DESCRIPTION CC-103(2K) Crystalline Waterproofing Materials is a capillary waterproofing formulation. CC-103(2K) has high permeability which crystallize and penetrate deeply into the capillaries of the concrete. ADVANTAGES * Applied to wet surface * Transparent, non-toxic and odorless * High cohesion and effective against positive/negative water pressure well APPLICATION * The leakage of inner wall in basements or the protection against positive/negative water pressure * Prevent seepage and leakage in underground passages and tunnels * Avoid the leakage of cisterns and pools PACKING 30KG/Set A: 22.5KG in powder.+ B: 7.5KG additive. COLOR Grey and white. STORAGE 6 months in original container stored in dry conditions and under 25°C.
Description CP-121W(14) is suitable for new and old concrete floor with resistance and waterproofing ability. It has ability to penetrate in concrete, plaster or the surface of the stone for the building and to reach waterproofing. * Able to apply on the damp surface * Odourless and eco-friendly * Excellent resistance ability of negative water pressure (Comply with CNS1232. CNS10460. ASTM E96-12 B) * Enhance adhesion strength Properties * Leaking stoppage from basement inner wall * Waterproofing on negative water pressure * Anti-seepage for underpass, tunnel and water tank Application 1. Clean the surface to be free from loose particle, dirt and oil. 2. 3 options for application
DESCRIPTION Instant cement as material for leveling concrete floor which required high flatness level. With base elements of cement, selected sand, filler and additive all of which homogenously mixed. ADVANTAGES * Easy and ready to use, by water addition only. * Fast working * Practical and high adhesive power * Floor would be flat/ level in a second APPLICATION CA-010 is used as a floor screed material surface that canâ??t be exposed and should be covered with floor material, such as: ceramic, granite, carpet, parquet and other materials.
DESCRIPTION Non-Skinning sealant is a one component, non-drying polybutene rubber based mastic. It does not harden but rather remains permanently soft and paste-like. Non-Skinning sealant has excellent resistance to water vapor transmission. FEATURES * Permanently non-skinning * Low shrinkage * Moisture resistance * Excellent adhesion USES * It is suitable for all kinds of plastics, metals, glass, masonry and timber. * It can also be used in installation of cool rooms and prefabricated construction. LIMITATIONS * It should not be applied in exposed joints where dirt pick-up and hand contact. * Not for: Used in areas subject to considerate dynamic stress. * Not for: Mobile homes, truck bodies. COLOR White, almond other colors are available upon request. APPLICATION * Surface must be clean and dry. * Cut nozzle to desired size. * Insert cartridge into caulking gun. * Push sealant ahead for uniform bead. * Clean off excess sealant with kerosene or mineral spirits. CAUTION Use appropriate personal protection to avoid contact with skin and eyes. In case of eye contact, flush with copious amounts of water for at least 15 minutes and get medical attention. In case of skin contact, wash affected areas with hand cleaner followed by soap and water. For further information, please refer to Material Safety Data Sheet (MSDS).
DESCRIPTION CC-102 Concrete Hardener is a clear high performance waterborne liquid which being applied to the floor and absorbed into the concrete pores and reacts with the calcium salts effectively making the concrete surface denser and considerably less porous. APPLICATIONS Suitable for improving the quality of concrete floors in factories, warehouse and any other area where hard non-dusting floors are important. SURFACE PREPARATION Surfaces should not have had previous treatments. They should be firm and free from oil, dirt, dust etc. Weak spots should be cut out and filled with CEMCRETEâ??S FLOOR PATCHING. All surfaces to be dry at time of application. MIXING AND APPLICATION Shake or roll drum to thoroughly mix contents. Apply HARDENER to the dry surface using a soft household broom or paint roller. Application should be liberal but it is advisable to brush away unabsorbed pools immediately to avoid the HARDENER forming glassy layers. Allow one day between coats. Two coats are usually sufficient, but a third might be required if the concrete is very porous SPECIMEN FINISH A trial area should be treated on site for the Engineerâ??s or Architectâ??s approval. COVERAGE Depends upon the suction and texture of the surface. Approximately 6m2 / litre/coat.
ITLS-RB is a flexible high-performance sound barrier. It is a low-stiffness material which improves the sound transmission loss by effectively blocking noise. ITLS-RB has a reinforced backing to further enhance its mechanical strength. It is designed for hanging-up applications where the material is typical used as an acoustic curtain. ITLS-RB is a high temperatures resistant noise barrier. It provides excellent soundproofing effect at a wide range of temperatures, typically from -40°C to +140°C, where other traditional noise barriers would fail. ITLS-RB meets with GM Holden specification HN2483 requirements. Key Features *Durable & flexible *Suitable for hung-up applications *Easily cut, fabricated and installed *Contains no lead, non toxic *May be stapled or nailed into position *Suitable for elevated temperatures up to 140°C(Intermittent) Key Benefits *Proven soundproofing performance *Economical *Low installation cost *Easy to handle
Product Features : 1.Strong adhesion and economical choice. 2.Quick setting and curing time. 3.Easy and quick use. 4.Suitable for dry fastening. 5.Suitable for wall and overhead application. 6.Reduced anchor spacing and edge distance. 7.Variety of cartridge sizes are available. 8.Partially used cartridges can re-used by replacing the mixer nozzle. Base Material : Concrete,solid masonry ,and hollow bricks masonry. Application : Fixing machines,handrails,steel constructions,and reinforcement bars. Shelf Life : 12 months after the manufactured day if stored in perfect conditions.
Dual functions Fast drying 2 in 1 -adhesive sealant Faster and higher green strength than solvent based construction high strength formed after 5 hrs. Water-based construction adhesive is developed to serve as adhesive and sealant give good wet grab. The adhesive is tough but also flexible. Developed for both professional and home handy man using AFTEK own new technology. 1. Fast setting 2. Very Tough but flexible with good degree elasticity 3. High heat resistance better than solvent based adhesive 4. Plasticizer resistant 5. No Sagging No sliding on smooth surface, can use on ceiling 6. No Drooling, no wastage and no mess on floor to clean up 7. High wet grab good for sticking heavy tiles and not slippery. 8. Easy to extrude even on cold day. Features: * Almost odorless. * NO VOC safe to use indoor. * Exceptional fast bond development. * Creamy smooth easy to spread. * Highly thixotropic easy to use on wall and ceiling without dropping off. * Good gap filling properties-suitable for filling uneven surface or small crack due to high solid content. * Paintable when dry. Product Specification: Highest Solid by weightâ?? 82% -83% few if any can match it. * SG â?? 1.65 â?? low filler surface area more binder for better adhesion. * pH 6 â??7 â??Near neutral safe on substrates. * No caustic soda or ammonia safe to use at home. * 5 hours bond strength 2.0 kg force/cm2 * After 24 hrs Bond strength 22 kg force/ cm2 no other WB adhesives can match that. Clean Up Clean up tool as soon as possible with water before it set hard. For harden adhesive, scrap off as much as possible with a strong scraper. Use solvent such as mineral turp to soften the remaining adhesive. Shelf life â?? I year if kept at ambient temperature within 5â?°C - 35â?°C.
DESCRIPTION CC-700 is a 100% solid content, two components, high performance polyurea elastomer based on aromatic MDI and amine-terminate Polyether. It displays extremely fast cure times about 10-100 seconds and shrinkage resistance which also provides excellent acid, alkali and chemical resistance. WORKING PROCEDURE 1. Surface preparation - please make sure the surface in clean, dry, sound and smooth condition. 2. Crack repair â?? Epoxy resin mortar, Epoxy resin repair material, single component polyurethane sealant and single component polyurethane waterproofing material. 3. Primer 4. Application â?? 2.1-2.5kg per 2mm thickness. (1.3kg of CC-700 could be applied 1mm thick) 5. Top coat CHARATERISTIC 1. Well abrasion resistance, flexibility and elasticity. 2. Corrosion resistance 3. No building restriction, wide working temperature range. None sensitive to temperature and humidity, it can be harden at 5â??. It can be applied in -40â?? ~ 120â??. 4. Environmental protection and high solid content. 5. Non-sagging and seamless, can be used over flat or vertical surface at the same time. 6. Excellent adhesion to a wide range of substrates.
DESCRIPTION * Environmental friendly water-based paints,safe and non-toxic. * Suitable for indoor/outdoor excel wall. * High performance waterproofing application, excellent permeability, and corrosion resisting. * Resist to mold,weather and chemical resistance. * Fast drying and no irritating smell, Expoy is substituted by CC105. * Apply in multiple layers with smooth surfaces. APPLICATIONS * Floor or excel wall fixing on Parking Lot,Mall,and home used. * Industrial factory and white room. * Excellent permeability and enhanced water resistance, Can be used in wet and fouling protection areas. * Used as waterproofing coating and burnish surface coating. PACKING AND STORAGES * 20 kg/pail * The amount of raw 0.1~0.15 kg/m2 (twice usage) * keep the storage environment well ventilated area. Less than 25 degrees can be stored for 6 months.
DESCRIPTION ITSEAL is truly developed for sealing window frames with highly durable and flexible properties to withstand severe weathering and extreme temperatures. It seals small gap that normal sealant cannot reach and penetrate. It provides a truly watertight seal deep into minute joint and gap. FEATURES * ITSEAL is the only waterproof sealer that is completely watertight. * It is highly water repellent that no water can get through it during storm. * It adheres well on aluminum and glass * Once dried, ITSEAL is flexible and accommodate joint movement due to vibration. * Mill finish aluminum, oil or wet surfaces can also be well-sealed. VOC CONTENT Type of Regulated Adhesive under the Air Pollution Control (Volatile Organic Compounds) Regulation of Hong Kong: Architectural Sealant VOC Content (Ready to use): 248g/Ltr. SURFACE PREPARATION For maximum adhesion, the adhesive surface must be free of dust, release agent, oil and grease. Wipe surface with solvent is recommended. Solvent are obtainable from ITLS-SB. This information in this catalogue is provided to the best of our knowledge from results gathered both internal and external credited laboratories. However, we have no control over site applications, site conditions and workmanship of the applicator. We therefore will not accept any liability, either directly or indirectly arising from the misuse of these products or when the product is used not in accordance with any advice, specification, and recommendation of information given by us, The user is responsible for checking the suitability of these products for its intended use. APPLICATION ITSEAL can be used with hand operated or air operated grease pump. Other simple extruding device can also be used but it has to be solvent resistance. LIMITATION * Not suitable large gap wider than 5 mm wide and deep. For deeper joint fill to half of it, let it dry overnight and fill it up the next day. * Not suitable for use as expansion joint. COLOUR AND PACKING 26 kg / pail Grey/Black/Bronze/White SAFETY INFORMATION * ITSEAL is flammable. Please keep away from sources of ignition during application. * Avoid breathing in solvent by wearing solvent vapor respiratory mask in badly ventilated area or confined space. * Avoid contact with skin and eyes. If swallowed please contact doctor immediately. * ITSEAL meets the requirement of RoHS regulation of European Union and it does not contain eight heavy metals which were restricted by ASTM F963 or EN71 part3. * Please read the Material Safety Data Sheet in regards to flammability and health and hazard. SHIPPING/STORAGE INFORMATION ITSEAL must be stored in a cool place under 25°C and away from direct sunlight. The shelve life is 12 months if stored in accordance to the recommendation. Dangerous Goods Information: Cement Adhesive, Class 3, UN1133 PG III.
DESCRIPTION ITLS simplySEAL Concrete Seal is a high performance waterborne acrylic coating which provides a protective and decorative seal for concrete and masonry. Suitable for use on new and old concrete. USE * Suitable for use on concrete, bricks, pattern paving, pebble finishes (including exposed aggregate pavements), clay pavers, masonry, sandstone, slate, and unglazed tiles, * Exterior driveways, carparks, pavements, pavers, patios, overlays. Interior residential, commercial, and light industrial factory and warehouse floors. FEATURES & BENEFITS * Low VOC (
DESCRIPION FR-48 is solvent-less moisture cure type, single-component flame retardant RTV silicone product. It is suggested for use in applications requiring neutral cure, fast cure and excellent adhesion. FEATURES * Sealing of electrical components * Industrial plastic sealing, electrical insulation properties. * Low flammability â?? has a UL rating of V-0(1) * Primerless adhesion to plastics and metals * Excellent resistance to moisture, dust, UV and ozone. * Fast room temperature curing * High temperature resistance (Flexible from -60â?? to 200â?? continuous operation and 260â?? for short periods) COMPATIBILITY FR-48 contamination -free silicone sealant shows excellent adhesion for Al panel, stone, glass, PVC, or wood. As new construction materials appear and the material surface treatment method varies, some materials may cause poor adhesion or discoloration. FR-48 contamination-free silicone sealant is chemically stabilized, maintains a uniform paste shape all the time, and may be workable at the temperature range of -25â??~50â?? unless there is moisture. LIMITATION * For structural construction * At completely enclosed space * On frosty or wet target surfaces * For the parts with potential continuous flooding * In the internal fire area * For materials where oil, plasticizer, or other solvent is leaking. * For polypropylene, polyethylene, polycarbonate, or Teflon material. * At horizontal : joints potential physical friction * For the parts requiring painting on the sealant * For materials with surface temperature over 50â?? PACKING 300ml Cartridge COLOR White and grey STORAGE Shelf life is 1 year if stored unpacked in cool and dry condition away from direct sunlight.
PREPARATIONS This product is waterproofing, heat insulated, breathable compound materials. It is made from versatility graded sand, lightweight aggregate, water-proofing resin and variety of additives. FEATURES * To retain waterproofing, heat insulated, breathable through one-time application. * With excellent adhesion, non-sagging and construction resistance. * Without cracking and bulging after curing. * Applying by manual and mechanical efficiently. APPLICATIONS * With painting and leveling on the indoor, outdoor and bathroom wall. * With painting and leveling on roofing insulation. * With painting and leveling on metal mesh. * To repair the surface of the roof ceiling.
DESCRIPTION Hydrostatic press stone filmless maintenance agent is a maintenance hybrid comprised of a special kind of Oligomer Silsesquiloxane mixed in a water-based solution, formulated with powerful surfactants attributing to its excellent-resistance properties and a non-yellowing methyl silane hybrid, which reacts with the moisture and CO2 in the air, forming a nonsolvent based resin that penetrates into the substrate heightening its water proofing ability. Its ability to penetrate deep into the concrete, as deep as 3~5m/m, distinguishes it from other products on the market. Moreover, it can cause a chemical reaction with alkaline materials that produces crystals inside the concrete, that can fill and block the micro-vein within the concrete so as to reach the waterproof effect in depth; thus, the longevity of the building can be extended. APPLICATION Water, anti-pollutants and anti-weathering resistance for various surfaces such as: tiles, gaps between tiles, terra cotta, calcium silicate board , plasterboard ,bricks,concrete, natural and process stone, stone carving, stone washing, stone smoothening, stone cutting,sidewalks, parking plywood. ADVANTAGES * Highly active molecule that is eco-friendly, water-based and inorganic produces strong adhesive to the substrate after chemical cross-linking. * High permeability and excellent durability. * Non-yellowing, no stain contaminated, dirt can be easily washed off with water from rain or washing walls. * Excellent water repellent ability (the so-called Lotus effect) can effectively prevent from water permeating. * It is suggested to apply new coat regularly every three years; thus it can continue to maintain water-repellent and anti-pollutant functions.
DESCRIPTION Is a cement based waterproofing slurry which contains a high quality polymer and selected filler such as silica sand and other additives. When it dry will provide a hard and abrasion resistant waterproofing layer which can be tiled over sucessfully. USES IN APPLICATIONS * Is suitable to make a protection waterproofing layer on * Bathroom, Kitchen & Laundry Area * Balconies & Terraces * Water Tank / Water Reservoir * External Wall FEATURE & BENEFIT It can be used as underlayment to prevent water seepage from the ground before laying marble, granite, natural stone, timber floor, carpet and vinyl. DAMPSCOAT SL is compatible with concrete and any mixture of cement-sand rendering or plastering. After dry, it can be painted over with any water or solvent based paint.
*Works on wet,dry,dirty or corroded pipe *Works under salt or fresh water *Works on any metal or plastic pipe *Cures in 10~15 minutes *No tools needed *Impervious to water,oils,chemicals,solvents&acids
DESCRIPTION Doctor-sil 792 is a high performance, weatherable product and suitable for various interior/exterior joint sealing, glazing, and curtain-wall. It is designed to have 50% movement capability, superior durability, weather ability and adhesion. Especially, it is a low modulus product which can efficiently cope with shrinkage/swelling on joint having superior elongation ratio. FEATURES AND ADVANTAGES * Low modulus product specially designed for new building joint. * Superior bonding strength on various substrates without primer. * Easy application with one component. * Easy installation with good extrusive property. * Superior weather ability and durability. APPLICATIONS * Window & Window Frame Joint Sealing * Interior/Exterior Joint Sealing * Aluminum Frame Assembling * Curtain Wall Joint Sealing
DESCRIPTION Gap Filler is a multi-purpose and high quality sealant. It is composed of environmentally friendly water-base polymer emulsion and inorganic filler. It is smooth, flexible and easy to use after curing prevents cracking. APPLICATION * It forms an airtight seal to prevent air and moisture when applied to surfaces such as wood, brick, masonry, drywall, concrete, ceramic tile and glass. * It is ideal for sealing seams, joints and cracks around windows, door, siding, woodwork and air conditioners. * Please do not use for adhesion or sealing of glass or structures unit.
DESCRIPTION Doctor-Sil829 is single component type acetoxy silicone sealant. As it excels in weatherproofing, durability, adhesion, and constructability, it may be used for various construction parts including windows and glasses. * Good weatherproofing and durability. * Maintains good flexibility * Excellent adhesion to concrete most metals and plastics APPLICATION * Metal, aluminium, glass, wood, resin, ceramic and fiber