Technical sheet Biga’ pick-up: Dimensions: Total Length mm 1541 Width mm. 740 Height mm. 1120 Worktop length mm 95 Width mm. 740 Height from the ground mm. 310 Weight: Total including batteries and banks kg.156 Set 3 banks kg. 4 Batteries kg. 27,5 each x 2 Gear Motor: Permanent magnet engine R.R. 10/1 800 W – rpm 330 – 24 V. Voltage and battery: N. 2 batteries capacity 12V 140 A C20 hermetic gel– connected in series, no maintenance. External battery charger 24 v – 12 amp – electronic microprocessor control- Power 220 v. Differential and transmission: Differential, maximum torque of torsion 2 Kgm - 2 Semiaxis with graft at 6 caves Type 13: transmission chain, Sprocket 13 teeth, Crown wheel 45 teeth, Ratio 1/3,47 Type 19. transmission chain, Sprocket 19 teeth, Crown wheel a 45 teeth, Ratio 1/2,37 Type 23: transmission chain, Sprocket 23 teeth, Crown wheel 45 teeth, Ratio 1/2,00 Type 28: transmission chain, Sprocket 28 teeth, Crown wheel 45 teeth, Ratio 1/1,61 Type 34: transmission chain, Sprocket 34 teeth, Crown wheel 45 teeth, Ratio 1/1,33 Brakes: Front drum brake, activation with right hand Back drum brake, activation with left hand Service brake, activation on left lever. Braking increase by the release of the accelerator (engine brake) enhanced in the setting of the parameters of the junction box. Speed and capacity: Towing besides the driver (performance with the vehicle in perfect efficiency) on flat road. The maximum capacity is considered with uniformly distributed load on the worktop and the center of gravity of the goods must not exceed the height of mm. 350 Type 13 max 5 Km/h +/- 10% P/T 800 kg. on the plane P/T 100 Kg. on slopes 15% Type 19 max 6,5 Km/h +/- 10% P/T 600 kg. on the plane Type 23 max 8,5 Km/h +/- 10% P/T 450 kg. on the plane Type 28 max 10,5 Km/h +/- 10% P/T 300 kg. on the plane Type 34 max 12 Km/h +/- 10% P/T 200 kg. on the plane Tires: Covering: 3.00-4 superelastic rubber Structure: Tubular and sheet Fe 37 polyester powder painted for outdoor use Ral 9007 Lights and Devices: signaling and illumination main headlight and tail lights reverse buzzer, horn.
Advantages of hf technology: Optimal availability for use and long Service life can only be achieved from Motive power batteries when the battery And the charger are perfectly matched. The hf technology provides: Compact wall-mounted designs to save Floor space. Significantly higher electrical Performances. Shorter recharge time, Saving energy, reduction of the batteries Temperature during the cycle, strong Reduction of the co2 emissions, lower Water consumption, which helps prolong The life of the batteries. High production Yield. Soft start mode, customized Charge curve on request. Black hawk is a Versatile device, different charging curve Software could be installed for a specific Customized charging profile for any type Of battery. Usage: suitable for the cyclic recharge Of lead - acid batteries and floating of Sealed gel and / or lead - acid batteries. Optional air pump available Download data available Trough pc/laptop. 230 vca ± 10%, mono-phase, input frequency 50 – 60 hz, efficiency ~ 90%, Operating temperature from– 20 to + 45 °c, current drawn by the battery 0 A if network electrically bonded, protection against output short-circuit with Fuse, protection against polarity reversal with Fuse, thermal protection semi-conductors, input Protection with fuses and varistors, charge curve Programming and settings at will with default iu Ia, displaying and messages with monochromatic 2x20 lcd display – led, audible alarm device, State charge indicator multicolours, thermal Compensation with optional probe, 2 auxiliary Contacts optional configuration at will (mains Presence, finished charge, control pump, etc…), Ventilation forced air circulation, metallic ontainer With dimensions 490 x 360 x 150 mm, weight 11 kg, protection ip20, in conformity with the Low voltage directive 73/23/cee and the emc Directive 89/336/cee and their successive Amendments.
Advantages of hf technology: Optimal availability for use and long s Temperature during the cycle, strong Reduction of the co2 emissions, lower Water consumption, which helps prolong The life of the batteries. High production Yield. Soft start mode, customized Charge curve on request. Black hawk is a Versatile device, different charging curve Software could be installed for a specific Customized charging profile for any type Of battery. Usage: suitable for the cyclic recharge Of lead - acid batteries and floating of Sealed gel and / or lead - acid batteries. Optional air pump available Download data available Trough pc/laptop. 400 vca ± 15%, three-phase, input frequency 50 – 60 hz, efficiency ~ 90%, operating Temperature from– 20 to + 45 °c, current drawn by the battery 0 a if network Electrically Bonded, protection against output short-circuit with fuse, protection against polarity Reversal with fuse, thermal protection semi-conductors, input protection with fuses And varistors, charge curve programming and settings at will with default iu ia, Displaying and messages with monochromatic 2x20 lcd display – led, audible alarm Device, state charge indicator multicolours, thermal compensation with optional Probe, 2 auxiliary contacts optional configuration at will (mains presence, finished Charge, control pump, etc…), ventilation forced air circulation, metallic ontainer with Dimensions 490 x 360 x 150 mm, weight 20 kg (air version 23kg - 503x490x153 Mm), protection ip20, in conformity with the low voltage directive 73/23/cee and The emc directive 89/336/cee and their successive amendments.
Switching technology with microcontroller digital control. They Are flexible and reliable devices. The high efficiency of the battery Chargers assures a remarkable energy saving optimizing the Economic benefits and permitting to amortize the investment for The selection of high frequency in a short time. They are suitable for the recharge of all kind of batteries (leadacid Gel, sealed, agm batteries, etc…) and allow selecting a specific Charge curve or configuring easily a suitable curve for the type of Battery. They are characterized by a negligible residual output ripple. The battery chargers integrate the input and output protections And are equipped with an over-temperature. They have a wholly programmable control unit, easy-to-use thanks To the user-friendly graphic interface displaying all the charge Parameters, the alarms, the data plate and all general information Concerning the device. These kind of battery chargers are equipped With a monochromatic graphic lcd display/led. Technical characteristics: - input voltage: 230 vca ± 10%, mono-phase - input frequency: 50 – 60 hz - efficiency: ~ 90% - operating temperature: – 20 to + 45 °c - current drawn by the battery: 0 a, if network electrically Bonded - protection against output short-circuit: yes, fuse - protection against polarity reversal: yes, fuse - thermal protection semi-conductors: yes - input protection: yes, fuses and varistors - charge curve: programming and settings at Will - default iu ia - displaying and messages: monochromatic 2x20 lcd Display - led - audible alarm device: yes - state charge indicator: yes multicolours
Noiseless and ecological electric vehicole/tractor. 16 Km/h. Direct use: you get on, drive and stop (movement dynamics). For all employees who move in a range greater than 100 mt. For quick repair service and transport of small-sized components. Average time saving of about 40 to 60 minutes per day. TECHNICAL FEATURES: - Turning radius: cm. 120 - Length. 140 - Width cm. 85 - Height. 110-130 - Minimum height from ground cm. 5.4 - Weight: Kg 120/140 depending on the type of batteries installed. - fiberglass shell fully recyclable - tube frame with thick serial number for traceability - Handlebar adjustable in height - cover tires 3.00-4 with room air (can puncture tires) - Headlight and taillight - Safety button "ride-on" - Reverse insertable lever - horn, rear view mirror and the battery charge indicator - Electric motor 24 volt permanent magnet 780 watt - Electronic high-frequency MOSFET technology controlled by a microprocessor to recover energy during braking - N. Two 12-volt batteries - lightweight tubular plate traction - 105/125 Ah. - Built-in charger and automatic battery status. - Drive chain high strength pinion - Differential aluminum satellites treated steel - Shaft couplings with 6 quarries - Voltage reducer 24 to 12 volt lighting system - Brake system: front disc brake, rear differential, brake lever on the left and engine braking enhanced by the setting of the electronic control. - Colors: white, red, green , yellow, blue, black, orange (other colors on request).
Noiseless and ecological electric tractor. 10 Km/h. -offers two different advantages: it allows to move very quickly and transport up to 300 kg of materials by using a truck designed by us. Speedy, handy in narrow spaces, it spins around with the truck within a 200 cm radius allowing quick access to other departments. Quick repair and maintenance of big- sized and heavy materials (the truck is 120x80 cm with a carrying capacity of 300 kg). Allows to avoid using big and expensive vehicles to move small volumes of goods. TECHNICAL FEATURES: - Turning radius: cm. 120 - Length. 140 - Width cm. 85 - Height. 110-130 - Minimum height from ground cm. 5.4 - Weight: Kg 123/143 depending on the type of batteries installed. - fiberglass shell fully recyclable - tube frame with thick serial number for traceability - Handlebar adjustable in height - cover tires 3.00-4 with room air (can puncture tires) - Headlight and taillight - Safety button "ride-on" - Reverse insertable lever - horn, rear view mirror and charge indicator battery 24 volt 800 watt electric motor RR 1/10 - 24 volt electric motor permanent magnet 780 watt - Electronic high-frequency MOSFET technology controlled by a microprocessor to recover energy during braking - N. 2 Batteries 12 volt - tensile tubular plate - 102/157 Ah. - Built-in charger or external high frequency and automatic control of the state of charge. - Traction Chain gear ratio 1/10, 125 - Differential aluminum satellites treated steel - axle shafts with couplings 6 slot - Voltage reducer 24 to 12 volt lighting system - Brake system: front disc brake, rear differential, brake lever on the left and engine braking enhanced by the setting of the electronic control. - Colours: white, red, green, yellow, blue, black, orange (other colors on request).
5 - Foot sheet chariot 5.1 Dimensions: Total length 930 mm Width 650 mm Height 1070 mm Plan Length Width mm 870 mm 620 mm Ground clearance 330 5.2 Weights: Total 77.90 kg including batteries Batteries 13 kg each. x 2 5.3 Motor: Permanent magnet motor with electric 200 W - rpm from 120 to 24 V electro 2Nm 24VDC. 5.4Voltaggio and batteries: N. 2 x 32 A 12 V sealed gel in C5 - series connection, maintenance-free. External charger 24 V - 8 amp - Electronic microprocessor - Power supply 220 V 5.5 Brakes: Electric brake to the engine block, insertion of a power failure. Braking on deceleration (engine braking) enhanced in the setting of parameters control unit. 5.6 Speed and Capacity (performance of the vehicle in perfect working flat route: Maximum speed in 6 seconds of continuous accelerated 5 km / h + / - 10% Max capacity 250 kg and 100kg in terms of gradient of 15%. The maximum flow is considered with uniformly distributed load on the floor. 5.7 Tyres: 2 rubber wheels mounted on wheels with pneumatic 3.00-4 6-ply roofing. 2 wheels 200x50 core diameter polypropylene ring mounted on gray synthetic rubber supports swivel. 5.8 Structure: Tubular and sheet S 235 JR polyester powder coated RAL 6018 external 5.9 Spare parts and tools for maintenance and repair: The original spare parts and tools for maintenance and repair are provided directly Order by Biga spa Italy. 5.10 Values sound level: less than 70 dB (A) 5.11 Environmental conditions: temperature + 5 + 40 C Humidity 50%.
"coreless rewinder rp" is a completely automatic rewinder (roll to roll) that allows to rewind air bubble film for packaging in small rolls without internal core ( pony roll ) This rewinder born following the request of our customers to enter in the markets of hardware store, shopping mall, bricolage shop, etc., where the air bubble film cannot be sold in rolls with standard dimensions, but only in small rolls with few meters. This rewinder remove also the problem of the internal core cost that could be to much expensive if compared to the sold material. The plant is composed by different groups: Unwinder group complete with bearing brackets for the air expansion shaft with pneumatic closing system where the mother roll with an internal core (° 76mm) is loaded Central group complete with motorized nip-roll cylinder and pneumatic cut system with blade; Rewinder group where the material is rewinded without internal core thanks to rewinding rollers, unhooked and the present length and positioned on a basket. The plant also allows, through the application of an adhesive label or tape, to close the produced roll. Control panel where it is possible to set each parameters of production like number of rolls to produce and length. Once inserted the roll of departure, the "coreless rewinder rp" proceeds to the production of the rolls without internal core without any intervention of the operator which is only necessary to load a new mother roll and to remove the produced roll from the basket. The plant is conforming to the ce safety directives and it is furnished complete of manuals of operation and maintenance. Contact us
Sportswear, Newborns, Early Childhood Teenagers And Women..
Plastic cultery, plastic spoon, plastic bottle, cultery sets.
Code ean 4031244780577 Shelf life 18 months Product origin germany directly from manufacturer Paymant: T/T or L/C Size 700g Bib Pcs/case 5 Case per layer 15 Layer per pallet 7 case weight kg 2,80
Code ean 4031244780393 Shelf life 18 months Product origin Germany directly from manufacturer paymant: T/T or L/C size 700 g Bib pcs/case 4 case per layer 15 layer per pallet 7 case wheight kg 2,8
Code ean 4031244780539 Shelf life 18 months Product origin germany directly from manufacturer Paymant: t/t or l/c Size 550 g bib Pcs/case 4 Cases per layer 15 Layer per pallet 7 Case weight kg 2, 20
Code ean 4031244780546 Shelf life 18 months Product origin germany directly from manufacturer Paymant: t/t or l/c Pcs/case 4 Case per layer 15 Layer per pallet 7 Case weight kg 2, 20
Shopping bags pp non woven, polyethylene, biodegradable, juta, paper; non woven garment covers; polyethylene clothes covrs; non woven: spunbond, airlaid, meltblown, spunlace. pellet en plus a1, din plus. photovoltaic panels. medical disposables: face mask, adult bibs, gloves; stretch film packaging; mail bags courier bags poly; pet food packaging bags plastic; disposable horeca; seat covers automotive plastc, non woven;.
Electronic chip set.
Diapers Pillo New-Born A selection of products 100% Made in Italy, Designed to guarantee a long dry sensation 1.Dryway technology with 3 draining channels. 2. Wet indicator 3. Stackable adhesive 4. Elastic bands 5. Premium materials We use only certified cellulose that comes from sustainably managed forests (PEFC and FSC certifications) We do not use chlorine, perfumed lotions, heavy metals or lead to ensure a lower impact on the ecosystem. (EFC Certification)
Diapers Pillo Mini. A selection of products 100% Made in Italy, Designed to guarantee a long dry sensation 1.Dryway technology with 3 draining channels. 2. Wet indicator 3. Stackable adhesive 4. Elastic bands 5. Premium materials We use only certified cellulose that comes from sustainably managed forests (PEFC and FSC certifications) We do not use chlorine, perfumed lotions, heavy metals or lead to ensure a lower impact on the ecosystem. (EFC Certification)
Diapers Pillo Midi. A selection of products 100% Made in Italy, Designed to guarantee a long dry sensation 1.Dryway technology with 3 draining channels. 2. Wet indicator 3. Stackable adhesive 4. Elastic bands 5. Premium materials We use only certified cellulose that comes from sustainably managed forests (PEFC and FSC certifications) We do not use chlorine, perfumed lotions, heavy metals or lead to ensure a lower impact on the ecosystem. (EFC Certification)
Diapers Pillo Maxi A selection of products 100% Made in Italy, designed to guarantee a long dry sensation 1. Dry for 12 hours 2. Anatomical and ultra-thin 3. Protective on the skin 4. Soft 3D embossed structure 5. Premium materials 6. Elastic bands 7. Dryway technology with 3 draining channels 8. Stackable adhesive. We use only certified cellulose that comes from sustainably managed forests (PEFC and FSC certifications) We do not use chlorine, perfumed lotions, heavy metals or lead to ensure a lower impact on the ecosystem. (EFC Certification)
