1. animal feed additives, raw materials for animal feed 2. medical textile items.
D2 gas oil , diesel en590 10 ppm , light circle oil (lco) , mazut m100 , jet fuel jp54 / jet a1 , liquified petroleum gas (lpg) 60/40, 50/50 and 80/20 , d6 fuel oil, heavy fuel oil (hfo), pet coke, brazilian sugar icumsa 45.Trader
Textile items, branding clothing, garment, home textiles, carpet, shirts, hoodies, polo t-shirt, t-shirt, jacket, suits, pants, skirts, joggers, shorts.Manufacturing
Jewellery items
Gift items Orginal hand painted wooden box with gustav klimt's kiss picture. Gustav klimt's the kiss - a stunning painting with awesome power to suggest intense and exciting romance. You can use this item when you wish to energize romance luck. 16 x 13 cm
D6 is a type of residual fuel, mainly used in power plants and larger ships. The fuel requires to be preheated before it can be used. It is not possible to use it in smaller engines or vessels/vehicles where it is not possible to pre-heat it. D6 is its name in the USA. In other parts of the world it has other names. Residual means the material remaining after the more valuable cuts of crude oil have boiled off. The residue may contain various undesirable impurities including 2 percent water and one-half percent mineral soil. D6 fuel is also known as residual fuel oil (RFO), by the Navy specification of Bunker C, or by the Pacific Specification of PS-400. Recent changes in fuel quality regulation now require further refining of the D6 in order to remove the sulfur, which leads to a higher cost. Despite this recent change, D6 is still less useful because of its viscosity as well as that it needs to be pre-heated before it can be used and contains high amounts of pollutants, such as sulfur. Since it requires pre-heating, it cannot be used in small ships or boats or cars. However large ships and power plants can use the residual fuel oil.
EN590 was introduced to coincide with the development of new emissions standards across the European Union. The overall goal has been to reduce the sulphur content of diesel fuel. Sulphur had been used as a lubricant in the fuel. Its role is taken by special additives in ULSD. Since 2007, diesel that conforms to EN590 has been referred to as Ultra Low Sulphur Diesel (ULSD) in the European Union. The phrase Ultra Low Sulphur Diesel is governed by different standards in other parts of the world. EN590 describes the physical properties that all automotive diesel fuel must meet if it is to be sold in the European Union, Croatia, Iceland, Norway and Switzerland. The EN 590 had been introduced along with the European emission standards. With each of its revisions the EN 590 had been adapted to lower the sulphur content of diesel fuel since 2007 this is called ultra low sulphur diesel as the former function of sulphur as a lubricant is absent (and needs to be replaced by additives). The quality of European diesel fuels is specified by the EN 590 standard. While these specifications not are mandatory, they are observed by all fuel suppliers in Europe. Automobile diesel en 590 is intended for application in diesel engines. Diesel motor fuel quality meets the requirements of European Standard EN 590. For operation in the conditions of a temperate climate following marks of fuel diesel automobile EN 590 are offered: Grade C limiting filterability temperature -5 C; Grade D limiting filterability temperature -10 C; Grade E limiting filterability temperature 15 C; Grade F limiting filterability temperature -20 C. The entire volume of produced diesel fuel quality meets the requirements for fuels for vehicles of Euro 4 and Euro 5. Low sulfur content in diesel EN 590 reduces emissions of sulfur oxides into the atmosphere, which is especially important for for inhabitants of big cities.
It is a type of fuel created by compressing pine and wood sawdust into small forms.It does not contain any additional additives.In many areas, it is preferred over other fuel types due to its harmlessness to nature and high efficiency.Since pellets are produced in a humid environment and are compressed into very small sizes, it is possible to obtain approximately twice the energy compared to fuel equivalents (coal, etc.). Wood pellets are a fuel that is 4 to 10 times more energy dense than the energy produced by burning wood directly.