Kenyan Cold Pressed Castor Oil Suppliers and Manufacturers

VG10 bitumen is the softest grade of viscosity bitumen. This type of bitumen is widely used for spraying applications and surface coating. VG 10 bitumen means that your bitumen is also suitable for paving roads in a very cold climate instead of the old 80/100 penetration grade. The air temperature that matches VG10 bitumen ranges from -10 â?¦C to 25 â?¦C. Due to the high temperatures in hot climatic zones, the application of VG10 cannot provide desirable rutting resistance. This type of bitumen is also used to manufacture bitumen emulsions and modified bitumen products especially in India. As a viscosity grade bitumen, VG10 has a better performance incold weather. To know vg10 latest price contact us.

VG-20 bitumen is a grade of viscosity bitumen used in cold climatic and high altitude regions. This grade of bitumen is suitable for road construction in regions with 30 to 37 C average temperature. In North India, vg20 is used for road construction in hot mix asphalt. The standard penetration value of bitumen viscosity grade VG-20 is 60 mm at 25 C. The absolute viscosity of VG-20 bitumen is 1600 to 2400 poise at 60 C.

Bitumen Penetration Grade 85/100 is a standard penetration grade Bitumen usually used as a Paving Grade Bitumen suitable for road construction and for the production of asphalt pavements with superior properties. This grade of Bitumen is mainly used in the manufacture of hot mix asphalt for bases and wearing courses. Penetration Grade Bitumen supplied by RABIT (RAHA BITUMEN) Co. is petroleum grade bitumen, manufactured from fractional / vacuum distillation of crude oil. The Bitumen supplied by RABIT Trading Co. This bitumen is produced through aeration on vacuum bottom (the raw material used for making bitumen left in vacuum distillation column in oil refineries) in bitumen production units. Its penetration grade ( the measure of bitumen hardness) is between 85 to 100. Penetration Grade bitumens are specified by the penetration and softening point test. The designation is by penetration range only. The penetration grade bitumens have a thermoplastic property which causes the material to soften at high temperatures and to harden at lower temperatures. This unique temperature/ viscosity relationship is important when determining the performance parameters such as the adhesion, rheology, durability and application temperatures of bitumen. The Bitumen mode is dependent on temperature. The temperature-vs-stiffness relationship of bitumen is dependent on the type of crude oil and its refining method. Bitumen penetration grade 85/100 is semi hard penetration grade bitumen used as a paving grade bitumen which is suitable for road construction and repair. It is also used for the production of asphalt pavements with the below technical specification. This grade of bitumen is mainly used in the manufacturing of hot mix asphalt for bases and wearing courses. Bitumen 85/100 is one of the most used bitumen grades and it�¢??s a basic material for all other bituminous products. Penetration determines the hardness of bitumen by measuring the depth to which a standard loaded the needle will vertically penetrate in 5 seconds, in a sample of bitumen maintained at a temperature of 25 degrees Celsius.

Bitumen penetration grade 60/70 is semi-hard penetration grade bitumen using as paving grade bitumen suitable for road construction and repair conjointly for the production of asphalt pavements with below technical specifications. This grade of bitumen is mainly used in the manufacture of hot combine asphalt for bases and wearing courses. Bitumen 60/70 is the most used bitumen grade and basic material for all alternative bituminous products. Bitumen Penetration Grade 60/70 is mainly used in the manufacture of hot mix asphalt for bases and wearing courses. Penetration Grade Bitumen supplied by RAHA GROUP is petroleum grade bitumen, manufactured from fractional / vacuum distillation of crude oil. The Bitumen supplied by RAHA GROUP is produced from vacuum residue (short residue) feedstock. RAHA Penetration Grade bitumens are specified by the penetration and softening point test. The designation is by penetration range only. The penetration grade bitumens have a thermoplastic property which causes the material to soften at high temperatures and to harden at lower temperatures. This unique temperature/ viscosity relationship is important when determining the performance parameters such as the adhesion, rheology, durability and application temperatures of bitumen.

Bitumen penetration grade 40/50 bitumen means the penetration value is in the range 40 to 50 at standard test conditions which commonly used as a Paving Grade. Bitumen is applicable for the production of hot mix asphalt for bases and pavements and for road construction. Penetration Grade Bitumen supplied by RABIT (RAHA BITUMEN) Co. This bitumen is produced through aeration on vacuum bottom (the raw material used for making bitumen left in vacuum distillation column in oil refineries) in bitumen production units. Its penetration grade ( the measure of bitumen hardness) is between 40 to 50. Bitumen is specified by the penetration and softening point test. Designing is by penetration range only. The penetration grade bitumen has a thermoplastic property which causes the material to soften at high temperatures and to harden at lower temperatures. This unique temperature-viscosity relationship is important when determining the performance parameters such as the adhesion, rheology, durability and application temperatures of bitumen.

VG40 bitumen is used in areas in which high pressure comes from heavy traffic loads, such as intersections, near tolls booths, and truck parking lots. Due to the high viscosity of this bitumen, it is more appropriate for improving resistance to shoving and other problems associated with higher temperatures and heavy traffic loads. Itâ??s long time that industries use vg-40 instead of the penetration grade bitumen 40/50.

This bitumen is primarily used for the construction of extra-heavy bitumen pavements that have to bear significant traffic loads. Bitumen VG30 is the most widely used type of bitumen in road construction, insulation, building construction industries, and also in the production of cutback bitumen. Itâ??s better to know that this vg30 bitumen can be used instead of 60/70 penetration bitumen grade.

Urea 46%, also known as urea fertilizer, is a commonly used nitrogen fertilizer and animal feed additive in the agricultural industry. This white crystalline solid is highly soluble in water, making it easy to apply to crops. Urea 46% provides plants with an essential source of nitrogen, which is crucial for their growth and development. However, like any agricultural input, urea 46% has its pros and cons. In this blog, we will explore the composition, production process, and practical applications of urea 46%, as well as its potential drawbacks and best practices for farmers. By understanding the benefits and limitations of urea 46%, farmers can maximize its potential and optimize crop production while minimizing environmental impact.

Iron ores are the raw material used to make iron and steel. Iron ore production has significantly expanded in recent years, owing to increasing steel demands in developing countries, such as China. As the content of iron ore in deposits has deteriorated, low-grade iron ore has been processed. Iron ore concentrate is an output product from processed iron ores that have been milled (crush, grind, magnetic separation, flotation) to separate deleterious elements and produce a high-quality product. Sintering and pelletizing are economic and widely used agglomeration processes to prepare iron ore fines/iron concentrate for ironmaking use. The quality requirements of sinter and pellet, such as physical, chemical, and metallurgical specifications, depend on each ironmaking furnace, and those requirements influence the operation of the iron ore sintering and pelletizing plant. Researchers have usually focused on the effect of the chemical, physical, and mineralogical characteristics of iron ore on these steps and the consequences for sinter/pellet quality and sintering/pelletizing performance. The present Special Issue on â??Iron Concentrate Particlesâ?? will summarize the progress achieved in the last five years.

Pure sulfuric acid does not occur naturally due to its strong affinity to water vapor; it is hygroscopic and readily absorbs water vapor from the air.[6] Concentrated sulfuric acid is highly corrosive towards other materials, from rocks to metals, since it is an oxidant with powerful dehydrating properties. Phosphorus pentoxide is a notable exception in that it is not dehydrated by sulfuric acid but, to the contrary, dehydrates sulfuric acid to sulfur trioxide. Upon addition of sulfuric acid to water, a considerable amount of heat is released; thus, the reverse procedure of adding water to the acid should not be performed since the heat released may boil the solution, spraying droplets of hot acid during the process. Upon contact with body tissue, sulfuric acid can cause severe acidic chemical burns and even secondary thermal burns due to dehydration.[7][8] Dilute sulfuric acid is substantially less hazardous without the oxidative and dehydrating properties; however, it should still be handled with care for its acidity.

Our iron ore pellets and fines are made from magnetite and have high iron ore content â?? pellets at around 67 percent concentration and fines over 70 percent. This means they have lower impact on the environment than competing pellets and products such as sintered hematite fines. Using pellets instead of sinter (slightly larger pieces of iron ore) in customersâ?? pig iron processes saves emissions at steel plants. The high concentration of iron combined with the carefully tested and balanced additives in our pellets also result in lower emissions in customersâ?? ironmaking processes.

Prilled urea is a form of nitrogen-rich solid fertilizer that has the ability to dissolve quickly in water. Prilled urea is more commonly used today to resist breaking down when mixing with other fertilizer components like Potassium chloride. It is also known as ice melting or deicing urea since it can reduce ice efficiently, even at very low temperatures ( -6 â?¦C) .

A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom. Billets are further processed via profile rolling and drawing. Final products include bar stock and wire. Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.

A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom. Billets are further processed via profile rolling and drawing. Final products include bar stock and wire. Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.

A billet is a length of metal that has a round or square cross-section, with an area less than 36 in2 (230 cm2). Billets are created directly via continuous casting or extrusion or indirectly via hot rolling an ingot or bloom.[1][2][4] Billets are further processed via profile rolling and drawing. Final products include bar stock and wire.[3] Centrifugal casting is also used to produce short circular tubes as billets, usually to achieve a precise metallurgical structure. They are commonly used as cylinder sleeves where the inner and outer diameters are ground and machined to length. Because their size is not modified significantly, they are not always classified as semi-finished casting products.

We are able to supply quality dates without any problem irregardless. We can readily supply you with very good quality and quantity with specifications below and also to inform you that right now is a new season . Types Of Dates - Ajwa Khajoor - Medjoul dates - Amber Dates - Kholas Dates - Sagal Dates - Mabroom Dates - Khudri Dates - Sukkari Dates - Rashodia Dates - Safawt Dates Grade.: 1st Choice and 2nd Choice 100% Organic â?? Certified No use of pesticides or chemicals Hand-picked for quality assurance Do not contain any fat, cholesterol, or sodium Rich in potassium Packaging size can be customized according to your requirement from 250g to 20KG. SPECIFICATIONS OF DATES:- - Size : Big Size - Impurity: None - Cultivation Type : Organic - Processing Type : Dried - Admixture: None - Total defects: 0.01% ---------------------------------------------------- Country of origin: Pakistan/Iran/United Arab Emirates/Israel/Jordan Ingredients: 100% Organic pitted dates. Nutrition Typical Values per 100g: Energy (kJ): 1115kJ - 1290kJ Energy (kcal): 270kcal - 305kcal Fat: 0.2g Of which saturates: 0.1g Carbohydrates: 68g Of which sugars: 68g Fibre: 7.1g - 11g Protein: 3.3g Sodium: 0.001g --------------- By use of most advanced agricultural methods and equipment, we guarantee fresh and high quality dates. Quality standards is our first and foremost priority thatâ??s why we source all stock from organic farms and finest quality crops each year. To meet our clientâ??s requirements, we choose the best harvest, wash, dry and clean the dates before packing so you can get a satisfactory product. To preserve quality, we store in a dry and cool area away from direct sunlight. Timely Export.; We value product and production quality, as well as other services, and we value your time by providing a quick shipping of premium dates in bulk. PACKAGING Packaging size is customized according to your requirement from 250g to 20KG and we also provide private labelling for personal branding. Please specify your requirements, and we will be delighted to assist you. Health Benefits Aids digestion. Promoting regularity. Helps control blood sugar levels. Reduces inflammation. Boosts energy levels. Fights depression and anxiety. Reduces the risk of stroke and other cardiovascular diseases. Contains calcium, magnesium, and zinc all of which help to strengthen the immune system. Prevents anemia as well as dementia and other chronic illnesses. It provides increased energy and strengthens the nervous system.

We are a group of companies and one of the prominent traders and suppliers of varied collection of commodities. We have constantly evolved to create a richly diversified line of products from some of the most reputed fields across Africa. Our products are procured from authorized vendors and are in total compliance with set industry norms. On behalf of the Management of Alpha Metal & Chemical Solutions hereby termed as the seller and with full corporate authority and responsibility certifies, represents and warrants to inform you that we are ready, willing and able to supply under the penalty of perjury, the following commodity with its specifications mentioned below. Product Name : Rail Scrap (R50, R65 & HMS) Material : Iron Metal Scrap Application : Melting/Industrial Use Quantity : Agreed shipment/Bulky 50,000 Metric Tonnes Current location : Kenya Country of Origin: Colonial Price :$195 Per Tonne (Negotiable) Contract : CIF Loading Port : Mombasa Delivery : Immediately contract signed by both parties Port Destination : TBA Payment : By TT within 48 hours after delivery and final analysis at the final destination port CHEMICAL COMPOSITION: SCRAP/RAILROAD FERROUS SCRAP (R50/R65) R50 GOST 7173-75 : Weight 51.67 KG/Meter R65 GOST 8165-75 : Weight 64.72 KG/Meter C : 0.60 -0.82% Mn : 0.75 1.05% Si : 0.13 0.28% P : Max 0.035% S : Max 0.045% Ar : Max 0.051% PROCEDURE: 1. Seller issues the FCO 2. The buyer physically inspects the goods in Kenya 3. After client�¯�¿�½?�?�¢??s satisfaction, buyer and seller enter into a contract according to their own agreement. 4. Upon signing of the contract, the buyer will cater for the goods insurance, logistics and cutting charges summing to at least 10% of the whole contract value. 5. Note that the above charges are deductible from the final invoice value and the remaining balance of 90% is to be paid in negotiations with some after documentation including Bill of Lading and some balance after the goods arrive to the buyer�¯�¿�½?�?�¢??s final destination port. i.e. (Terms are Negotiable)' 6. After loading, the seller/representative will travel together with the buyer to assist and witness discharge/offloading and to control the wire transfer of the final payment to be made to seller nominated bank account within 48 hours after receipt of the final assay report from buyer�¯�¿�½?�?�¢??s inspection. 7. In future quantities, seller shall notify the buyer of availability and the above procedure will be repeated. DOCUMENTATION: - Commercial Invoice, - Insurance, - Certificate of Origin, - Export permit/Certificate, - Ownership certificate, - Customs Clearance Certificate (Taxes) - Packing list - Bill of Lading

We are a group of companies and one of the prominent traders and suppliers of varied collection of commodities. We have constantly evolved to create a richly diversified line of products from some of the most reputed fields across Africa. Our products are procured from authorized vendors and are in total compliance with set industry norms. On behalf of the Management of Alpha Metal & Chemical Solutions hereby termed as the seller and with full corporate authority and responsibility certifies, represents and warrants to inform you that we are ready, willing and able to supply under the penalty of perjury, the following commodity with its specifications mentioned below. Product Name : Rail Scrap (R50, R65 & HMS) Material : Iron Metal Scrap Application : Melting/Industrial Use Quantity : Agreed shipment/Bulky 50,000 Metric Tonnes Current location : Kenya Country of Origin: Colonial Price :$195 Per Tonne (Negotiable) Contract : CIF Loading Port : Mombasa Delivery : Immediately contract signed by both parties Port Destination : TBA Payment : By TT within 48 hours after delivery and final analysis at the final destination port CHEMICAL COMPOSITION: SCRAP/RAILROAD FERROUS SCRAP (R50/R65) R50 GOST 7173-75 : Weight 51.67 KG/Meter R65 GOST 8165-75 : Weight 64.72 KG/Meter C : 0.60 -0.82% Mn : 0.75 1.05% Si : 0.13 0.28% P : Max 0.035% S : Max 0.045% Ar : Max 0.051% PROCEDURE: 1. Seller issues the FCO 2. The buyer physically inspects the goods in Kenya 3. After client�¯�¿�½?�?�¢??s satisfaction, buyer and seller enter into a contract according to their own agreement. 4. Upon signing of the contract, the buyer will cater for the goods insurance, logistics and cutting charges summing to at least 10% of the whole contract value. 5. Note that the above charges are deductible from the final invoice value and the remaining balance of 90% is to be paid in negotiations with some after documentation including Bill of Lading and some balance after the goods arrive to the buyer�¯�¿�½?�?�¢??s final destination port. i.e. (Terms are Negotiable)' 6. After loading, the seller/representative will travel together with the buyer to assist and witness discharge/offloading and to control the wire transfer of the final payment to be made to seller�¯�¿�½?�?�¢??s nominated bank account within 48 hours after receipt of the final assay report from buyer�¯�¿�½?�?�¢??s inspection. 7. In future quantities, seller shall notify the buyer of availability and the above procedure will be repeated. DOCUMENTATION: - Commercial Invoice, - Insurance, - Certificate of Origin, - Export permit/Certificate, - Ownership certificate, - Customs Clearance Certificate (Taxes) - Packing list - Bill of Lading