DESCRIPTION ITLS PMS 60 is a single component elastomeric sealant without isocyanates. It cures rapidly under the effect of atmospheric humidity to form a flexible and resistant joint with very good adhesion on most materials. APPLICATION ITLS PMS 60 is suitable for industrial and refrigerated trailers, truck bodies, shipbuilding, air conditioning and ventilation units, sandwich panels and other industrial applications. ITLS PMS 60 can also be used for bonding and caulking different materials used in the building industry : concrete, wood, aluminum, most lacquered metals, polyester, glass, stone, ceramic, and so on. However, for difficult materials especially lacquered or non-ferrous metals, it is necessary to make tests beforehand. INSTRUCTIONS FOR USE SUBSTRATE PREPARATION: The substrates must be clean, even, dry, free of dust, oil, grease and any contaminants that could harm bonding. All traces of poorly adherent paints or coatings should be systematically removed beforehand. They may be cleaned with PMS primer, methylethylketone (MEK) or acetone. Check the compatibility of the solvent used with the substrates. It may be necessary to rub down the substrate beforehand. After rubbing down, the surface should be recleaned. Allow the substrate to dry after degreasing. When using solvents, extinguish all sources of ignition and carefully follow the safety and handling instructions given by the manufacturer. CAULKING: ITLS PMS 60 can be applied by a manual or pneumatic gun. After application, use a putty knife to smooth the joint with soapy water. Do not apply at a temperature under 5 C. In cold weather, store the cartridges at about 20 �°C before use. This product should be used within 24 hours of opening the cartridge protection; otherwise, the sealant could harden inside. Avoid any contact with non-cured polyurethanes during curing. CLEANING: Tools can be cleaned with PMS primer, MEK or acetone before the sealant has completely cured. After curing, abrasion is necessary. STORAGE AND SHELF LIFE 12 months in the original, hermetically sealed packagings between 5 and 25 C PACKAGING 290 mL cartridges and 600 ml sausages SAFETY Not classified as hazardous. Read the material safety data sheet before use.
DESCRIPTION CC-200 is a indoor, high fluidity, rapid strength and leveling material. It still has high bonding,low shrinkage, low water absorption, acid resistance, alkyl resistance and chemical resistance. It special use for fast repairing, putty and leveling for epoxy coating. APPLICATION Floor fixing on parking garage, factory, and warehouse. Leveling before epoxy coating. Basic layer for non natural paint. Bec ause of the early strength and low moisture content, CC 200 has widely application. Contact out agent when you have doubt on CC 200. ADVANTAGES 1. Curing and enhancing are fast and rapid below 25 mins. High strength and low water absorption/ content could be reached after curing. 2. Good acid and alkyl resistance. 3. Good wear resistance, high compressive strength, leveling and anti cracking. PREPARE TO USE 1. Clean with vacuum to ensure the surface dustless. 2. Working site is free from dust, sand, oil, and loose. a). Crack and Joint Treatment b). File on the crack, open a width of 2 3 cm depth of 1 cm or more groove joints and clean up dust and loose. c). At the same time taking CC 200 mortar, filled in and up the crack and sizing 1 2 times primer after 2 4 hours. 4. Shorter wor king hours to achieve saving time, fast leveling and convenience work.
Description 1. Tough film and good adhesion on the concrete, able to penetrate into concrete. 2. Good resistance to water , brine and chemicals. Excellent mechanical strength and physical properties. 3. Good resistance to impact and abrasion. 4. Easy application , drying fast. Prepare to use 1. Mix base and hardener by the mixing ratio and Stir thoroughly, then setting at least 15 minutes. Thinner may be used to reduce viscosity. 2. Remove all foreign particles, oils, grease , rust and moistures from the surface before application. 3. Two packs product, must be used completely during the duration of its pot life. 4. Donâ??t apply when the temperature is < 10â??,>40â??, relative humidity is >90â?? or the surface temperature of substrate is not higher than the dew point for at least 3â??. 5. If the coating interval is exceeded , the surface of base coat must be roughened to insure adhesion. 6. Keep away from heat, sparks and flame. 7. Stored with good ventilation. 8. Keep adequate ventilation during application. 9. The actual coverage may vary, depending on application technique, job conditions and type of surface. Under brushing & rolling application the actual coverage is estimated at 70% of the Theoretical coverage and 60% for spraying. **The parts of data base above could be affect by application condition at job site, please reference guide specification or contact with relative technical personnel. Color : Clear Drying time : Tack-free : 2 hours Hardness : 8 hours Full cure : 7 days (grease)
DESCRIPTION CP-310 was synthesized from imported high-technology macromolecule resin and specialized paint that is different from general acrylic resin. CP-310 is a perfect product to provide a high water-tolerant, climate-tolerant, and anti-UV ability. FEATURES * Excellent environmental water-based waterproofing paint * Water-based, Non-toxic, odorless, inflammable, and harmless * Fine adhesion, extreme toughness, high elastic, and high endurance * Hydrophilic, and may be applied on damp surface USE RoofBuilding, condominium, factory, barracks, school, garden and etc.. WallsBasement wall , exterior wall , and etcâ?¦ PREPARATION 1. (The following steps are recommended for best results) 2. New concrete must cure for a minimum of 30 days 3. All holes or cracks must be properly patched 4. All surfaces must be clean and free of dirt, dust, efflorescence and oil APPLICATION (The following steps are recommended for best results) 1. Stir well before use. Do not thin; however, if thinning is necessary, thin water at a rate of no more than 10% 2. One prime required CP-310 primer 3. Two coats are required for the best resultskeep the thickness of each coating below 1m. 4. Wait for each coating to be total dry before overlaying the next coat. The interval time between each coating is minimum of 8 hours. COVERAGE 5-gallons about 33m2 COLOR Grayã??Whiteã??ivoryã??Green DRY TIME Dries to touch in about 1-2days . Low temperatures or high humidity conditions will affect drying time. Full cure should be reached in 14-30 days. CLEAN UP 1. Clean hands and tools with soap water. 2. After 30 days or paint has fully cured, areas may be wasted using a non-abrasive, mild detergent and cellulose sponge. WARNING (Read the following carefully for your own safety) 1. Keep out of reach of children-Do not take internally. 2. May cause eye, skin and respiratory tract irritation. May be harmful if swallowed. Use only with adequate ventilation.
DESCRIPION FR-48 is solvent-less moisture cure type, single-component flame retardant RTV silicone product. It is suggested for use in applications requiring neutral cure, fast cure and excellent adhesion. FEATURES * Sealing of electrical components * Industrial plastic sealing, electrical insulation properties. * Low flammability â?? has a UL rating of V-0(1) * Primerless adhesion to plastics and metals * Excellent resistance to moisture, dust, UV and ozone. * Fast room temperature curing * High temperature resistance (Flexible from -60â?? to 200â?? continuous operation and 260â?? for short periods) COMPATIBILITY FR-48 contamination -free silicone sealant shows excellent adhesion for Al panel, stone, glass, PVC, or wood. As new construction materials appear and the material surface treatment method varies, some materials may cause poor adhesion or discoloration. FR-48 contamination-free silicone sealant is chemically stabilized, maintains a uniform paste shape all the time, and may be workable at the temperature range of -25â??~50â?? unless there is moisture. LIMITATION * For structural construction * At completely enclosed space * On frosty or wet target surfaces * For the parts with potential continuous flooding * In the internal fire area * For materials where oil, plasticizer, or other solvent is leaking. * For polypropylene, polyethylene, polycarbonate, or Teflon material. * At horizontal : joints potential physical friction * For the parts requiring painting on the sealant * For materials with surface temperature over 50â?? PACKING 300ml Cartridge COLOR White and grey STORAGE Shelf life is 1 year if stored unpacked in cool and dry condition away from direct sunlight.
Automatic nut tapping machine, nut tapping machine, tapping machine Hnt is suitable for hexagon, square, flange and nylon nut. Hnt can reach longer tapping stroke requirement while tapping longer or harder nuts. The operation panel is easy to understand and each spindle can be operated independent. Right or left tapping can be selected, tap life setting and adjust the tapping distance all can set up on the operation panel. Programmable language controller (plc) is used in the machine to monitor and control all tapping actions which can carry some functions including each spindle output counter is independent, operating automatically or manually, adjustable tapping speed, tapping error alarm of each spindle and motor overload alarm. Examination by current meter can detect tapping abnormal, jammed nuts during feeding or empty tapping, which can avoid tools get damage. The replacement of tools is simple and saving time. Magnetic chip filter maintain tapping oil is clean away the chips. Hnt is designed for safety consideration and qualified by ce. Hexagon thin castle nuts: din 937, 979 Hexagon thin nuts: din 439, 936 Hexagon nuts: din 555, 934, 971, 2510, 6915 Lock nuts: din 980, 982, 985, 6924, 6925, 6926, 6927 Square weld nuts: din 928, 929 Square nuts: din 557 Square thin nuts: din 562 Hexagon castle nuts: din 935 Hexagon nuts with flange: din 6923
Copper cathodes, aluminium ingots, frozen meat, frozen poultry, coal, gas oil, lng.Purchaser, distributor, importer/exporter
Activated Carbon, Potassium Nitrate, Trichloroethylene, Tetrachloroethylene, Hydrogen Peroxide Solution..
Foundry materials, lubricating oil.
Therapeutic grade essential oils.
Bitumen.
Robusta Green Coffee Beans.
used in the circulating cooling water of thermal power plants and oil refineries, and the oil field reinjection water system, which can reduce the corrosion and scaling of metal equipment or pipelines.
Commodity, special electronic devices, and petroleum products..International trading, supply and distribution of the said products
Diesel en590 10ppm.
En 590.
Diesel en 590 10 ppm.
Metal scrap and petroleum products.
Mung beans, butter, fishmeal, hemoglobin powder.
Infusion type 100% pure rice noodles (sesame oil and ginger puree), infusion type 100% pure rice noodles (vegetarian diet).
