Automatic kebab skewer machine Model : AS400H a production of AL SAED COMPANY company is an innovation for preparing roast meat. Specification and advantage of kebab skewer machine: - Skewer meat without manual task increases customer's trust and satisfaction by following healthy principles. - Device has designed for every simple user. - Applicable in different dimension and weights. - Steady roasting meat as a result of better cook. - Applicable in tow manual and automatic. - It is equipped with automatic counter and emergency switch - Machine cover and parts related to the meat is made of stainless steel. Technical specification of Kebab Skewer Machine Model: AS400H - Motor power: single phase â?? 1.1 kw - Cover: stainless steel - Equipped with modular pressure breaker and automatic counters and emergency stop buttons - Applicable in fitting meat weight - Dimensions: length 75 cm, width 50 cm, height 60 cm - Weight: 120 kg - Number of spiting: 1000 spit in hour - Mold (dimension and roast meat weight) is registered - Capacity of Hydraulic oil: 20 liters
Automatic kebab skewer machine Model : AS400H a production of AL SAED COMPANY company is an innovation for preparing roast meat. Specification and advantage of kebab skewer machine: - Skewer meat without manual task increases customer's trust and satisfaction by following healthy principles. - Device has designed for every simple user. - Applicable in different dimension and weights. - Steady roasting meat as a result of better cook. - Applicable in tow manual and automatic. - It is equipped with automatic counter and emergency switch - Machine cover and parts related to the meat is made of stainless steel. Technical specification of Kebab Skewer Machine Model: AS400H - Motor power: single phase â?? 1.1 kw - Cover: stainless steel - Equipped with modular pressure breaker and automatic counters and emergency stop buttons - Applicable in fitting meat weight - Dimensions: length 75 cm, width 50 cm, height 60 cm - Weight: 120 kg - Number of spiting: 1000 spit in hour - Mold (dimension and roast meat weight) is registered - Capacity of Hydraulic oil: 20 liters
In all TI UNIT air handling units the frames are from aluminum profiles while the chassis and body panels are made from galvanized steel sheets in appropriate thicknesses. All units are completely painted in the proper thickness. Blower(S): Double width-double inlet centrifugal fans with forward curved blades are normally used for low pressure drop requirements as opposed to fans with backward curved blades which are for high pressure drop applications. Fans and housings are made of galvanized steel each set off a plus other related components such as shafts are statically and dynamically balanced, shafts are selected from proper material and size. Other power transmission components such as pulleys and belts are also suit ably chosen depending on the required fan speed and electric motor power. Fan(s) and the corresponding electric motor(s) are installed on an independent chassis which is itself installed on the main chassis using vibration dampers in order to eliminate transfer of vibrations to the structure. To further reduce the effects of vibrations, fan outlet (s) are also connected to the structure via flexible material such as canvous. All 380V/3/50Hz electric motors are selected with insulation class of (f) and ingress protection of (IP- 54). Electric motors with ingress protection of (IP- 55) are also available upon request. Coil (S): Cooling and heating coils or either one of the two depending on the Requirement May be installed. Cooling coils are available in two, types of chilled water and direct expansion (D.X.) as per clients requirements. The chilled water coils are constructed of 5/8 O.D copper tubes plate finned (8, 10, 12 or 14 FPI) in aluminum or copper upon request. The D.X. Coils are constructed of 3/8 OD copper tubes also plate finned (10, 12 or 14 FPI) in aluminum or copper as required. The chilled water for cooling coils in to be supplied by a water chiller and in the D.X. coils cooling is provided through the use of refrigerant such as R-22, R-407c or R-134a. Chilled water coils may be requested in 4 or 6 rows and as to the D.X. coils, they are available in 4 or 6 row configurations. Heating coils are available in two types of hot water and steam. The hot water coil similar to chilled water coil is offered in 1 or 2 row configurations. Steam heating coils are constructed of 1/2 seamless steel pipe spiral finned in aluminum or copper. Coils in 1 & 2 -row configurations are available upon request. Mixing box: Fresh and return air streams are mixed in the mixing box .An independent air damper is included for each air stream. Air Dampers are manufactured from aluminum in opposed blade configuration and are air sealed through the use of rubber strip gasket. Damper actuators ma y be easily installed when required. Washable aluminum filter modules 2 inches in thickness are arranged in (V) type configuration inside these boxes. Housing for
TI UNIT compact roof top chiller units are manufactured in type of air cooled in capacities of 5 to 360T.R. in one to four circuited configurations. In all TI UNIT compact roof-top chiller units the frames and body are from galvanized steel & stainless steel (316l) (option) the chassis made steel channel in appropriate thicknesses and all of units are completely painted in the proper thickness. Evaporators are high efficiency shell and tube heat exchangers, designed based on TEMA. Condenser of compact rooftop chiller unit made of plated coil, designed based on TEMA. Chillers with plate type heat exchangers are available upon request. TI UNIT compact roof top chillers can be designed to operate with R-22, R-407C and R-134a refrigerants. Safety controls installed on all units include high, oil and low pressure cut-outs, compressor safety cut-out, water anti freeze thermostat, water flow switch and evaporator entering water thermostat and compressor operation time logger. The above mentioned are all chosen from the most recognized controls manufactures in the air conditioning industry. Automatic condensing temperature control: A controller, factory installed on each unit automatically stages the condenser fans allowing the unit to start. With this controller the condenser fans start stage by stage. Raw materials such as copper tubes, fittings and valves are supplied by well-respected manufacturers. Electrical safety measures such as three phase controller and circuit breakers are, available on all units. A fault detection system for the whole unit is available upon request. Microprocessor based PLC controller is also available as needed. Suitable accessories make the chillers operable in all seasons according to the application requirements without any problems.
TI UNIT screw chillers are manufactured in two types of air cooled and water cooled in capacities from 50 to 560 T.R. in one to four circuited configurations. Evaporators and condenser Chillers with plate type heat exchangers are available upon request. For further related technical information, please send your inquiries to TI UNIT mfg. group. TI UNIT screw chillers can be designed to operate with R-22 and R-134a refrigerants. Bitzer screw compressors suitable for use with R-134a refrigerant are available in two versions (m.vr.1 & m.vr.2) which can be used in the chillers as required. Safety controls installed on all units include high and low pressure cut-outs, compressor oil level control safety cut-out, water anti freeze thermostat, water flow switch and evaporator entering water thermostat and compressor operation time logger. The above mentioned are all chosen from the most recognized controls manufactures in the air conditioning industry. Compressors are by Bitzer which happens to be one of the best and most reliable brands. Raw materials such as copper tubes, fittings and valves are supplied by well-respected manufactures. Electrical safety measures such as three phase controller and circuit breakers, are available on all units. A fault detection system for the whole unit is available upon request. Microprocessor based PLC controller is also available as needed. TI UNIT screw chillers are also available upon request for industrial applications in both Air Cooled and Water Cooled types; Suitable accessories make the chillers operable in all seasons according to the application requirements without any problems.
Specifications of Rice baking pot Capacity of 25 kg Iranian rice and 35 kg foreign rice 2.5 mm thick welded baking compartment, polished by 316 AISI Stainless Steel with a polishing surface of at least 0.6 micron Includes pressing floor for reinforcement and ease of discharging of contents (Request for baking tank to be ordered on inquiry) Equipped with European Thermocouple Spark and burner. Includes Stainless steel 304 AISI door, tray and chassis Direct flame by Tubby Stainless Steel 430 AISI burner with low working pressure and European high thermal power. Double-walled door with air insulation, high quality pure silicone Rubber sealing (German Food Grade). Equipped with 4 door clamps 50mm thick ceramic insulation and density 128 with refractory fabric coating to reduce heat dissipation Stainless steel hinges with capability of holding doors in different modes. Equipped with a safety and resistant valve against acids and gases from combustion, include combustion chamber and stainless steel AISI 309 exhaust (fireproof grade) 2 mm thick and formed to enhance maximum combustion chamber Equipped with 2.5-inch AISI 304 Stainless Steel petcock Includes AISI 304 stainless steel frame and chassis Equipped with a pressed strainer for baking rice. There is no need to remove the strainer for rice rinse Includes filter and governor on main gas inlet View of cubic boilers with insulated and reinforced polyurethane foam Capability of using CNG or liquefied LPG Equipped with 4 adjustable legs
Nigerian National Petroleum Corporation (NNPC) for Bonny Light Crude Oil Specification (Nigerian BLCO) Nigerian NNPC Specifications for BLCO: Specific Gravity: 0.8459. Water Content: 0.2% Vol. Max BSW: 0.6% Vol., max. Pour point: Below 40 Degree F. max Salt: LB per 1,000 bbl, 12, max Total Sulphur, wtK%: 0.14 max Reid Vapor Pressure: 6.52 PSIG, max Carbon Residue, wt%: 1.0, max. VINI, PPM wt: 2.0 Vis, cst @ 37.8 Deg C.: 3.47, min. Yield C1-C4 wt%: 2.10 PROCEDURE FOR TAKE OVER (TTO) GHANA WATERS. Discount: $11/$4 1) Seller issues Contract. 2) Buyer and Seller sign / seal this contract Agreement and buyer return with Copy of ATB / NOR Format which includes buyers name, inspection company name, shipping agent details, super cargo name and ID, all emails included, harbor master name, phone number, tug boat name, radio channel, color and flag. 3) Upon confirmation of Buyer's high court indemnity and international passport seller instruct loaded vessel to issue NOR/ETA after Sellerâ??s BG is been confirmed by the NNPc terminal to Buyer's harbor master, and sail to 10/12 nautical mile Tema Ghana. 4) Upon arrival at 10/12 nautical mile Tema Ghana, vessel captain makes announcement to Port authority in favor of Buyer and issue Matb to board Buyer's super cargo and inspection team. 5) Within 24 hours, Buyer's shipping agent processes clearance and board inspection team on loaded vessel at Buyer's expenses. Inspector disembarks from loaded cargo with samples for Q &Q, while supercargo remains on board until final tanker take over. On completion of boarding, attestation and collection of samples for Q&Q by inspector, Buyer releases USD 1,000,000 for logistics and documentations. 6) Final Payment is made by Swift Wire Transfer via Swift MT103 (less USD1, 000,000) within 72hrs through Sellerâ??s commercial invoice presented after Q & Q is ascertained by buyerâ??s inspection agents and presentation of the original shipping documents to the buyer. 7) Seller introduces Buyer to vessel owner for re-chartering to enable Buyer re-chatter vessel to enable vessel sail to Buyerâ??s pod. These are the specs and the procedure plus the price $11/4. No instrument or bank Guarantee required only pay $1M USD for Logistics after inspection DIP and pay and we (RAINBIRD MODRAN PROJACTS) will charge a $2 with each Barrel for our Office commission from Buyer side. If are interested and agreed with above terms please let me Know, we have a good supply source in line, so we will do a good business within short notice, if you still need any more clarification, please don't hesitate to contact us. We are herewith assisting you all times.
Each union is thoroughly inspected to ensure long, dependable service in the most extreme conditions. Available in stock at our distribution center in houston. Three lug nuts and self-locking acme threads provide quick make-up and break-out Color coded for quick identification Unique identification for sour gas unions Meet or exceed national association of corrosion engineers standard nace mr-01-75 and api rp-14e Manufactured from quality steel meeting astm and/or aisi standards All unions provide pressure-tight & positive sealing for low-pressure services (500 to 2, 000 psi) The spherical surface male sub and angular surface female sub form a metal-to-metal seal, the ball and tangent provides a perfect seal Range from 1/2 to 12 with cold working pressures from 500 to 20, 000 psi Fully interchangeable with most major brands of hammer unions
