Description CS-613 is a multipurpose water-based epoxy sealer/putty/adhesive. Itâ??s developed for filling seam, gap between Calcium Silicate board. It is environmentally friendly which does not pose health hazard to user and dwellers. The best part is how easy it can be cleaned with just water. Itâ??s easy to mix even by hand due to our innovative water-based technology. Features / Benefits *Paintable easily with water-based coating; can be painted after 1 day without work delay hence reduce time and save money. * Easy to use: Compatible with damp surface, time is saved in waiting for it to dry up; Washable with water including tools. Best to wash as soon as possible before it hardens. * Smooth to tool with trowel; Non-sagging characteristic making it easy to use on vertical wall and ceiling. * Stronger adhesion due to higher amount of binders used. * High solid by volume; 100% water resistant when cured. * Low odor/ solvent free/ VOC free, it does not pose health hazard to user and dwellers.
DESCRIPTION ITLS PMS 60 is a single component elastomeric sealant without isocyanates. It cures rapidly under the effect of atmospheric humidity to form a flexible and resistant joint with very good adhesion on most materials. APPLICATION ITLS PMS 60 is suitable for industrial and refrigerated trailers, truck bodies, shipbuilding, air conditioning and ventilation units, sandwich panels and other industrial applications. ITLS PMS 60 can also be used for bonding and caulking different materials used in the building industry : concrete, wood, aluminum, most lacquered metals, polyester, glass, stone, ceramic, and so on. However, for difficult materials especially lacquered or non-ferrous metals, it is necessary to make tests beforehand. INSTRUCTIONS FOR USE SUBSTRATE PREPARATION: The substrates must be clean, even, dry, free of dust, oil, grease and any contaminants that could harm bonding. All traces of poorly adherent paints or coatings should be systematically removed beforehand. They may be cleaned with PMS primer, methylethylketone (MEK) or acetone. Check the compatibility of the solvent used with the substrates. It may be necessary to rub down the substrate beforehand. After rubbing down, the surface should be recleaned. Allow the substrate to dry after degreasing. When using solvents, extinguish all sources of ignition and carefully follow the safety and handling instructions given by the manufacturer. CAULKING: ITLS PMS 60 can be applied by a manual or pneumatic gun. After application, use a putty knife to smooth the joint with soapy water. Do not apply at a temperature under 5 C. In cold weather, store the cartridges at about 20 �°C before use. This product should be used within 24 hours of opening the cartridge protection; otherwise, the sealant could harden inside. Avoid any contact with non-cured polyurethanes during curing. CLEANING: Tools can be cleaned with PMS primer, MEK or acetone before the sealant has completely cured. After curing, abrasion is necessary. STORAGE AND SHELF LIFE 12 months in the original, hermetically sealed packagings between 5 and 25 C PACKAGING 290 mL cartridges and 600 ml sausages SAFETY Not classified as hazardous. Read the material safety data sheet before use.
DESCRIPTION CC-200 is a indoor, high fluidity, rapid strength and leveling material. It still has high bonding,low shrinkage, low water absorption, acid resistance, alkyl resistance and chemical resistance. It special use for fast repairing, putty and leveling for epoxy coating. APPLICATION Floor fixing on parking garage, factory, and warehouse. Leveling before epoxy coating. Basic layer for non natural paint. Bec ause of the early strength and low moisture content, CC 200 has widely application. Contact out agent when you have doubt on CC 200. ADVANTAGES 1. Curing and enhancing are fast and rapid below 25 mins. High strength and low water absorption/ content could be reached after curing. 2. Good acid and alkyl resistance. 3. Good wear resistance, high compressive strength, leveling and anti cracking. PREPARE TO USE 1. Clean with vacuum to ensure the surface dustless. 2. Working site is free from dust, sand, oil, and loose. a). Crack and Joint Treatment b). File on the crack, open a width of 2 3 cm depth of 1 cm or more groove joints and clean up dust and loose. c). At the same time taking CC 200 mortar, filled in and up the crack and sizing 1 2 times primer after 2 4 hours. 4. Shorter wor king hours to achieve saving time, fast leveling and convenience work.
DESCRIPION FR-48 is solvent-less moisture cure type, single-component flame retardant RTV silicone product. It is suggested for use in applications requiring neutral cure, fast cure and excellent adhesion. FEATURES * Sealing of electrical components * Industrial plastic sealing, electrical insulation properties. * Low flammability â?? has a UL rating of V-0(1) * Primerless adhesion to plastics and metals * Excellent resistance to moisture, dust, UV and ozone. * Fast room temperature curing * High temperature resistance (Flexible from -60â?? to 200â?? continuous operation and 260â?? for short periods) COMPATIBILITY FR-48 contamination -free silicone sealant shows excellent adhesion for Al panel, stone, glass, PVC, or wood. As new construction materials appear and the material surface treatment method varies, some materials may cause poor adhesion or discoloration. FR-48 contamination-free silicone sealant is chemically stabilized, maintains a uniform paste shape all the time, and may be workable at the temperature range of -25â??~50â?? unless there is moisture. LIMITATION * For structural construction * At completely enclosed space * On frosty or wet target surfaces * For the parts with potential continuous flooding * In the internal fire area * For materials where oil, plasticizer, or other solvent is leaking. * For polypropylene, polyethylene, polycarbonate, or Teflon material. * At horizontal : joints potential physical friction * For the parts requiring painting on the sealant * For materials with surface temperature over 50â?? PACKING 300ml Cartridge COLOR White and grey STORAGE Shelf life is 1 year if stored unpacked in cool and dry condition away from direct sunlight.
Peelable Coating.
Meat And Bone Meal .
Ito coated glass, metal coating, ito coating.
Hand tools, vehicle repair tools, garden tools, measuring tool, mounted stone, pneumatic tool, thermal insulation coatings, pet accessories..
