Base Oil SN 350 is a medium stock base oil produced from the vacuum distillates and residual components using the traditional refining methods. It has viscosity 8-9,5 cSt at 100C and 67-70 cSt at 40C. SN 350 is used in lubricant and lubricant additives production, mainly for industrial applications. The main benefits of SN 350 base oils are low sulphur content, high viscosity index, high oxidation stability and good susceptibility to the additives.
VG-20 bitumen is a grade of viscosity bitumen used in cold climatic and high altitude regions. This grade of bitumen is suitable for road construction in regions with 30 to 37 C average temperature. In North India, vg20 is used for road construction in hot mix asphalt. The standard penetration value of bitumen viscosity grade VG-20 is 60 mm at 25 C. The absolute viscosity of VG-20 bitumen is 1600 to 2400 poise at 60 C.
VG40 bitumen is used in areas in which high pressure comes from heavy traffic loads, such as intersections, near tolls booths, and truck parking lots. Due to the high viscosity of this bitumen, it is more appropriate for improving resistance to shoving and other problems associated with higher temperatures and heavy traffic loads. Itâ??s long time that industries use vg-40 instead of the penetration grade bitumen 40/50.
Urea is a raw material forthe manufacture of twomain classes of materials:urea-formaldehyde resins and urea-melamine-formaldehyde used in marineplywood. AGRICULTURE More than 9O% of world industrial production of urea is destined for useas a nitrogen-release fertilizer. Urea has the highest nitrogen con-tent of all solid nitrogenous fertilizersin common use. Therefore, it has the lowest transpor-tation costs per unit of nitrogen nutri-ent.
Bitumen Penetration Grade 85/100 is a standard penetration grade Bitumen usually used as a Paving Grade Bitumen suitable for road construction and for the production of asphalt pavements with superior properties. This grade of Bitumen is mainly used in the manufacture of hot mix asphalt for bases and wearing courses. Penetration Grade Bitumen supplied by RABIT (RAHA BITUMEN) Co. is petroleum grade bitumen, manufactured from fractional / vacuum distillation of crude oil. The Bitumen supplied by RABIT Trading Co. This bitumen is produced through aeration on vacuum bottom (the raw material used for making bitumen left in vacuum distillation column in oil refineries) in bitumen production units. Its penetration grade ( the measure of bitumen hardness) is between 85 to 100. Penetration Grade bitumens are specified by the penetration and softening point test. The designation is by penetration range only. The penetration grade bitumens have a thermoplastic property which causes the material to soften at high temperatures and to harden at lower temperatures. This unique temperature/ viscosity relationship is important when determining the performance parameters such as the adhesion, rheology, durability and application temperatures of bitumen. The Bitumen mode is dependent on temperature. The temperature-vs-stiffness relationship of bitumen is dependent on the type of crude oil and its refining method. Bitumen penetration grade 85/100 is semi hard penetration grade bitumen used as a paving grade bitumen which is suitable for road construction and repair. It is also used for the production of asphalt pavements with the below technical specification. This grade of bitumen is mainly used in the manufacturing of hot mix asphalt for bases and wearing courses. Bitumen 85/100 is one of the most used bitumen grades and it�¢??s a basic material for all other bituminous products. Penetration determines the hardness of bitumen by measuring the depth to which a standard loaded the needle will vertically penetrate in 5 seconds, in a sample of bitumen maintained at a temperature of 25 degrees Celsius.
VG10 bitumen is the softest grade of viscosity bitumen. This type of bitumen is widely used for spraying applications and surface coating. VG 10 bitumen means that your bitumen is also suitable for paving roads in a very cold climate instead of the old 80/100 penetration grade. The air temperature that matches VG10 bitumen ranges from -10 â?¦C to 25 â?¦C. Due to the high temperatures in hot climatic zones, the application of VG10 cannot provide desirable rutting resistance. This type of bitumen is also used to manufacture bitumen emulsions and modified bitumen products especially in India. As a viscosity grade bitumen, VG10 has a better performance incold weather. To know vg10 latest price contact us.
Bitumen penetration grade 60/70 is semi-hard penetration grade bitumen using as paving grade bitumen suitable for road construction and repair conjointly for the production of asphalt pavements with below technical specifications. This grade of bitumen is mainly used in the manufacture of hot combine asphalt for bases and wearing courses. Bitumen 60/70 is the most used bitumen grade and basic material for all alternative bituminous products. Bitumen Penetration Grade 60/70 is mainly used in the manufacture of hot mix asphalt for bases and wearing courses. Penetration Grade Bitumen supplied by RAHA GROUP is petroleum grade bitumen, manufactured from fractional / vacuum distillation of crude oil. The Bitumen supplied by RAHA GROUP is produced from vacuum residue (short residue) feedstock. RAHA Penetration Grade bitumens are specified by the penetration and softening point test. The designation is by penetration range only. The penetration grade bitumens have a thermoplastic property which causes the material to soften at high temperatures and to harden at lower temperatures. This unique temperature/ viscosity relationship is important when determining the performance parameters such as the adhesion, rheology, durability and application temperatures of bitumen.
A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom. Billets are further processed via profile rolling and drawing. Final products include bar stock and wire. Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.
A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom. Billets are further processed via profile rolling and drawing. Final products include bar stock and wire. Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.
A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom.[1][2][4] Billets are further processed via profile rolling and drawing. Final products include bar stock and wire.[3] Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.
Iron ores are the raw material used to make iron and steel. Iron ore production has significantly expanded in recent years, owing to increasing steel demands in developing countries, such as China. As the content of iron ore in deposits has deteriorated, low-grade iron ore has been processed. Iron ore concentrate is an output product from processed iron ores that have been milled (crush, grind, magnetic separation, flotation) to separate deleterious elements and produce a high-quality product. Sintering and pelletizing are economic and widely used agglomeration processes to prepare iron ore fines/iron concentrate for ironmaking use. The quality requirements of sinter and pellet, such as physical, chemical, and metallurgical specifications, depend on each ironmaking furnace, and those requirements influence the operation of the iron ore sintering and pelletizing plant. Researchers have usually focused on the effect of the chemical, physical, and mineralogical characteristics of iron ore on these steps and the consequences for sinter/pellet quality and sintering/pelletizing performance. The present Special Issue on â??Iron Concentrate Particlesâ?? will summarize the progress achieved in the last five years.
Bitumen penetration grade 40/50 bitumen means the penetration value is in the range 40 to 50 at standard test conditions which commonly used as a Paving Grade. Bitumen is applicable for the production of hot mix asphalt for bases and pavements and for road construction. Penetration Grade Bitumen supplied by RABIT (RAHA BITUMEN) Co. This bitumen is produced through aeration on vacuum bottom (the raw material used for making bitumen left in vacuum distillation column in oil refineries) in bitumen production units. Its penetration grade ( the measure of bitumen hardness) is between 40 to 50. Bitumen is specified by the penetration and softening point test. Designing is by penetration range only. The penetration grade bitumen has a thermoplastic property which causes the material to soften at high temperatures and to harden at lower temperatures. This unique temperature-viscosity relationship is important when determining the performance parameters such as the adhesion, rheology, durability and application temperatures of bitumen.
Base Oil SN 500 is defined as a light grade base oil at the upper end of the specifications for Grade I base oils. It is mostly used in lubricant production. It is a Group I base oil which has undergone solvent refining processes. To finish the refining it was hydrogen treated to clear out any impurities. Applications : Base Oil SN 500 works as a base stock for several industrial lubricants Engine oils Transmission fluids Gear oils Metal working fluids Greases Hydraulic oils Transformer oils
Prilled urea is a form of nitrogen-rich solid fertilizer that has the ability to dissolve quickly in water. Prilled urea is more commonly used today to resist breaking down when mixing with other fertilizer components like Potassium chloride. It is also known as ice melting or deicing urea since it can reduce ice efficiently, even at very low temperatures ( -6 â?¦C) .
Storage Type: COOL PLACE Specification: Moisture 5% Type: Cashew Nut Shelf Life: ONE YEAR Manufacturer: OWN PRODUCTION Ingredients: Fine Content: GOOD QUALITY Cultivation Type: Organic Processing Type: Roasted Style: Dried Packaging: Cotton Boxes Grade: WW320, WW450, WW210, WW240, WW180 Use: Ready to eat Place of Origin: Tanzania Grade Ww320
Urea 46%, also known as urea fertilizer, is a commonly used nitrogen fertilizer and animal feed additive in the agricultural industry. This white crystalline solid is highly soluble in water, making it easy to apply to crops. Urea 46% provides plants with an essential source of nitrogen, which is crucial for their growth and development. However, like any agricultural input, urea 46% has its pros and cons. In this blog, we will explore the composition, production process, and practical applications of urea 46%, as well as its potential drawbacks and best practices for farmers. By understanding the benefits and limitations of urea 46%, farmers can maximize its potential and optimize crop production while minimizing environmental impact.
Our iron ore pellets and fines are made from magnetite and have high iron ore content â?? pellets at around 67 percent concentration and fines over 70 percent. This means they have lower impact on the environment than competing pellets and products such as sintered hematite fines. Using pellets instead of sinter (slightly larger pieces of iron ore) in customersâ?? pig iron processes saves emissions at steel plants. The high concentration of iron combined with the carefully tested and balanced additives in our pellets also result in lower emissions in customersâ?? ironmaking processes.
HMS Scrap /Heavy Melting Scrap (HMS1 / HMS2) /HMS1 HMS 1&2 Shredded HMS Bundle Steel Scrap Backed by huge industry knowledge, we are presenting a supreme quality range of HMS Scrap (1 & 2) to our highly valued consumers. These range of HMS Scrap are highly acclaimed for its high durability, tensile strength and exhibits superior resistant to adverse conditions. We test each and every product before release by various industrial parameters by our quality analyst. Client purchase these at reasonable rate. HMS 1/2 SCRAP / METAL SCRAP / HEAVY STEEL SCRAP / /Heavy Melting Steel Scrap Metals for sale. We can supply you HMS scraps, HMS 1, HMS 1/2, Used rails scraps. Chemical Composition: C:0.06 - 0.082% Mn:0.75 - 1.05% SI:0.13 - 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15% We have Used Rails | HMS 1:2 ISRI CODE R50-R65 Composition C - 0.54-0.82%, SI - 0.18-0.40%, MN - 0.60-1.05%, S - 0.04% maximum P - 0.035% maximum AS: - 0.01% Maximum of Mass Share HMS is usually traded as a blend of 1 & 2, either a premium blend (80:20) or lower grade mixes (70:30) and (60:40). C:0.06 - 0.082% Mn:0.75 - 1.05% SI:0.13 - 0.28% P: Max 0.035% S: Max 0.045% Ar: Max 0.15% Used clean rail, without slag, dross, trash, wood, plastic, oily parts, grease, alloy, prohibited goods, whole sets of machine and usable parts for machines, cast iron, motor turning blocks, engine blocks, war and explosive for armour plated materials, mud or wastes and maximum harmless impurities is less than 0.1%;
Aluminum Extrusion 6063 Scrap Aluminum Extrusion 6063 Scrap. It is the most common alloy used for aluminum extrusions. Normally, Aluminium Extrusion 6063 Scrap shall consist of clean aluminum profile extrusions including window, shop fittings, irrigation tubes and door frames. However, it must be free of screws, iron components, plastics, rubber or other foreign materials. Chemical composition Silicon minimum 0.2%, maximum 0.6% by weight Iron no minimum, maximum 0.35% Copper no minimum, maximum 0.10% Manganese no minimum, maximum 0.10% Magnesium minimum 0.45%, maximum 0.95% Chromium no minimum, maximum 0.10% Zinc no minimum, maximum 0.10% Titanium no minimum, maximum 0.10% Other elements no more than 0.05% each, 0.15% total Aluminium ; Remainder
African butters and oils (shea butter, cocoa butter, red palm oil,coconut oil) honey, honey comb, bee wax, beef offals (beef omasum ,bile paste,ox pizzle) camel skin, cow skin, donkey skin, scrap, railway scrap, copper scrap, used battery scrap, pte bottle scrap ,occ paper..
