DESCRIPTION CP-311T elastic polyester is a new type product with a special polymerization. It is a one compound high-performance elastic waterproof membrane. The single-liquid self-crosslinking waterproof polymer with anti-fouling and wear-resisting properties is used for the coating and protection of elastic waterproof materials, roofing, wall and other elastic materials. This product has high adhesion, elasticity, wear resistance and protection. It is water-resistant, weather-resistant and hydrophobic. It is the best choice for long-term protection. SPECIFICATIONS 1. AppearanceWhite Emulsion 2. Solid Content48~52 % 3. Viscosity3000 ~ 6000 cps(RVT#3@25) 4. Proportion1.15~1.25 PROPERTIES Developed with an environmentally friendly formulation that is water-based, non-toxic and low-odor, in line with environmentally friendly low VOC regulations and CNS waterproofing specifications. The self-crosslinking single-liquid resin can make the construction work simple, and can be directly sprayed, rolled or brushed. Suitable for indoor, outdoor, floor and wall applications with high toughness, water resistance and wear resistance Excellent film properties: elastic value and stretchability, and excellent wear resistance Weathering, aging resistance, can effectively increase the life of the paint Excellent adhesion, breathability and foam resistance, which can effectively prevent surface blistering and false after application.
DESCRIPTION CC-102 Concrete Hardener is a clear high performance waterborne liquid which being applied to the floor and absorbed into the concrete pores and reacts with the calcium salts effectively making the concrete surface denser and considerably less porous. APPLICATIONS Suitable for improving the quality of concrete floors in factories, warehouse and any other area where hard non-dusting floors are important. SURFACE PREPARATION Surfaces should not have had previous treatments. They should be firm and free from oil, dirt, dust etc. Weak spots should be cut out and filled with CEMCRETEâ??S FLOOR PATCHING. All surfaces to be dry at time of application. MIXING AND APPLICATION Shake or roll drum to thoroughly mix contents. Apply HARDENER to the dry surface using a soft household broom or paint roller. Application should be liberal but it is advisable to brush away unabsorbed pools immediately to avoid the HARDENER forming glassy layers. Allow one day between coats. Two coats are usually sufficient, but a third might be required if the concrete is very porous SPECIMEN FINISH A trial area should be treated on site for the Engineerâ??s or Architectâ??s approval. COVERAGE Depends upon the suction and texture of the surface. Approximately 6m2 / litre/coat.
DESCRIPTION Cement Filler is used for exterior coating on the tiles, steel plate, a smooth surface or a low porosity material to combine the old surface and the new one. FEATURE * Water-based formulations of two special adhesive. * For tiles, steel, a smooth surface or a low porosity of the material surface ?¯ etc. * With waterproofing, impervious, weather resistance, freeze-thaw characteristics. * Can be used both on wet and dry surfaces. * With good adhesion. APPLICATION * To adhere and mix old concrete surface and new concrete surface * Can be used to adhere indoor and outdoor old cement walls, fiber cement board, tile, concrete, colored steel board, asbestos and various green compartment plates etc. WORKING PROCEDURE 1 All surfaces need to be clean, free from dust, rust, white birch and either grease. In addition, the concrete could be moistened but not with floating. 2. Coating CA-003M by brush, roller or spray on the substrates. The coverage would be 4 ~ 7m ² per kilograms which depends on the situation of porous and roughness of the substrates. 3 All the tools can be cleaned by water.
Description 1. Tough film and good adhesion on the concrete, able to penetrate into concrete. 2. Good resistance to water , brine and chemicals. Excellent mechanical strength and physical properties. 3. Good resistance to impact and abrasion. 4. Easy application , drying fast. Prepare to use 1. Mix base and hardener by the mixing ratio and Stir thoroughly, then setting at least 15 minutes. Thinner may be used to reduce viscosity. 2. Remove all foreign particles, oils, grease , rust and moistures from the surface before application. 3. Two packs product, must be used completely during the duration of its pot life. 4. Donâ??t apply when the temperature is < 10â??,>40â??, relative humidity is >90â?? or the surface temperature of substrate is not higher than the dew point for at least 3â??. 5. If the coating interval is exceeded , the surface of base coat must be roughened to insure adhesion. 6. Keep away from heat, sparks and flame. 7. Stored with good ventilation. 8. Keep adequate ventilation during application. 9. The actual coverage may vary, depending on application technique, job conditions and type of surface. Under brushing & rolling application the actual coverage is estimated at 70% of the Theoretical coverage and 60% for spraying. **The parts of data base above could be affect by application condition at job site, please reference guide specification or contact with relative technical personnel. Color : Clear Drying time : Tack-free : 2 hours Hardness : 8 hours Full cure : 7 days (grease)
DESCRIPTION CP-502 is Ethylene-Vinyl Acetate copolymer latex , it has film with flexibility. It can be use to mix cement , extend prolife and reduce stiffness of cement. APPLICATION CP-502can be use to mix cement , extend prolife and reduce stiffness of cement, and it has flexibility and waterproofing after cement solidification. It is a elastomeric coating used to the surface of a cement wall, the latex can add to more filler and change the viscosity unapparent. THICKNESSï¼?About 1 mm when just sizing; about 0.8 mm after dry COVERAGEï¼?About 2 Kg/m2 ï¼?Dry membrane reach to 2 mmï¼?apply 2~3 timesï¼? SUGGESTIONï¼? 1. Tools: Brush/ Roller/ Spray Gun 2. Normal: EmulsionAAggregateB11By Weight 3. Enhance elongation performance by increasing emulsion content 5~10%. 4. To get better tensile strength might reduce the usage of emulsion. 5. Dilute with water if apply by roller or spray gun. Add 10 6. Avoid cracking, shrinking or other paint failure by following PRIMERï¼?CA-002 or CA-003 dilute 2~3 times for using COATINGï¼?Water-base Paint. Test before using, if apply solvent-base paint. DILUTE AGENTï¼?Waterï¼?5ï½?10% for rollerï¼? PRECAUTION CP-502 should be stored below 40â??,and be kept away from sunlight or fire. Shelf life is one year.
