Z-SG is a strain gauge signal converter. Measurements taken using the 6-wires or 4-wires technique are available through Modbus-RTU serial protocol or the analog output. Sensitivity from 1 to 64mV/V, settable by DIP-switch for integer values, via software for real/integer values by connecting to the device via the microUSB port on the front panel. Stable weight indication via Modbus register/digital output. Remote writing of the tare in volatile and/or non-volatile memory by digital input/Modbus register/Modbus commands. Z-PC-DINAL2-17.5, Z-PC-DIN2-17.5, and Z-PC-DIN8-17.5 are mandatory accessories for ModBUS configurations. TECHNICAL DATA POWER SUPPLY10..40 Vdc, 19..28 Vac (@50..60 Hz) POWER CONSUMPTION2,5 W INSULATION1.500 Vac a 3 vie ACCURACY CLASS0,01% STATUS LEDPower supply Error Tx Data Rx Data CONNECTIONSRemovable screw terminals for conductors up to 2.5 mm² MicroUSB port on front panel INTERFACESRS485 2 wires, speed up to 115.200 bps SUPPORTED PROTOCOLSModBUS RTU slave INPUT CHANNELS1 analog channel for reading (and power supply) up to 4 (350 Ω) or 8 (1,000 Ω) strain gauge load cells, 4 or 6-wire connection, equivalent impedance 87 Ω 1DI tare calibration or weight threshold OUTPUT CHANNELS1 analog retransmission channel of the net weight in current (0...20, 4...20 mA) or in voltage (0..5, 0..10 V); 1DO tare calibration or weight threshold MEASUREMENT / DIAGNOSTICSSensitivity from 1 to 64 mV/V RESOLUTION24 bit THERMAL DRIFT25 ppm/K DATA EEPROM for configuration parameters, retention time 40 years PROGRAMMINGPlug&Play configurator (EASY SETUP) System software (Z-NET4) DIP-switch
Devulcanized rubber for general rubber products. It can also be used as an asphalt modifier. Excellent tensile strength, elongation at break, Shore A Durometer properties. Samples available upon request. By compoundnig our material in a twin screw extruder, we customize the product for our customers. Our product is produced in pellet form. Unlike most devulcanized rubber, our material does not stick together.
Gm poseidon series was designed to compact containers (pet bottles, aluminum cans, etc.) gm poseidon series process vast majority of beverage packaging. So beverage manufacturers have a great demand for poseidon. Poseidon series is specialized in de-watering and compacting beverage bottles and packaging recycling. Poseidon de-water helps dry pp/pe film flakes after cleaning line, and helps screw out water in containers.As follows, p-c350 compressed pet density is 250kg/m3.
APOLO C200 is a foam recycing compactor, it can compact large size and lightweight PS materials into tight blocks at a ratio of 50:1. So that he compacted PS is easy to handle and convenient to recycle or buy or sell. It takes a screw compression technology to compress the foam, this mechanical compression technology is safe, without smoke and low consumption. Siemens Control System makes the operation easy and simple. The applicable materials include styropor, styrofoam and food trays and cups.
These high quality ball bearing hinges are made of steel and are available in multiple finishes. Enjoy the benefits of a ball-bearing hinge: Smoother operation, prevents squeaking noises, less metal-to-metal friction and longer life! Our hinges are compatible with most brands of hinges including Penrod. Product Specifications: - Steel Plated, - Includes matching screws, - 3 Holes as shown, - Gauge .085" (2.2 MM) - Typical use: 1 1/4" to 1 1/2" thick doors - Removable Pin - Sold in Pairs - Available Finishes: Satin Nickel, Oil Rubbed Bronze, Bright Brass, Antique Brass, Antique Nickel, Satin Chrome, and Polished Chrome Don't forget to purchase someextra long hinge wood screws if you are replacing your old hinges. These are specifically manufactured to help align your doors and insure that the hinges will hold in place. We have multiple finishes available including Satin Nickel, Stainless Steel, Oil Rubbed Bronze, Antique Brass, and Bright Brass.
Rotogravure cylinder making machinery: (1) The frame is made of profiled steel and a 3 steel plate, the two wall plates are made of 16mm steel plate, and the front and back of the frame are made of 10mm steel plate. The PP plate is bent and fixed with the frame. (2) the motor is driven by two side gears, the motor power is 0.4 kw, the speed ratio of the reducer is 1:10. (the parameters are designed according to the actual tightening force.) (3)30 linear guide rail and lead screw are used to drive the rear position, parallel bars are used to lift, and the shaft is used to drive the lift motor. The power of the motor is 0.75 kw.
Double head grinding machine is designed and manufactured on the basis of the Japanese grinding machine for grinding Rotogravure packaging cylinder. The whole bed is welded with steel structure and annealed under stress, the shaft, sleeve and top are quenched, quenched, phosphatized and high frequency processed, which makes the equipment have better performance and longer service life, such as linear guide track selection of Hiwin, ball screw selection of TBI are the world-famous brands, PLC, inverter, encoder, proximity switch are the preferred brand manufacturing, thus effectively ensuring the quality and service life of the whole machine.
The machine is designed and manufactured specially for grinding gravure packaging plate on the basis of Japanese grinding machine. The whole bed is welded with steel structure and annealed under stress. The shaft, sleeve and top are processed by quenching, phosphating with high frequency strictly as the drawing, which makes the equipment have better performance and longer service life. All imported parts and electrical components are used in the key parts, for example, the linear guide track applies Hiwin, ball screw applies TBI of the world-famous brands; PLC, inverter, encoder, proximity switch are the preferred brand manufacturing. Thus they effectively ensure the quality and service life of the whole machine
Automatic Shampoo Bottle Filling Capping Machine, Automatic Labeling Machine For Cream Manufacturer It is suitable filling cream, paste and viscosity liquid in cosmetic, food, beverages, medicine. Depends on the different products and various filling requests of the customers, for example, high viscosity or sticky cream, paste, such as, tomato paste, ketchup, jam, sauce, butter, chocolate paste, cosmetics cream, etc., low viscosity liquid products, such as, juice, beverage, shampoo, lotion, laundry detergent, dish detergent, wine, soybean sauce, vinegar, edible oil, cooking oil, drinking water, etc., and liquid chemical products, liquid pesticide, liquid fertilizer, liquid medicine, etc., *** Our company can design and produce suitable filling machines with matched filling system, such as, underflow pump, free-flow pump, flow-meter pump, piston pump, gear pump, screw pump, peristaltic pump, ceramic pump, electric weighs, etc., and depends on the filling volumes and production amount, the filling machines can be equipped with 1, 2, 4, 6, 8, 10, 12, 16 filling nozzles. *** The operation system with advanced PLC+ touch screen, electrical and pneumatic components can be with good quality domestic brands, joint-venture brands and imported brands, such as, WEINVIEW, SIEMENS, SCHNEIDER, MITSUBISHI, PANASONIC, AIRTAC, etc., *** The parts contact with products are made of high class SUS 304, SUS 316 and SUS 316L. Sanitary comply with GMP standard. The machines with reasonable structure, advanced technology, high precision filling, stable performances, simple and easy operation, can be used independently, and can alsoequipped with automatic bottles unscrumbler, automatic stopper pressing machine, automatic caps screwing machine, automatic caps crimping machine, automatic bottles sealing machine,automatic date/batch codes printer, automatic carton/box loading machine, to be automatic filling production line. *** With high automation degree, finished products with high qualified ratio, significantly saving manpower cost. Model No TAFM Series Name Automatic Multi Heads Liquid  Filling Machine Automatic Shampoo Filling Machine Automatic Lotion Filling Machine Automatic Liquid Detergent Filling Machine Automatic Laundry Detergent Filling Machine Automatic Liquid Soap Filling Machine Automatic Liquid Products Filler Filling Heads / nozzles Amount 2 4 6 8 10 12 16 Filling dosage 5-50ml, 50-500ml, 100-1000ml, 500-5000ml Hopper Capacity 50L--150L Filling Speed 1000-5000B/H (Depends on the filling heads amount of the filling machine, and the filling volume ) Accuracy ± 1.0%(on the base of 1000ml) Control system PLC & Touch screen Power supply AC220V 50Hz 1phase/AC380V 50HZ 3phase Air consumption 0.3-0 .7 Mpa      G.W. 450KG--1200KG Power 0.5KW--2.0KW Dimension customized
Automatic Filling Shampoo Machine For Liquid,Automatic Lotion Hair Conditioner Filling Machine,Shampoo Filling Machine It is suitable filling cream, paste and viscosity liquid in cosmetic, food, beverages, medicine. Depends on the different products and various filling requests of the customers, for example, high viscosity or sticky cream, paste, such as, tomato paste, ketchup, jam, sauce, butter, chocolate paste, cosmetics cream, etc., low viscosity liquid products, such as, juice, beverage, shampoo, lotion, laundry detergent, dish detergent, wine, soybean sauce, vinegar, edible oil, cooking oil, drinking water, etc., and liquid chemical products, liquid pesticide, liquid fertilizer, liquid medicine, etc., Our company can design and produce suitable filling machines with matched filling system, such as, underflow pump, free-flow pump, flow-meter pump, piston pump, gear pump, screw pump, peristaltic pump, ceramic pump, electric weighs, etc., and depends on the filling volumes and production amount, the filling machines can be equipped with 1, 2, 4, 6, 8, 10, 12, 16 filling nozzles. The operation system with advanced PLC+ touch screen, electrical and pneumatic components can be with good quality domestic brands, joint-venture brands and imported brands, such as, WEINVIEW, SIEMENS, SCHNEIDER, MITSUBISHI, PANASONIC, AIRTAC, etc., The parts contact with products are made of high class SUS 304, SUS 316 and SUS 316L. Sanitary comply with GMP standard. The machines with reasonable structure, advanced technology, high precision filling, stable performances, simple and easy operation, can be used independently, and can alsoequipped with automatic bottles unscrumbler, automatic stopper pressing machine, automatic caps screwing machine, automatic caps crimping machine, automatic bottles sealing machine,automatic date/batch codes printer, automatic carton/box loading machine, to be automatic filling production line. With high automation degree, finished products with high qualified ratio, significantly saving manpower cost. Model No TPAF Series Name Automatic Multi Heads Liquid  Filling Machine Automatic Shampoo Filling Machine Automatic Lotion Filling Machine Automatic Liquid Detergent Filling Machine Automatic Laundry Detergent Filling Machine Automatic Liquid Soap Filling Machine Automatic Liquid Products Filler Filling Heads / nozzles Amount 2 4 6 8 10 12 16 Filling dosage 5-50ml, 50-500ml, 100-1000ml, 500-5000ml Hopper Capacity 50L--150L Filling Speed 1000-5000B/H (Depends on the filling heads amount of the filling machine, and the filling volume ) Accuracy ± 1.0%(on the base of 1000ml) Control system PLC & Touch screen Power supply AC220V 50Hz 1phase/AC380V 50HZ 3phase Air consumption 0.3-0 .7 Mpa      G.W. 450KG--1200KG Power 0.5KW--2.0KW Dimension customized
Champion All Fleet T series engine oils are designed to provide premium performance to meet the needs of next generation of heavy-duty engines. Increased power density, reduced oil volume and extended drain intervals place unique demands on engine oils to control oxidation by-products, sludge and deposits. Due to higher shear stress and lower viscosity minimums for engine oils, only oils with the highest wear protection and viscosity stability can maximize the performance and life of advanced diesel engines. Champion All Fleet T builds on a long, trusted history protecting hard-working diesel engines. Oxidation Control- Controlling oxidation is a key performance improvement for the API engine oil upgrades. Champion All Fleet T series engine oils exceed industry and OEM oxidation performance, allowing users to achieve longer drain intervals, reduce maintenance and downtime, and extend engine life. Controlling oxidation, corrosive acids, sludge and varnish precursors allows for extended drains and minimized wear. Oxidation lower than OEM limits in over 60,000 mile on-highway and 600 hour off-highway drain intervals. Over 45% reduction in end-of-test oxidation in the new Volvo T-13 oxidation engine test. Wear Control- Champion All Fleet T series engine oils keep your engines going longer by reducing engine wear, preventing high temperature corrosion and controlling abrasive soot contamination, even while allowing for improved fuel economy and lower total cost of ownership. Over 75% less pushrod wear and 85% less injector screw wear than CJ-4 oils in proprietary, extra-severe engine testing. Outperformed corrosion bench testing limits by 70% for copper and over 98% for lead and tin. Part# 4158H/12 12/1 QT. Part# 4158N/4 4/1 Gal. Part# 4158U/2 2/2.5 Gal. Part# 4158D 5 Gal. Part# 4158AN 55 Gal.
Champion All Fleet T series engine oils are designed to provide premium performance to meet the needs of next generation of heavy-duty engines. Increased power density, reduced oil volume and extended drain intervals place unique demands on engine oils to control oxidation by-products, sludge and deposits. Due to higher shear stress and lower viscosity minimums for engine oils, only oils with the highest wear protection and viscosity stability can maximize the performance and life of advanced diesel engines. Champion All Fleet T builds on a long, trusted history protecting hard-working diesel engines. Oxidation Control- Controlling oxidation is a key performance improvement for the API engine oil upgrades. Champion All Fleet T series engine oils exceed industry and OEM oxidation performance, allowing users to achieve longer drain intervals, reduce maintenance and downtime, and extend engine life. Controlling oxidation, corrosive acids, sludge and varnish precursors allows for extended drains and minimized wear. Oxidation lower than OEM limits in over 60,000 mile on-highway and 600 hour off-highway drain intervals. Over 45% reduction in end-of-test oxidation in the new Volvo T-13 oxidation engine test. Wear Control- Champion All Fleet T series engine oils keep your engines going longer by reducing engine wear, preventing high temperature corrosion and controlling abrasive soot contamination, even while allowing for improved fuel economy and lower total cost of ownership. Over 75% less pushrod wear and 85% less injector screw wear than CJ-4 oils in proprietary, extra-severe engine testing. Outperformed corrosion bench testing limits by 70% for copper and over 98% for lead and tin. Part# 4160N/4 4/1 Gal. Part# 4160H/12 12/1 QT. Part# 4160AN 55 Gal.
Champion Blue Flame Synthetic Blend series engine oils are designed to provide industry-leading performance to meet the needs of the next generation of heavy duty engines. Increased power density, reduced oil volume and extended drain intervals place unique demands on engine oils to control oxidation by-products, sludge and deposits. Due to higher shear stress and lower viscosity minimums for engine oils, only oils with the highest wear protection and viscosity stability can maximize the performance and life of advanced diesel engines. Oxidation Control- Champion Blue Flame Synthetic Blend series engine oils take oxidation resistance to another level, allowing users to achieve longer drain intervals, reduce maintenance and downtime, and extend engine life. Controlling oxidation, corrosive acids, sludge and varnish precursors allows for extended drains and minimized wear even under the most extreme conditions. Synthetic base oils provide reduced volatility and oil consumption, further reducing the build-up of sludge and varnish. Oxidation lower than OEM limits in over 60,000 mile on-highway and 600 hour off-highway drain intervals.â?¢ Proprietary additives and synthetic base oils have shown up to 80% reduction in Volvo T-13 oxidation. Wear Control- Champion Blue Flame Synthetic Blend series engine oils keep your engines going longer by reducing engine wear, preventing high temperature corrosion and controlling abrasive soot contamination, even while allowing for improved fuel economy and lower total cost of ownership. Synthetic base oils improve cold-flow properties and reduce start-up wear, leading to extended engine life and performance. Over 75% less pushrod wear, 85% less injector screw wear and 70% better resistance to filter-plugging than CJ-4 oils in proprietary, extra-severe engine testing. Outperformed corrosion bench testing limits by 70% for copper and over 98% for lead and tin.â?¢ Cold-pumping viscosity 72% lower (SAE 15W-40) and 69% lower (SAE 10W-30) than J300 limits, providing excellent lubrication and wear protection at start Part# 4358N/4 4/1 Gal. Part# 4358U/2 2/2.5 Gal. Part# 4358AN 55 Gal.
FEATURES Aluminum body with AISI 304 screws (AISI 316 on request). Optimized passive thermal dissipation to guarantee the useful life. Possibility of inclination -5/ +10 Configuration: 4000K 70CRI (other configurations on request). L70 light maintenance > 100,ooo hours. Possibility of different photometries depending on the application. Programmable driver at fixed power. Possibility of regulation by jumps according to schedule. 10KV individual surge protection device. Independent access to both optical block and electronic components. Possibility of use with NEMA socket. RAL 9016 color (other colors on request) Weight: 7.05 lb. DESCRIPTION Possibility of mounting one pole (horizontal) or column (vertical) by means of an arm integrated into body of the luminaire. Possibility of inclination from -5 to +10. (See product installation manual
For this series, we have PP airless cylinders, AS airless cylinders. Upper and lower (airless) bottle, double spray bottle, acrylic bottle/can. Feature: Liquid does not touch the spring to avoid contamination Snap and screw Various shapes/actuators and special housings available Airless system for 360 degree distribution Large range of decoration Capacity from 5ml to 150ml Application: Travel kit. Eye cream Liquid foundation Promotional sample Lotion, cream
FEATURES Aluminum body with AISI 304 screws (AISI 316 on request). Optimized passive thermal dissipation to guarantee the useful life. Installation using a 3/4 GAS fitting (optional for mounting on a 60mm column). Configuration: 4000K 70CRI (other configurations on request). L70 light maintenance >100,ooo hours. Possibility of different photometries depending on the application. 0-10V and PWM adjustable driver and programmable at fixed power. Possibility of regulation by jumps according to schedule. Individual 20KV surge protection device. Independent access to both optical block and electronic components. RAL 9005 color (other colors on request) Weight: 18.08 lb. LED streetlight fixture with a classic and stylized design recalling circular lantern-type luminaires (Fernandina). FARO Series allows the integration of LED lighting in the historical centers of cities without causing any kind of impact as well as maintaining the aesthetics in the heritage. Mounting on an arm or column (vertical), using 3/4 GAS fitting (optional for mounting on a 60mm column). (See product installation manual) The design of the FARO Series is also ideal for parks, squares or any trail / lane illuminated by lantern type luminaires, installed on a column or wall arm facades. Available in three optimized potencies to be able to meet the demands of different enviroments or projects.
Aluminum body with AISI 304 screws (AISI 316 on request). Optimized passive thermal dissipation to guarantee the useful life. Possibility of inclination -5/ +10 Configuration: 4000K 70CRI (other configurations on request). L70 light maintenance > 100,ooo hours. Possibility of different photometries depending on the application. Programmable driver at fixed power. Possibility of regulation by jumps according to schedule. 10KV individual surge protection device. Independent access to both optical block and electronic components. Possibility of use with NEMA socket. RAL 9016 color (other colors on request) Weight: 7.05 lb. Possibility of mounting one pole (horizontal) or column (vertical) by means of an arm integrated into body of the luminaire. Possibility of inclination from -5 to +10. (See product installation manual) efficiency to offer lighting suitable for rural and urban use. TESLA Series PRO has an innovative design that brings together all the technology developed by Moonoff to offer the customer a reliable and quality option. It is the best solution to reduce the payback period of a projects investment, offering the fastest return on investment on the market. Available in optimized powers to meet the demands of the road project being illuminated.
FEATURES Aluminum body with AISI 304 screws (AISI 316 on request). Optimized passive thermal dissipation to guarantee the useful life. Possibility of inclination -5/ +15 Configuration: 4000K 70CRI (other configurations on request). L70 light maintenance >100,ooo hours. Possibility of different photometries depending on the application. 0-10V and PWM adjustable driver and programmable at fixed power. Possibility of regulation by jumps according to schedule. 10KV individual surge protection device. Independent access to both optical block and electronic components. Possibility of use with NEMA socket. RAL 9016 color (other colors on request) Weight: 14.77 lb. Possibility of mounting one pole (horizontal) or column (vertical) by means of an arm integrated into body of the luminaire. Possibility of inclination from -5 to +15. (See product installation manual ) DESCRIPTION Robust LED fixture with an aesthetic line that offers high efficiency lighting ideal for rural and urban areas. TESLA Series MAX is the high power model of the TESLA Series family, and thanks to the optimal design of its chassis, it allows it to maximize heat dissipation. It has a light source with different photometric possibilities to be able to comply with different environments presented, such as ones with great inter-distances and tall heights. Thanks to its excellent thermal management design, it can handle up to 160W, maintaining the aesthetic line and level of technical excellence of the TESLA Series family
Hydraulic gate valves are designed, manufactured, and tested in accordance with API Spec. 6A to ensure reliable and efficient operation in a variety of applications. The valves feature linear double-acting actuators that guarantee rapid opening in just 30 seconds, providing positive control during operations. Features 1. The integral forging of the valve body, along with the use of carbide alloy on the sealing surface and seats, enhances wear resistance, and corrosion resistance, and extends the service life of the valve. 2. The metal-to-metal sealing between the gate and seat, seat and body, bonnet seal, and stem backseat provides a secure, long-lasting seal. 3. The balancing lower stem of the valve allows it to stay in position even in the absence of hydraulic power, and the double-acting actuator requires hydraulic power to both open and close. Should a failure of hydraulic power occur, this valve will remain in position. 4. Balancing stem that allows the gate to stay in position unless hydraulic power is supplied to the actuator to positively open or close valve 5. Two spring-loaded, pressure-energized, nonelastomeric lip seals provide low-pressure sealing and protect against particle intrusion, while the stem seal design is capable of handling a wide range of pressures, temperatures, and fluids. 6. Stem seal design that covers a wide range of pressures, temperatures, and fluids encountered in wellhead and manifolds service metal-to-metal bonnet seal. 7. A manual locking screw maintains the gate in the closed position without any operating pressure, and socket head cap screws are used to tie down the actuator head flanges, reducing exposure to corrosive environments. Technical Parameters 1. Medium: oil and gas accompanied by sour gas or/and sand 2. Hydraulic actuator: 3,000 psi working pressure and 1/2 NPT connection 3. Rated Working Pressure: 5,000psi 20,000psi 4. Bore Size: all popular 5. Temperature: K ~ U 6. Material Classes: EE ~ HH 7. End connections: flange 8. Product Specification Level: PSL1 ~ PSL3 9. Performance Requirement: PR1, PR2
Size:600*600mm Resflor Full steel, HPL or PVC punched tile, surface punched panel which is SPCCID hard steel of Shanghai Bao steel, manual welding for the bottom square tube, origination domestic. Imported paint, conductive rim, pedestal, stringer are pressured forming with steel, lead screw could adjust height.
