitation current 50 250 700 Excitation voltage 0.4 3 11 3 305/490, 15 299/496, 23 9.1 Excitation current 350 900 ¡¡ Excitation voltage 5 20 ¡¡ 4 315/395, 35 309/401, 43 8.2 Excitation current 120 400 ¡¡ Excitation voltage 3 11 ¡¡ 5 198/248, 30 192/254, 37 2.76 Excitation current 100 200 500 1000 Excitation voltage 2 6 35 90 6 198/248, 20 192/254, 27 1.84 Excitation current 100 200 500 1000 Excitation voltage 1.5 3.5 25 60 7 155/200, 30 150/205, 36 2 Excitation current 100 190 1000 Excitation voltage 2.5 9.5 80 8 140/180, 30 135/185, 36 1.58 Excitation current 40 80 240 Excitation voltage 1 2.9 15 9 130/190, 30 125/195, 36 2.38 Excitation current 40 80 240 Excitation voltage 1.2 3.8 17 10 100/140, 30 95/145, 36 1.19 Excitation current 30 120 500 Excitation voltage 0.85 6.8 68 11 90/130, 30 85/135, 36 1.09 Excitation current 30 120 500 Excitation voltage 0.7 6 55 12 90/125, 25 85/130, 31 0.78 Excitation current 30 120 500 Excitation voltage 0.9 7 70 13 80/120, 30 75/125, 36 0.99 Excitation current 200 500 ¡¡ Excitation voltage 20 65 ¡¡ 14 85/115, 30 80/120, 36 0.74 Excitation current 30 120 500 Excitation voltage 0.7 6.5 55 15 85/125, 20 80/130, 26 0.7 Excitation current 30 120 500 Excitation voltage 0.62 5.5 50. wooden case+carton box.
Application areas: Measuring-level current transformer used in power system, transformer used on precision measuring instruments (such as watt-hour meter). According to the requirements of different measurement accuracy of the transformer, different soft magnetic materials can be chosen as iron core materials. The higher the permeability of the iron core is, the smaller the measurement error of the transformer is, hence the accuracy is higher. At present, the most common iron core material is cold-rolled silicon steel sheet, followed by Permalloy and nano-crystalline glass alloy. In recent years, demands for transformers with high-precision level (such as class 0.2, class 0.2Sand class0.5S) increased rapidly. When small ratio, low ampere turns are required or the iron core is restricted because of the small volume, the cold-rolled silicon steel often fails to meet the accuracy requirements. Although the Permalloy iron cores with high permeability can meet the required precision, its price is very high. However use of nano-crystalline alloy iron cores can both meet the accuracy requirements and be produced at lower cost than the Permalloy. Therefore, the demand of measuring level current transformer iron core made of nano-crystalline alloy rapidly increased domestically. The typical parameters comparison of the common soft magnetic materials used for current transformer iron cores: Basic parameters Nano-crystalline iron core Permalloy (1J85) iron core Silicon steel iron core Saturation magnetic flux density (Bs) 1.25T 0.75T 2.03T Initial permeability (¦Ì0) 8¡«12, 104 5¡«8, 104 103 Maximum permeability (¦Ìm) 60, 104 60, 104 4, 104 Curie Temperature (¡æ) 570 400 740 Density (g/cm3) 7.25 8.75 7.65 Lamination factor 0.7 0.9 0.95 Thickness (mm) 0.03 0.15 0.3 Features: It is made of the iron-based nano-crystalline strips with a moderate saturation magnetic induction, high permeability and low loss, which can effectively reduce ratio difference angle difference of the transformer. The saturation magnetic induction Bs of nano-crystalline alloy is between the silicon steel and Permalloy. The lower the Bs value is, the lower the security coefficient of the instrument is. When the system failure occurs and large current through the current transformer results therefore, the iron core is more easily filled, and the secondary current no longer increases in proportion, as can assure that the secondary instruments are well protected and not to be damaged. Permeability of nano-crystalline alloy is close to Permalloy and a magnitude higher than silicon steel, so it is suitable to be made as high-precision transformer iron core. The density and lamination coefficient of nano-crystalline is lower than that of Permalloy, under the condition of the same size and similar performance of the two. In this case the nano-crystalline iron core is 1/4 lighter in weight, and 1/3 lower in the manufacturing cost. In addition, the linear range of nano-crystalline alloy is wider than that of Permalloy .It can work for a long time at temperature of -55 ~ 130 ¡æ ,with a good temperature stability. Specifications a. Rectangular core: (mm) Iron Core Size(mm) (mm) The case size(mm) Weight of the iron Core (kg per piece) Turns Ratio N1: N2 Excitation current(mA) Excitation voltage(mV) 55*97/77*119, 25 50*92/82*114, 30 0.53 1:1 25 0.45 95 2.2 1500 53 70*90/100*120, 30 65*85/105*125, 36 0.81 1:1 200 15 1:1 500 50 75*95/105*125, 25 70*90/110*130, 30 0.7 1:1 70 2 1:1 175 8 80*95/120*135, 25 75*90/125*140, 30 1.09 1:1 80 1.7 1:1 600 41 90*90/160*160, 30 85*85/165*165, 36 2.4 1:1 100 6 1:1 500 100 1:1 1000 140 135*135/260*260, 10 130*130/265*265, 16 2.3 1:1 100 1.5 1:1 500 32 82*602/138*658, 45 75*595/145*665, 55 8.8 1:1 100 1.2 1:1 1000 45 1:1 2000 120 Note: Iron cores of other specifications can be provided upon request of users b. Ring core: No. The iron Core Size Case size(mm) The weight of the iron core (kg per piece) Turns ratio N1: N2 is 1:1; Input current (mA), 50Hz; Output voltage (mV) 1 1105/1165, 15 1095/1175, 25 8.35 Excitation current 450 1200 2000 Excitation voltage 0.59 2.36 5.28 2 415/520, 15 409/526, 23 6.08 Excitation current 50 250 700 Excitation voltage 0.4 3 11 3 305/490, 15 299/496, 23 9.1 Excitation current 350 900 ¡¡ Excitation voltage 5 20 ¡¡ 4 315/395, 35 309/401, 43 8.2 Excitation current 120 400 ¡¡ Excitation voltage 3 11 ¡¡ 5 198/248, 30 192/254, 37 2.76 Excitation current 100 200 500 1000 Excitation voltage 2 6 35 90 6 198/248, 20 192/254, 27 1.84 Excitation current 100 200 500 1000 Excitation voltage 1.5 3.5 25 60 7 155/200, 30 150/205, 36 2 Excitation current 100 190 1000 Excitation voltage 2.5 9.5 80 8 140/180, 30 135/185, 36 1.58 Excitation current 40 80 240 Excitation voltage 1 2.9 15 9 130/190, 30 125/195, 36 2.38 Excitation current 40 80 240 Excitation voltage 1.2 3.8 17 10 100/140, 30 95/145, 36 1.19 Excitation current 30 120 500 Excitation voltage 0.85 6.8 68 11 90/130, 30 85/135, 36 1.09 Excitation current 30 120 500 Excitation voltage 0.7 6 55 12 90/125, 25 85/130, 31 0.78 Excitation current 30 120 500 Excitation voltage 0.9 7 70 13 80/120, 30 75/125, 36 0.99 Excitation current 200 500 ¡¡ Excitation voltage 20 65 ¡¡ 14 85/115, 30 80/120, 36 0.74 Excitation current 30 120 500 Excitation voltage 0.7 6.5 55 15 85/125, 20 80/130, 26 0.7 Excitation current 30 120 500 Excitation voltage 0.62 5.5 50. wooden case+carton box.
Varnished Wooden Brooms Handles , Size D.22/23 Mm X L.120 Cm Varnished Wooden Brushes Handles, Size D. 22/23 Mm X L.150 Cm Varnished Wooden Mop Handles, Size D.28/30 Mm X L.150 Cm , Varnished Wooden Shovel Handles, Size: D.40 Mm X L. 145 Cm Product Item : Top Dome , End Of Tapper / Flat Cut / Thread Wood Item ; Tropical Hard Wood -
1. Material: Stainless Steel, copper, Al, etc 2. Thickness: 0.02mm~1.5mm 3. Technique: chemical etching, high precision etching 4. Environmental and economical 5. Low tooling cost 6. Surface treatment: good flatness, no scratches, no burr, no broken point, no plugging holes, etc
Grade : Titanium Bar/Rod Diameter : Dia6.0--400mm Length 4000mm Grade Gr 1, Gr 2, Gr 3, Gr 4, Gr 5, Gr 7, Gr 9, Gr 12, Gr 23 etc. Standard: ASTM B348, ASTM F136, ASTM F67 etc. Type : Ti round bar, Ti square bar, Ti flat bar, Ti hexagonal bar Application : Industrial, chemical industry, military industry, medical industry etc.
0.6MPA FRP TANKS (30 to 63 INCH) FOR INDUSTRIAL USE FRP Water Softening, Filter Tanks-Economy 100PSI-Rohone&Aowy Series FOR INDUSTRIAL: 30" to 63" FRP Water Softening, Filter Tanks-Economy 100PSI-Rohone&Aowy Series FOR INDUSTRIAL: 30" to 63" HEBEI CHENGDA HUAMO(HBCDHM in short) manufactures FRP tanks with design pressure 1.0Mpa(150Psi), 0.6Mpa(approx 100Psi) to meet various needs of the users. Structure and Materials of FRP Tanks Liner material: Rotation molding or Blowing One-piece seamless PE liner Outer Winding: High performance Epoxy resin + Fiberglass three-dimensional winding reinforcement. Opening: 2.5" and 4" reinforced plastic thread; 6" alloy flange. Base Materials: FRP or reinforced PP ASME Certification frp tanks Application Conditions Working Pressure: 150 psi(10.5 bar) for Winder series 0.6Mpa for Rohone and Aowy economy series. Working Temperature: 1 C - 49 C (34F - 120F) Max. Vacuum: 127mmHg Lowest Environment Temperature:-27 C (-17F) Strict Quality Control(Q/A) Fatigue test: 250, 000 times. (standard 100, 000 times) Burst test: 4 times of its design pressure. Certification: NSF & ACS, ASME Model: 0517-8079. Rohone and Aowy FRP tank also is Chengda brand: 100 Psi. (Chengda is the FRP RO membrane housing and FRP tanks production base for Frotec - the largest water treatment trading company in China. AOWY brand only for Frotec.) Specification of frp tanks No. Model Nominal dimension Opening Volume Base Dimension Top Bottom litre Gallon A (mm) B (mm) C (mm) D (mm) 1 06�?17 150*450 2.5"-8NPSM / 6.7 1.8 Standard 437 161 / 55 2 0635 150*890 2.5"-8NPSM / 15 4.0 Standard 896 61 / 155 3 0713 180*330 2.5"-8NPSM / 6.3 1.7 Standard 335 188 / 180 4 0717 180*432 2.5"-8NPSM / 8.6 2.3 Standard 437 188 / 180 8 0735 180*890 2.5"-8NPSM / 20.1 5.3 Standard 895 �¦188 / 180 9 07�?44 180*1110 2.5"-8NPSM / 24.5 6.5 Standard 1125 188 / 180 10 0813 200*330 2.5"-8NPSM / 8.5 2.2 Standard 335 216 / 207 FEATURE Chengda Winder, Rohone, and Aowy FRP softner tanks quality assurance: burst test with 4 times of its design pressure, and 250000 times cycle test. 1.HBCDHM FRP tanks (844-1665) use 600 TEX fiberglass, not 1200TEX fiberglass, with higher safety factor. 2.The base of HBCDHM FRP tank is made from pure raw material not recycled material, With better appearance, stronger toughness, and more environmentally friendly. 3.Key additives are imported from the US. APPLICATION HBCDHM FRP tanks are widely l used for water softening equipment in food processing plants, hospitals, laundries, manufacturing plants, office campuses and restaurants, condominiums, boiler feedwater, car washes, institutions, municipal, multimedia filters, carbon filters, iron filters, calcite filters and specialty media filters
300x600 mm ceramic wall tiles 10 mm thickness 0.9 sq. MTR in box Wt. Of box= above 14400 as requirement Other specifications:- 1)Thermal shock= resistant to 10 cycle 2) Watermark 3) Water absorption (euro standard)=>10% 4) Surface flatness(euro standard=+_ 0.5% 5) Dimension (euro standard=+_0.5% 6) Bending strength (euro standard) => 150 kg/cm2 7) crazing (euro standard)= 1 cycle
300x600 mm ceramic wall tiles 10 mm thickness 0.9 sq. MTR in box Wt. Of box= above 14400 as requirement Other specifications:- 1)Thermal shock= resistant to 10 cycle 2) Watermark 3) Water absorption (euro standard)=>10% 4) Surface flatness(euro standard=+_ 0.5% 5) Dimension (euro standard=+_0.5% 6) Bending strength (euro standard) => 150 kg/cm2 7) crazing (euro standard)= 1 cycle
Application and Specification 1 Design: JIS B2071/ASME B16.34 2 Face to Face: JIS B2002 3 Flange ends: JISB2220 4 Inspection & Test: JIS B2003 Main Parts and Materials Part Name: Material Mesh: 304/304/316 Body: SCPH2/SCS13/SCS14 Drain plug: SM25C/SCS13 Gasket: PTFE/304+Graphite(20K) Stud: SM45C/304 Bonnet: SCPH2/SCS13/SCS14 Nut: SM35C/304 Main External and Connecting Dimensions JIS-10K Y Strainer NPS D1 d K D f C N-â?®Z L H 50A 50 96 120 155 2 16 4-19 232 115 65A 65 116 140 175 2 18 4-19 285(268) 145 80A 80 126 150 185 2 18 8-19 302(287) 164 100A 100 151 175 210 2 18 8-19 377(340) 212 125A 125 182 210 250 2 20 8-23 392 263 150A 150 212 240 280 2 22 8-23 442 295 200A 200 262 290 330 2 22 12-23 540 380 250A 250 324 355 400 2 24 12-25 665 505 300A 300 368 400 445 3 24 16-25 765 550
Hexagonal Wire Nettings Produced With Superior Quality Low-Carbon Iron Wire,Normally Galvanized Plastic Coated For Long Life,The Mesh Is Firm In Structure And Has Flat Surface.Hexagonal Wire Netting Is Exensively Used In Industrial And Agricultural Constructions.Also It Can Be Used As Fence For Poultry Cage. Fishing, Garden, Children Playground And Christmas Decorations. HEX.Wire Netting In Normal Twist (IN 5m,10m,25m,30m,100m,TO 3000m ROLL,WIDTH OF 0.5m-2.0m) MESH WIRE GAUGE INCH MM BWG 3/8 10MM 27, 26, 25, 24, 23, 22, 21 1/2 13MM 27, 26, 25, 24, 23, 22, 21, 20 5/8 16MM 27, 26, 25, 24, 23, 22 3/4 20MM 25, 24, 23, 22, 21, 20, 19 1 25MM 25, 24, 23, 22, 21, 20, 19, 18 1-1/4 30MM 22, 21, 20, 19, 18 1-1/2 40MM 22, 21, 20, 19, 18, 17 2 50MM 22, 21, 20, 19, 18, 17, 16, 15, 14 3 75MM 21, 20, 19, 18, 17, 16, 15, 14 4 100MM 17, 16, 15, 14 HEX.WIRE NETTING IN NORMAL TWIST (IN 5m,10m,25m,30m,100m,TO 3000m ROLL,WIDTH OF 0.5m-2.0m) MESH WIRE GAUGE INCH MM (BWG) 1 25MM 22, 21, 20, 19, 18 1-1/4 30MM 22, 21, 20, 19, 18 1-1/2 40MM 20, 19, 18,17 2 50MM 20, 19, 18,17,16 3 75MM 20, 19, 18,17,16 HEX.WIRE NETTING IN PVC-COATED (IN LENGTH OF 5M,10M,25M,30M,WIDTH OF 0.5M,1.0M,1.2M,1.5M) MESH WIRE GUAGE 1/2 13MM 0.9MM,1.0MM 5/8 16MM 0.9MM,1.0MM 3/4 19MM 0.9MM,1.0MM 1 25MM 1.0MM,1.2MM,1.4MM 1-1/2 40MM 1.0MM,1.2MM,1.4MM,1.6MM 2 50MM 1.0MM,1.2MM,1.4MM,1.6MM,2.0MM Packing: In Roll Wrapped By Water-Proof, Or Shrink Wrapped. Remark: Sizes Other Than Those Above-Mentioned May Be Made To Order After Consideration. Common Carton: It Can Protect The Inner Goods And Easy To Handle, Transport And Stock. Mini Roll Normally In The Length Of 3m,5m And 10m,Shrink Wrapped With Color Label And Barcode,Then Into Cartons,They Are Ideal For Pet Cage,Window Prodection,Tree Guard,Other Home And Garden Usage
K500 (Same with SB45) Operating Weight(Including Tool) Top Type - 577 kg, 1269 lbs Side Type - 510 kg, 1122 lbs Box Type - 571 kg, 1256 lbs Operating Height(Including Tool) Top Type - 1946 mm, 76.6 inch Side Type - 1767 mm, 69.5 inch Box Type - 2101 mm, 82.7 inch Operating Pressure - 130 ~ 160 bar Required Oil Flow - 60 ~ 100 l/min Hose Diameter - PF 3/4 inch Tool Diameter - 85 mm, 3.34 inch Applicable Excavator - 7.0 ~ 14 ton, 15428 ~ 30856 lbs K600 (Same with SB50) Operating Weight(Including Tool) Top Type - 890 kg, 1958 lbs Side Type - 765 kg, 1683 lbs Box Type - 861 kg, 1894 lbs Operating Height(Including Tool) Top Type - 2338 mm, 92.0 inch Side Type - 1939 mm, 76.3 inch Box Type - 2326 mm, 91.5 inch Operating Pressure - 150 ~ 170 bar Required Oil Flow - 80 ~ 110 l/min Hose Diameter - PF 3/4 inch Tool Diameter - 100 mm, 3.93 inch Applicable Excavator - 11 ~ 16 ton, 24244 ~ 35264 lbs HB15G Operating Weight(Including Tool) Top Type - 1100 kg, 2420 lbs Side Type - 1030 kg, 2266 lbs Box Type - 1234 kg, 2715 lbs Operating Height(Including Tool) Top Type - 2470 mm, 97.2 inch Side Type - 2035 mm, 80.1 inch Box Type - 2550 mm, 100.3 inch Operating Pressure - 150 ~ 170 bar Required Oil Flow - 90 ~ 120 l/min Hose Diameter - PF 1 inch Tool Diameter - 120 mm, 4.72 inch Applicable Excavator - 12~ 18 ton, 26448 ~ 39672 lbs K700 (Same with SB60) Operating Weight(Including Tool) Top Type - 1431 kg, 3148 lbs Side Type - 1255 kg, 2761 lbs Box Type - 1297 kg, 2853 lbs Operating Height(Including Tool) Top Type - 2510 mm, 98.8 inch Side Type - 2089 mm, 82.2 inch Box Type - 2604 mm, 102.5 inch Operating Pressure - 150 ~ 170 bar Required Oil Flow - 90 ~ 120 l/min Hose Diameter - PF 1 inch Tool Diameter - 125 mm, 4.92 inch Applicable Excavator - 15 ~ 18 ton, 33060 ~ 39672 lbs K800 (Same with SB70) Operating Weight(Including Tool) Top Type - 1675 kg, 3685 lbs Side Type - 1452 kg, 3194 lbs Box Type - 1500 kg, 3300 lbs Operating Height(Including Tool) Top Type - 2620 mm, 103.1 inch Side Type - 2289 mm, 90.1 inch Box Type - 2691 mm, 105.9 inch Operating Pressure - 160 ~ 180 bar Required Oil Flow - 100 ~ 150 l/min Hose Diameter - PF 1 inch Tool Diameter - 135 mm, 5.31 inch Applicable Excavator - 16 ~ 21 ton, 35264 ~ 46284 lbs
Model: IRA-HP58/1.8-OEM12 Color: Custom made Material of out tank: 0.31mm thickness color steel/ fluorine carbon steel Material of inner tank: Food grade 1.0 mm thickness SUS304 stainless steel Tank insulating layer: 50mm thickness, 45kg/m3 high-density polyurethane foamed Inlet and outlet hole: Female G 3/4 Max pressure: 0.9Mpa Solar collector tube: 3.3 Borosilicate glass with Al-SS/Cu coating 58x1,800mm with heat pipe Thickness of glass tube: 1.6mm Vacuum tube tightness: P0.005 Pa Absorption: as=0.93-0.96(AM1.5) Emission ratio: µh=0.04-0.06(80C±5C) Idle sunning property parameters: Y=220~260m2.C/KW Average heat loss coefficient: ULT=0.6~0.7W/(m2.C) Bracket: 1.0mm thickness of galvanized steel material Structure of tank: 4 holes for PT valve,water inlet and outlet,Mag Rod Welding: Argon arc welding Fastening pieces: Made of stainless steel screw Absorber area: 1.124m2 Heat pipe size: Dia14mm x 70mm length condenser,170cm length in total Heat pipe material: TU1 copper Heat pipe power: >120W/pcs Temperature tolerance: from -35C to 250C Tube quantity: 12 tubes Other Tube quantity: 8/10/12/15/18/20/24/30/36 tubes Tank capacity: 150L Other Tank capacity: 80/100/120/150/180/200/240/300/360L Heat pipe pressurized solar water heater features: 1.Adopts the best conduction performance metal- heat pipe (copper). 2.Can be used all year round in the cold climate. 3.High efficiency, rapid warming. Heat pipe in vacuum tube could transfer hot energy to cold water in pressurized solar water heater tank rapidly. 4.The whole pressure of the system is up to 1.5kg/M2, the inlet could connect the tap water directly, the max pressure can be 0.6Mpa. 5.No water in the tube, one tube broken don't influence the system working. 6.The design for inner tank is reasonable and scientific, which could hold 100, 000 times fatigue test without any damage. 7.Dual-purpose brackets for both flat and inclined roof. 8.The system is pressurized, it keep a constant temperature of water in the tank, avoid the problem came from water level controller malfunction which could cause water flow out. Pressurized solar water heater working principle: 1.The pressurized solar water heater tank has no exhaust hole, therefore, it must bear the pressure came from tap water. The hot water comes out because of water pressure. 2.Vacuum tube absorbs solar energy, and conductive copper pipe transfers the heat into the pressurized solar water heater tank. In this case, the water inside the tank becomes hot. 3.No water in the heat pipe makes the whole system could bear pressure.
FACE MASK ANTI POLLUTION , ANTO DUST , ANTI BACTERIAL 1.Comfortable breathing 2. Wider face coverage for maximum protection 3. Innovative 2-panel design for universal fit 4. Adjustable nose clip for enhanced protection 5. Soft, elastic ear loops for extra comfort 6. Minimal eyewear fogging 7. Low heat build-up 8. Convenient flat-fold design for easy storage 9. Washable and reusable 10. 3 Layer protection mask 11. 1st Layer airmesh 145-150 gsm 12.3nd layer hosiery lining 140-150 GSM 13.2nd Non woven filter cloth 25-30- GSM 14.Single plastic packing with literature printing 15. Non woven label branding as TR++ 3 color woven label 16. Colors available navy blue , white , red , black , grey , royal blue , mehandi .
FACE MASK ANTI POLLUTION , ANTO DUST , ANTI BACTERIAL 1.Comfortable breathing 2. Wider face coverage for maximum protection 3. Innovative 2-panel design for universal fit 4. Adjustable nose clip for enhanced protection 5. Soft, elastic ear loops for extra comfort 6. Minimal eyewear fogging 7. Low heat build-up 8. Convenient flat-fold design for easy storage 9. Washable and reusable 10. 3 Layer protection mask 11. 1st Layer airmesh 145-150 gsm 12.3nd layer hosiery lining 140-150 GSM 13.2nd Non woven filter cloth 25-30- GSM 14.Single plastic packing with literature printing 15. Non woven label branding as TR++ 3 color woven label 16. Colors available navy blue , white , red , black , grey , royal blue , mehandi .
Frozen Beef Brisket We Offer Premium Quality approved meat. Shipping to over 150 countries, where our factories are approved. Contact us for the best competitive bulk prices. Items Contents Primal beef brisket is one of the eight primal cuts Weight Ranges 4 lb -12 up Best Cooking Methods braising, slow cooking, smoking, stewing, pot roasting Common Cuts Full Brisket, Flat, Point Storage condition Must be kept at a temperature of -18 â?? Shelf life 12 months Packaging detail IWP bag, 2 kg/bag, 20kg/carton, carton designed and sticker
The colour: Black japonicum,Warm White Product configuration description 1. Product size: 400*476*865mm 2. Sheet: 15mm E1 grade double-sided chipboard packaging dimensions:480*400*870mm Gross weight: 27.5 kg(kilogram) Packaging material:The outer box is five-layer corrugated paper: 200 grams for face paper, 60 grams for medium paper, 150 grams for inner paper, and 130 grams for two layers of corrugated paper respectively; the product is shaped foam card main, 8 plastic corners, 4 paper corners , Foam cushioned flat; accessories are wrapped in cartons. 200 Pieces(MOQ)
1.PAR Lumen And Lighting Area. Height Item 60 Degree Flat Lens 90 Degree Flat Lens 120 Degree Flat lens 20cm PAR 2770 2480 2108 LUX 115860 90000 75880 Lighting Areas(©O) 0.8 1.1 1.5 50cm PAR 1625 1350 1158 LUX 65880 48000 35700 Lighting Areas(©O) 1.85 2.3 3.2 100cm PAR 768 585 462 LUX 25860 18000 10500 Lighting Areas(©O) 4.1 5.2 7.5 150cm PAR 389 285 202 LUX 10520 8000 5988 Lighting Areas(©O) 7.2 9 13 200cm PAR 265 150 98 LUX 7580 5200 3100 Lighting Areas(©O) 10.8 13.5 19 250cm PAR 148 105 82 LUX 4650 3480 2580 Lighting Areas(©O) 18.4 23 32.5 2.Parameter Model BS003 Name Gemstone Series 294x3w Size 622x430x65mm Actual Power 590-610w Input Voltage AC100~240V Output Current 650mA Output Voltage DC40~65V LED Quantity 294pcs Lifespan 50,000 Hours LED Type 3W Working Environment -20~40¡æ£¬45%~95%RH Color Red(630nm)/Blue(460nm) Working Frequency 50~60Hz N.W. 9.8kg Inner Carton Size 768x493x80mm G.W.(Inner carton) 10.9kg Outer Carton Size 780x508x180mm/2 pcs G.W.(Outer carton) 22.7kg/2pcs Standard configuration LED Light x1, Power line x1, Hanger Kits x1 Certification CE RoHS Ps: The above parameter is based on Red:Blue=8:1, for reference only
WHY CHOOSE US 1. A-share listing Master the core technology, with leading technology. 2. Large area, multi-annual The size of the average monthly output now stands at 65,000 tons, the annual output of 770,000 tons. 3. R & D strength Strong research and development, the number of patents. Product Description AL 3003 is an alloy with very good corrosion resistance and moderate strength. It is not heat treatable and develops strengthening from cold working only. Main tempers for aluminum foil 3003 includes H 18, H22, H24 and other tempers upon request. This alloy provides a better heating and cooling environment so that widely used in household applications. Mingtai Al. is a leading aluminum manufacturer mainly in business of 3003 household foil, container foil, packaging foil as well as electronic foil since 1997. Alloy: 3003 Temper: o, h12, h14, h16, h22, h24, h26 Thickness (mm): 0.015-0.2 Width (mm): 100-1600 Length (mm): C Typical products: electronic foil PRODUCT FEATURE: Mingtai Al. currently supplies 3003 aluminum foils from 0.01 to 0.20mm. Our plant equipped with flatness control system so that to ensure the precious of our foil. AL 3003 alloy is readily machined and is considered as having good machinability for the aluminum alloys. Typically, alloy 3003 is used in a number of industries. For instance, the Aluminum alloy 3003 is easily found in home appliances. From cooking utensils, bakery molds to office equipment it has many applications that you would find in your everyday lives. PRODUCTION APPLICATION 1. honeycomb foil 2. building insulation 3. packing foil 4. battery soft PACKAGING DETAILS 1. The aluminum sheet for paper or film, the surface of aluminum plate is free of scratches; 2. Plastic or kraft paper wrapped to moisture and rain, and aluminum in the transport process is clean and free of dirt; 3. Wood and steel reinforcement is installed to avoid collision in the transport process to ensure that the aluminum plate geometry unchanged; 4. Wooden boxes and brackets for packaging are marked with a fumigation of; 5. Specific packaging requirements can be satisfied according to your demands.
WHY CHOOSE US 1. A-share listing Master the core technology, with leading technology. 2. Large area, multi-annual The size of the average monthly output now stands at 65,000 tons, the annual output of 770,000 tons. 3. R & D strength Strong research and development, the number of patents. Product Description AL 3003 is an alloy with very good corrosion resistance and moderate strength. It is not heat treatable and develops strengthening from cold working only. Main tempers for aluminum foil 3003 includes H 18, H22, H24 and other tempers upon request. This alloy provides a better heating and cooling environment so that widely used in household applications. Mingtai Al. is a leading aluminum manufacturer mainly in business of 3003 household foil, container foil, packaging foil as well as electronic foil since 1997. Alloy: 3003 Temper: o, h12, h14, h16, h22, h24, h26 Thickness (mm): 0.015-0.2 Width (mm): 100-1600 Length (mm): C Typical products: electronic foil PRODUCT FEATURE: Mingtai Al. currently supplies 3003 aluminum foils from 0.01 to 0.20mm. Our plant equipped with flatness control system so that to ensure the precious of our foil. AL 3003 alloy is readily machined and is considered as having good machinability for the aluminum alloys. Typically, alloy 3003 is used in a number of industries. For instance, the Aluminum alloy 3003 is easily found in home appliances. From cooking utensils, bakery molds to office equipment it has many applications that you would find in your everyday lives. PRODUCTION APPLICATION 1. honeycomb foil 2. building insulation 3. packing foil 4. battery soft PACKAGING DETAILS 1. The aluminum sheet for paper or film, the surface of aluminum plate is free of scratches; 2. Plastic or kraft paper wrapped to moisture and rain, and aluminum in the transport process is clean and free of dirt; 3. Wood and steel reinforcement is installed to avoid collision in the transport process to ensure that the aluminum plate geometry unchanged; 4. Wooden boxes and brackets for packaging are marked with a fumigation of; 5. Specific packaging requirements can be satisfied according to your demands.
WHY CHOOSE US 1. A-share listing Master the core technology, with leading technology. 2. Large area, multi-annual The size of the average monthly output now stands at 65,000 tons, the annual output of 770,000 tons. 3. R & D strength Strong research and development, the number of patents. Product Description AL 3003 is an alloy with very good corrosion resistance and moderate strength. It is not heat treatable and develops strengthening from cold working only. Main tempers for aluminum foil 3003 includes H 18, H22, H24 and other tempers upon request. This alloy provides a better heating and cooling environment so that widely used in household applications. Mingtai Al. is a leading aluminum manufacturer mainly in business of 3003 household foil, container foil, packaging foil as well as electronic foil since 1997. Alloy: 3003 Temper: o, h12, h14, h16, h22, h24, h26 Thickness (mm): 0.015-0.2 Width (mm): 100-1600 Length (mm): C Typical products: electronic foil PRODUCT FEATURE: Mingtai Al. currently supplies 3003 aluminum foils from 0.01 to 0.20mm. Our plant equipped with flatness control system so that to ensure the precious of our foil. AL 3003 alloy is readily machined and is considered as having good machinability for the aluminum alloys. Typically, alloy 3003 is used in a number of industries. For instance, the Aluminum alloy 3003 is easily found in home appliances. From cooking utensils, bakery molds to office equipment it has many applications that you would find in your everyday lives. PRODUCTION APPLICATION 1. honeycomb foil 2. building insulation 3. packing foil 4. battery soft PACKAGING DETAILS 1. The aluminum sheet for paper or film, the surface of aluminum plate is free of scratches; 2. Plastic or kraft paper wrapped to moisture and rain, and aluminum in the transport process is clean and free of dirt; 3. Wood and steel reinforcement is installed to avoid collision in the transport process to ensure that the aluminum plate geometry unchanged; 4. Wooden boxes and brackets for packaging are marked with a fumigation of; 5. Specific packaging requirements can be satisfied according to your demands.
