ATon tea, Top 10 Souvenir of 2022 Across Asia Pacific, blended by EU verified German Herbs and HALAL certified Taiwan Ali-Mountain Oolong tea, includes Morning, Afternoon, Evening and Weekend tea. With the combinations of Western and Eastern tastes, ATon tea yields unique multi-mellow smooth and marvelous tastes, the lingering aftertaste and natural sweetness from our Ali Mt. Oolong makes ATon tea stand out from the market. ATon tea is a new concept of natural healthcare by using multiple ingredients as well as the trend-leading, patented packaging designs plus our funny and positive brand mascot have made ATon develop a unique stylish manner in this highly competitive tea market and attract more young people as well.
Description CS-264 is the latest innovative Contact adhesive using our home-grown technology. This is the only Contact adhesives with 50% solid. It's cost effective with the highest active ingredients. Less solvent less health hazard. CS-264 is made of tough elastomeric rubber, tackifying resins and solvent with least odour without toluene. Features Faster sticking Contact Adhesive within 5 minute. Strong grab on contact with higher green strength. Paintable when dried. Easy to extrude even at -15 C , most suitable for all season. Very Low odour without toluene.
DESCRIPTION CP-310 was synthesized from imported high-technology macromolecule resin and specialized paint that is different from general acrylic resin. CP-310 is a perfect product to provide a high water-tolerant, climate-tolerant, and anti-UV ability. FEATURES * Excellent environmental water-based waterproofing paint * Water-based, Non-toxic, odorless, inflammable, and harmless * Fine adhesion, extreme toughness, high elastic, and high endurance * Hydrophilic, and may be applied on damp surface USE RoofBuilding, condominium, factory, barracks, school, garden and etc.. WallsBasement wall , exterior wall , and etcâ?¦ PREPARATION 1. (The following steps are recommended for best results) 2. New concrete must cure for a minimum of 30 days 3. All holes or cracks must be properly patched 4. All surfaces must be clean and free of dirt, dust, efflorescence and oil APPLICATION (The following steps are recommended for best results) 1. Stir well before use. Do not thin; however, if thinning is necessary, thin water at a rate of no more than 10% 2. One prime required CP-310 primer 3. Two coats are required for the best resultskeep the thickness of each coating below 1m. 4. Wait for each coating to be total dry before overlaying the next coat. The interval time between each coating is minimum of 8 hours. COVERAGE 5-gallons about 33m2 COLOR Grayã??Whiteã??ivoryã??Green DRY TIME Dries to touch in about 1-2days . Low temperatures or high humidity conditions will affect drying time. Full cure should be reached in 14-30 days. CLEAN UP 1. Clean hands and tools with soap water. 2. After 30 days or paint has fully cured, areas may be wasted using a non-abrasive, mild detergent and cellulose sponge. WARNING (Read the following carefully for your own safety) 1. Keep out of reach of children-Do not take internally. 2. May cause eye, skin and respiratory tract irritation. May be harmful if swallowed. Use only with adequate ventilation.
DESCRIPTION Power Screw adhesive is one of ITLS new range of power adhesives developed to give a cost effective and high adhesion performance. It is very low in odor and free of aromatic solvent for use indoor and outdoor. It was designed for use by both the home handy man and professionals. Power Screw adhesive which consists of tough elastomeric rubber, tackifying resins and Light hydrocarbon solvent. Power Screw can be used in most common construction materials. The substrates are timber, plywood, MDF, particle board, hard board, plaster board, cementitious fibrous board, concrete, ceramic, aluminum, ,mild steel, galvanized iron sheet, back of mirror (on wall only). FEATURES *Unique user friendly, highly pseudo-plastic and non runny characteristic making it TRULY easy to use on vertical wall and ceiling. * Extremely easy to extrude from cartridges in winter making it an all round product for use in all seasons. * Gap filling because of its higher solid content and especially it is highly pseudo-plasticity (soft smooth by stiff, non-sagging) property. * Flexible but tough for use around home and in construction * Easy on hand to extrude and apply due to its unique consistency. *Easy to spread our adhesive evenly and thinly due to its soft buttery consistency. * Broad application for most timber based, cementitious substrates, ceramic and most common metallic construction products. * Printable when dried. * Help to spread out pressure on bonded materials thereby prevent localized stress leading to adhesion failure.
DESCRIPTION ITSEAL is truly developed for sealing window frames with highly durable and flexible properties to withstand severe weathering and extreme temperatures. It seals small gap that normal sealant cannot reach and penetrate. It provides a truly watertight seal deep into minute joint and gap. FEATURES * ITSEAL is the only waterproof sealer that is completely watertight. * It is highly water repellent that no water can get through it during storm. * It adheres well on aluminum and glass * Once dried, ITSEAL is flexible and accommodate joint movement due to vibration. * Mill finish aluminum, oil or wet surfaces can also be well-sealed. VOC CONTENT Type of Regulated Adhesive under the Air Pollution Control (Volatile Organic Compounds) Regulation of Hong Kong: Architectural Sealant VOC Content (Ready to use): 248g/Ltr. SURFACE PREPARATION For maximum adhesion, the adhesive surface must be free of dust, release agent, oil and grease. Wipe surface with solvent is recommended. Solvent are obtainable from ITLS-SB. This information in this catalogue is provided to the best of our knowledge from results gathered both internal and external credited laboratories. However, we have no control over site applications, site conditions and workmanship of the applicator. We therefore will not accept any liability, either directly or indirectly arising from the misuse of these products or when the product is used not in accordance with any advice, specification, and recommendation of information given by us, The user is responsible for checking the suitability of these products for its intended use. APPLICATION ITSEAL can be used with hand operated or air operated grease pump. Other simple extruding device can also be used but it has to be solvent resistance. LIMITATION * Not suitable large gap wider than 5 mm wide and deep. For deeper joint fill to half of it, let it dry overnight and fill it up the next day. * Not suitable for use as expansion joint. COLOUR AND PACKING 26 kg / pail Grey/Black/Bronze/White SAFETY INFORMATION * ITSEAL is flammable. Please keep away from sources of ignition during application. * Avoid breathing in solvent by wearing solvent vapor respiratory mask in badly ventilated area or confined space. * Avoid contact with skin and eyes. If swallowed please contact doctor immediately. * ITSEAL meets the requirement of RoHS regulation of European Union and it does not contain eight heavy metals which were restricted by ASTM F963 or EN71 part3. * Please read the Material Safety Data Sheet in regards to flammability and health and hazard. SHIPPING/STORAGE INFORMATION ITSEAL must be stored in a cool place under 25°C and away from direct sunlight. The shelve life is 12 months if stored in accordance to the recommendation. Dangerous Goods Information: Cement Adhesive, Class 3, UN1133 PG III.
Meat And Bone Meal .
Mud crab.