Chlorinated polyethylene (CPE) is one kind of high molecule elastic material developed in late years, which is one of the random chloride produced through reaction of polyethylene and chlorine. Along with rapid development of plastic and rubber industry, its application becomes much wider. Most of them are used for Plastic and rubber processing industry. It can be solely or cross-blended with other materials to Produce plastic profile shapes, waterproof winding materials, antiflaming conveyer belts, wire and Cable covers, color bike tires and magnetic adhesive strips of refrigerator. Also, it is a kind of Perfect modifier. Properties: 1) Good aging resistance and stability 2) Perfect weather ability and can have long service life under bad weather conditions 3) Bending and cracked deformation resistance, chemical resistance and organic Solvent resistance 4) Excellent low-temperature resistance and electrical specifications 5) Superior high filling property, the physical property cannot be changed after adding A lot of filling agent into CPE Range of applications: 1) CPE generally falls into two categories: CPE and CM 2) CPE type can be used as both modifier of hard plastic product and plasticizer of Soft plastic product 3) Plastic type CPE can be used solely, and also can be cross blending processed Together with other plastic materials 4) CPE product produced by our company has the characteristics of low remnants Crystallinity and proper hardness, which makes product has certain rigidity and Does not modify its toughness
Our organization is engaged in offering a wide range of Automatic Swing Gate. All the swing gates offered by us are developed and designed using superior grade raw material in accordance with industry laid norms and guidelines. These automation swing gates are widely used in houses, offices and gardens. Further, our entire range is stringently tested on the basis of well defined quality parameters so that only high quality material is delivered at clients location within the scheduled time limit. Features: Open and close single or both the gate by remote control. With 1 point for light to be operated with same remote. Can be integrated with most of access control system (RFID, Biometric etc) Can be paired with upto 50 remote to operate the swing gate operator Safely 12volts DC motors eliminating the dangers of electric shock hazard. Overload sensor provide instant stop upon contact with obstacle. Rechargeable back-up battery for 42 hours or 30- cycles when power failure. Remote control transmitter and receiver with code encryption technology. Soft start and stop. The Swing arms are installed above the ground, eliminating common problems of water getting into the motors like underground motors have. It provides multiple mounting choices (swing in/out) Weather resistant housing (IP 54 Protection) Optional Features: Mobile App based barrier Open/ Close- Bluetooth Technology GSM based remote mobile app/ SMS/ Missed Call barrier Open/Close Long Rangle Vehicle identification and barrier Close/ Open- No waiting in queue.
---------Description--------- ! We provide installation work and operational training for all of our equipment! Fixed Crushing-Screening & Sand Washing plant is another type of mining equipment solution that is targeted for hard stone types with sandy physical composition like Riverstone, where sand separates from the stone after the crushing process and neeeded to be washed away. After completion of crushing process, the product is sorted into necessary fractions and the smallest size product is sent to the helix/screw sand washer and after to the final stockpile conveyor belt. The process of washing that begins at the vibrating screen with the use of water pump tubes at each layer, continues at the sand washer, therefore sending both sandy water and sorted product to the helix washer. Depending of initial stone size, jaw crusher can be added at the primary stage. In our case, the stone is smaller than 400 mm, therefore we use secondary impact crusher and vertical shaft impact crusher. Crushing-Screening Line consists of: Secondary Impact Crusher 1120 x 1500 mm Vertical Shaft Impact Crusher 900 mm Inclined Vibrating Screen 2000 x 6000 mm (2 pcs) 600 x 6000 mm helix sand washer (2 pcs) Main, stockpile, feedback conveyor belts All intersystem electrical cables Control panel with control system Feel Free To Contact Us For Any Additional Information!
Well logging, also known as borehole logging is the practice of making a detailed record(a well log) of the geological formations penetrted by borehol. The well logging is based on visual inspection of samples collected to the surface(geological logs) during drilling the borehole and on physical measurements made by instrument(geophysical logs). Well logging is done when drilling boreholes for groundwater is completed first stageupto required depth for geological studies Bhoojalshree specializes in geophysical well logging and has the tools for carrying out electrical logging operations since its inception in 2001, and the rich experience in well logging comes through its Director Mr. Ratilal Sudani, the personanel with the company have carried out sme well loggings in their individual capacity and requirement of the area, which has produced the favourable results. By borehole logging it is possible to identify strata as well as quality of groundwater at different depth. This type of finding helps to decide lenth of the straner pipes, sealing the aquifers having undesirable quality water etc. Well Logging is adpted in the alluvial strata, where the drilling and control is possible to get desirable quality water. To get the services for well logging the client are expected to inform the cofirmed date in well advance to avoide delay in getting services. Before starting Borehole Logging, the boring rods with bit should be taken outside of the borewhole and the water inside the bore should have minimum content of clay. The readings are starting from the water level. At each and every meter of depth four nos. of readings are observed and noted. After finishing of the survey, the noted reading are entered in computer and drawn different graphs for analysis of strata and water quality. The findings and the samples of strata taken during borehole drilling are compared and final predictions are declared. The depth of stranners and plain casing are decided on the base of the final prediction.
Introducing the GM2016 CNC Gantry Machining Center - Unleash Your Potential! Discover the ultimate solution for all your machining needs with the GM2016 CNC Gantry Machining Center. This cutting-edge marvel is designed to revolutionize your production process and accelerate your business success. With its state-of-the-art features, the GM2016 is truly a game changer. Equipped with a standard belt-driven BT50-8000rpm spindle, it offers unmatched versatility, allowing you to customize your machine with gear heads and electric spindles to meet diverse machining requirements. No matter the complexity of your project, this machine is ready to take on any challenge. Crafted with precision and strength, the frame, beam, and worktable of the GM2016 are manufactured using high-strength, top-quality cast iron. This ensures unparalleled stability, durability, and accuracy in every operation. You can rely on this machine to deliver consistent and exceptional results, time after time. But that's not all! The GM2016 features an innovative thermal cooling system for the spindle, maintaining optimal temperature conditions. This cutting-edge technology ensures consistent performance, reduces downtime, and prolongs the lifespan of the machine. With this advanced cooling system, your productivity will soar and your production process will become more efficient than ever before. Don't settle for mediocrity. Upgrade to the GM2016 CNC Gantry Machining Center and witness the power of precision and efficiency. Whether you're in the aerospace, automotive, or any other industry, this machine will enable you to exceed your production goals and unleash your true potential. Take the first step towards excellence today. Contact us now and discover how the GM2016 CNC Gantry Machining Center can transform your business. Don't miss out on this opportunity to be at the forefront of innovation and set yourself apart from the competition. Invest in success. Invest in the GM2016 CNC Gantry Machining Center.
Technical feature: Stable structure with high brazing speed(about 4.5-12 seconds needed per tooth) The electronic control system automatically from takes , changes, installs and welds, and the whole process takes 10-15 seconds. Changeover mainly by inputting data into the machine control Both sides cylinders automatically fixed saw blades to improve precision. The high frequency heating system and Ceia induction heating system control the temperature automatically. The accuracy of controlled temperature is �±1â?? to ensure brazing strength and heating stability. Automatic teeth selection, feeding, dosing, silver solder foil cutting and folding just through one-stage processing. Suitable for mass production, one person can control 12 equipment at the same time Technical description: Sorting and feeding of the carbide tips through the automatic feeder and conveyor belt. Dosing of the flux onto the carbide tips. Cutting of the silver wire or soldering platelets from a coil and stamping onto the carbide tips. Dosing of the flux onto the silver welding wire or silver brazing foil. Transferring the prepared carbide carbide tips into the ceramic-equipped and water-cooled soldering tongs. Brazing of the carbide tips onto the saw blade. Loading and unloading of the unbrazed and brazed saw blades automatically by robot system. Technical data: Diameter of saw blades 100mm-400mm Rake angle -5 +25 Carbide tips width: 1.5mm 11.5mm Brazing accuracy: 0.05mm Thickness of saw blades: 1.0mm 5.0mm Speed of brazing : 4.5 12s/per tooth General power: 6.0kw The width of silver solder foil: 1.5mm 5.0mm Water pressure : 3KG Air pressure: 5KG Electricity: 220 V single phase 50 Hz (wire bigger than 6mm2) Weight: 500KG Dimension : 1600mm *1200mm *1700mm Time of change blades 8 15s/pcs
ShoHan Semi Permanent Hair Color is a DIY unisex hair coloring system that does not requires ammonia or peroxide Thick cream base color that does not drip and colors hair for every occasion of yours Long Lasting Semi Permanent Hair Colors System with the extracts of keratin that makes your hair stronger and shinier Ready to use no mixing required Gives highlights to darker hair Available in vibrant and electric colors 100 Vegan and Cruelty Free Product GMP certified ISO and Halal certified product Available in 39 vibrant shades ShoHan Semi Permanent Hair Colorhas the following features No Ammonia No ammonia so no harsh smell No Peroxide No peroxide so no harm to hair root and shoot No bad odour Long Lasting Beautiful truetolife color which lasts up till 45 days Built In Conditioner Has built in conditioner to leave your hair conditioned and shining No Bad Odour Does not contain ammonia neither requires peroxide for application so no bad odour Luxury fragrance for pleasant smell during application and post application EconomicalPrevents waste Use what quantity is required and rest can be used in future again No Para Phenylenediamine No oxidative dyes used hence purely safe Sulphate Free No sulphates used so reduced irritation and itching on the skin Paraben Free No harmful chemicals used pure vegan product
Model: DL3020, Stroke mm: 300 * 200 * 200, Boundary dimension mm: 625 * 777 * 1080, Workbench mm: 460 * 360, Total weight (kg): 280KG, Glass bearing capacity (kg): 15, Z-axis lifting distance: 200MM, Working distance: 90 mm, Measurement accuracy UM: XY (3+L/200) um, Resolution of grating ruler: 1um, CCD resolution industrial grade: 800 line high-definition, Zoom objective magnification: 0.7-4.5X, Total magnification: 20-180 times, optional 20-220 times, Object field of view: 7-1.1MM, Surface light and contour light of the light source: white LED, with continuously adjustable brightness, Power supply: 220V �± 10%, 50 Hz. Electrical equipment requires reliable grounding: the grounding resistance is less than 4 ohms, Working environment: temperature 20 â??�± 5 â??, temperature change ï¼? 2 â??/hr, humidity 30-80%, vibration ï¼? 0.002g and lower than 15Hz, Imager characteristics: Utilize optical principles for non-contact measurement; Suitable for all fields with the purpose of two-dimensional measurement; It is the best measurement solution for small, thin, soft, and component parts; Accurate measurement can be achieved for elements such as points, lines, circles, angles, etc; And it has powerful report output function, high-quality, economical, and practical; Ultra high cost-effectiveness with all functions of flat measurement. imager: measure all plane dimensions; Hardware, main features: Fully cast aluminum worktable, column combination lightweight body. Precision transmission equipment design for fast movement. Precision P-level linear guide rail and V-shaped guide rail, with extremely high straightness, Ensure machine accuracy and service life. Sony Color CCD from Japan, with higher definition measurement images. Flexible lighting with contour light, surface light, and coaxial light (optional), high clarity, and unparalleled measurement accuracy. High precision optical ruler, every 1 micron is crucial.
CNC Lathe turning center is designed and developed for complex and high precision parts. It has the advantages of compact structure, powerful function, high machining precision positioning and preservation technology. Spindle is equipped with servo motor, repeated positioning accuracy ±0.003mm. Suitable power tools can be used for complex machining, engraving, drilling and threading, open software interface, accept standard g codes and a variety of CAM software input processing instructions. 1, the structure design of strong pertinency, mainly used for disk class, shaft class, set of class processing. 2. High rigidity, small thermal deformation, low temperature rise of the main shaft, small vibration, large cutting torque, can adapt to strong cutting. 3, the spindle adopts three-point structure, stable transmission and strength can realize a variety of grooving, drilling, reaming, reaming and boring processing. 4, the key CNC system of machine tool, spindle bearing, ball screw and other famous brands at home and abroad, so that the machine tool has high reliability. 5, CNC Lathe machine tool processing workpiece consistency is good, can stably reach IT6 ~ IT7 precision, machining surface roughness can reach Ra1.6um. 6, Adopt modular design, can provide a variety of configurations according to user requirements. 7, CNC Lathe machine tool adopts mechanical and electrical integration design, the overall layout is compact and reasonable, convenient and pleasant operation, easy maintenance.
Machine features: The function of automatically install and unload of blades, suitable for precision cutting board saw, electronic cutting saw, aluminum alloy saw blade, multi-blade saw and other series of saw blades. One person can operate more than 10 machines at the same time, greatly save labor cost. Silver solder bending unit continuously variablely programmable in all dimensions. Three groups of rails are adopted for the transmission of tungsten carbide tooth , which improves the running accuracy and service life of rails. Industrial PC with 10inch touch screen system with both language and logo for parameter setting, easy set-up and operation. Automatic teeth selection, feeding, dosing, silver solder foil cutting and folding just through one-stage processing. Welding the tip onto the circular saw blade by control the temperature so that the temperature controlled brazing and annealing cycle allows brazing joints perfectly. Automatically pick up of the brazed circular saw blade and placing it onto the upper pin of the loading magazine in ergonomic control position for the operator . Technical data: Diameter of saw blades:120mm~500mm Rake angle:-5~+25 Tip width: 1.5mm~6mm Brazing accuracy: 0.05mm Thickness of saw blades: 1.0mm~5.0mm Speed of brazing : 6~13s/per tooth General power: 6.0kw The width of silver solder foil: 1.5mm~6mm Diameter of silver wire : 0.5mm Water pressure : 3KG Air pressure: 5KG Electricity: 220 V single phase 50 Hz (wire bigger than 6mm2) Gross Weight: 800KG Dimension : 1600mm *1200mm *1700mm Time of change blades:15~20s/pcs Options: Camera inspection system Ceia induction heating system
Specifications Rated Output 80.9 kW / 110 mhp Rated Speed 3200 rpm Displacement 1.995 L / 121.7 cu. in No. of cylinders 4 cylinders Cylinder Bore x Stroke 84 mm x 90 mm / 3.31 in x 3.54 in Combustion system Direct Injection, Bosch Distributor Type VE Pump Aspiration Turbocharged & Intercooled Alternator 12V - 125A Dry weight without gear 217 kg / 478 lbs Dimensions 933 mm x 661 mm x 659 mm Controls Mechanical Certifications RCD 1 EPA Tier 2 BSO II EMC SOLAS NOTE: 1 kW = 1.3596 mhp = 1.34102 bhp Fuel condition: density at 15 C = 0.842 g/cm Technical data is according to (ISO 8665) / (ISO 3046) Fuel temperature 40 C at the inlet of the fuel injection pump (ISO 8665) Length includes KM4A2 marine gear (Dimensions may vary with other gears/elbow) Standard Engine Package Exhaust mixing elbow [L-type] Alternator 12V 125A B20 panel Flexible mounts Expansion tank for fresh water cooling system Electric stop solenoid Optional Accessories High-riser mixing elbow [instead of L-elbow] Secondary alternator 12V â 130A or 24V 75A including smart regulator C30 panel Extension wire harness [4m, 6m, 10m] Dual harness [for 2nd station] TFX Sidemount control head SOLAS including Certificate [factory fit only] Hot water kit with cocks Extension saildrive leg [75 mm] Propeller cone nut kit SD60 Air heater [glow] Trolling valve [only for KMH4A] On-board spare parts kit
PLD8000C Dynamic FPD Radiography and Fluoroscopy System Features Benefits Selfdeveloped ultrahigh frequency and high voltage generator Good Xray source Strong penetration ability Lowdose radiation Stable performance Highquality image High efficiency Flexible flat panel detector Standard highresolution dynamic flatpanel Removable dual grid Removable grid for reducing radiation Designed for pediatrics Highquality Xray tube Large heat capacity High rotate speed of Xray tube Suitable for long time and highintensity work Have long service life High Performance and Intelligent Easily ascending and descending ascend or descend ina large range low ground clearance convenient to move patients reduce patients pain Table Rises and falls freely Wide liting range special angiographic examination Lower dose to protect doctors and patients Free column movement Large Scale movement of detector radiography of different body parts Free stretching SID can electrically strech to 18m meet the needs of special clinical radiography High Performance and Intelligent Pulse fluoroscopy Instant exposure reduce image noise and improve clarity reduce the radiation dose DAP Optional Intelligent radiation dose monitoring Care for the health of patients and doctors Simultaneous monitoring with backend interconnection Automatic stitching function Optional Correction of panoramic photography reliable diagnosis basis for clinic AEC Optional High level ionization chambrer Intelligent control of exposure more efficient Intelligent control of light sensitivity Intelligent operation Intelligent workstation with humanized design Intelligent control intuitive display fficient and fast The system can be maintained remotely it can perform fault selfdiagnosis and display the fault code quickly and accurately determine the fault status and has selfprotection function lt can share information with PACS system bring benefits for remote diagnosis
Concrete Wall Panel Extrusion Machine Concrete Wall Panel Extrusion Machine Description A concrete wall panel extrusion machine is a specialized piece of equipment used in the construction industry to produce concrete wall panels through the extrusion process. It is designed to automate the manufacturing of precast concrete wall panels with consistent dimensions and high-quality surface finishes. The working principle of a concrete wall panel extrusion machine involves the following steps: Concrete mixing: The machine is equipped with a concrete mixing system that combines cement, aggregates, water, and any necessary additives or admixtures. The ingredients are mixed thoroughly to achieve a homogeneous concrete mixture. Formwork preparation: The machine has a formwork system that consists of a set of molds or templates. These molds are designed to shape the concrete into the desired dimensions and surface textures of the wall panels. The formwork is prepared by applying release agents or other treatments to facilitate easy removal of the panels later. Extrusion process: The concrete mixture is fed into a hopper or a conveyor system that transfers it to an extrusion chamber or a specially designed die. The extrusion chamber applies pressure to the concrete, forcing it through the die. As the concrete passes through the die, it takes on the shape and dimensions of the wall panel, with the desired surface patterns or textures imprinted onto it. Reinforcement and embedding: Depending on the design requirements, the machine may incorporate reinforcement elements such as steel bars or mesh into the extruded concrete. These reinforcements enhance the strength and structural integrity of the wall panels. Other embedded elements like electrical conduits or insulation materials may also be included during the extrusion process. Curing and finishing: Once the wall panels are extruded, they need to be cured to achieve the desired strength. Curing methods can include steam curing, thermal blankets, or other techniques. After curing, the panels may undergo finishing processes such as surface treatments, polishing, or the application of protective coatings to enhance their appearance and durability. Panel cutting and handling: Once the panels have achieved the required strength, they are cut to the desired lengths using cutting mechanisms integrated into the machine. The cut panels are then removed from the formwork and prepared for transportation and installation at the construction site. If you have needs, please choose Lingfeng
Up to 60 minutes runtime on a single charge with the recommended 56V 7.5Ah ARC Lithium battery (available separately) High-efficiency brushless motor delivers long runtimes, low vibration, and lifelong durability 7-position cutting height adjustments: 1.25 to 4 inches 3-in-1 function: mulching, bagging, side discharge Quick and easy push-button start 21-inch deck Bright LED headlights Adjustable handle height The EGO POWER+ 21â?? Self-Propelled Mower with Touch Drive delivers 6.0 foot-pounds of cutting torqueâ??power that exceeds gas without the noise, fuss, or fumes. Touch Drive technology puts complete control of the self-propelled system in the palm of your hands by using pressure to engage the system. Easily control the variable speed with a dial positioned at your fingertips for safe and convenient operation. This cordless lawn mower delivers up to 60 minutes of run time on a single charge with the recommended 56V 7.5Ah ARC Lithium battery (available separately). The electric lawn mower delivers precision cutting with its advanced mulching blade and seven cutting height positions from 1.25 to 4 inches, adjustable with one hand. Three-in-one functionality delivers your choice of mulching, side discharge, or bagging your grass clippings; an easy-access two-bushel grass collection bag is included. This self-propelled lawn mower includes bright LED lights for added visibility when mowing at dawn or dusk, and it folds flat for compact storage between cuts. Experience Power Beyond Belief with the EGO POWER+ 21â?? Self-Propelled Lawn Mower with Touch Drive
Overview Quick Details Type Cast iron skillet Pans Type Frying Pans & Skillets Metal Type Cast Iron Surface Finish Pre-Seasoned Color Black Brand Name Shengri or customized Certification CE / EU, FDA, LFGB Place of Origin Hebei, China (Mainland) Model Number SR379 Product Description Specification: Item number SR379A SR379B SR379C SR379D Weight(kg) 1 1.6 2.5 3.5 Size(cm) 6" L: 25.7 W: 16.2 H:4.2 8" L:31 W:21.8 H:5 10" L:39.8 W: 27.2 H:5.7 12" L:45.5 W:32.5 H:6.4 Inner Size(cm) 25.5*16*5 30.5*22.5*6 37.5*27.5*7 41.5*32.5*8 Packing Size(cm) 52*27*18 66*32*25.5 44.5*40*30.5 44*33*35.5 Qty/ctn(pcs) 10 10 6 4 Qty/20'(pcs) 11330 5200 3090 2172 Heat Source Gas, Oven,Ceramic, Electric, Induction, No-Microwave Package Customized inner box and outer carton Shipping delivery port Xingang, Tianjin Delivery date About 45 days after 30% T/T deposit paid Product Introduction This cast iron skillet 4-pc set can meet different requirements of you, made by DISA, perfect quality and fast delivery time.
Medical waste incinerator Fire print domestic waste incinerator. No fuel is required for the combustion process. Carbonized combustion does not require electricity. We separate the oxygen-rich gas from the air Help domestic garbage decompose at low temperature. Household waste incinerators do not produce flames, The chimney emits transparent gas without odor. Fire print brand waste incinerator, There is no dust in the chimney. A small amount of steam is discharged from the pipe. After cooling down, Tar recovery, Disinfection and deodorization, 2500W/220v power supply is needed to eliminate the smell of steam. Feeding mechanism power 2.2KW/380V The incinerator has a volume of 5 cubic meters of garbage, The incinerator feeds 1.8-1.0 cubes of waste at a time. Enter household garbage 3 to 4 times a day. Fire print garbage incinerator fill it with garbage. Environmentally friendly incinerator low temperature 50 to 380 â??. Need a pool of 3-5 cubic meters, Cycle cooling. The burning capacity is between 800 and 1600 kg. Output steam: wood vinegar. Output ash: ceramic ash with negative ions. Excellent reduction: 1/200 or 1/500. Fire print brand Delivery from the factory: 93000USD/piece, Need 380V/50HZ The overall container size of the equipment: length 1500cm, width 270cm, height 280cm. Green incinerator, integral container with shell, easy hoisting.
Domestic waste incinerator Fire print domestic waste incinerator. No fuel is required for the combustion process. Carbonized combustion does not require electricity. We separate the oxygen-rich gas from the air Help domestic garbage decompose at low temperature. Household waste incinerators do not produce flames, The chimney emits transparent gas without odor. Fire print brand waste incinerator, There is no dust in the chimney. A small amount of steam is discharged from the pipe. After cooling down, Tar recovery, Disinfection and deodorization, 2500W/220v power supply is needed to eliminate the smell of steam. Feeding mechanism power 2.2KW/380V The incinerator has a volume of 5 cubic meters of garbage, The incinerator feeds 1.8-1.0 cubes of waste at a time. Enter household garbage 3 to 4 times a day. Fire print garbage incinerator fill it with garbage. Environmentally friendly incinerator low temperature 50 to 380 â??. Need a pool of 3-5 cubic meters, Cycle cooling. The burning capacity is between 800 and 1600 kg. Output steam: wood vinegar. Output ash: ceramic ash with negative ions. Excellent reduction: 1/200 or 1/500. Fire print brand Delivery from the factory: 93000USD/piece, Need 380V/50HZ The overall container size of the equipment: length 1500cm, width 270cm, height 280cm. Green incinerator, integral container with shell, easy hoisting.
Island incinerator Fire print island incinerator, Fire print domestic waste incinerator. No fuel is required for the combustion process. Carbonized combustion does not require electricity. We separate the oxygen-rich gas from the air Help domestic garbage decompose at low temperature. Household waste incinerators do not produce flames, The chimney emits transparent gas without odor. Fire print brand waste incinerator, There is no dust in the chimney. A small amount of steam is discharged from the pipe. After cooling down, Tar recovery, Disinfection and deodorization, 2500W/220v power supply is needed to eliminate the smell of steam. Feeding mechanism power 2.2KW/380V The incinerator has a volume of 5 cubic meters of garbage, The incinerator feeds 1.8-1.0 cubes of waste at a time. Enter household garbage 3 to 4 times a day. Fire print garbage incinerator fill it with garbage. Environmentally friendly incinerator low temperature 50 to 380 â??. Need a pool of 3-5 cubic meters, Cycle cooling. The burning capacity is between 800 and 1600 kg. Output steam: wood vinegar. Output ash: ceramic ash with negative ions. Excellent reduction: 1/200 or 1/500. Fire print brand Delivery from the factory: 93000USD/piece, Need 380V/50HZ The overall container size of the equipment: length 1500cm, width 270cm, height 280cm. Green incinerator, integral container with shell, easy hoisting.
Oxygen-enriched incinerator Fire print oxygen-enriched incinerator, Fire print domestic waste incinerator. No fuel is required for the combustion process. Carbonized combustion does not require electricity. We separate the oxygen-rich gas from the air Help domestic garbage decompose at low temperature. Household waste incinerators do not produce flames, The chimney emits transparent gas without odor. Fire print brand waste incinerator, There is no dust in the chimney. A small amount of steam is discharged from the pipe. After cooling down, Tar recovery, Disinfection and deodorization, 2500W/220v power supply is needed to eliminate the smell of steam. Feeding mechanism power 2.2KW/380V The incinerator has a volume of 5 cubic meters of garbage, The incinerator feeds 1.8-1.0 cubes of waste at a time. Enter household garbage 3 to 4 times a day. Fire print garbage incinerator fill it with garbage. Environmentally friendly incinerator low temperature 50 to 380 â??. Need a pool of 3-5 cubic meters, Cycle cooling. The burning capacity is between 800 and 1600 kg. Output steam: wood vinegar. Output ash: ceramic ash with negative ions. Excellent reduction: 1/200 or 1/500. Fire print brand Delivery from the factory: 93000USD/piece, Need 380V/50HZ The overall container size of the equipment: length 1500cm, width 270cm, height 280cm. Green incinerator, integral container with shell, easy hoisting.
Small incinerator Fire print domestic waste incinerator. No fuel is required for the combustion process. Carbonized combustion does not require electricity. We separate the oxygen-rich gas from the air Help domestic garbage decompose at low temperature. Household waste incinerators do not produce flames, The chimney emits transparent gas without odor. Fire print brand waste incinerator, There is no dust in the chimney. A small amount of steam is discharged from the pipe. After cooling down, Tar recovery, Disinfection and deodorization, 2500W/220v power supply is needed to eliminate the smell of steam. Feeding mechanism power 2.2KW/380V The incinerator has a volume of 5 cubic meters of garbage, The incinerator feeds 1.8-1.0 cubes of waste at a time. Enter household garbage 3 to 4 times a day. Fire print garbage incinerator fill it with garbage. Environmentally friendly incinerator low temperature 50 to 380 Need a pool of 3-5 cubic meters, Cycle cooling. The burning capacity is between 800 and 1600 kg. Output steam: wood vinegar. Output ash: ceramic ash with negative ions. Excellent reduction: 1/200 or 1/500. Fire print brand Delivery from the factory: 93000USD/piece, Need 380V/50HZ The overall container size of the equipment: length 1500cm, width 270cm, height 280cm. Green incinerator, integral container with shell, easy hoisting.